Commit 68b5b79b2f has set the getty port to the default console but left
"ttyO0" in bootargs, in the U-Boot environment. Use "ttyS0", instead.
Also set loadaddr to 0x82000000 and fdtaddr to 0x88000000, replacing the
values that were valid for the ancient U-Boot and Linux pre-installed on
old boards but cause boot hangs with the current versions.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Thanks to the introduction of GPT partition table support in genimage,
this commit improves the pc_x86_64_efi_defconfig to remove the use of
the custom script creating the image.
Tested in QEMU, not on a physical device.
So:
- revert commit fee29b05bb7db25e37c8a5175ce00dc712554edf[1]
- add GPT support
- tweak shell script to add the correct UUID in genimage config.
[1]: https://git.buildroot.net/buildroot/commit/?id=fee29b05bb7db25e37c8a5175ce00dc712554edf
[2]: https://git.buildroot.net/buildroot/commit/?id=79b8540d624ac4846ba341b1b9691eccacf0bc05
Signed-off-by: Alexandre PAYEN <alexandre.payen@smile.fr>
Cc: Carlos Santos <casantos@datacom.com.br>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[Thomas:
- drop commented code in post-build.sh
- take into account comments made by Carlos Santos in
http://patchwork.ozlabs.org/patch/1143502/]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use the pi3-miniuart-bt device tree overlay (as the 32bit raspberrypi3
defconfig) instead of the enable_uart option.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes reference path "../build/optee_os-" to "./output/build/optee-os-"
as package is optee-os and symbol file here is reached from BR top
dir and assuming output in output/.
Updates GDB tool name to arm-linux-gdb.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This change introduces a Qemu board for an Armv7-A target executing
with OP-TEE secure world services. The target Linux based normal world
embeds the standard minimal filesystem with OP-TEE non-secure components
embedded files from OP-TEE test, examples and benchmark packages.
qemu_arm_vexpress_tz_defconfig differs from qemu_arm_vexpress_defconfig.
Supporting both secure and non-secure worlds on the Arm target mandates
a secure world, here OP-TEE OS, and a bootloader to boot both worlds,
here TF-A (boot/arm-trusted-firmware). Here non-secure Linux kernel is
booted through U-boot
TF-A bootloader (BL1/BL2) => OP-TEE (BL32) => U-boot (BL33).
| Executes as secure | Secure | Execs as Non-secure
| Loads BL32/BL33 in RAM | Jumps to BL33 | Always booted after
| Jumps to BL32 once done | as Non-secure | secure world inits
Vexpress and vexpress-tz defconfigs also differs in that Qemu emulates
a Cortex-A9 in the former and a Cortex-A15 in the later. Cortex-A15
is the Armv7-A CPU used in upstream TF-A and OP-TEE OS packages hence
selected here.
Defconfig adds a fragment to the Linux kernel native configuration to
enable OP-TEE driver support.
Defconfig adds a fragment to the U-Boot native configuration set boot
command, enable semihosting and remove U-Boot persistent environment
storage support.
The defconfig also enables build of the Qemu emulator in case the
system installed Qemu does not yet support CPU TrustZone secure state.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
[Arnout, with the help of Peter: correct spelling mistakes in readme,
fix U-Boot version to 2019.01, download tarball of TF-A instead of git]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
That is useful and needed for upcoming introducing stm32mp157a-dk1 board.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
genimage makes a full copy of the given rootpath to ${GENIMAGE_TMP}/root
so passing TARGET_DIR would be a waste of time and disk space. We don't
rely on genimage to build the rootfs image, just to insert a pre-built
one in the disk image.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Use a post-build script to copy uEnv.txt to BINARIES_DIR, as made for
beagleboneai.
Keep the post-image script because it is still used by beaglebone_qt5.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Change partition name according to the U-Boot requirements.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
QT_QPA_EGLFS_ALWAYS_SET_MODE=1 needs to be exported, otherwise the Qt5
Cinematic demo throws a storm of the following messages:
Could not queue DRM page flip on screen LVDS1 (Invalid argument)
Improve the instructions by mentioning such requirement.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 5facee5cc3 ("configs/solidrun_clearfog_gt_8k: bump versions of
BSP components") broke automatic load of the mv88e6xxx dsa driver. The
kernel configuration makes the driver a module, which is not loaded
automatically at boot. Mark mv88e6xxx dependencies built-it to fix that.
