The startup.nsh file is useless to boot EFI payloads. We just need to
follow the naming detection specified in the UEFI spec.
The EFI payload need to be placed in the boot/efi folder in the EFI partition
and follow the architecture naming as described below:
32bit : bootia32.efi
x64 : bootx64.efi
aarch32 : bootarm.efi
aarch64 : bootaa64.efi
This naming is already right in the packages involved (systemd, grub2,
gummiboot), therefore we just need to drop the generation of the
startup.nsh file.
The usage of the startup.nsh in genimage is also dropped to avoid errors in
the image generation.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Tested-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
For the i.MX8 often an Image.gz is built. With these changes, if
BR2_LINUX_KERNEL_IMAGEGZ=y, the correct Image.gz file is now put into
the generated image instead of falling back to the non-existent zImage.
Signed-off-by: Hanspeter Portner <dev@open-music-kontrollers.ch>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This patch adds runtime testing of the OCI archive created by the
sloci scripting. It launches a containerd instance, imports, and
runs the OCI container.
The existing QEMU AARCH64 kernel config was extended to enable common
options used by a container runtime (cgroup and overlayfs).
Signed-off-by: Matthew Weber <matthew.weber@collins.com>
[Arnout: adapt file name which is arm64 now; add to DEVELOPERS]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Update STM32F469-disco configuration files to operate with new kernel.
Result of make tinyconfig was taken as a starting point to fit kernel
into flash memory.
Current setup kernel + rootfs fits in 1.6MB on-chip flash memory
Fixes:
- Move kernel to new flash bank due to growth of dtb size
- Fix kernel start address in bootloader
- Remove outdated path which doesn't affect normal operation mode
For better binary size optimization gcc LTO is turned on.
Signed-off-by: Yauheni Saldatsenka <eugentoo@gmail.com>
[Arnout:
- squash 3 patches into 1;
- remove unused dts file;
- move linux/linux.config to linux-xip.config;
- add a sentence to readme to say SD card is not needed.
]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Old scripts are still used by a10_olinuxino & a20_olinuxino_micro
Fixes olimex_a20_olinuxino_micro
see https://gitlab.com/buildroot.org/buildroot/-/jobs/1478738568
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The default setting with miniuart-bt requires hciattach which is a
deprecated utility in BlueZ. Setting the krnbt parameter switches to
the modern method of using serdev in the kernel removing the need for
any userspace configuration to enable the Bluetooth controller.
This is documented as applying to all Raspberry Pi variants so just
enable it globally.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently mx6cubox uses a custom boot.scr.txt script
and custom image generation scripts: genimage.cfg, post-build.sh
and post-image.sh.
Switch to using the more standard extlinux.conf solution
and remove the custom scripts in favor of the standard
board/freescale/common/imx/post-image.sh one.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
a10_olinuxino is not switched to extlinux.conf, so the broken symlinks
are replaced by the previous content from a20_olinuxino.
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
imx7d-sdb has been converted to use disto boot in U-Boot.
Add extlinux.conf support so that the board can boot correctly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Pierre-Jean Texier <texier.pj2@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently, only SPL is supported when BR2_LINUX_KERNEL_INSTALL_TARGET=y
is selected.
Support non-SPL case too.
This is needed for booting imx7d-sabresd, for example.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Pierre-Jean Texier <texier.pj2@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently wandboard uses a custom boot.scr.txt script
and custom image generation scripts, genimage.cfg and
post-build.sh.
Switch to using the more standard extlinux.conf solution
and remove the custom scripts in favor of the standard
board/freescale/common/imx/post-image.sh one.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Running stm32mp1 watchdog is properly recognized and handled by kernel
watchdog framework since Linux v5.6.
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Pierre-Jean Texier <texier.pj2@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Running stm32mp1 watchdog is properly recognized and handled by kernel
watchdog framework since Linux v5.6. For details see the Linux commit
85fdc63fe256 ("drivers: watchdog: stm32_iwdg: set WDOG_HW_RUNNING at
probe"). So U-Boot config fragment can be safely removed without
adding userspace watchdog daemon.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The stm32mp157 images successfully boot only once. Subsequent boot
attempts fail to reach U-Boot. The root cause turns out to be in U-Boot
corruption during the first boot. The stm32mp1 U-Boot stores its
environment at the end of GPT partition named 'ssbl' since v2020.10-rc2.
However Buildroot genimage template for stm32mp157 boards creates 'ssbl'
partition w/o extra space for U-Boot primary and redundant environments.
This patch explicitly specifies 'ssbl' partition size that should be
enough for both u-boot.stm32 image (~1M) and both environments (16K).
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Tested-by: Pierre-Jean Texier <texier.pj2@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
In new kernels sunxi-mmc driver has been switched to asynchronous probe.
As a result, mmc (SD/eMMC) indexes can be shuffled breaking board boot.
Switch to GPT partitions to use partition labels instead of explicit
mmcblk device names. Note that the default GPT partition table location
conflicts with the SPL location, so move GPT table after bootloaders.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Update the commit id for u-boot to include fixes from the starfive-tech
u-boot repository:
494e5ef7b807 jh7100: Enable full 2M L2 cache
4571f5a4e1e4 vic7100: enable cache ways (L2 cache)
abb06422a5cd Remove fdt_high and initrd_high for Starfive
93099a61c7b0 starfive: beaglev: Disable SIFIVE_CLINT and enable RISCV_TIMER
bfb5abac3d1f Revert "riscv: Enable the SiFive CLINT block driver in S-Mode(VIC7100 ONLY)"
7b70e1d44ba9 defconfig: enable cache_wayenable for better performance
7c585978616b configs: earlycon=sbi is deprecated
The commit abb06422a5cd ("Remove fdt_high and initrd_high for Starfive")
has removed the need for buildroot to patch the fdt_addr_r address.
Update linux from commit in the old 5.10 branch that Fedora image was
using to head of esmil_starlight branch [1] which is currently based
on 5.13-rc5 and represents the best kernel for this board [2]. This
commit was tagged as buildroot-20210609 because the branch gets rebased
regularly.
In addition, the updated kernel now has jh7100-beaglev-starlight.dtb so
buildroot no longer needs to copy the dtb from u-boot.
[1] https://github.com/starfive-tech/linux/tree/esmil_starlight
[2] https://github.com/starfive-tech/linux/issues/26
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[Arnout: add comment to refer to the tag in linux repo]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Update the chromebook elm configuration to use v5.10 which is an LTS.
With v5.10, none of the patches previously needed to enable the display
are needed anymore. Deleting them and making minor updates to the linux
kernel configuration.
Signed-off-by: Bilal Wasim <bilal.wasim@imgtec.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
[yann.morin.1998@free.fr: drop "exit $?" in post-image.sh]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Bump U-Boot and Linux kernel versions. Updating U-Boot to 2021.04
requires the following two changes.
First, after switching to binman, u-boot.itb is no more generated for
64-bit sunxi boards. Combined u-boot-sunxi-with-spl.bin image should
be used instead. This image contains SPL, U-Boot, and FIT image,
where FIT image contains other binaries such as BL31 and SCP.
Second, new U-Boot enables support for System Control Processor (SCP)
firmware. SCP firmware is included by default into FIT image in the
combined u-boot-sunxi-with-spl.bin binary. When SCP is not available
or not needed, it should be explicitly disabled by pointing to an
empty file. Support for Allwinner SCP firmware is not yet available
neither in Buildroot nor in mainline kernel. So disable it for now
using custom U-Boot build options.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
gcc-11 warns about what appears to be an out-of-range array access but
stop the build due to -Werror added to cflags:
arch/sparc/kernel/mdesc.c: In function 'mdesc_node_by_name':
arch/sparc/kernel/mdesc.c:647:22: error: 'strcmp' reading 1 or more bytes from a region of size 0 [-Werror=stringop-overread]
647 | if (!strcmp(names + ep[ret].name_offset, name))
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/sparc/kernel/mdesc.c:77:33: note: at offset 16 into source object 'mdesc' of size 16
77 | struct mdesc_hdr mdesc;
| ^~~~~
arch/sparc/kernel/mdesc.c: In function 'mdesc_get_property':
arch/sparc/kernel/mdesc.c:692:22: error: 'strcmp' reading 1 or more bytes from a region of size 0 [-Werror=stringop-overread]
692 | if (!strcmp(names + ep->name_offset, name)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/sparc/kernel/mdesc.c:77:33: note: at offset 16 into source object 'mdesc' of size 16
77 | struct mdesc_hdr mdesc;
| ^~~~~
arch/sparc/kernel/mdesc.c: In function 'mdesc_next_arc':
arch/sparc/kernel/mdesc.c:719:21: error: 'strcmp' reading 1 or more bytes from a region of size 0 [-Werror=stringop-overread]
719 | if (strcmp(names + ep->name_offset, arc_type))
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/sparc/kernel/mdesc.c:77:33: note: at offset 16 into source object 'mdesc' of size 16
77 | struct mdesc_hdr mdesc;
| ^~~~~
cc1: all warnings being treated as errors
The issue was initially reported to gcc [1] where it was analized.
As suggested, change the struct mdesc_elem * accesses from the end
of mdesc to those from the beginning of the data array.
Update the prototype of node_block(), name_block() and data_block()
since the code really seems to want to do is to compute the address
somewhere into the chunk pointed to by hp.
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100262
Upstream status: Pending
https://www.spinics.net/lists/sparclinux/msg26385.html
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
As described by [1], the kernel generated by the configuration for the
STM32f469 Discovery board is buggy. Using a newer kernel, as suggested
by [1], increases the dtb and Kernel image size. In particular, the
5.12 version of the kernel generates a dtb and a kernel image whose sum
exceeds the 2 MByte of the flash module.
So I decided to replace the afboot-stm32 bootloader in the flash with
U-boot to easily boot the system from sdcard without having to worry
about the size of dtb, kernel and rootfs generated by the configuration.
This solution allows you to fix the kernel boot issue and makes it
possible to use its future versions.
[1] http://buildroot-busybox.2317881.n4.nabble.com/Bug-11746-New-stm32f469-didn-t-work-correctly-td219644.html
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Acked-by: Christophe Priouzeau <christophe.priouzeau@foss.st.com>
Tested-by: Christophe Priouzeau <christophe.priouzeau@foss.st.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout:
- specify headers version explicitly, even though it's default;
- bump kernel to 5.12.11]
Fixes https://gitlab.com/buildroot.org/buildroot/-/jobs/1297337965
Commit 15a2f9b819 (package/{mesa3d, mesa3d-headers}: bump
version to 21.0.2) marked BR2_PACKAGE_MESA3D_DRI_DRIVER_SWRAST as legacy,
but forgot to update the defconfig. The SW rasterizer isn't really needed
with the Intel GPU, so just drop it.
In addition, X11 now needs some help with loading the modules in the correct
order, similar to how it was done for the test in commit 4a3639bad0
(support/testing: test_glxinfo load X11 modules in the right order).
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Add the new SAMA5D2 ICP (Industrial Connectivity Board)
with linux4sam_2020.10 components.
Update README file with new defconfigs.
https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d2IcpMainPage
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The OMAP5432 uEVM[1] is a development board from Texas Instruments.
It is similar to the OMAP4 Panda boards, from which this configuration is
inspired.
[1]: https://svtronics.com/5432
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This introduces a configuration for the SBSA reference machine under
QEMU that is intended for developing and testing firmware. It consists
of ATF that load EDK2 as BL33 which in turn will load GRUB2.
Included with the board files is a minimal kernel configuration, almost
identical to that of board/qemu/aarch64-virt/linux.config. The main
difference is the addition of ACPI which is preferred over DTB for
booting an UEFI system.
Signed-off-by: Dick Olsson <hi@senzilla.io>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This host utility is useful to recover the bootloader.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This commit extends the beaglev_defconfig and its documentation to
build the low-level firmware, and to explain how to reflash it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[yann.morin.1998@free.fr: use typoed-name for beaglev-ddrlnit]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This commit introduces support for the RISC-V based BeagleV platform,
which uses a Starfive JH7100.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
[yann.morin.1998@free.fr: use: eval $(make printvars)]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
- Bump kernel to version 5.11.16.
We remove the hardcoded ttyAMA0 and rely on the firmware to discover our
console. This enables serial console on systems, which do not have an Arm
pl011 UART.
We switch to GPT disklabel and discover our root filesystem using its
PARTLABEL. This enables booting from more media, such as HDD, SD card or
USB.
We update the readme, which hinted that ACPI was mandatory. This is not
strictly the case as we can also boot with a dtb and/or a U-Boot based
firmware, with no ACPI. While at it, mention EBBR, SystemReady and explain
how to build and use a U-Boot-based qemu firmware.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Erico Nunes <nunes.erico@gmail.com>
Reviewed-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add mention about nitrogen8mp_defconfig which is meant for our
Nitrogen8MPlus SOM device.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
- Add support for 8M Plus CPU (A1 and A0 silicon)
- Simplify cpu type parsing
- Update to be closer to Yocto counterpart
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The Acqua A5 is a system on module based on the Microchip SAMA5D31 SoC:
https://www.acmesystems.it/acqua
It is available in both 256 MiB and 512 MiB versions, hence the two
defconfig files. These configs build microSD card images with:
- AT91Bootstrap 3
- Linux 5.4.107
- default buildroot packages (uClibc, Busybox)
The device tree blob comes from Acme Systems:
https://github.com/AcmeSystems/dts-archive
It is licensed under GPLv2 or later.
Signed-off-by: Edgar Bonet <bonet@grenoble.cnrs.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 5502a889dd
("configs/beaglebone_qt5: don't use custom post-image script") removed the use
of genimage_linux41.cfg but didn't remove the file.
Signed-off-by: Michael Nosthoff <buildroot@heine.tech>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Almost identical as i.MX 8M Nano, with a couple of differences:
- different ATF load address [1]
- different entry point [2]
[1] e8e2703a30
[2] https://source.denx.de/u-boot/u-boot/-/blob/v2021.04-rc4/configs/imx8mp_evk_defconfig#L14
Signed-off-by: Stephane Viau <stephane.viau@oss.nxp.com>
Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Bump TF-A to version 2.4.
- Bump u-boot to version 2021.01.
- Bump kernel to version 5.11.3.
We switch TF-A to a single FIP image. Thanks to this, TF-A does not need to
use semihosting to load the various BL* anymore (but U-Boot still does).
Update the readme.txt accordingly.
We switch to a u-boot image for the ramdisk. This removes the need to
update the fdt chosen node manually in the bootcmd.
While at it, we drop the generation of the kernel dtb, which we do not use.
In this config, we are indeed using the dtb generated on-the-fly by qemu
and amended by TF-A.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Gerome Burlats <gerome.burlats@smile.fr>
Cc: Romain Naour <romain.naour@gmail.com>
Cc: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Romain Naour <romain.naour@gmail.com>
Tested-by: Romain Naour <romain.naour@gmail.com>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This adds a 32-bit equivalent configuration of ppc64-e5500 board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
We have defconfigs for quite a few friendlyarm boards, but the
naming for the defconfigs for those boards is inconsistent: some
start with 'friendlyarm_' while others don't.
Although the number of boards starting with 'friendlyarm_' is
less than those which do not, we still choose to rename the
boards so all have the 'friendlyarm_' prefix.
