Signed-off-by: Carlos Quijano <carlos@crqgestion.es>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Bump for a slew of USB-related and other fixes.
The bcmrpi defconfig is a huge beast with lots of superfluous drivers.
The brcmrpi_quick defconfig is a stripped down minimalist defconfig with
all that is needed to bring up a RPi with complete HW support, and
nothing superfluous, which is what we need for a board's defconfig in
buildroot.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Wandboard is a low cost iMX6 system consiting of an EDM standard
processor module and a small base board.
http://www.wandboard.org
Signed-off-by: Stephan Hoffmann <sho@relinux.de>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The 3.10.x kernels fail to build with the following message:
vsprintf.c:(.text+0x17e0): relocation truncated to fit: R_AVR32_16N_PCREL against symbol `_ctype' defined in .text section in lib/lib.a(ctype.o)
While this is most likely a toolchain issue, but since AVR32 isn't a
well-maintained architecture, there's not much we can do.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump for a few fixes:
- fix for slow SDcards
- fix for USB interrupts
- fix for tracing functions
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
While at it add the missing network interfaces to configurations that
support it.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Misc fixes and enhancements:
- faster image blitting in framebuffer
- USB fixes, and use of FIQ instead of plain IRQ
- generic ARM fixes for memset
- BT l2cap fix
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Fixes in GPIOs, I2C and DMA.
And since the RPi git tree fork has a non-upstream driver
for rtl8192c WiFi USB stick, there's a fix for that, too.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
[Peter: lock kernel/headers version to 3.9.4, use devtmpfs, add comments]
Signed-off-by: Gregory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
[Peter: adjust for _FEX_FILE]
Signed-off-by: Carlo Caione <carlo.caione@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Add the FW needed for the Cortex M3 on the beaglebone. This is required
for working power management.
Signed-off-by: Anders Darander <anders@chargestorm.se>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
As the beaglebone support is mainlined, there's no support for the old
board setup files, and the only supported run-time configuration is through
the device tree.
We're also setting the kernel headers to follow the 3.8 series.
Signed-off-by: Anders Darander <anders@chargestorm.se>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
This is a configuration that provides a basic setup for generating
bootable nandflash images:
- at91bootstrap
- barebox
- kernel
- rootfs
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
For more info, please read board/telit/evk-pro3/readme.txt
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Some board configs where left out of the u-boot custom version
migration, so do it otherwise they'll just pull the latest version which
might not work and brick the device.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Commit 75b7dc68 ("linux: default to 3.9, remove 3.8") made 3.9 the
default kernel version.
The omap kernel switched to multiplatform kernel during the 3.9 kernel
development cycle. Obviously, the uImage generation doesn't work anymore
with multiplatform kernels, since you have to provide the kernel load
address, resulting in a build error.
Lock down the kernel version to 3.8 to keep the old behaviour until
someone submits a patch to switch to multiplatform kernel.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
the integrator926 defconfig has not been updated for quite some time,
and is still asking for very old linux and u-boot releases. Now that
these versions aren't present in Buildroot anymore, they default to a
newer release, where, in the u-boot case, the defconfig name has
changed, leading to a build failure.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Commit a0b6faa ("gdb: convert to the package infrastructure") changed
the name of the host gdb configuration option, and added it to the
legacy option set, leading to a build breakage for the
armadeus_apf9328_defconfig.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
The IRQ mapping failures have been fixed in 3.8.8 so update it to the
latest kernel series.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Buildroot toolchain, UBIFS rootfs, Linux kernel (board is mainlined since 3.8).
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Somehow the old setting wasn't dropped in 184850a42 (bump u-boot /
linux versions to current stable).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
This is a default configuration for the RaspberryPi, tested and functional.
The kernel used is the one developped by the RaspberryPi foundation as
it's not fully supported currently in mainline kernel. The configuration
used for the kernel is the default bcmrpi.
For more info, please find board/raspberrypi/readme.txt
[Peter: minor README tweaks, rename to readme.txt]
Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
[yann.morin.1998@free.fr: use correct kernel headers, update kernel cset]
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Buildroot toolchain, UBIFS rootfs, Linux kernel (board is mainlined
since 3.8).
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Problematic configurations not bumped:
arm-versatilepb - IRQ failure for symbios scsi
sh4-r2d - Qemu still doesn't emulate advanced features from the UART
sparc-ss10 - Illegal instruction
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Update {ea3250,fdi3250,phy3250}_defconfig to lock down kernel headers to
an appropiate version.