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add basic support for the Libre Computer "La Frite" SBC.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since the bump to the 20190819 snapshot there is now a dedicated dts file
for the rpi0, so use that rather than the rpi-b-plus one:
bd1336d8b6
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes#12816
Commit 42d22f3bdb ({configs/raspberrypi,package/rpi-firmware}: bump
kernel/firmware to 20190819 version) updated the kernel version but failed
to take into consideration that the rpi0w dts file has been renamed:
6f91b5dbfd
Fix it by renaming the dts/dtb file referenced from the kernel build and
genimage.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489410
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489367
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489328
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489329
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489325
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig has been failing to build since we switched the default
gcc version to gcc 8.x, as the Linux kernel version is too old and
doesn't contain the necessary fixes to build with gcc >= 8.x.
Despite several pings to the original submitter of the defconfig
(which is not listed in MAINTAINERS), no fix has been sent, so it is
time to drop this defconfig before the 2019.08 release.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489442
Cc: Patrick Keroulas <patrick.keroulas@savoirfairelinux.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The TS-7680 defconfig does not build with gcc 8.x and 9.x because it
uses an old 3.14 kernel. Technologic Systems, the board manufacturer
recently released an updated 4.9 based kernel on a separate repository
on github.
Bump the kernel release from 3.14.28 to 4.19.186 and update the linux
defconfig name as requested in the TS-7680 documentation [1].
[1] https://wiki.embeddedarm.com/wiki/TS-7680#Linux_4.9.y
Signed-off-by: Julien Grossholtz <julien.grossholtz@openest.io>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit adds a minimal defconfig to build a Buildroot system for
the STM32MP157 Discovery Kit, which is the low-cost evaluation
platform for the new STM32MP157 system-on-chip from ST. This
system-on-chip features a single or dual Cortex-A7, a single
Cortex-M4, and a wide variety of peripherals.
This commit includes a custom linux configuration file, because there
is no specific defconfig for this platform in the kernel, only
multi_v7_defconfig supports it, which is really a massive
defconfig. That's why a custom linux configuration file is added.
A small U-Boot config fragment allows to disable the watchdog, so that
userspace by default doesn't need to have a watchdog daemon running.
The vendor U-Boot and Linux trees are used for the moment, but the
platform support is being upstreamed, so switching to upstream
versions will be possible in the relatively near future.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This is based on the pi3 defconfig. There is currently no 64-bit support
since the upstream kernel does not build in this configuration.
Signed-off-by: Michael Cullen <michael@michaelcullen.name>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch adds support for the HiFive Unleashed board. This includes
building the firmware, kernel and rootFS for the HiFive Unleashed.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
[Thomas:
- fix the directory name hifive_unleased -> hifive-unleashed
- drop from readme.txt the instructions about manually flashing each
partition, since we have a full SD card image
- drop the custom post-image.sh script]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Custom u-boot
Linux v5.1
ATF v2.0
Buildroot default packages
Tested-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1
- Use final 5.1 kernel
- Use default ext2 filesystem]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
u-boot v2019.04
Linux v5.0
Buildroot default packages
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas: use BR2_TARGET_UBOOT_BOOT_SCRIPT to generate the U-Boot
script, instead of doing it in the post-build]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux 5.1
Custom U-Boot
Arm Trusted Firmware v2.0
Buildroot default packages
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use the headers from the kernel, by using
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1=y
- Use the default ext2 rootfs size]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux 5.1
Custom U-Boot
Arm Trusted Firmware v2.0
Buildroot default packages
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use the headers from the kernel, by using
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1=y
- Use the default ext2 rootfs size]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux 5.1
Custom U-Boot
Arm Trusted Firmware v2.0
Buildroot default packages
Tested-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use the headers from the kernel, by using
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1=y
- Use the default ext2 rootfs size]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux v5.2
Custom U-Boot
Arm Trusted Firmware v2.0
Buildroot default packages
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use the kernel headers from the kernel, by using
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_2=y
- Use the final 5.2 kernel instead of rc1.
- Use the default ext2 rootfs size]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The most important change is to use the toolchain compiled by
buildroot itself. We also bump kernel to 5.0 with kernel.org.
Gx6605s' PHYS_OFFSET if 0x10000000 and we make qemu and gx6605s the
same to ease maintaince. This PHYS_OFFSET is also OK for 610 qemu.
In this patch we add gx6605s.dts in board/csky, because linux-5.0
doesn't contain gx6605s.dts in its tree.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Display variant dtbs are no longer part of the linux-at91 tree.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
PowerPC kernel developers were after a userspace for testing 32-bit
powerpc kernels. This machine both suits that requirement and has
support in qemu. It's also a fairly common piece of 32-bit ppc hardware.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Daniel Axtens <dja@axtens.net>
[Peter: lock kernel/headers to 5.2.4]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to 2019.07 and kernel to version 5.1.16.
Also
- adjust the U-Boot binary name after DM conversion.