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Chakra Divi <chakra@openedev.com>
Cc: Davide Viti <zinosat@gmail.com>
Cc: Marek Belisko <marek.belisko@open-nandra.com>
Cc: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Very similar to the other stm32mp157-based boards, except that we use the
multi_v7 defconfig for ease of maintenance.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The mmc probing order has changed since commit 21b2cec61c04bd1 (mmc: Set
PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4), so get rid of
the hardcoded root=/dev/mmcblk1p2. The old vendor U-Boot unfortunately does
not have GPT support, so stick to MBR and use the legacy
root=PARTUUID=<disksignature>-<partition> format and set a fixed disk
signature, similar to how it was done for orangepi-r1 in commit 34cce93adb
(configs/orangepi_r1_defconfig: bump kernel to 5.10.10, u-boot to 2020.10).
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
In commit 38d04e6b13, I did a last-minute change by adding the comment
to explain where the PARTLABEL was coming from, and introduced a typo in
that comment.
Fix it.
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Patch that pins mmc indexes was not accepted to mainline kernel. Drop that
patch and switch to GPT to use partition labels. For GPT the name of the
partition in genimage.cfg is used as the label for that partition. Note
that the default GPT partition table location conflicts with the SPL
location, so move GPT table after bootloaders.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Update to use the official linux kernel v5.10 instead of an
out-of-tree kernel, and use the official U-Boot v2021.01 as the
bootloader. Provide two configuration files of genimage for different
boot flows:
- Boot from SD card (default)
- Boot from SPI flash
A boot script is generated to automatically boot the distro.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
So the normal DHCP-on-eth0 logic works for the graphical defconfig where
eudev is used.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Explicitly enable PCI support in the kernel after commit eb01d42a77785 (PCI:
consolidate PCI config entry in drivers/pci) and change to GPT partitions /
root=PARTLABEL to find the rootfs instead of hardcoding /dev/mmcblk2p2 as
the mmc probing order has changed since commit 21b2cec61c04bd1 (mmc: Set
PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4).
This has the additional advantage that the same image will work when written
to a USB drive instead of a microsd.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump Linux to 5.10.10 and U-Boot to 2020.10. In the new kernel sunxi-mmc
driver has been switched to asynchronous probe. As a result, mmc indexes
can be shuffled breaking board boot. Add patch that pins mmc indexes to
their original ordered values.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit adds support for Sinovoip's Banana Pi
M1+. It is mostly based on bananapro_defconfig
but with appropriate device tree and minor tweaks:
- apply bananapi-m1-plus device tree in linux
- apply bananapi_m1_plus defconfig for uboot
- apply patch for OOB IRQs on new device tree
- update device tree name in boot.cmd, genimage.cfg
- update symlink for BRCM driver in rootfs_overlay
- overall clean-up of the config
Tested on BPI-M1+ V1_1.
Signed-off-by: Filip Skoneczny <fskoneczny@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
GPT provides partition labels, which can be used to tell the kernel to find
the rootfs based on it (root=PARTLABEL=rootfs) as a nicer/more extensible
solution than the MBR disk signature / PARTUUID.
When using GPT, the name of the partition in genimage.cfg is used as the
label for that partition.
The default GPT partition table location unfortunately conflicts with the
SPL location, so move the 16KB GPT table after it.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
[yann.morin.1998@free.fr: add the comment about 'rootfs']
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The probing order of the two mmc controllers (sdcard and sdio wifi) has
changed in kernel 5.10 since commit 21b2cec61c04bd1 (mmc: Set
PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4), so change to
root=PARTUUID=.. instead of hardcoding /dev/mmcblkXp2.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
[yann.morin.1998@free.fr: use feedc0de as magic]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
HDMI support is enabled by default in sunxi_defconfig since commit
c822a3ec17 (ARM: configs: sunxi: Add DRM output-related options), so drop
from fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Support for this board was removed in Linux upstream [1] since Xilinx
new design tools dropped these platforms in 2013, along with all
PPC405/PPC440 new designs. They are not maintained nor tested anymore.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7ade8495dcfd788a76e6877c9ea86f5207369ea4
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump most QEMU defconfigs (every one that was previously on 5.4.y)
to latest longterm kernel 5.10.7.
Please note the following exceptions/modifications:
- board/qemu/qemu_s390x_defconfig: ignored (already up to date)
- board/qemu/sh4*-r2d:
- Remove the remaining kernel patch [1] provided by Alan Modra
fixing rodata alignment, carried here by Romain Naour [2] to
fix an issue preventing kernel from booting with binutils 2.23.
Patch is present in upstream Linux now.
- Fix compile-time error regarding 64-bit time data structures
from kernel headers when building with uclibc. Previous fix [3]
existed upstream; but see details below.
- board/qemu/ppc-mpc8544ds: Updated kernel patch
- board/qemu/arm-versatile: Updated kernel patch
- board/qemu/mips*r6*: Updated kernel patch
Tested on all configs/qemu* configurations. [4]
[1] https://www.sourceware.org/ml/binutils/2019-12/msg00112.html
[2] https://git.busybox.net/buildroot/commit/?id=a2331c8a61bdd71c47492efc818fb0458a349219
[3] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=fc94cf2092c7c1267fa2deb8388d624f50eba808
[4] https://gitlab.com/clumsyape/buildroot/-/pipelines/244024195
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Integrate the RCW into the storage device image, so the image can also
be used a boot source. The SoC expects the RCW at offset 4096 of the SD
card or eMMC.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Enable building of the bootloader and integrate it into the resulting
image.
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Bump QEMU defconfigs to latest longterm kernel 5.4.88.
Please note that QEMU boards not based on 5.4.y were ignored:
- qemu_csky810_virt_defconfig
- qemu_csky807_virt_defconfig
- qemu_csky610_virt_defconfig
- qemu_csky860_virt_defconfig
Tests were carried out on all QEMU boards using Gitlab [1] (commit
message was slightly different, but the patch is identical)
Additional actions needed were:
- board/qemu/sh4-r2d: Remove one of the two kernel patches [2] provided
by Alan Modra fixing rodata alignment, carried here by Romain Naour [3]
to fix an issue preventing kernel from booting with binutils 2.23.
Patch is present in upstream Linux now.
[1] https://gitlab.com/clumsyape/buildroot/-/pipelines/239483891
[2] https://www.sourceware.org/ml/binutils/2019-12/msg00112.html
[3] https://git.busybox.net/buildroot/commit/?id=a2331c8a61bdd71c47492efc818fb0458a349219
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add the new SAM9X60 Evaluation Kit with linux4sam_2020.04
components. Update README file with new defconfigs.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Re-introduced rock64_defconfig which was dropped by commit
a5fa2469e6 ('Revert
"configs/rock64_defconfig: remove defconfig"').
Signed-off-by: Min Xu <xuminready@gmail.com>
Tested-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
It may be useful for users using Boundary Devices boards to find
more advanced defconfigs that the one provided by Buildroot.
See:
https://github.com/boundarydevices/buildroot-external-boundary#configurations-details
Update the readme.txt to add the link to the br2_external maintained
by Boundary Devices.
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Cc: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Remove the note about non-working network. This was actually fixed with
linux kernel 5.9. This board is now on 5.10.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
weston does not work on the ti-sgx SDK, so switch to using KMS directly,
and drop the wayland-related config options.
Signed-off-by: Adam Duskett <Aduskett@gmail.com>
[yann.morin.1998@free.fr: split into its own patch]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
When tags was added by commit 011206b2bf
to detect the qemu command line, the qemu_arm_vexpress_tz_defconfig
was ignored due to a build issue.
This build issue has been fixed by previous patches, so we can
enable the runtime testing by adding the tag in the readme.txt
and the post-image script in the defconfig.
Since Qemu from HOST_DIR is now executed directly from BINARIES_DIR,
we can remove all the string before "qemu-system-*".
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Usually the qemu command line start directly with "qemu-system-<arch> ...".
But the command line for qemu_arm_vexpress_tz_defconfig start by doing
"cd output/images && ../host/bin/qemu-system-arm". This is necessary
since boot binaries, except BL1, are primarily loaded via semi-hosting
so all binaries has to reside in the same directory as QEMU is started
from [1].
To order to handle this case correctly, update the post-image.sh used
by all qemu defconfigs to execute qemu from BINARIES_DIR.
Since we have to change the current directory use a subshell to
restore the current directory after Qemu execution.
[1] 4ebbea9592/docs/plat/qemu.rst
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The output/images directory is called BINARIES_DIR in the
Buildroot manual, not IMAGE_DIR.
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Bump to the latest kernel v5.9.11 and require openssl.
- Switch to PSCI for bringing up the secondary CPUs.
- Switch to GICv3.
- Update the instruction in the readme.txt to use the latest FVP v8
Foundation Platform 11.12 build 38, and to start 4 cores in SMP.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Orangepi Zero Plus board:
- U-Boot 2020.10
- Linux 5.7.19
- Default packages from buildroot
This patch is based on Orangepi Zero Plus2 board support, so genimage
configuration and description is copy pasted. One difference is that
newer Linux and U-Boot are selected. Another difference is Ethernet
support (Plus) instead of WiFi (Plus2).
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
For grub-efi we can align the rootfs to start at exactly 16MB from the
beginning of the disk. This can be done by reducing the vfat partition to
be 32 KB smaller than its 16MB size, just like the offset of the vfat
partition.
Signed-off-by: Florian La Roche <Florian.LaRoche@gmail.com>
[Peter: drop redundant offset/size settings, add comment]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As resizing the rootfs partition using a partition manager can result
in a non booting image due to the firmware's location, removal of the
size limit for the rootfs allows better match size-wise.
Signed-off-by: Dagg Stompler <daggs@gmx.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
U-Boot 2020.10 no longer provides boot command in default environment for
Udoo Quad/Dual board. Boot script needs to be added to the image. In order
to keep using common infrastructure for freescale boards, move boot files
to root filesystem and add boot script there. Also switch Udoo Neo board
to common freescale infrastructure to simplify maintenance.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
After BSP update Udoo Quad/Dual board once again hangs on boot. On a
new kernel disabling CONFIG_USB option is not enough to work around
the troublesome usb host on Udoo Quad/Dual board. So in order to be
future-proof it makes sense to disable usbh1 block in device tree
rather than fine-tune kernel configuration after BSP updates.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit changes the stm32mp1 configurations to use the TF-A ->
U-Boot boot flow (called "trusted boot flow" by ST) instead of the
U-Boot SPL -> U-Boot boot flow. ST recommands this trusted boot, and
it's also the only one that allows to use the STM32 Cube Programmer
for reflashing devices.
As part of this, the genimage configuration file is now generated, as
it contains some file names that depend on the platform. Removing
partition-type from genimage.cfg is mandatory, since it would cause a
hybrid MBR partition table to be created, which itself would prevent
ATF from finding the ssbl parition.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Starting with linux kernel v5.9 all required configuration options are
available in the default config.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since 2020.04 version, the enumeration of MMC has changed, so the boot
script must be updated
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the chromebook elm configuration to use v5.9 instead of an
intermediate release candidate.
At the latter stages of the v5.9 release, a patch was added which
broke the Chromebook Elm HDMI. Therefore add a revert patch to get rid
of this problem. The fix (and the revert) are already on the mailing
list (https://lkml.org/lkml/2020/10/10/32) and should become available
with v5.10
Signed-off-by: Bilal Wasim <bilal.wasim@imgtec.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since 52f188140c (qemu version bump to 5.1),
the image generated by qemu_riscv64_virt_defconfig doesn't boot anyore with
the following error:
rom: requested regions overlap (rom phdr #0: [...]/images//fw_jump.elf. free=0x000000008000e240, addr=0x0000000080000000)
qemu-system-riscv64: rom check and register reset failed
Update the qemu command line as described in the Qemu wiki for riscv64 [1]
Fixes:
https://gitlab.com/jugurthaB/buildroot/-/jobs/686104707
[1] https://wiki.qemu.org/Documentation/Platforms/RISCV#Booting_64-bit_OpenEmbedded_Images
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Jugurtha BELKALEM <jugurtha.belkalem@smile.fr>
Cc: Alistair Francis <alistair.francis@wdc.com>
Cc: Mark Corbin <mark@dibsco.co.uk>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
[yann.morin.1998@free.fr:
- don't force network range
- don't forward TCP port
- drop post-build script to add tty1
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This commit adds supports for building buildroot kernel + rootfs
for MT8173 Elm board, also known as Chromebook Elm
(https://www.acer.com/ac/en/US/content/series/acerchromebookr13).
Though Chrome-OS is officially supproted on this board, the
mainline kernel works as well (benchmarks + conformance), and so
the 5.9 kernel is used. As the 5.9 kernel isn't yet released, we
use the 5.9-rc5 for now, which will be up-revd to 5.9 once its
released.
Using the mainline kernel means that we have to apply certain patches
to get the HDMI screen working. These patches are lying in the
"drm-misc-next" list and will make it to the kernel after 5.9. At that
time, we will remove the patches and point Buildroot to use the latest
kernel (hopefully, 5.10).
This commit also adds an ITS file (for creating FIT images), an ARGS
file (for providing kernel args) and a "sign.sh" script to generate
signed kernel images. Though the "sign.sh" is very similar to the
coresponding file under board/chromebook/snow, it cannot be shared
between both boards, as the script requires access to the board
specific its / args file.
Additionally a readme & defconfig is added to help the user get started.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The same script is going to be used by the Chromebook Elm to generate
a bootable SD / USB image. Therefore, move the script out of the snow
folder to one level above (board/chromebook/snow -> board/chromebook).
Update the chromebook_snow_defconfig to reflect the new location of
the script.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for imx8mqevk_defconfig that allows booting a mainline
kernel.
This defconfig still relies on NXP ATF and U-Boot, but in the long term
the plan is to switch to mainline ATF and U-Boot as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Analog audio is enabled by default in sunxi_defconfig since commit 5d2408c6
(ARM: configs: sunxi: Add sun8i analog codec), so drop from fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Now that upstream supports this board add buildroot support for it,
too.
This supports:
- latest upstream linux kernel. Since the support for this board and
its SoC is still in active development, we want to follow the
upstream kernel releases for now.
- building an image which can be installed to eMMC, SD card or USB
thumb drive.
- upstream u-boot patches are pending, therefore no support for
building a bootloader for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Now that RISC-V 32-bit (RV32) support has been merged into mainline
glibc, we can use the Linux 5.4 kernel.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The apu2 by PC Engines is a 64 bit single board computer with coreboot
BIOS. It only has serial output, but no graphics chip. With its 2–4
ethernet ports, it is often used to build a firewall or router.
The provided defconfig configures busybox and isolinux. It will output
a hybrid ISO image that can be written to a USB stick or burned to a
CD.
Configuration based on a blogpost by Tony Arkles:
http://www.better-bsp.com/blog/2017/03/02/buildrooting-for-apu2/
Signed-off-by: Danilo Bargen <mail@dbrgn.ch>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A defconfig for the friendlyarm nanopc-t4 was added in
c23895f06e, but then removed
in 8efd4463f7 because an ARM32
compiler was needed to build ATF, and this was not supported
back then.
Now, since package/arm-gnu-a-toolchain/ has been added, this
defconfig can be re-introduced.