Otherwise the target is building with, at the moment of this writing,
version 3.7 headers and a 2.6.34 kernel which usually isn't wise.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Update to the latest maxim.org.za kernel 2.6.38
Lock down headers version, otherwise we were building a toolchain with
3.7 headers for a 2.6.33 kernel - not too wise.
Also the AT91RM9200 is an ARM920T so enable that target.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Switch to generic V8 optimization for gcc since we dropped the explicit
supersparc one and works just the same.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Bump to use kernel 3.7.1
Switch to hard float toolchain with NEON and VFP support.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
The board boot more fast with a zImage than a uImage
as the kernel will not have to be relocated during the decompression.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Note that this configuration doesn't build entirely: the user must
manually run "make busybox-menuconfig" and disable the "Mount NFS
filesystems" option, because the toolchain does not have RPC support.
This issue will be fixed once the support for toolchain without RPC
will be integrated.
[Peter: fix readme typo]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Notice that you need u-boot >= 2012.04 to be able to boot kernel >= 3.2,
because older u-boots keep the l2 cache enabled, see u-boot commit
679530278 (arm, arm-kirkwood: disable l2c before linux boot) for details.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Update to use the latest kernel 3.5.4.
And also update to the latest .config knobs, otherwise we were just
building a mips(32) target which failed miserably.
This config is still flaky, you get a login prompt but usually fail to
login, passing along an init=/bin/sh helps some but crashes are quite
usual.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Update the qemu samples configs that used kernel 3.3.4 to 3.3.5
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Beautify and lock down kernel version to avoid future issues.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Beautify and lock down kernel version to avoid future issues.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Add new powerpc-mpc8544ds sample qemu config.
Useful for SPE ABI testing.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
This configuration provides a basic setup for using Buildroot
to create all of the images needed for a BeagleBone.
Signed-off-by: Frank Hunleth <fhunleth@troodon-software.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
This is a default configuration for Panda and PandaES, tested on both
platforms.
DEVTMPFS is enabled, to use static dev configuration one would need
to update the generic dev table for ttyO driver.
Panda is well supported in mainline kernel with omap2plus_defconfig,
so this should be safe.
U-boot SPL support is enabled by default as x-loader is now
deprecated.
With OMAP platforms u-boot,img format is prefered now, so it's enabled
by default as well. Also, on PandaBoard, the name of SPL target file
is MLO.
Signed-off-by: Nicolas Dechesne <n-dechesne@ti.com>
Acked-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Bump to use kernel version 3.2.16
Still keep sh4-r2d qemu sample config on 3.2 series since the sh-sci
driver from 3.3 uses unimplemented functionality (as of qemu 1.0.1)
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Target a powerpc 750 rather than the incorrect 440fp to avoid issues and
for correctness.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
[Peter: also add to 9g0dfc]
Signed-off-by: Alexandre Belloni <alexandre.belloni@piout.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Also switch documentation to use qemu-system-i386
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Unfortunately kernel 3.3 doesn't seem to work properly at the moment.
So lock down headers to version 3.2.x and kernel to 3.2.12.
Tested on qemu 1.0.1
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
The Avnet S6LX9 Microboard is a small USB-Stick sized module
containing a Spartan6 FPGA capable of running the Microblaze
softcore processor together with RAM and FLASH memory.
This board support pachage assumes that the Microblaze Bitfile
available from the Avnet website is programmed into the FPGA.
Signed-off-by: Stephan Hoffmann <sho@relinux.de>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Drop the patch for kernel >= 3.3
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
at91sam9260_defconfig contains support for the EVM (since v3.2).
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
- Use git:// URLs for freescale git trees
- Enable hard fpu for A8
- Board uses uSD cards, so enable ext2 filesystem
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Buildroot config and Linux Kernel config.
Freescale binaries (xf86 video driver and multimedia codecs) not supported yet.
Signed-off-by: Mathieu Briand <mbriand@adeneo-embedded.com>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
While upgrading the configs, it proved necessary to make more space on
the dataflash for u-boot since it grew because of relocation.
dataflash is then repartitionned to make more room for u-boot and a redundant
environment.
Signed-off-by: Alexandre Belloni <alexandre.belloni@piout.net>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Add a new qemu_mips_malta sample configuration for big endian MIPS
testing.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Update configuration to use kernel version 3.2
Also update the readme to use buildroot basedir as a reference for
kernel and rootfs like the other samples do.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
The APF9328 is an i.MXL+FPGA based SOM (System On Module). Here only minimal
support is added: booting Linux kernel (UART, Ethernet and NOR), Buildroot
toolchain and JFFS2 rootfs.