- add missing notes about DFU
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Also
- adjust the U-Boot binary name after DM conversion.
- add missing notes about flashing U-Boot and SPL
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
For boards like imx7d-pico, u-boot.img changes to u-boot-dtb.img in
U-Boot v2019.07. Therefore, we need to pick u-boot.img or u-boot-dtb.img
depending on the board configuration.
Just like was done in commit 52344e556f for the generic genimage
template, replace the U-Boot file name with UBOOTBIN, which is set
according to the BR2_TARGET_UBOOT_FORMAT_* option. We also need to set
the correct value for this variable for the u-boot.img and
u-boot-dtb.img cases.
While we're at it, rename the partition from 'u-boot-img' to 'u-boot',
to stay consistent with the generic genimage template.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
[Arnout: correct u-boot.img condition, rework commit log]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
On my machine, it happens once in a while that the virtualised machine
boots too fast for the rootfs to be available at the time the kernel
tries to mount it.
For example, board/qemu/arm-vexpress/readme.txt suggested changing
"-smp 1" up to "-smp 4". But doing so here causes a kernel panic:
VFS: Cannot open root device "mmcblk0" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
1f00 131072 mtdblock0
(driver?)
1f01 32768 mtdblock1
(driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(0,0)
So, add the oh-so-useful 'rootwait' option to all kernel command lines
for qemu defconfigs.
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Mark Corbin <mark.corbin@embecosm.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump Linux and U-Boot versions.
The Linux configuration file and patches are no longer needed.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
[Thomas: also use a tarball for U-Boot.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the 32-bit defconfig to use the latest kernel. This requires a
patch to revert a ABI to ensure that the glibc port continues to work.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for the SolidRun Armada 8040 based Clearfog GT-8K. This
board has the same processor as the Macchiatobin, so we can reuse the
Macchiatobin U-Boot and image definitions.
The kernel fragment enables drivers that are necessary to make
networking ports work (SFP, Ethernet port, and Ethernet switch).
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump Linux to 5.1 and U-Boot to version 2019.01.
U-Boot patch is no longer needed, applied upstream.
U-Boot defconfig name for this board has changed to pico-pi-imx7d.
U-Boot now supports distrobootcmd for this board, so add the appropriate
extlinux.conf and use SPL+u-boot.img instead of u-boot.imx. Note that
the common freescale post-image script handles things appropriately
based on the selected options in .config.
dosfstools and mtools are no longer needed to build the image.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
[Arnout: remove BR2_PACKAGE_HOST_DOSFSTOOLS and BR2_PACKAGE_HOST_MTOOLS]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Modern U-Boot assumes a layout where the first partition is an ext2 and
the kernel and dtb can be found in /boot. In other words, a layout
without boot partition.
Add a genimage.cfg template for the freescale defconfigs with such a
layout.
For now, only the layout with SPL+u-boot.img is added. It's unlikely that
the u-boot.imx approach will be used.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
For the boot image creation for the i.MX8MM, the main differences with
i.MX8M are that there is no HDMI firmware image passed, and the ATF
load address is different.
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Following commit fee29b05bb
("configs/pc_x86_64_efi: use a GPT partition table"),
board/pc/grub-efi.cfg is no longer used anywhere: the
post-image-efi-gpt.sh script generates the grub configuration.
Also, since post-image-efi-gpt.sh generates a grub configuration file
that uses the root filesystem partition UUID as the root= kernel
argument, the instructions in the readme.txt file to tweak root= from
/dev/sda2 to /dev/vda2 is no longer relevant. This was noted in the
commit log of fee29b05bb:
The root filesystem location is passed to the kernel by a partition
UUID, so it is possible to boot on QEMU, directly from the disk image,
or dump the image to a physical device.
Fixes: #11841
Cc: Pete Morici <pmorici@dev295.com>
Cc: Carlos A. M. dos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Very similar to orangepi-zero, except that the board has a 16MB SPI flash, a
2nd ethernet port is provided through a Realtek RTL8152 and wifi is provided
through a Realtek RTL8189FTV (no mainline driver, not supported).
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Default value of CONFIG_SYS_BOOTM_LEN in u-boot causes board reset for
large uImage files, so add u-boot patch to increase the maximum kernel
image size.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The readme.txt would contain similar content for either processor
family, so this patch consolidates the usage and adds the new
T2080 notes.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add Andes 32-bit defconfig for AE3XX platform.
Signed-off-by: Che-Wei Chuang <cnoize@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
Signed-off-by: Nylon Chen <nylon7@andestech.com>
[Thomas:
- fix commit title to match the defconfig name
- use the external toolchain package]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Default value of CONFIG_SYS_BOOTM_LEN in u-boot causes board reset for
large uImage files, so add u-boot patch to increase the maximum kernel
image size.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch enables the inclusion of the Pi's overlays. Previously
the overlays were not included in the genimage configuration.