Following new changes are introduced in comparision with the
older changeset:
- updated readme
- GPT partition layout is being used
- update defconfig to build ATF
- bump u-boot to 2020.07
- bump linux to 5.8.2
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: fixate U-Boot version; remove blind BR2_TARGET_UBOOT_NEEDS_PYTHON]
A defconfig for the friendlyarm nanopi-m4 was added in
493c3979a4, but then removed
in a24bd8936f because an ARM32
compiler was needed to build ATF, and this was not supported
back then.
Now, since package/arm-gnu-a-toolchain/ has been added, this
defconfig can be re-introduced.
Following new changes are introduced in comparision with the
older changeset:
- readme updated
- GPT partition layout
- update defconfig to build ATF
- bump u-boot to 2020.07
- bump linux to 5.8.2
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: fixate U-Boot version; remove blind BR2_TARGET_UBOOT_NEEDS_PYTHON]
A defconfig for the rockpro64 was added in
59e1077b4e, but then removed
in 10f49213b7 because an ARM32
compiler was needed to build ATF, and this was not supported
back then.
Now, since package/arm-gnu-a-toolchain/ has been added, this
defconfig can be re-introduced.
Following new changes are introduced in comparision with the
older changeset:
- renamed defconfig from pine64_rockpro64 to rockpro64
- updated readme
- using a GPT partition layout
- update defconfig to build ATF
- bump u-boot to 2020.07
- bump linux to 5.8.2
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: fixate U-Boot version; remove blind BR2_TARGET_UBOOT_NEEDS_PYTHON]
Mainline Linux now has basic s500/roseapplepi support, so switch to that to
get rid of the dependency on gcc7. Add two patches for the dts / fix that
didn't make it for kernel 5.7.
The mainline kernel does not yet have support for the mmc interface, so
change to initramfs for now. Patches for mmc support have been posted
recently, so this can be reverted once they show up in a stable kernel:
https://lore.kernel.org/lkml/cover.1593124368.git.cristian.ciocaltea@gmail.com/
The owl serial port is called ttyOWLn in mainline, so adjust the bootargs to
match. Also drop the unneeded execute permission on uEnv.txt.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for RK3288 SOM based radxa rockpi-n8
target with below features:
- Custom U-Boot 2020.07-rc4
https://github.com/amarula/u-boot-amarula.git
commit: "ba120841bf40ebaed049d64bb4f980083a1cf6b7"
- Custom Linux 5.7.0-rc1
https://github.com/amarula/linux-amarula.git
commit: "5dcb0132685b07beb82065c5d7521e6c555c55b6"
- GPT partition layout is being used
- Default packages from buildroot
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/674933582
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Signed-off-by: Oleksandr G Zhadan <Oleks@ArcturusNetworks.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The Banana Pi M2 Zero [1] is a board from Sinovoip, based on the
Allwinner H2+ SoC.
It is similar to the other Banana Pi M2* boards, from which this
configuration is inspired.
[1]: http://www.banana-pi.org/m2z.html
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With this patch we enable CONFIG_USB for HSDK, which is not explicitly
selected by UDL since the commit 5d50bd440bc2 ("drm/udl: Make udl
driver depend on CONFIG_USB"). Commit 4c13ca86dcf8 ("ARC:
[plat-hsdk]: fix USB regression") is not yet backported to Linux
kernel 5.6.x, so we enable this option in fragment file for HSDK.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Basic support for the Marvell ESPRESSObin, by Globalscale Technologies.
http://espressobin.net
The kernel config has been extended with a fragment to enable switchcore
support, DSA drivers, and VLAN filtering in the bridge. To make use of
this you need a custom libnl based application, or the iproute2 suite
rather than the brctl tools, which don't support the VLAN filtering.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for imx6ullevk_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add the new SAMA5D27 WLSOM1 Evaluation Kit with linux4sam_6.2
components. Update README file with new defconfigs and new
packages/website.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since commit 'package/rpi-firmware: fix startup file names' ([1]) the
start and fixup file names are normalized to start.elf/fixup.dat,
adjust the rpi4 genimage config files accordingly.
Fixes:
ERROR: file(rpi-firmware/fixup4.dat): stat(.../images/rpi-firmware/fixup4.dat) failed: No such file or directory
ERROR: vfat(boot.vfat): could not setup rpi-firmware/fixup4.dat
[1] https://git.buildroot.net/buildroot/commit/?id=1bdc0334ff6273761b2e7fda730cdcc7e1f46862
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for RK3399 based rockpi-4 targets (model A, B, C)
with below features:
- Custom U-Boot 2020.07-rc4
https://github.com/amarula/u-boot-amarula.git
branch rock-pi
- Linux 5.4.46
- GPT partition layout is being used
- Default packages from buildroot
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for RK3399PRO SOM based rockpi-n10 target
with below features:
- Custom U-Boot 2020.07-rc4
https://github.com/amarula/u-boot-amarula.git
branch rock-pi
- Linux 5.7.2
- GPT partition layout is being used
- Default packages from buildroot
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
virtio-fs allow sharing a directory between the host and the guest.
It require virtiofsd daemon running before starting Qemu.
The wiki [1] recommand to enable the following kernel options:
CONFIG_VIRTIO
CONFIG_VIRTIO_FS
CONFIG_DAX
CONFIG_FS_DAX
CONFIG_DAX_DRIVER
CONFIG_ZONE_DEVICE
But virtio-fs works fine with only VIRTIO_FS.
Note: ZONE_DEVICE can only be enabled on aarch64 since kernel >= 5.7.
ARCH_ENABLE_MEMORY_HOTREMOVE support is missing for previous kernel [2].
[1] https://virtio-fs.gitlab.io/howto-qemu.html
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=bbd6ec605c0fc286c3f8ce60b4ed44635361d58b
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
>From [1]:
This kernel option allow exporting of the QEMU firmware configuration (fw_cfg)
file entries via sysfs. Entries are found under /sys/firmware/fw_cfg when this
option is enabled and loaded.
Enable the suboption to allow the qemu_fw_cfg device to be initialized via the
kernel command line or using a module parameter.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/drivers/firmware/Kconfig?h=v5.4.42#n187
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This driver is intended to be used by mesa virgl Gallium on the guest.
virtio-gpu is enabled by adding "-device virtio-gpu-pci" on the qemu
command line.
It's detected by lspci and dmesg log:
$ lspci
00:01.0 Display controller: Red Hat, Inc. Virtio GPU (rev 01)
$ dmesg
virtio-pci 0000:00:01.0: enabling device (0000 -> 0002)
[drm] pci: virtio-gpu-pci detected at 0000:00:01.0
[drm] virgl 3d acceleration not supported by host
[drm] EDID support available.
[TTM] Zone kernel: Available graphics memory: 51876 KiB
[TTM] Initializing pool allocator
[TTM] Initializing DMA pool allocator
[drm] number of scanouts: 1
[drm] number of cap sets: 0
[drm] Initialized virtio_gpu 0.1.0 0 for virtio2 on minor 0
The framebuffer interface fb0 is now present in /dev
$ ls /dev/fb*
/dev/fb0
See:
https://www.kraxel.org/blog/2019/09/display-devices-in-qemu/https://at.projects.genivi.org/wiki/display/WIK4/GENIVI+Technical+Summit+Session+Content+2018?preview=%2F28412356%2F28412481%2F2018-10-11_GeniviBangalorTechSummit_Virtio_GPU.pdf
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add the CONFIG_PCI symbol due a change in kernel 5.0 [1].
The option was previously enabled by default (default y).
"PCI: consolidate PCI config entry in drivers/pci
There is no good reason to duplicate the PCI menu in every architecture.
Instead provide a selectable HAVE_PCI symbol that indicates availability
of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the
rest in drivers/pci."
Qemu aarch64 provide a PCIe Host bridge but it require CONFIG_PCI_HOST_GENERIC
enabled in the kernel.
With CONFIG_PCI_HOST_GENERIC enabled PCIe host bridge is detected:
$ dmesg
pci-host-generic 4010000000.pcie: host bridge /pcie@10000000 ranges:
pci-host-generic 4010000000.pcie: IO 0x3eff0000..0x3effffff -> 0x00000000
pci-host-generic 4010000000.pcie: MEM 0x10000000..0x3efeffff -> 0x10000000
pci-host-generic 4010000000.pcie: MEM 0x8000000000..0xffffffffff -> 0x8000000000
pci-host-generic 4010000000.pcie: ECAM at [mem 0x4010000000-0x401fffffff] for [bus 00-ff]
pci-host-generic 4010000000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x10000000-0x3efeffff]
pci_bus 0000:00: root bus resource [mem 0x8000000000-0xffffffffff]
pci 0000:00:00.0: [1b36:0008] type 00 class 0x060000
$ lspci
00:00.0 Host bridge: Red Hat, Inc. QEMU PCIe Host bridge
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=eb01d42a77785ff96b6e66a2a2e7027fc6d78e4a
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Qemu for the aarch64 virt emulate an RTC PL031 device.
Enable the kernel support to allow setting the system time.
"date" now return the current time:
Sun Jul 5 20:38:50 UTC 2020
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
And rebase uboot patch.
Tested-by: Maeva Manuel <maeva.manuel@oss.nxp.com>
[Maeva: Tested on i.MX6Quad SabreAuto CPU1]
Signed-off-by: Julien Olivain <julien.olivain@oss.nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This makes the boot script set appropriate root parameters when it's
loaded from a NAND flash device.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The DCON driver for the platform is a staging driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The XO-1 laptop has a NAND flash and firmware capable of reading JFFS2
from it. Enable JFFS2 kernel support so that we'll be able to create
images capable of booting from the internal flash.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A couple of config symbols were mising that things we enable depend on.
Enable them.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This is the keyboard connected via the SP "security processor" on a
XO-1.75. XO-1 has a regular PC keyboard.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
XO-1 has an internal MTD device.
Also, CONFIG_MTD_SPI_NOR was set twice for XO-1.75. One copy is removed,
one remains.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A few conflicts had to be resolved:
- Version number and hash for mesa3d-headers/mesa3d
- Patches added in qemu, and the qemu version number
- The gnuconfig README.buildroot
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch adds support for the i.MX8M Nano EVK Board [1].
The final boot image is created from uboot and firmware binaries in post
image script board/freescale/common/imx/imx8-bootloader-prepare.sh
Note that this config is based on 4.19.35_1.1.0 ; hence, the kernel
configuration needs host-openssl to build.
[1] https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/evaluation-kit-for-the-i-mx-8m-nano-applications-processor:8MNANOD4-EVK
Signed-off-by: Stephane Viau <stephane.viau@oss.nxp.com>
Reviewed-by: Maeva Manuel <maeva.manuel@oss.nxp.com>
Reviewed-by: Julien Olivain <julien.olivain@oss.nxp.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
For some SoCs (i.e.: i.MX8M Nano for now), the DDR training firmware
in the boot image depends on the type of memory installed on a board
(LPDDR4, DDR4, etc...). The previous patch makes this firmware name
agnostic of the DDR type and uses ddr_fw.bin as a generic name. This
patch makes imx8-bootloader-prepare.sh use this generic name,
independently of the kind board DDR type.
Signed-off-by: Stephane Viau <stephane.viau@oss.nxp.com>
Reviewed-by: Maeva Manuel <maeva.manuel@oss.nxp.com>
Reviewed-by: Julien Olivain <julien.olivain@oss.nxp.com>
Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The default iamge size is 32MiB, which is quite low by today's standards.
Besides, the AArch64 kernels are relatively big, which leaves not much
room, if at all, for users to experiment on the default image.
Increase the vfat size to a more reasonable 64MiB.
Note that users who derive an in-tree defconfig for their own case will
allways hit any arbitarary size we put here, so they will anyway have to
also derive this template for their own use-cases.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Commit b80712a16a ("configs/odroidc2:
remove the defconfig") has removed the odroidc2 defconfig, but left
behind a number of files in board/hardkernel/odroidc2, which are now
unused. Let's remove them.
Signed-off-by: Dagg Stompler <daggs@gmx.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This reverts commit f7a887c368 and
23aee3eac4 since the kernel patch
is not needed as soon as qemu >= 3.1.0 is used with a kernel >=
4.11-rc1.
The qemu emulation of sh-sci driver was fixed by adding basic
timeout handling for 9600 bps [1].
[1] https://git.qemu.org/?p=qemu.git;a=commit;h=71bb4ce1b5592cdc03abc48cdf4ecb15b2db81a0
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The Qemu version present in readme.txt files was needed when
the Buildroot's Qemu defconfig was tested manually using the
qemu-system-<arch> binary already present on the host.
This information is now incorrect since we are using host-qemu
package, currently at 4.2.0 version, to do a runtime test since
0c79350638.
For m68k-q800, we can use the upstream qemu since 4.2.0 release
[1].
So, remove this line from the readme.txt.
[1] https://www.qemu.org/2019/12/13/qemu-4-2-0/
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Linux version are changed to the new LTS kernel 5.4.35 for all qemu
defconfigs, except for riscv and csky. Thoses defconfigs are left
unchanged because they require either a custom Linux repository
or a specific kernel header version causing some difficulties when
upgrading to 5.4.35.
Update the nios2-10m50 linux.fragment to update the .dtb build directory
due to a change in kernel 4.20 [1]:
nios2: build .dtb files in dts directory
Align nios2 with other architectures which build the dtb files in the
same directory as the dts files. This is also in line with most other
build targets which are located in the same directory as the source.
This move will help enable the 'dtbs' target which builds all the dtbs
regardless of kernel config.
This transition could break some scripts if they expect dtb files in
the old location.
For x86 and x86_64 kernel, add the CONFIG_PCI symbol due a change in kernel
5.0 [2]. The option was previously enabled by default (default y).
PCI: consolidate PCI config entry in drivers/pci
There is no good reason to duplicate the PCI menu in every architecture.
Instead provide a selectable HAVE_PCI symbol that indicates availability
of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the
rest in drivers/pci.
Update the kernel of ppc-mac99 defconfig added in Buildroot 2019.08.
This version bump was tested on gitlab [4] using the newly introduced
boot-qemu-image.py script [5].
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=118864869805123bf82d666062542440a0fda5dd
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=eb01d42a77785ff96b6e66a2a2e7027fc6d78e4a
[3] a8fac3fcfc
[4] https://gitlab.com/kubu93/buildroot/pipelines/139819874
[5] 0c79350638
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Convert the patch for microblaze kernel added for kernel 3.14 by
Waldemar to git format.
Note: the Waldemar Sob line is missing in the original patch:
fa27985483
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch add support for the low cost QMTECH XC7Z010 starter kit
board [1].
[1] http://www.chinaqmtech.com/xilinx_zynq_soc
Signed-off-by: Martin Chabot <martin.chabot@gmail.com>
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This adds some instructions on how to build and run images for the OLPC
XO laptops.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A defconfig for the nanopi_neo4 was added in
d1cd9cdf26, but then removed in
8af7b11bd8 because an ARM32 compiler was
needed to build ATF, and this was not supported back then.
Thanks to the addition of package/arm-gnu-a-toolchain/, we can now
re-introduce this defconfig.
Compared to the previous defconfig, the following changes were done:
- enable BR2_TARGET_ARM_TRUSTED_FIRMWARE_NEEDS_ARM32_TOOLCHAIN
- bump kernel to 5.4
- increase default rootfs size to 70M
- use mainline u-boot
- switch to Marek Belisko as maintainer
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
NXP i.MX8MNano based SBC with 1GB of LPDDR4 and 16GB eMMC.