[Peter: Remove redundant BR2_TARGET_OPTIMIZATION]
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Add a new qemu sample config for the SPARC architecture.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
sh4-r2d has a serial port, however it's the second SH UART that's
emulated by Qemu so we need to adjust the kernel configuration for it to
see the relevant UART and adjust the qemu command line for it too.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
mini2440 has been supported in the mainline kernel since early 2009,
so use that instead of a custom tarball.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Bump kernel versions of qemu/mips-malta and qemu/arm-versatile sample
configuration files to 2.6.38.6
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
This way we'll get something in images/ by default, and hopefully people
will be less likely to try to use target/ directly.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
It's pretty uncommon to use ext2fs on embedded systems, so don't enable
it by default.
Adjust defconfigs to match.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
It's really not very useful, all it does is install a target
strace and ldd in a target_utils directory in staging.
While at it clean up the strace makefile a bit.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
[ Thomas:
* renamed sh4_defconfig to qemu_sh4_r2d_defconfig, for consistency
with other Qemu platforms supported
* renamed board/qemu/sh4 to board/qemu/sh4-r2d
* minor fixes in the readme.txt
* remove useless statements in the minimal defconfig
* switch to a fixed kernel version instead of "same as headers"
]
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Paul Jones documented at
http://pauljones.id.au/blog/2010/07/using-buildroot-on-a-mini2440/ how
to use Buildroot to generate a system for the FriendlyARM Mini2440
platform. This patch integrates Paul's work into Buildroot.
Unfortunately, the kernel being 2.6.32, we can't easily use a minimal
defconfig here. The mini2440 support has been merged into more recent
kernels, but I don't have the hardware to test.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
This default configuration did not even build a kernel image, which is
the main point of having board default configuration. So remove it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Neither the kernel nor U-Boot have support for a 1005 board, so let's
get rid of this board configuration, the corresponding target
skeleton, kernel and busybox configuration and device table.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Use recent U-Boot and kernel version, remove target skeleton and use
the default one instead, remove useless kernel configuration, busybox
configuration and device table.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
It was supposed to be the support for AT91SAM9260 using a parallel flash
(instead of the usual dataflash). But the provided U-Boot configuration
at91sam9260pf.h was not used anywhere, and it was unsufficient to add
correct support in U-Boot (some changes in U-Boot Makefile would also be
needed). Additionnally, this configuration has not been merged into U-Boot
upstream since 2007 (when it was added to Buildroot).
Therefore, let's get rid of this configuration. If some users are
interested, we can re-introduce it properly with their help.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Use recent U-Boot and kernel versions, remove useless kernel
configuration file.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Use recent U-Boot and kernel versions, remove useless kernel
configuration file.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Minimize the board defconfig, remove custom busybox configuration,
custom kernel configuration (use the kernel defconfig instead), custom
device table and target skeleton. The only difference in the target
skeleton was the support of mdev and the usage of an automount
script. Instead of adding this in a board-specific way, we should
provide board-independent configuration options. There are already
patches contributed to add support for mdev.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Minimize atngw100_defconfig, remove atngw100-base_defconfig, and
remove the target skeleton and device table. Instead of having
complete copies of new target skeletons (making them hard to
maintain), we should just have a post-build script that
adds/removes/tweaks the existing target skeleton.
Moreover, most of the tweaks in this target skeleton were for specific
packages, but the policy now is that board defconfig should just build
a basic root filesystem with Busybox, and let the user select
whichever set of packages (s)he wants.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Those are not associated with any specific hardware system (PC or
another i386 system). Moreover, the fact that those configurations
require the build of a JFFS2 filesystem, very uncommon on PC systems,
seems to indicate that those configurations are not really being used
today.
It would make more sense to have a qemu_i388_defconfig (building a
kernel with just the device drivers for Qemu) and possibly a
pc_i386_defconfig (building a kernel with many device drivers, and a
bootloader such as Grub or Grub 2).
We also remove the corresponding kernel configuration files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
One config per board is enough.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Use modern U-Boot and kernel versions, get rid of the now unused
kernel configuration file since we use the kernel defconfig instead.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Use modern U-Boot and kernel versions, and get rid of the useless
kernel configuration file, since we now use the kernel defconfig.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Use modern kernel and U-Boot versions, and get rid of the now useless
kernel configuration file since we use the kernel defconfig file
instead.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
The configuration cache shared between packages, while being in
principle a nice idea to speed-up the configuration of packages by
avoiding repetitive identical checks, turned out to be unreliable due
to the subtle differences between similar but not identical checks in
different packages. After spending some time trying to fix those, we
concluded that supporting the shared configuration cache is definitely
too hard and too unreliable, and that we'd better get rid of it
altogether.