More details on the platform here:
https://boundarydevices.com/product/nitrogen8m-nano/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently the volume-label for the vfat partition is a string with
the following pattern: 5934-861D.
Specify the volume-label as "boot" to make it easier to identify it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This defconfig supports the OLPC XO-1 platform.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
There are muliple generations of OLPC laptops, x86 ones based on
Geode, VIA and ARM based with Marvell Armada. All of boot with
OpenFirmware and share some peripherals.
This patch adds the common files.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The support for MacchiatoBin board in U-Boot and Linux has been
significantly improved in the past years. So it no longer makes much
sense to have a separate build configuration based on older vendor
Linux kernel and U-Boot. This commit drops the configuration based on
vendor kernel and U-Boot and renames the mainline-based defconfig.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently the volume-label for the vfat partition is a string with
the following pattern: 5934-861D.
Specify the volume-label as "boot" to make it easier to identify it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Nanopi R1 board with below features:
- U-Boot 2019.01
- Linux 5.0
- Default packages from buildroot
Configuration files taken from Armbian:
https://github.com/armbian/build/blob/master/patch
Signed-off-by: Davide Viti <zinosat@gmail.com>
[Thomas: move U-Boot config and DT to board/friendlyarm/nanopi-r1/uboot/]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit add a post-image script to be used by each qemu board
defconfig in order to generate start-qemu.sh in BINARIES_DIR. The
start-qemu.sh script can be used by Buildroot user to start Qemu
or by a gitlab CI.
To find the correct qemu command line, we use the second post script
argument which must contain "$(BR2_DEFCONFIG)"
BR2_ROOTFS_POST_SCRIPT_ARGS="$(BR2_DEFCONFIG)"
The post-image script expect something like
"/path/to/qemu_aarch64_virt_defconfig" in BR2_DEFCONFIG.
Doing a basename allow to retrieve the name of the defconfig file that
should match on on the "tag" previously introduced in readme.txt files.
For running in the CI, as well as running from a remote machine (e.g. on
a remote build machine), it is better not to start in graphical mode,
but only with the serial line attached to the terminal. The post-build
script prepares two sets of arguments for each case, graphical or
serial, and stores them in the start-qemu.sh script, which then decodes
which to use, based on an argument on the command line (default is still
graphical)
sh4/sh4eb needs a special handling by adding "-serial stdio -display
none"; others only require "-nographics". Some qemu command lines
already contain "-serial stdio", but that does not play nicely with
"-nographics", we remove that when going serial-only (although this
might seem counter-intuitive).
Finally, we ensure the script uses our qemu-system (if it was built).
Signed-off-by: Romain Naour <romain.naour@smile.fr>
[yann.morin.1998@free.fr:
- drop the knowledge about gitlab-ci, replace with an argument to
pass to start-qemu.sh
- adapt the commit log accordingly
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This commit add the name of the Qemu defconfig file after each
qemu command line in order to retrieve it easily.
Since a readme.txt can be shared between several Qemu defconfig, we
need at least one qemu command line in readme.txt for each defconfig.
For now, ignore the qemu_arm_vexpress_tz_defconfig since it fail to build
due to python script issue [1]. Anyway the arm vexpress boot is tested
with qemu_arm_vexpress_defconfig.
[1] http://lists.busybox.net/pipermail/buildroot/2020-February/273738.html
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
There is no reason to create boot.scr in board/udoo/neo and later
install it in TARGET_DIR/boot, leaving a stale file behind.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
There is no reason to create boot.scr in board/solidrun/mx6cubox and
later install it in TARGET_DIR/boot, leaving a stale file behind.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
There is no reason to create boot.scr at board/wandboard and later
install it at TARGET_DIR/boot, leaving a stale file behind.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The U-boot patch has been upstreamed.
Bump U-boot version and drop the patch.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The WDT workaround patch has been upstreamed.
Bump to the new ATF version and drop the patch.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
NXP i.MX8MMini based SBC with 2GB of LPDDR4 and 8GB eMMC.
More details on the platform here:
https://boundarydevices.com/product/nitrogen8m-mini
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- update outdated website URL
- add missing Nitrogen8M configuration
- reword procedure to make it clear it works for all storages
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- To avoid code duplication and to benefit from support script
improvements like empty target dir.
- Note that currently genimage.sh can't be set in defconfig directly for
i.MX8 targets as the POST_SCRIPT_ARGS is used by
imx8-bootloader-prepare.sh
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux 5.4
U-Boot 2020.01
Arm Trusted Firmware v2.2
Buildroot default packages.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Add support for 8MMini and 8MNano
- Upgrade script now resets by default
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Let's clean up "boards/stmicroelectronics" directory a bit
to have everything in particular directories.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The board support package includes the following components:
- U-Boot 2020.01
- Linux 5.4.26
- Buildroot default packages
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
It will be useful for the upcoming introducing stm32mp157a dk2 board.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Let genimage to match the size of the rootfs image instead.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Instead use generic genimage.sh script.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Commit 3f8ace0028
("board/freescale/common/imx: add support for i.MX8") had its
conflicts incorrectly tweaked when applied to Buildroot. The
ahab-container.img is installed with this name (ahab-container.img) by
the imx-firmware package, and not mx8qm-ahab-container.img or
mx8qx-ahab-container.img.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Julien Olivain <juju@cotds.org>
Tested-by: Julien Olivain <juju@cotds.org>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The current Buildroot defconfigs for qemu_x86 and qemu_x86_64
instantiate a console on tty1, which appears on QEMU's
graphical window. Add a console on the serial port (ttyS0) to
be used later for gitlab testing.
This change is need since the script used for gitlab testing
needs to use a serial output with pexpect.
This change is similar to the one made for raspberrypi [1] to
handle HDMI and serial console:
This requires three changes:
1. have two 'console=' entries in the kernel command line: tty1,
then ttyS0;
2. change BR2_TARGET_GENERIC_GETTY_PORT to "console", so it starts
a getty on the last console= passed to the kernel, ttyS0;
3. add a new getty on tty1 to the generated inittab.
Step 2 is actually obtained by removing BR2_TARGET_GENERIC_GETTY_PORT
entirely from the defconfigs, since "console" is the default value.
Step 3 requires a post-build script since the Buildroot makefiles can
configure only one console.
Note: instead of simply adding a new getty on ttyS0 (which would
work) this patch actually changes BR2_TARGET_GENERIC_GETTY_PORT to
instantiate a console on UART, then adds back tty1 via
post-build.sh. This is done only to avoid the "GENERIC_SERIAL" comment
where we instantiate a console on QEMU graphical window, then
instantiate a really-serial console on another line.
The result is these two inittab lines:
console::respawn:/sbin/getty -L console 0 vt100 # GENERIC_SERIAL
tty1::respawn:/sbin/getty -L tty1 0 vt100 # QEMU graphical window
[1] 20878a1017
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As recently reported to the list:
http://lists.busybox.net/pipermail/buildroot/2020-January/271937.html
The hardcoded rootfs partition size can lead to hard to understand build
failures if more packages are added.
So drop the hardcoded partition size. Genimage will then size the partition
to match the size of the rootfs image (which by default is also 60MB for ext4).
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Now that the metadata_csum ext4 option is disabled, we no longer need
the U-Boot workaround.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Use a post-build script to copy uEnv.txt to BINARIES_DIR, as made for
beaglebone.
Drop the post-image script.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Use the same kernel repository and version as configs/beaglebone
- Rename kernel fragment file
- Update U-Boot to 2019.07
- Select weston and qt5wayland
- Select host-uboot-tools with FIT support, required to create the
images.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The correct syntax that Qt5 understands for display names is
"LVDS1", so fix it accordingly.
Reported-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
In board/freescale/common/imx/imx8-bootloader-prepare.sh, when
invoking mkimage_fit_atf.sh, the U-Boot DTB is passed as parameter, to
be included in the FIT image. This parameter usually comes from
BR2_ROOTFS_POST_SCRIPT_ARGS config option. The variable
BL33=u-boot.bin set in the invocation uses the u-boot image which is
including its embedded DTB. This means the U-Boot DTB is included
twice.
The upstream script mkimage_fit_atf.sh plus its Buildroot patch are
meant to use by default the nodtb variant and use the DTB in a
separate image. See [1] and [2].
The U-Boot default DTB which will be included in u-boot.bin image is
selected with U-Boot CONFIG_DEFAULT_DEVICE_TREE, or DEVICE_TREE
variable when invoking "make". If one of those option is not aligned
to the BR2_ROOTFS_POST_SCRIPT_ARGS config option, it's possible the
two included U-Boot DTBs are different. If such case happens, the
built-in DTB is always used, regardless of the other one, selected
with BR2_ROOTFS_POST_SCRIPT_ARGS.
For example, this case happens for TechNexion Pico Pi i.MX8M and
i.MX8MMini. Since the U-Boot defconfig assumes the nodtb version will
be used, it does not set the default DTB. The u-boot.bin will include
the fsl-imx8mm-evk instead. Including the wrong board DTB breaks the
USB and UMS commands (and possibly others). Since those boards does
not have SD card slots, a recovery serial download is needed at every
update.
This patch make sure that only the separate U-Boot DTB will be
included in the FIT image by using the nodtb variant.
[1] https://source.codeaurora.org/external/imx/imx-mkimage/tree/iMX8M/mkimage_fit_atf.sh?h=rel_imx_4.14.98_2.0.0_ga#n35
[2] https://git.busybox.net/buildroot/tree/package/imx-mkimage/0001-add-support-for-overriding-bl32-and-bl33-not-only-bl.patch?h=2019.11#n42
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since kernel commit a5a56f07c272 ("ARM: imx_v6_v7_defconfig: Select the
coda driver as module") the VPU coda driver is selected as module, so it can
be safely removed from linux_qt5.fragment.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The correct syntax that Qt5 understands for display names is
"HDMI1" and "LVDS1", so fix it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 3468ef16fa
("configs/pc_x86_64_efi: use genimage GPT partition table support")
had a small typo on the path to grub boot.img file: i387-pc instead of
i386-pc, which causes a build failure.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/378314412
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Alexandre PAYEN <alexandre.payen@smile.fr>
Cc: Carlos Santos <casantos@datacom.com.br>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This remove the file boot.cmd to use an extlinux.conf instead.
Signed-off-by: Louis Aussedat <aussedat.louis@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This configuration builds a 64bit image for RaspberryPi 4.
Signed-off-by: Arthur Courtel <arthur.courtel@smile.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The pi3-minuart-bt Device Tree overlay has been renamed to
miniuart-bt, as it is useful/usable for other platforms than the
RPi3. So we use this DT overlay and rename the
--add-pi3-miniuart-bt-overlay option to --add-miniuart-bt-overlay
accordingly.
Signed-off-by: Arthur Courtel <arthur.courtel@smile.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Instead use the generic infrastructure for u-boot scripts and genimage.
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As already done in post-build.sh, to prevent hiding errors.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Let genimage determine rootfs partition size based on the filesystem
image size.
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 68b5b79b2f has set the getty port to the default console but left
"ttyO0" in bootargs, in the U-Boot environment. Use "ttyS0", instead.
Also set loadaddr to 0x82000000 and fdtaddr to 0x88000000, replacing the
values that were valid for the ancient U-Boot and Linux pre-installed on
old boards but cause boot hangs with the current versions.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Thanks to the introduction of GPT partition table support in genimage,
this commit improves the pc_x86_64_efi_defconfig to remove the use of
the custom script creating the image.
Tested in QEMU, not on a physical device.
So:
- revert commit fee29b05bb7db25e37c8a5175ce00dc712554edf[1]
- add GPT support
- tweak shell script to add the correct UUID in genimage config.
[1]: https://git.buildroot.net/buildroot/commit/?id=fee29b05bb7db25e37c8a5175ce00dc712554edf
[2]: https://git.buildroot.net/buildroot/commit/?id=79b8540d624ac4846ba341b1b9691eccacf0bc05
Signed-off-by: Alexandre PAYEN <alexandre.payen@smile.fr>
Cc: Carlos Santos <casantos@datacom.com.br>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[Thomas:
- drop commented code in post-build.sh
- take into account comments made by Carlos Santos in
http://patchwork.ozlabs.org/patch/1143502/]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use the pi3-miniuart-bt device tree overlay (as the 32bit raspberrypi3
defconfig) instead of the enable_uart option.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes reference path "../build/optee_os-" to "./output/build/optee-os-"
as package is optee-os and symbol file here is reached from BR top
dir and assuming output in output/.
Updates GDB tool name to arm-linux-gdb.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This change introduces a Qemu board for an Armv7-A target executing
with OP-TEE secure world services. The target Linux based normal world
embeds the standard minimal filesystem with OP-TEE non-secure components
embedded files from OP-TEE test, examples and benchmark packages.
qemu_arm_vexpress_tz_defconfig differs from qemu_arm_vexpress_defconfig.
Supporting both secure and non-secure worlds on the Arm target mandates
a secure world, here OP-TEE OS, and a bootloader to boot both worlds,
here TF-A (boot/arm-trusted-firmware). Here non-secure Linux kernel is
booted through U-boot
TF-A bootloader (BL1/BL2) => OP-TEE (BL32) => U-boot (BL33).
| Executes as secure | Secure | Execs as Non-secure
| Loads BL32/BL33 in RAM | Jumps to BL33 | Always booted after
| Jumps to BL32 once done | as Non-secure | secure world inits
Vexpress and vexpress-tz defconfigs also differs in that Qemu emulates
a Cortex-A9 in the former and a Cortex-A15 in the later. Cortex-A15
is the Armv7-A CPU used in upstream TF-A and OP-TEE OS packages hence
selected here.
Defconfig adds a fragment to the Linux kernel native configuration to
enable OP-TEE driver support.
Defconfig adds a fragment to the U-Boot native configuration set boot
command, enable semihosting and remove U-Boot persistent environment
storage support.
The defconfig also enables build of the Qemu emulator in case the
system installed Qemu does not yet support CPU TrustZone secure state.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
[Arnout, with the help of Peter: correct spelling mistakes in readme,
fix U-Boot version to 2019.01, download tarball of TF-A instead of git]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
That is useful and needed for upcoming introducing stm32mp157a-dk1 board.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
genimage makes a full copy of the given rootpath to ${GENIMAGE_TMP}/root
so passing TARGET_DIR would be a waste of time and disk space. We don't
rely on genimage to build the rootfs image, just to insert a pre-built
one in the disk image.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Use a post-build script to copy uEnv.txt to BINARIES_DIR, as made for
beagleboneai.
Keep the post-image script because it is still used by beaglebone_qt5.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Change partition name according to the U-Boot requirements.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
QT_QPA_EGLFS_ALWAYS_SET_MODE=1 needs to be exported, otherwise the Qt5
Cinematic demo throws a storm of the following messages:
Could not queue DRM page flip on screen LVDS1 (Invalid argument)
Improve the instructions by mentioning such requirement.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 5facee5cc3 ("configs/solidrun_clearfog_gt_8k: bump versions of
BSP components") broke automatic load of the mv88e6xxx dsa driver. The
kernel configuration makes the driver a module, which is not loaded
automatically at boot. Mark mv88e6xxx dependencies built-it to fix that.
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add basic support for the Libre Computer "La Frite" SBC.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since the bump to the 20190819 snapshot there is now a dedicated dts file
for the rpi0, so use that rather than the rpi-b-plus one:
bd1336d8b6
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes#12816
Commit 42d22f3bdb ({configs/raspberrypi,package/rpi-firmware}: bump
kernel/firmware to 20190819 version) updated the kernel version but failed
to take into consideration that the rpi0w dts file has been renamed:
6f91b5dbfd
Fix it by renaming the dts/dtb file referenced from the kernel build and
genimage.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489410
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489367
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489328
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489329
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489325
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig has been failing to build since we switched the default
gcc version to gcc 8.x, as the Linux kernel version is too old and
doesn't contain the necessary fixes to build with gcc >= 8.x.
Despite several pings to the original submitter of the defconfig
(which is not listed in MAINTAINERS), no fix has been sent, so it is
time to drop this defconfig before the 2019.08 release.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489442
Cc: Patrick Keroulas <patrick.keroulas@savoirfairelinux.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The TS-7680 defconfig does not build with gcc 8.x and 9.x because it
uses an old 3.14 kernel. Technologic Systems, the board manufacturer
recently released an updated 4.9 based kernel on a separate repository
on github.
Bump the kernel release from 3.14.28 to 4.19.186 and update the linux
defconfig name as requested in the TS-7680 documentation [1].
[1] https://wiki.embeddedarm.com/wiki/TS-7680#Linux_4.9.y
Signed-off-by: Julien Grossholtz <julien.grossholtz@openest.io>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit adds a minimal defconfig to build a Buildroot system for
the STM32MP157 Discovery Kit, which is the low-cost evaluation
platform for the new STM32MP157 system-on-chip from ST. This
system-on-chip features a single or dual Cortex-A7, a single
Cortex-M4, and a wide variety of peripherals.
This commit includes a custom linux configuration file, because there
is no specific defconfig for this platform in the kernel, only
multi_v7_defconfig supports it, which is really a massive
defconfig. That's why a custom linux configuration file is added.
A small U-Boot config fragment allows to disable the watchdog, so that
userspace by default doesn't need to have a watchdog daemon running.
The vendor U-Boot and Linux trees are used for the moment, but the
platform support is being upstreamed, so switching to upstream
versions will be possible in the relatively near future.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This is based on the pi3 defconfig. There is currently no 64-bit support
since the upstream kernel does not build in this configuration.
Signed-off-by: Michael Cullen <michael@michaelcullen.name>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch adds support for the HiFive Unleashed board. This includes
building the firmware, kernel and rootFS for the HiFive Unleashed.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
[Thomas:
- fix the directory name hifive_unleased -> hifive-unleashed
- drop from readme.txt the instructions about manually flashing each
partition, since we have a full SD card image
- drop the custom post-image.sh script]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Custom u-boot
Linux v5.1
ATF v2.0
Buildroot default packages
Tested-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1
- Use final 5.1 kernel
- Use default ext2 filesystem]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
u-boot v2019.04
Linux v5.0
Buildroot default packages
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas: use BR2_TARGET_UBOOT_BOOT_SCRIPT to generate the U-Boot
script, instead of doing it in the post-build]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux 5.1
Custom U-Boot
Arm Trusted Firmware v2.0
Buildroot default packages
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use the headers from the kernel, by using
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1=y
- Use the default ext2 rootfs size]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux 5.1
Custom U-Boot
Arm Trusted Firmware v2.0
Buildroot default packages
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use the headers from the kernel, by using
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1=y
- Use the default ext2 rootfs size]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux 5.1
Custom U-Boot
Arm Trusted Firmware v2.0
Buildroot default packages
Tested-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use the headers from the kernel, by using
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1=y
- Use the default ext2 rootfs size]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux v5.2
Custom U-Boot
Arm Trusted Firmware v2.0
Buildroot default packages
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use the kernel headers from the kernel, by using
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_2=y
- Use the final 5.2 kernel instead of rc1.
- Use the default ext2 rootfs size]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The most important change is to use the toolchain compiled by
buildroot itself. We also bump kernel to 5.0 with kernel.org.
Gx6605s' PHYS_OFFSET if 0x10000000 and we make qemu and gx6605s the
same to ease maintaince. This PHYS_OFFSET is also OK for 610 qemu.
In this patch we add gx6605s.dts in board/csky, because linux-5.0
doesn't contain gx6605s.dts in its tree.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Display variant dtbs are no longer part of the linux-at91 tree.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
PowerPC kernel developers were after a userspace for testing 32-bit
powerpc kernels. This machine both suits that requirement and has
support in qemu. It's also a fairly common piece of 32-bit ppc hardware.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Daniel Axtens <dja@axtens.net>
[Peter: lock kernel/headers to 5.2.4]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to 2019.07 and kernel to version 5.1.16.
Also
- adjust the U-Boot binary name after DM conversion.
- add missing notes about DFU
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Also
- adjust the U-Boot binary name after DM conversion.
- add missing notes about flashing U-Boot and SPL
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
For boards like imx7d-pico, u-boot.img changes to u-boot-dtb.img in
U-Boot v2019.07. Therefore, we need to pick u-boot.img or u-boot-dtb.img
depending on the board configuration.
Just like was done in commit 52344e556f for the generic genimage
template, replace the U-Boot file name with UBOOTBIN, which is set
according to the BR2_TARGET_UBOOT_FORMAT_* option. We also need to set
the correct value for this variable for the u-boot.img and
u-boot-dtb.img cases.
While we're at it, rename the partition from 'u-boot-img' to 'u-boot',
to stay consistent with the generic genimage template.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
[Arnout: correct u-boot.img condition, rework commit log]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
On my machine, it happens once in a while that the virtualised machine
boots too fast for the rootfs to be available at the time the kernel
tries to mount it.
For example, board/qemu/arm-vexpress/readme.txt suggested changing
"-smp 1" up to "-smp 4". But doing so here causes a kernel panic:
VFS: Cannot open root device "mmcblk0" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
1f00 131072 mtdblock0
(driver?)
1f01 32768 mtdblock1
(driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(0,0)
So, add the oh-so-useful 'rootwait' option to all kernel command lines
for qemu defconfigs.
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Mark Corbin <mark.corbin@embecosm.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump Linux and U-Boot versions.
The Linux configuration file and patches are no longer needed.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
[Thomas: also use a tarball for U-Boot.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the 32-bit defconfig to use the latest kernel. This requires a
patch to revert a ABI to ensure that the glibc port continues to work.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for the SolidRun Armada 8040 based Clearfog GT-8K. This
board has the same processor as the Macchiatobin, so we can reuse the
Macchiatobin U-Boot and image definitions.
The kernel fragment enables drivers that are necessary to make
networking ports work (SFP, Ethernet port, and Ethernet switch).
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump Linux to 5.1 and U-Boot to version 2019.01.
U-Boot patch is no longer needed, applied upstream.
U-Boot defconfig name for this board has changed to pico-pi-imx7d.
U-Boot now supports distrobootcmd for this board, so add the appropriate
extlinux.conf and use SPL+u-boot.img instead of u-boot.imx. Note that
the common freescale post-image script handles things appropriately
based on the selected options in .config.
dosfstools and mtools are no longer needed to build the image.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
[Arnout: remove BR2_PACKAGE_HOST_DOSFSTOOLS and BR2_PACKAGE_HOST_MTOOLS]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Modern U-Boot assumes a layout where the first partition is an ext2 and
the kernel and dtb can be found in /boot. In other words, a layout
without boot partition.
Add a genimage.cfg template for the freescale defconfigs with such a
layout.
For now, only the layout with SPL+u-boot.img is added. It's unlikely that
the u-boot.imx approach will be used.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
For the boot image creation for the i.MX8MM, the main differences with
i.MX8M are that there is no HDMI firmware image passed, and the ATF
load address is different.
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Following commit fee29b05bb
("configs/pc_x86_64_efi: use a GPT partition table"),
board/pc/grub-efi.cfg is no longer used anywhere: the
post-image-efi-gpt.sh script generates the grub configuration.
Also, since post-image-efi-gpt.sh generates a grub configuration file
that uses the root filesystem partition UUID as the root= kernel
argument, the instructions in the readme.txt file to tweak root= from
/dev/sda2 to /dev/vda2 is no longer relevant. This was noted in the
commit log of fee29b05bb:
The root filesystem location is passed to the kernel by a partition
UUID, so it is possible to boot on QEMU, directly from the disk image,
or dump the image to a physical device.
Fixes: #11841
Cc: Pete Morici <pmorici@dev295.com>
Cc: Carlos A. M. dos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Very similar to orangepi-zero, except that the board has a 16MB SPI flash, a
2nd ethernet port is provided through a Realtek RTL8152 and wifi is provided
through a Realtek RTL8189FTV (no mainline driver, not supported).
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Default value of CONFIG_SYS_BOOTM_LEN in u-boot causes board reset for
large uImage files, so add u-boot patch to increase the maximum kernel
image size.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The readme.txt would contain similar content for either processor
family, so this patch consolidates the usage and adds the new
T2080 notes.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add Andes 32-bit defconfig for AE3XX platform.
Signed-off-by: Che-Wei Chuang <cnoize@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
Signed-off-by: Nylon Chen <nylon7@andestech.com>
[Thomas:
- fix commit title to match the defconfig name
- use the external toolchain package]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Default value of CONFIG_SYS_BOOTM_LEN in u-boot causes board reset for
large uImage files, so add u-boot patch to increase the maximum kernel
image size.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch enables the inclusion of the Pi's overlays. Previously
the overlays were not included in the genimage configuration.
This patch ensures overlays are included in the sdcard (when
enabled) by defaulting to the inclusion of an empty
output/images/rpi-firmware/overlays directory in genimage cfg.
The Pi's overlays are built with the following config
variables:
BR2_PACKAGE_RPI_FIRMWARE=y
BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTBS=y
BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS=y
BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
BR2_LINUX_KERNEL_IMAGE_NAME="Image"
BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="Image modules dtbs"
After building, the dtbo files are present in the
output/images/rpi-firmware/overlays directory but not added
to the sdcard because they are missing from the genimage cfg
file.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
[Arnout: fix indentation, and add comment explaining why an empty
directory is created.]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This bumps to linux/linux-headers 5.0 and u-boot version 2019.01. The
kernel patch is no longer needed, as the Device Tree for the platform
is now upstream.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use OpenSBI by default instead of riscv-pk (BBL).
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reduce the config fragment to the bare minimum to enable 32-bit
support. This means we are as close as possible to the arch
defconfig.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Convert the config to the arch defconfig plus a fragment. When this
fragment is applied we will generate the same config as we previously
did.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The old 3.4 Linux kernel used by this defconfig doesn't build with gcc
7.x.
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The update of imx-mkimage in commit
c14d92d439
broke the imx8-bootloader-prepare.sh script for i.MX8M, used in
freescale_imx8mqevk_defconfig
The updated mkimage_fit_atf.sh script in imx-mkimage now needs
a ATF_LOAD_ADDR variable, which was set to 0x00910000 for i.MX8M.
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This defconfig was added in October 2016 and was never updated since
then. It currently fails to build because U-Boot is too old and
doesn't build with host-openssl in version 1.1.x.
On February 13, 2019, the original submitter was notified, but didn't
reply, so let's remove the defconfig for this platform.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/165766194
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Linux version are changed to 4.19.16 (LTS) for all qemu defconfigs,
except for riscv. riscv defconfigs are left unchanged because they have
a custom Linux repository causing more difficulties when upgrading to
4.19 for riscv32. And for the riscv64, it has been updated recently to
Linux 4.20 by another contributor.
Patch for arm-versatile-nommu is changed into a git format
Add cache attributes for xtensa-lx60-nommu config because the commit
7bb516ca54
added a new config variable for memory cache attribute:
CONFIG_MEMMAP_CACHEATTR
All these updated configs have been built successfully.
Signed-off-by: Gerome Burlats <gerome.burlats@smile.fr>
Cc: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Configuration contains:
- building tpl, spl and u-boot (forked u-boot repository)
- booting from SD card and network via PXE
- working ethernet, usb and uart
- minimal rootfs with busybox
- ready to flash SD card image
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since all EFI-based systems support GPT, this commit changes
pc_x86_64_efi to use a GPT partition table. It shows an example of how
to craft a disk image with GPT partitioning instead of MBR. This is
achieved by means of a post-image script which uses
mkdosfs+mcopy+sfdisk, since genimage is unable to deal with GPT. Long
term, it would be ideal if genimage had GPT support, but until then,
this script shows how to achieve creating a GPT-based disk image.
The script was kept as simple as possible to make it easy to understand
and adapt for other purposes.
The root filesystem location is passed to the kernel by a partition
UUID, so it is possible to boot on QEMU, directly from the disk image,
or dump the image to a physical device.
Signed-off-by: Carlos Santos <casantos@datacom.com.br>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
qemu_aarch64_virt_defconfig (implicitly) specifies cortex-a53, so adjust the
QEMU command line to also emulate a a53 instead of a57.
Also adjust the defconfig to explicitly specify a53 for consistency/clarity.
Signed-off-by: Gerome Burlats <gerome.burlats@smile.fr>
Cc: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Since riscv64 works with linux default defconfig, this patch drop custom config.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
Tested-by: Mark Corbin <mark.corbin@embecosm.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot and kernel to their latest releases.
Remove the documented limitations. Recent kernels added support for the
SOM SPI flash, and the carrier SFP port.
Mention the 'dd' command in the warning text. No script is involved.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Before this commit, the grub configuration file was copied to the
TARGET_DIR in a post-image hook, after the filesystem has been
generated. It was kinda working because the board/pc's grub
configuration and the default one are the same and the later was
copied during the build process of the grub2 package.
This commit ensures the custom board/pc grub configuration is copied at
the right time.
Signed-off-by: Grégoire Delattre <gregoire.delattre@gmail.com>
Reviewed-by: Matt Weber <matthew.weber@rockwellcollin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This updates LEGO MINDSTORMS EV3 to Linux kernel 4.19 and U-Boot
2018.11. This kernel brings Bluetooth support, so some Bluez packages
are also added. Also, we now have proper device tree support, so a few
things are rearranged in the flash and SD card images since the DTB is
no longer appended to the kernel image.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The first stage bootloader on LEGO MINDSTORMS EV3 only loads the first
256K of the flash memory (this is hard-coded in an EEPROM). So, the
second stage bootloader (U-Boot) cannot exceed this size.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
NXP U-Boot tree has the following build issue:
MKIMAGE u-boot-dtb.imx
Error: No BOOT_FROM tag in board/freescale/mx7dsabresd/imximage.cfg.cfgtmp
arch/arm/imx-common/Makefile:91: recipe for target 'u-boot-dtb.imx' failed
make[2]: *** [u-boot-dtb.imx] Error 1
Makefile:877: recipe for target 'u-boot-dtb.imx' failed
This issue has been fixed by commit f916757300c1 ("imx: Create
distinct pre-processed mkimage config files"), so backport this
commit to the NXP U-Boot tree in order to fix the build error.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/136980027
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch updates the csky custom external toolchain to fix a broken
host dependency of gdb on libexpat.so.0 (most hosts now ship
libexpat.so.1). gdb is required to copy and and boot the kernel (see
board/csky/readme.txt). The updated gdb no longer has this host
dependency, which solves the issue.