This patch therefore removes the shared configuration cache
infrastructure and usage.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
As stated on http://pcmcia-cs.sourceforge.net/: "The Linux pcmcia-cs
package is officially deprecated. It can only be used with 2.4 and
older kernels.".
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch modifies current toolchain build sequence so that
NPTL enabled toolchain can be built. The new sequence works
well with linuxthreads as well.
It introduces a new pass for gcc cross compilation. The new
sequence is binutils->gcc-initial->linux-headers -> uclibc-configured
(some cheats to generate phony shared libc.so and libm.o)
-> gcc-intermediate(with shared lib support) -> uclibc -> gcc-final
I also added a new sample config arm_nptl_toolchain_defconfig which
builds the toolchain and busybox.
I have only tried it on arm. However it should work for other
architectures which support NPTL on uclibc e.g. mips, sh, x86, ppc, x86_64
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Supporting multilib is much more than just passing --enable-multilib
to gcc. You have to actually build the C library several times (once
for each multilib variant you want to support in your toolchain), and
to pass MULTILIB_OPTIONS/MULTILIB_EXCEPTIONS values to gcc to let it
know the set of multilib variants you're interested in.
Since we'll probably never support multilib toolchains in Buildroot,
just get rid of this BR2_ENABLE_MULTILIB option.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is a very advanced option, and it seems, according to
http://choices.cs.uiuc.edu/exceptions.pdf that SJLJ exceptions aren't
really interesting.
Users really interested by this can always use the
BR2_EXTRA_GCC_CONFIG_OPTIONS is they want.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The buildroot/busybox/uClibc VM is running low on disk space, and we've
been asked to move the source mirrors off-site.
A redirect has been setup between the old buildroot.net/downloads/sources/
and sources.buildroot.net, so old .configs continue to work, but we might
as well use the official one now.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
atngw100_defconfig: update to fix build failure:
* The AVR32 toolchain fails to build with the new uClibc version
0.9.31.x. Use the older uClibc 0.9.30.x branch instead.
* Disable linux-fusion as it fails to build
(why was this selected anyway, when DirectFB was not selected?).
* U-Boot 2010.03 is broken for AVR32. The build fails with:
zlib.c:31:27: error: asm/unaligned.h: No such file or directory
Select the older U-Boot 2009.08 version that builds instead.
* Disable rsync as it fails to build.
Build tested with 'make distclean && make atngw100_defconfig && make'
on an Ubuntu 10.04 x86_64 host.
Signed-off-by: Bjørn Forsman <bjorn.forsman@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
We only bother updating the defconfigs that need a non-default
BR2_ROOTFS_DEVICE_TABLE value.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Closes#817 + #1189
Signed-off-by: Johan Thelin <johan@thelins.se>
Signed-off-by: Grant Edwards <grant.b.edwards@gmail.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Reported by Grant Edwards <grant.b.edwards@gmail.com>
Use the new default STAGING_DIR location (output/staging) in all the
defconfigs for clarity.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Invert the BR2_PACKAGE_BUSYBOX_HIDE_OTHERS option to use positive logic,
renaming it to _SHOW_OTHERS.
Positive logic is simpler to understand, and it makes all{,package}config
do the right thing.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
It looks like that nobody is using the commercial license option
because the code is broken (BR2_QT_COMMERCIAL_PASSWORD typo) and
dist.trolltech.com became silent long ago and nobody complained about.
So remove the broken and unused stuff.
Signed-off-by: Michael Roth <mroth@nessie.de>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
The Kconfig menu "Pixel depths" of Qt provides a list with all
selectable pixel depths and additionally the option "all".
When "all" is selected, the list with all available pixel depths
disappears.
Because this disappearing of available pixel depths makes no sense
under usability aspects, simply remove the option "all".
The user could enable all available pixel depths by selecting each
individual depth anyway. So no functionality is lost.
Signed-off-by: Michael Roth <mroth@nessie.de>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
As discussed earlier on the mailing list. It simplifies code, gives more
sensible error message on typos and makes the defconfigs easier to find
for users.
Furthermore, update documentation to match.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