Since this external toolchain was built and tested with csky kernel
4.9.56, this patch also updates to that kernel version.
Finally, this 4.9.56 csky kernel changed its default bootargs. So we
add a patch to preserve the same behavior as the previous version.
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Orangepi lite2 board has AP6356S WiFi/BT combo, but does
not have ethernet port. So it makes sense to enable wireless
networking by default:
- add broadcom wireless firmware package to image
- add basic wireless tools to image
- add rootfs overlay with proper NVRAM file for on-board AP6356S chip
- add mdev to image to enable module autoloading
- update readme.txt to test wifi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Orangepi Lite2 board with below features:
- U-Boot 2018.09
- Linux 4.19.0-rc8
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Orangepi One Plus board with below features:
- U-Boot 2018.09
- Linux 4.19.0-rc8
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently, U-Boot is failing to build, due to some issues
with the toolchain and the U-Boot port.
Fix it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
New generic defconfig for aarch64, to run on aarch64 servers compliant
with EFI firmware and ACPI.
This can also be tested with qemu, and is useful so that we have an
arm defconfig with grub enabled. Tested with qemu 2.11.2 and AAVMF,
the aarch64 virtual machine UEFI firmware.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
[Thomas: extend readme.txt with more details]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
4.18 brought cpufreq support for H3, but sunxi_defconfig does not enable the
ondemand cpufreq govenor so the frequency is dynamically adjusted - So
enable it in linux-extra.config.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
4.18 brought cpufreq support for H3, but sunxi_defconfig does not enable the
driver for the sy8106a regulator used on the board or enable the ondemand
cpufreq govenor so the frequency is dynamically adjusted - So enable these in
linux.fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The default ORC unwinder requires libelf to be built. While we could
build libelf using BR2_LINUX_KERNEL_NEEDS_HOST_LIBELF, we probably
don't really need the ORC unwinder in the PC defconfigs, so let's use
the frame pointer unwinder instead.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/123771107
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the kernel and U-Boot versions to the actual versions in use.
Update the description of supported hardware features.
Add a note that the stale SPI flash environment issue only affects the
vendor BSP.
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to version 2018.11. This version supports autodetection of
SD/eMMC boot source, so we can now enable environment load from SD card.
Add a U-Boot kconfig fragment that sets SD/eMMC as environment load/save
device. This avoids stale environment values from the SPI flash. That in
turn, allows to use the more convenient distro boot which is enabled in
the default environment.
Bump kernel to version 4.19.2. This version enables
CONFIG_PHY_MVEBU_CP110_COMPHY in the arm64 defconfig, so remove it from
the kernel kconfig fragment. Enable support for SFP modules detection
and configuration. Leave the PHY drivers for now to keep them built into
the kernel. The kernel defconfig builds these drivers as modules. But
that does not work as expected in the default configuration.
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Amarula A64-Relic board has AP6330 WiFi/BT combo, but does
not have ethernet port. So it makes sense to enable wireless
networking by default:
- add broadcom wireless firmware package to image
- add basic wireless tools to image
- add rootfs overlay with proper NVRAM file for on-board AP6330 chip
- add mdev to image to enable module autoloading
- update readme.txt to test wifi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Amarula A64-Relic board
with below features:
- U-Boot 2018.07
- Linux 4.17.0-rc6
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas: add missing BR2_TARGET_UBOOT_NEEDS_PYLIBFDT=y and
BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y options.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Some ZynqMP device trees in the kernel have a dot in their name,
for example "zynqmp-zcu102-rev1.0". The post image script
left out the part after the dot and created an invalid symlink.
Signed-off-by: Francois Beerten <fbeerten.git@colabti.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch provides support for the board Odroid XU4. It uses a recent
4.14 kernel released by Hardkernel, and the current u-boot 2017.05
also from Hardkernel.
Signed-off-by: Pierre CROKAERT <pct@crookies.net>
[Thomas:
- Update DEVELOPERS file
- Update .gitlab-ci.yml file
- Simplify the boot.ini script
- Add missing BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_14 option
- Add BR2_PACKAGE_HOST_DOSFSTOOLS and BR2_PACKAGE_HOST_MTOOLS since a
VFAT filesystem is generated
- Keep the default root filesystem size, since it is sufficient.
- Reduce the size of the VFAT filesystem]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add intial support for Bananapi M2 Ultra board based on the Allwinner
R40 SoC.
- U-Boot 2018.07
- Linux 4.18.12
Board specifications: http://www.banana-pi.org/m2u.html
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add RISC-V 64-bit defconfig for QEMU virt machine.
Tested with QEMU 2.12.1
Signed-off-by: Mark Corbin <mark.corbin@embecosm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit renames olimex_a20_olinuxino_lime_mali to
olimex_a20_olinuxino_lime_legacy, because the upstream Linux kernel
now also supports using the Mali GPU.
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch removes duplicate messages in Linux log on HSDK board.
For HSDK board we setup bootargs via device tree,
see https://elixir.bootlin.com/linux/latest/source/arch/arc/boot/dts/hsdk.dts#L25
"console=ttyS3" was mistakenly placed in u-boot bootargs which are
appended to Kernel bootargs in case of using buildin .dtb.
Before patch log is like:
------------------------8<-------------------------------------
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz,...
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz,...
mmc0: new SDHC card at address 59b4
mmc0: new SDHC card at address 59b4
blk_queue_max_segment_size: set to minimum 8192
blk_queue_max_segment_size: set to minimum 8192
------------------------>8-------------------------------------
After patch log is like:
------------------------8<-------------------------------------
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz,...
mmc0: new SDHC card at address 59b4
blk_queue_max_segment_size: set to minimum 8192
------------------------8<-------------------------------------
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Resurrect support for RIoTboard after 2018.02.x deprecation.
Signed-off-by: Nikolay Dimitrov <nikolay.dimitrov@retrohub.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
At first the support for i.MX8MQ processors was minimal, hence this
section in the readme file.
Since then, GPU support was added [1] in master and VPU in next [2].
So drop this section as it is confusing people and no one maintains it.
[1] https://git.buildroot.net/buildroot/commit/?id=84afda9c
[2] https://git.buildroot.net/buildroot/commit/?id=82732071
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
512B is not a correct size to express "512 bytes", and causes a
genimage failure:
ERROR: Invalid size suffix 'B' in '512B'
To express "512 bytes", using just "512" is sufficient. With this
commit, genimage works fine, and we indeed have a 512 bytes unused
partition:
$ fdisk -l output/images/sdcard.img
Disk output/images/sdcard.img: 60 MiB, 62915584 bytes, 122882 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x00000000
Device Boot Start End Sectors Size Id Type
output/images/sdcard.img1 1 1 1 512B 0 Empty
output/images/sdcard.img2 2 524289 524288 256M 83 Linux
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/88314963
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
As for sh4-r2d (little-endian) restore the old sh-sci driver behaviour
for sh4eb-r2d.
Tested with qemu_sh4eb_r2d_defconfig.
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This reverts commit 18e8cf159177100e69d528293f8cf6875c0b1bca (kernel)
The last Qemu kernel update [1] introduced a regresion in sh4 SCIF
serial device. Some keyboard presses are very slow to be taken into
account, perhaps not even taken into account at all. This would
explain why our test infrastructure doesn’t manage to login as root
[2][3][4].
git bisect reported a kernel patch from 4.11, increasing RX FIFO
trigger defaults value for sh-sci (H)SCIF. The kernel patch itself
looks good but the Qemu emulation is not ready to handle this new
setting.
>From Qemu (2.12.0): target/sh4/README.sh4
"Configuration of the second serial port (SCIF) is supported. FIFO
handling infrastructure has been started but is not completed yet."
We can't use the first serial port (ttySC0) because it's the second
SH UART that's emulated by Qemu.
In order to be able to test sh4 architecture with newer kernel,
revert to the old behaviour.
[1] 03fb00f217
[2] https://gitlab.com/free-electrons/toolchains-builder/-/jobs/72006425
[3] https://gitlab.com/free-electrons/toolchains-builder/-/jobs/72006427
[4] https://gitlab.com/free-electrons/toolchains-builder/-/jobs/72006426
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
U-Boot SPL configures pinmuxes, clocks and other low-level devices. On
the Xilinx ZynqMP SoCs the code to do this resides in a file called
psu_init_gpl.c which is initially generated by the Xilinx development
tools. Add an option to pass these files from the outside (e.g. in the
board files).
For this to work properly, a patch to U-Boot is needed. However this
patch must be applied by each defconfig using
BR2_TARGET_UBOOT_ZYNQMP_PSU_INIT_DIR. If it were in boot/uboot/ to be
applied unconditionally, it would break the build for configs using a
U-Boot version where the patch is already applied.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Reviewed-by: Joel Carlson <JoelsonCarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
[Thomas: add comment about U-Boot version requirements to use this
option.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This adds support the Xilinx ZCU106 development board.
[Tested on the ES2 (Engineering Sample 2) version of the board]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
In order to boot on the Xilinx ZynqMP SoCs, U-Boot SPL requires a
recent PMU firmware loaded. Instruct U-Boot to add pmufw.bin to the
boot.bin file together with U-Boot SPL, and the boot ROM will load
both.
For this to work properly, a patch to U-Boot is needed. However this
patch must be applied by each defconfig that wishes to use
BR2_TARGET_UBOOT_ZYNQMP_PMUFW. If it were in boot/uboot/ to be applied
unconditionally, it would break the build for configs using a U-Boot
version higher than 2018.7-rc1 where the patch is already applied.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Reviewed-by: Joel Carlson <JoelsonCarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
[Thomas:
- indicate that this feature requires U-Boot 2018.07, since commit
c7df098a71e05dc81cee818747759e8060b59626 is needed.
- define UBOOT_ZYNQMP_KCONFIG_PMUFW only once, and instead use a
variable named UBOOT_ZYNQMP_PMUFW_PATH to store the path to the PMU
firmware]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Use proper ARCH for mkimage command
- Use different U-Boot binary name depending on ARCH
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
6x_bootscript/6x_upgrade have been deprecated for more than a year.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The upgrade.cmd script expects the binary to be named
u-boot.<uboot_defconfig>.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Allow user to override the hardcoded dtb name by using
BR2_ROOTFS_POST_SCRIPT_ARGS.
The only user of this script, configs/freescale_imx8mqevk, is updated
accordingly.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for flashing the u-boot-dtb.imx binary in the SD card
when a target selects BR2_TARGET_UBOOT_FORMAT_DTB_IMX.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The 2017 MinnowBoard Turbot skews no longer use the Realtek 8169
Ethernet chip. The Turbot D0 uses The Intel I211, the Turbot Dual
Ethernet has an I210 (quad-core) or I211 (dual-core).
Add CONFIG_IGB to the Linux config but keep the Realtek 8169 support
to avoid breaking older boards
Tested on Turbot D0, lspci -k shows the igb driver is used:
03:00.0 Class 0200: 8086:1539 igb
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add a defconfig for the Olimex A10-OLinuXino-LIME, reusing most
of the A20-OLinuXino-Lime and A13-OLinuXino files (sym links).
The configurations for Olimex A10-OLinuXino-LIME feature:
- U-Boot 2018.03
- Mainline Linux kernel 4.14.26
Signed-off-by: Leon Anavi <leon.anavi@konsulko.com>
[Arnout: remove commented-out BR2_ARM_EABIHF=y (which is default)]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
As per latest Raspberry Pi firmware documentation, the option
'arm_control' has been deprecated in favor of 'arm_64bit'.
Fixes https://bugs.busybox.net/show_bug.cgi?id=11111.
Signed-off-by: Jason Tang <tang@jtang.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the kernel version to 4.17.2.
Update U-Boot version to 2018.05.
Migrate to U-Boot generic distro configuration which is easier than the
hand written boot script.
Improve the 'dd' command example in readme.txt.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
To not maintain custom copy of inittab file lets adopt approach
used in raspberrypi adding post-build script for synopsys/axs10x
boards.
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Apply modifications made in recent commits:
- 456ea9871e busybox: add /dev/std{in, out, err} symlinks to inittab
- 13dbe73782 busybox: reduce number of mkdir calls in inittab
- 8a89d290d4 busybox: add an inittab entry to activate swap
Signed-off-by: Carlos Santos <casantos@datacom.com.br>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
4.17 brings support for HDMI out, but sunxi_defconfig hasn't been updated to
enable the drivers - So add a kernel fragment to enable them.
Likewise, analog audio has been supported since 4.10, but the driver isn't
enabled in sunxi_defconfig, so enable it in the fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump kernel to version 4.17 and U-Boot to 2018.05.
As the dtb file has been renamed in mainline, make the necessary
adjustments in U-Boot environment and also in
BR2_LINUX_KERNEL_INTREE_DTS_NAME.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump kernel to version 4.17 and U-Boot to 2018.05.
As the imx_v6_v7_defconfig in 4.17 already selects the
CONFIG_CFG80211_WEXT option, the linux.fragment can
be simply removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump linux as well headers to v4.16 version, this eventually drop the
wifi patch since it has been merged to Linux v4.16.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
All linux configs are renamed to a version neutral filename
to avoid further renaming on kernel bumps.
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.16.7 2.12.0 YES OK
arm_versatile 4.16.7 2.12.0 YES OK
arm_versatile_nommu 4.16.7 2.12.0 YES OK (3)
arm_vexpress 4.16.7 2.12.0 YES OK
m68k_mcf5208 4.16.7 2.12.0 YES OK
m68k_q800 4.16.7 q800-v2.11.0 NO (2) OK
microblazebe 4.16.7 2.12.0 YES OK
microblazeel 4.16.7 2.12.0 YES OK
mips32r2el_malta 4.16.7 2.12.0 YES OK
mips32r2_malta 4.16.7 2.12.0 YES OK
mips32r6el_malta 4.16.7 2.12.0 YES OK
mips32r6_malta 4.16.7 2.12.0 YES OK
mips64el_malta 4.16.7 2.12.0 YES OK
mips64_malta 4.16.7 2.12.0 YES OK
mips64r6el_malta 4.16.7 2.12.0 YES OK
mips64r6_malta 4.16.7 2.12.0 YES OK
nios2-10m50 4.16.7 2.12.0 NO OK
or1k 4.16.7 2.12.0 NO OK
ppc_g3beige 4.16.7 2.12.0 YES OK
ppc_mpc8544ds 4.16.7 2.12.0 YES OK
ppc_virtex_ml507 4.16.7 2.12.0 NO OK
ppc64_pseries 4.16.7 2.12.0 YES OK
ppc64le_pseries 4.16.7 2.12.0 YES OK
ppc64_e5500 4.16.7 2.12.0 YES OK
sh4 4.16.7 2.12.0 YES OK
sh4eb 4.16.7 2.12.0 NO (1) OK
sparc_ss10 4.16.7 2.12.0 YES OK
sparc64_sun4u 4.16.7 2.12.0 YES OK
x86 4.16.7 2.12.0 YES OK
x86_64 4.16.7 2.12.0 YES OK
xtensa_lx60 4.16.7 2.12.0 YES OK
xtensa_lx60_nommu 4.16.7 2.12.0 YES OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Kernel patch required, switched to devicetree usage
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
RK3288 Vyasa board support falcon mode in U-Boot and SD layout start from
16MB offset for args and 17MB for uImage. So give full u-boot partition
space as 30M so-that it can occupy bigger uImage file and doesn't overlap
rootfs partition.
[Peter: use # as comment character, clarify comment wording]
Reported-by: Shyam Saini <shyam@amarulasolutions.com>
Tested-by: Shyam Saini <shyam@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shyam saini <shyam@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The kernel now includes the rpi3b+ device tree for aarch64
Signed-off-by: Martin Bark <martin@barkynet.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With this commit we update u-boot version to 2018.05 for
Synopsys boards. U-boot version 2018.05 was released recently
and includes significant changes for ARC boards:
* Fix for compile-time warning for AXS10x
* Add support of platform-specific commands for HSDK
* Add support for on-board SPI flash on HSDK
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use "i.MX8MQ" (in capital letters) for the SoC name for better
readability.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Improve the documentation by adding the configuration of SW801 and SW802
switches for SD card boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently this target fails to build:
arch/arm/mach-imx/built-in.o: In function `init_mmdc_lpddr2_settings':
platform-spi_imx.c:(.text+0x8f18): undefined reference to `imx6sll_lpddr2_freq_change'
arch/arm/mach-imx/built-in.o: In function `imx6ul_cpuidle_init':
platform-spi_imx.c:(.init.text+0x195c): undefined reference to `mx6ull_lpm_wfi_end'
platform-spi_imx.c:(.init.text+0x1960): undefined reference to `mx6ull_lpm_wfi_start'
platform-spi_imx.c:(.init.text+0x1964): undefined reference to `imx6ull_low_power_idle'
arch/arm/mach-imx/built-in.o: In function `imx6sl_init_late':
platform-spi_imx.c:(.init.text+0x56f0): undefined reference to `imx6sll_cpuidle_init'
Makefile:969: recipe for target 'vmlinux' failed
NXP 4.9 kernel does not properly support mx31, so better remove this target.
mx31_3stack board is currently supported in U-Boot and kernel mainline,
so if someone is interested on this board, then a target can be introduced
later which uses these mainline components.
Currently I do not have access to this board, so remove it its defconfig
for now.
Fixes: https://gitlab.com/buildroot.org/buildroot/-/jobs/66561688
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As we are about to remove the Blackfin architecture, remove the only
defconfig that was using this CPU architecture.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit adds a genimage template file that is used for i.MX8
platforms in the common i.MX post-image script.
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit adds an imx8-bootloader-prepare.sh script that will be
used by i.MX8 platforms to prepare their bootloader image.
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit makes the common post-image.sh script used by Freescale
platforms compatible with arm64:
- Support having DTBs in sub-folders
- Support a kernel image in the 'Image' format
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adds support for the at91sam9g20-ek board to the flasher.sh script.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support to the flasher.sh script for the at91sam9260-ek board which
complements the existing at91sam9260eknf_defconfig.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Instead of using the install of sam-ba under host/opt directly, use the symlink
created in host/bin. The side effect of doing this instead allows the correct
sam-ba binary to be used based on the host arch being 32 bit or 64 bit.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Resolves an error in the way the bootlin toolchain-builder uses
the board/qemu/ppc64-e5500/readme.txt to generate the qemu test
command.
https://github.com/free-electrons/toolchains-builder/blob/master/build.sh#L186
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Switch to Linux kernel version 4.9.59 from the TI SDK 04.02.00.09
(TI SDK release date: 23.12.2017)
Updated uboot to version 2018.01
uEnv.txt corrected to boot from sd card on the ti-am335x-evm
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adding basic support modeled after the Freescale/NXP T1040RDBD4 board.
This target is used to support testing of the bootlin e5500 toolchain.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
[Thomas: update .gitlab-ci.yml.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
My goal was to rely on upstreamed features as much as possible, which
means that some bits are only half-baked for now:
- Due to the DTS restructuring in upstream kernel, we require 4.11+. The
latest LTS or CIP kernels do not know about the -Base model.
- Linux has no generic support for SFP cages (yet). It seems that this
has hit the net-next tree in August 2017, but there's been no release
(it's probably targettting 4.14). Also, the merge only included the
required infrastructure; the mvneta driver conversion is not included.
Patches which finalize this exist in Russel King's tree and also in
random vendor trees.
- There's no access to the SPI flash in these versions of
uboot/linux/dts.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
[Arnout:
- rename to solidrun_clearfog_defconfig;
- specify kernel headers version (default is now 4.15);
- remove ext2 fs size override, the 4 extra MB are not needed;
- U-Boot needs dtc and openssl;
- add comments to defconfig;
- update .gitlab-ci.yml;
- mention in readme.txt that SFP support is missing;
- add Jan to DEVELOPERS.
]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Synopsys DesignWare HSDK (which stands for ARC HS
Development Kit) is the latest and greatest development
platform that sports quad-core ARC HS38 in real silicon.
Most noticeable features of the board are:
* Quad-core ARC HS38 CPU running at 1GHz
* 4Gb of DDR
* Built-in Vivante GPU (well supported via open source
Etnaviv drivers)
* Built-in Wi-Fi/Bluetooth module (RedPine RS-9113)
And as usual we have:
* [micro] SD-card slot
* 2 USB 2.0 ports
* 1Gbit Ethernet port
* Built-in Digilent JTAG probe
* Serial port accessible via micro-USB port
Writing sdcard.img on SDcard creates two partitions:
* FAT32 with uImage and uboot.env
* EXT4 with root filesystem
We modify kernel config because in default hsdk kernel config
CONFIG_INITRAMFS_SOURCE parameter is set and when we build
rootfs separately (BR2_TARGET_ROOTFS_INITRAMFS is not set)
error appears. Also we set up CONFIG_ARC_UBOOT_SUPPORT which
enables usage of uboot variables in the boot process.
[Peter: Fix comments and rename defconfig to snps_archs38_hsdk_defconfig,
Add defconfig to DEVELOPERS and fixup board/synopsys entry,
Drop postimage script, rename env file in genimage.cfg and drop size
setting for rootfs partition,
Add "" for CONFIG_INITRAMFS_SOURCE in linux fragment]
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-buildroot@synopsys.com
Reviewed-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Up to now, Raspberry Pi Zero W (rpi0w) could be built with the normal
raspberrypi0_defconfig. However, then you don't have support for the
Bluetooth out-of-the-box, which makes using a W a bit pointless.
Therefore, create a separate defconfig for the W. It is a copy of
raspberrypi0_defconfig with the following changes:
- Add DT overlays (from rpi-firmware) to support Bluetooth.
- Pass --add-pi3-miniuart-bt-overlay to post-image.sh.
Since there is now a separate raspberrypi0w_defconfig, the W support
can be removed from raspberrypi0_defconfig.
Signed-off-by: Yves Deweerdt <yves.deweerdt.linux@gmail.com>
[Arnout:
- Bump to same kernel version as raspberrypi0.
- Remove redundant comment.
- Remove redundant default BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS=y.
- Improve commit log.
- Refresh .gitlab-ci.yml.
]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
The uCLS1012A-SOM product family (ucls1012a) is an Arcturus Networks Inc.
64bit ARM Cortex-A53 class System on Module powered by a NXP QorIQ LS1012A
Low Power Communication Processor. This 314 pin MXM3.0/SMARC module card
contains DDR3, QSPI NOR Flash, eMMC NAND Flash, optional Audio CODEC and is
available with 1 or 2 Gig-Ethernet PHYs.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Changes v1 -> v2:
- updated kernel and u-boot source repositories to github
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Sometimes imximage throws the following error:
MKIMAGE u-boot-dtb.imx
Error: No BOOT_FROM tag in board/freescale/mx6sxsabresd/imximage.cfg.cfgtmp
arch/arm/imx-common/Makefile:91: recipe for target 'u-boot-dtb.imx' failed
Later on, when running mkimage for the u-boot.imx it will succeed in
finding the IVT offset.
Looks like some race condition happening during parallel build when
processing mkimage for u-boot-dtb.imx and u-boot.imx.
A proper fix still needs to be implemented, but as a workaround let's
remove the error when the IVT offset is not found.
It is useful to have such message, especially during bring-up phase,
but the build error that it causes is severe, so better avoid the
build error for now.
The error checking can be re-implemented later when we have a proper
fix.
This workaround has already been applied in mainline U-Boot:
http://git.denx.de/?p=u-boot.git;a=commit;h=b5b0e4e351e20a606de22db6a56ad6bc1e2aa8fd
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/59015347
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The T1 QoriQ from NXP has had a few varients of RDB dev boards.
This target is against the latest D4RDB version. Any of the
other versions before D4RDB (plain RDB), may require backing off
the uboot version to SDK 1.6 and/or adjusting the kernel dtb used.
This board configuration provides an upstream kernel build which
has been verified to boot on target.
The target assumes the user still uses the NXP suggested prebuilts
in the SDK2.0 (last release for PowerPC). If a uboot rebuild is
required, the source for SDK2.0 can be found in the following repo.
http://git.freescale.com/git/cgit.cgi/ppc/sdk/u-boot.git/tag/?id=fsl-sdk-v2.0-1703
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Replacing the p1010rdb, this board is based on the tower development
system still available by NXP. The board is setup to track upstream
Linux and has been bumped from 4.1 to 4.15 (compared to p1010).
The target does not build uboot and assumes the user still uses the NXP
suggested prebuilts in the SDK2.0 (last release for PowerPC). If a
uboot is required, the source for SDK2.0 can be found in the following
repo.
http://git.freescale.com/git/cgit.cgi/ppc/sdk/u-boot.git/tag/?id=fsl-sdk-v2.0-1703
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Rename the confusing and misleading ts5x00 directory to a real reference
platform name, ts5500. The readme.txt file already states the support
for both TS-5500 and TS-5400 platforms.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump the 3.17 kernel used for the Technologic Systems TS-5500 platform
to the latest LTS kernel 4.14.
This fixes the ts5x00_defconfig build with GCC 6.x.
The linux-3.17.config file has been renamed to linux-4.14.config to
match the new kernel version, and its changes are the result of make
linux-update-defconfig. However only comments are affected.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig fails to build with gcc 6.x, even though we switched to
using gcc 6.x as the default gcc version in May 2017.
This defconfig also hasn't seen any non-mechanical update since
November 2015.
So it's time to get rid of it, in order to remove the following build
failure:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306938
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig fails to build with gcc 6.x, even though we switched to
using gcc 6.x as the default gcc version in May 2017.
It hasn't been updated since April 2017, and the original submitter,
Fabio Porcedda said:
Unfortunately a newer kernel doesn't boot and I don't have the time
to fix the issue. If having a defconfig that doesn't build on gcc
6.x is unacceptable feel free to remove it.
So, let's get rid of this defconfig, which will remove the following
build error:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306952
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Wireless support ends up enabling CONFIG_SYSTEM_TRUSTED_KEYRING, which
requires openssl to be available on the host, so disable wireless
support, which isn't needed in Qemu.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The ORC unwinder requires libelf to be available on the host, so use
the frame pointer unwinder instead. Using the frame pointer unwinder
is probably good enough in our default Qemu configurations.
Wireless support ends up enabling CONFIG_SYSTEM_TRUSTED_KEYRING, which
requires openssl to be available on the host, so disable wireless
support, which isn't needed in Qemu.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig currently doesn't build with GCC6 (Linux 4.1).
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306827
A maintainer w/board isn't available to make updates, so removing
this config.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
>From the original submitter of this defconfig:
"""
I no longer have access to ci40 board. It would be difficult for me to
maintain it.
"""
And this defconfig currently fails to build with gcc 6.x. Therefore,
drop it.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306806
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
No other changes necessary, 4.15 builds and boots fine.
Signed-off-by: Alex Suykov <alex.suykov@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig currently fails to build the Linux kernel:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306826
In addition, the U-Boot build had already been removed in commit
12c01e4a05
("configs/freescale_mpc8315erdb: remove U-Boot build"), back in
October 2016, and nobody bothered fixing it.
This defconfig was originally contributed and maintained by Gustavo
Zacarias, but he is no longer active in Buildroot, and nobody
expressed interest in this defconfig, so let's get rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
In particular:
- Explicitly specify the CPU to be used, POWER8, which matches
qemu_ppc64le_pseries_defconfig
- Use hard disk emulation to access the root filesystem instead of an
initrd.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This allows the toolchain building machinery used by
https://toolchains.bootlin.com to automatically re-use this Qemu
command line.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
qemu-system-ppc64le doesn't necessarily exist: it isn't installed by
Qemu, and only created as a symlink to qemu-system-ppc64 by some
distributions (Ubuntu). Other distributions (Fedora) just have
qemu-system-ppc64.
But qemu-system-ppc64 is capable of running little-endian PPC64
systems, so use this one instead.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Orange-Pi Zero Plus2 board has AP6212 WiFi/BT combo, but does
not have ethernet port. So it makes sense to enable wireless
networking by default:
- add DTS patch enabling AP6212 WiFi/BT combo support
-- this patch is on its way to mainline Linux v4.16
- enable WiFi support in kernel config
- enable Broadcom brcmfmac kernel driver in kernel config
- add Broadcom wireless firmware package to image
- add basic wireless tools to image
- add mdev to image to enable module autoloading
- add rootfs overlay with proper NVRAM file for on-board AP6212 chip
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump versions:
- use U-Boot 2008.01
- use Linux kernel v4.15.2
Drop patch with dts sdcard fix since it has been
merged to Linux v4.15.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With this commit we update Linux kernel version to 4.15 and
Linux headers version to 4.15.
Also patches for arc vdk are removed because these
changes were applied in Linux 4.15.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump Linux to 4.15 and U-Boot to 2018.01. Remove networking dts patches
since they has landed in Linux 4.15. Update readme.txt: fix mainline BSP
versions and update boot selection for board rev 1.3.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add a genimage.cfg to create a working sdcard.img for the ci20
hardware. We also need a uboot-env.txt to create the partition for
the uboot environment.
Update the board/ci20/readme.txt with the related information. Remove
the tftp netboot description from the readme as it is already to
complicated for a basic bootable example.
Signed-off-by: Johannes Schmitz <johannes.schmitz1@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Currently in Orange Pi boards post-build script is used only to generate
U-Boot boot script and post-image script is used only to generate sdcard
image according to genimage configuration. However both those tasks can
now be handled by generic Buildroot tools:
- BR2_TARGET_UBOOT_BOOT_SCRIPT config options
- support/scripts/genimage.sh script
This patch drops custom scripts replacing them
by generic Buildroot tools.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also include new boot scripts to match standard distro uboot commands.
Our previous 6x_bootscript and 6x_upgrade used custom variables and
their naming don't make sense now that we target more than i.MX6 CPU.
Therefore those old scripts are marked as legacy and kept for now but
the goal is to deprecate and remove them later.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also switch repository from old freescale site to codeaurora:
https://source.codeaurora.org/external/imx/
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Orangepi PC2
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Zero Plus2
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Prime
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Win/Win Plus
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Olimex A64-OLinuXino
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Tsvetan Usunov <usunov@olimex.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for FriendlyARM Nanopi NEO2 board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Yuefei <yftan@friendlyarm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for FriendlyARM Nanopi A64
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Yuefei <yftan@friendlyarm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for SoPine board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: TL Lim <tllim@pine64.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Pine64 board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: TL Lim <tllim@pine64.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for bananapi M64 board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Jason <manager@sinovoip.com.cn>
Cc: hailymei@banana-pi.com <hailymei@banana-pi.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add MacchiatoBin board by SolidRun. This board is based on Marvell
Armada 8040 SoC. Board support package includes the following
two options: mainline and vendor BSPs.
Mainline BSP:
- Marvell ATF v1.3-armada-17.10
- mainline U-Boot v2017.11
- mainline Linux kernel v4.14.4
Marvell BSP with more hardware support enabled:
- Marvell ATF v1.3-armada-17.10
- Marvell U-Boot based on v2017.03
- Marvell Linux kernel based v4.4.52
More details about this board are available on wiki:
- http://wiki.macchiatobin.net
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
[Thomas: misc tweaks in readme.txt.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Run-time tested on ZedBoard, build-tested on the other boards]
[Peter: also add host-dosfstools / host-mtools to make vfat images]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
We are about to introduce genimage support for the Zynq boards. For
all of them U-Boot loads the DTB from a file named "devicetree.dtb" so
we need to rename it on the SD card image.
We could use genimage itself to rename files while creating the
image. But this would require a different genimage.cfg for each board,
leading to duplicate code.
Instead let's create a "devicetree.dtb" symlink pointing to the dtb
listed in the configuration. Currently all the Zynq-based boards have
only one DTS configured, but if one had two or more of them, the
symlink would point to the first one.
[Peter: only create symlink if dtb option is available]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This board is quite similar to orangepi-one board. Instead of ethernet, it
has RTL8189FTV SDIO WiFi chip.
Board support package includes the following components:
- mainline u-boot 2017.09
- mainline kernel 4.13.11
Signed-off-by: Jan Kraval <jan.kraval@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This board is a variant of orangepi-pc board. It adds 8GB eMMC and Realtek
RTL8189FTV SDIO WiFi chip. This variant has a separate support in U-Boot
and kernel. So it makes sense to create a separate entry
for this board in buildroot.
Board support package includes the following components:
- mainline u-boot 2017.09
- mainline kernel 4.13.11
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
[Thomas: add entry to DEVELOPERS file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This merges the next branch accumulated during the 2017.11 release
cycle back into the master branch.
A few conflicts had to be resolved:
- In the DEVELOPERS file, because Fabrice Fontaine was added as a
developer for libupnp in master, and for libupnp18 in
next. Resolution is simple: add him for both.
- linux/Config.in, because we updated the 4.13.x release used by
default in master, while we moved to 4.14 in next. Resolution: use
4.14.
- package/libupnp/libupnp.hash: a hash for the license file was added
in master, while the package was bumped into next. Resolution: keep
the hash for the license file, and keep the hash for the newest
version of libupnp.
- package/linux-headers/Config.in.host: default version of the kernel
headers for 4.13 was bumped to the latest 4.13.x in master, but was
changed to 4.14 in next. Resolution: use 4.14.
- package/samba4/: samba was bumped to 4.6.11 in master for security
reasons, but was bumped to 4.7.3 in next. Resolution: keep 4.7.3.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Or1k support improved, f.e. musl can be tested inside qemu.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This helps the toolchains.free-electrons.com build logic re-use
directly the Qemu command lines from this readme.txt file, by having a
-append option similar to the ones used in other readme.txt files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This helps the toolchains.free-electrons.com build logic re-use
directly the Qemu command lines from this readme.txt file, by having a
-append option similar to the ones used in other readme.txt files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6ulevk_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As there is now a defconfig inside kernel sources for mxs platforms, use it.
Signed-off-by: Julien BOIBESSOT <julien.boibessot@armadeus.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This updates the LEGO MINDSTORMS EV3 board to Linux kernel 4.14 and
U-Boot 2017.11.
* Kernel patches are dropped because they are in mainline now.
* This caused the kernel image to be >3M so some adjustments to the image
sizes/layout needed to be made in U-Boot.
* Updated U-Boot version bumped since we are touching this config anyway
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6sx-sdb_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6slevk_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
boot.cmd using dts file instead of dtb which was
added in below commit, so fix the same.
"board: Add Bananapi M1 support"
(sha1: 5f50fb8d1d)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add some documentation about running the pc defconfigs in qemu.
In particular, document the use of the -bios parameter to use the OVMF
firmware to test the UEFI image.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This simplifies the pc configs and respective post image scripts to use
the shared genimage script and separate grub config files.
Separate grub files are cleaner to maintain and easier to copy and
modify, for example to support booting the pc defconfigs in qemu.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for bananapi M1 board with below features:
- U-Boot 2017.09
- Linux 4.13.7
- Default packages from buildroot
Cc: Jason <manager@sinovoip.com.cn>
Cc: hailymei@banana-pi.com <hailymei@banana-pi.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The gpu_mem option is not using the proper option argument which causes sed to
fail.
+ case "${arg}" in
+ gpu_mem=ome/gportay/output-rpi3-qtwe/images
+ sed -e '/^ome/gportay/output-rpi3-qtwe/images=/s,=.*,=ome/gportay/output-rpi3-qtwe/images,' -i /home/gportay/output-rpi3-qtwe/images/rpi-firmware/config.txt
sed: -e expression #1, char 8: extra characters after command
+ case "${arg}" in
+ gpu_mem=ome/gportay/output-rpi3-qtwe/images
+ sed -e '/^ome/gportay/output-rpi3-qtwe/images=/s,=.*,=ome/gportay/output-rpi3-qtwe/images,' -i /home/gportay/output-rpi3-qtwe/images/rpi-firmware/config.txt
sed: -e expression #1, char 8: extra characters after command
The issue comes from the use of $1 instead of $arg to extract the gpu_mem
value. $1 is the $(BINARIES_DIR) which leads to a sed expression error.
Also, it adds the error flag to the shell script to prevent from such situation
and terminate the build in error.
Signed-off-by: Gaël PORTAY <gael.portay@savoirfairelinux.com>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump the kernel to version 4.13.5 and U-Boot to 2017.09.
While at it, remove the custom scripts for generating the SD card image
and use the standard scripts instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The "virt" machine supports disk emulation, so use a ext4 rootfs instead of
initramfs for consistency with the other qemu defconfigs.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Mainline kernel is able to decode video via the coda driver.
Add support for it and also add some explanation on how VPU decoding
can be tested with Gstreamer.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Introduce imx6-sabreauto_defconfig that uses mainline U-Boot and
mainline kernel.
As mainline U-Boot supports SPL, it is possible to boot the same
sdcard.img in the three mx6sabreauto variants: imx6q, imx6dl and imx6qp.
Also update the readme.txt file to explain how to build an image for
mx6sabreauto boards using mainline U-Boot and kernel.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[Thomas: regenerate gitlab-ci.yml file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Improve the explanation of the need for using the performance governor.
This problem is specific to mx6sabresd board and the Egalax touchscreen
running a mainline kernel, so make this clear.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The parts of the readme.txt that specify the board-specific aspects
(DTB files, KMS config json file) were a bit confusing. For the DTB
files this is solved by putting the board it applies to after the DTB
file name. For the json files, this is solved by adding an extra line,
so the CinematicExperience-demo is clearly separated from the setting
of QT_QPA_EGLFS_KMS_CONFIG.
Also remove the 'for all boards' line in the beginning, it doesn't add
any value.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This patch add support for Open Frame C.TOUCH 12 Kit.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This patch add support for Open Frame C.TOUCH 10.1 Kit.
Since the defconfig is no longer only for the starter kit, remove that
from BR2_TARGET_GENERIC_ISSUE.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add the new SAMA5D27 SOM1 Evaluation Kit with linux4sam_5.7 components.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The amount of GPU memory can be set using the new option --gpu_mem_XXX
(where XXX is the total amount of memory available on the board).
Signed-off-by: Gaël PORTAY <gael.portay@savoirfairelinux.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add an entry to explain how to run the glmark benchmark.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Bump the kernel version to 4.13.3.
Kernel 4.13.3 uses the /dev/dri/card0 device as rendering node, so
adjust it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
U-Boot 2017.09 uses SPL, so bump to this version so that we can
have a single qt5 image that supports the different imx6 sabresd
boards: imx6q, imx6dl and imx6qp.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Now that SPL is supported a single image can run on the different
variants of imx6 sabresd boards: imx6q, imx6dl and imx6qp.
So drop the 'quad' prefix from defconfig, directory and readme file
to make it generic.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Pass an offset of 1MB for the start of the rootfs.
Otherwise we get rootfs corruption when the bootloader is manually
written to the SD card.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This is similar to the ppc64_pseries config, except we build for little
endian instead of big endian.
The default architecture is set to Power8 as this was the first fully
enabled LE machine.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Peter: board is from Sinovoip, not Lemaker, move board files,
Use kernel headers from kernel, explicitly use 4.13.3,
drop eth0 dhcp config, cleanup post-build args,
disable tar output format, use u-boot custom format,
add host-dosfstools/mtools for genimage, drop unused
host-uboot-tools/genext2fs]
Signed-off-by: Mike Harmony <mike.harmony@snapav.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump to 4.13 kernel and remove all the dts patches as they
are part of upstream now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Kernel help-text states, "The ext4 filesystem requires that this feature
be enabled <...> otherwise, it will refuse to mount in the read-write
mode any filesystems that use the huge_file feature, which is enabled by
default by mke2fs.ext4."
If the rootfs is to be (re)mounted rw at boot, this must be set for the
system to successfully come up.
Signed-off-by: Nicholas Sielicki <sielicki@yandex.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The TS-7680 is an i.MX286 ARM ARM926EJ-S board with 10/100 Ethernet,
USB port, eMMC and CAN ports.
The TS-7680 uses a 3.14.28 Linux kernel provided by Technologic Systems:
https://github.com/embeddedarm/linux-3.14.28-imx28
U-Boot is not provided as the manufacturer recommends not to update the
built-in bootloader.
For more informations please see:
https://wiki.embeddedarm.com/wiki/TS-7680
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
[Thomas: use same headers as the kernel being built, update .gitlab-ci.yml.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
i.MX1/L boards require an old Linux kernel version to run, which is not
compatible with latest Buildroot needs.
Will fix:
https://gitlab.com/buildroot.org/buildroot/-/jobs/27873568
Signed-off-by: Julien BOIBESSOT <julien.boibessot@armadeus.com>
[Thomas: update .gitlab-ci.yml file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Our new WiFi 802.11ac BT4.1 module (BD-SDMAC [1]) driver allows to
override the wlan MAC address using a module parameter.
Since its driver is now included in our external repository [2], update
the bootscript so it sets the parameter for that driver too.
As a FYI, $wlmac is based on Ethernet MAC address located in fuses.
[1] https://boundarydevices.com/product/bd_sdmac_wifi/
[2] https://github.com/boundarydevices/buildroot-external-boundary
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx7d-pico, which is a board based on NXP
i.MX7D processor.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
[Thomas:
- add upstream references for the Linux kernel patches
- fix typoes in readme.txt
- remove audio-related packages in defconfig
- regenerate .gitlab-ci.yml]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The beaglebone_qt5_defconfig uses an older kernel version which does not
provide a device tree for the beagle bone green.
post-image.sh now selects genimage_linux41.cfg if am335x-bonegreen.dtb is
not build and genimage.cfg otherwise.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
[Thomas: minor tweaks.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Introduce imx6q-sabresd_qt5_defconfig that supports the opensource
Etnaviv graphical stack.
This defconfig provides a way to quickly test some graphical applications,
such as kmscube, qt5, glmark2.
Currently kernel mainline exhibits issues when running cpufreq as ondemand
governor on mx6, so add a linux fragment that disables such option for the
time being.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[Arnout:
- Add Fabio to DEVELOPERS
- Rename linux config fragment to linux_qt5.fragment
- Add comment to linux_qt5.fragment why it is needed
- Add explicit CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y to it
- Reorder defconfig entries to they match imx6q-sabresd_defconfig
- Remove strace and host-uboot-tools, neither seems to be needed
- Drop BR2_PACKAGE_QT5BASE_LICENSE_APPROVED, it no longer exists
- Replace BR2_TARGET_ROOTFS_EXT2_BLOCKS with BR2_TARGET_ROOTFS_EXT2_SIZE
- Regenerate .gitlab-ci.yml]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Bump U-Boot to 2017.07 and kernel to version 4.12.3.
As imx_v6_v7_defconfig in 4.12 selects CONFIG_CFG80211_WEXT=y,
remove the linux.fragment file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for nanopi-m1-plus board
with below features
- U-Boot 2017.07-rc3
nanopi-m1-plus dts support is present in rc3 version
- Linux 4.11.5
- linux patches to add nanopi-m1-plus dts
- Default packages from buildroot
Signed-off-by: Chakra Divi <chakra@openedev.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
And drop the version number from the linux configuration.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Drop the board specific patches which has been applied upstream.
[Peter: also drop now unused BR2_GLOBAL_PATCH_DIR]
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit adds a Linux kernel patch to solve a build failure with
the arcturus_ucp1020_defconfig with gcc 6.x:
arch/powerpc/kernel/ptrace.c:407:24: warning: index 32 denotes an offset greater than size of 'u64[32][1] {aka long long unsigned int[32][1]}' [-Warray-bounds]
offsetof(struct thread_fp_state, fpr[32][0]));
^
The patch is upstream in Linux, and can be dropped when
arcturus_ucp1020_defconfig is updated to use a new Linux kernel
version.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Main difference is that the drm driver now supports the hdmi output.
The gxl variant device tree has been renamed in:
commit 7eea67101b9713ae438955e8899b3c4b078419f9
Author: Kevin Hilman <khilman@baylibre.com>
Date: Fri Jan 20 07:57:52 2017 -0800
ARM64: dts: meson-gxl: rename Nexbox A95x for consistency
Since the GXL family has S905X and S905D SoCs, we're keeping the SoC
name in the DTS filename for clarity. Rename this file accordingly to
be consistent with the rest of the GXL DTS files.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
So adjust the defconfig and boot script to match.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Rather than bundle the overlay with us, directly fetch it from its
upstream location.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for nanopi-m1 board
with below features
- U-Boot 2017.07-rc1
- Linux 4.11.5
- Default packages from buildroot
Signed-off-by: Chakra Divi <chakra@openedev.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Manual change because the script uses ${OUTPUT_DIR}/host instead of
${HOST_DIR}.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Manual change because the script uses ${OUTPUT_DIR}/host instead of
${HOST_DIR}.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Since things are no longer installed in $(HOST_DIR)/usr, the callers
should also not refer to it.
This is a mechanical change with
git grep -l 'HOST_DIR}\?/usr/' board | xargs sed -i 's%\(HOST_DIR}\?\)/usr/%\1/%g'
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Chakra Divi <chakra@openedev.com>
[Thomas: remove host-uboot-tools from defconfig, already pulled by
BR2_TARGET_UBOOT_BOOT_SCRIPT, remove trailing whitespace.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Engicam Is.IoT MX6UL SOM board
with below features:
- U-Boot 2017.07-rc1
- Linux 4.11.5
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas: add host-dosfstools/host-mtools.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