This patch ensures overlays are included in the sdcard (when
enabled) by defaulting to the inclusion of an empty
output/images/rpi-firmware/overlays directory in genimage cfg.
The Pi's overlays are built with the following config
variables:
BR2_PACKAGE_RPI_FIRMWARE=y
BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTBS=y
BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS=y
BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
BR2_LINUX_KERNEL_IMAGE_NAME="Image"
BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="Image modules dtbs"
After building, the dtbo files are present in the
output/images/rpi-firmware/overlays directory but not added
to the sdcard because they are missing from the genimage cfg
file.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
[Arnout: fix indentation, and add comment explaining why an empty
directory is created.]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This bumps to linux/linux-headers 5.0 and u-boot version 2019.01. The
kernel patch is no longer needed, as the Device Tree for the platform
is now upstream.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use OpenSBI by default instead of riscv-pk (BBL).
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reduce the config fragment to the bare minimum to enable 32-bit
support. This means we are as close as possible to the arch
defconfig.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Convert the config to the arch defconfig plus a fragment. When this
fragment is applied we will generate the same config as we previously
did.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The old 3.4 Linux kernel used by this defconfig doesn't build with gcc
7.x.
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The update of imx-mkimage in commit
c14d92d439
broke the imx8-bootloader-prepare.sh script for i.MX8M, used in
freescale_imx8mqevk_defconfig
The updated mkimage_fit_atf.sh script in imx-mkimage now needs
a ATF_LOAD_ADDR variable, which was set to 0x00910000 for i.MX8M.
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This defconfig was added in October 2016 and was never updated since
then. It currently fails to build because U-Boot is too old and
doesn't build with host-openssl in version 1.1.x.
On February 13, 2019, the original submitter was notified, but didn't
reply, so let's remove the defconfig for this platform.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/165766194
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Linux version are changed to 4.19.16 (LTS) for all qemu defconfigs,
except for riscv. riscv defconfigs are left unchanged because they have
a custom Linux repository causing more difficulties when upgrading to
4.19 for riscv32. And for the riscv64, it has been updated recently to
Linux 4.20 by another contributor.
Patch for arm-versatile-nommu is changed into a git format
Add cache attributes for xtensa-lx60-nommu config because the commit
7bb516ca54
added a new config variable for memory cache attribute:
CONFIG_MEMMAP_CACHEATTR
All these updated configs have been built successfully.
Signed-off-by: Gerome Burlats <gerome.burlats@smile.fr>
Cc: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Configuration contains:
- building tpl, spl and u-boot (forked u-boot repository)
- booting from SD card and network via PXE
- working ethernet, usb and uart
- minimal rootfs with busybox
- ready to flash SD card image
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since all EFI-based systems support GPT, this commit changes
pc_x86_64_efi to use a GPT partition table. It shows an example of how
to craft a disk image with GPT partitioning instead of MBR. This is
achieved by means of a post-image script which uses
mkdosfs+mcopy+sfdisk, since genimage is unable to deal with GPT. Long
term, it would be ideal if genimage had GPT support, but until then,
this script shows how to achieve creating a GPT-based disk image.
The script was kept as simple as possible to make it easy to understand
and adapt for other purposes.
The root filesystem location is passed to the kernel by a partition
UUID, so it is possible to boot on QEMU, directly from the disk image,
or dump the image to a physical device.
Signed-off-by: Carlos Santos <casantos@datacom.com.br>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
qemu_aarch64_virt_defconfig (implicitly) specifies cortex-a53, so adjust the
QEMU command line to also emulate a a53 instead of a57.
Also adjust the defconfig to explicitly specify a53 for consistency/clarity.
Signed-off-by: Gerome Burlats <gerome.burlats@smile.fr>
Cc: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Since riscv64 works with linux default defconfig, this patch drop custom config.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
Tested-by: Mark Corbin <mark.corbin@embecosm.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot and kernel to their latest releases.
Remove the documented limitations. Recent kernels added support for the
SOM SPI flash, and the carrier SFP port.
Mention the 'dd' command in the warning text. No script is involved.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Before this commit, the grub configuration file was copied to the
TARGET_DIR in a post-image hook, after the filesystem has been
generated. It was kinda working because the board/pc's grub
configuration and the default one are the same and the later was
copied during the build process of the grub2 package.
This commit ensures the custom board/pc grub configuration is copied at
the right time.
Signed-off-by: Grégoire Delattre <gregoire.delattre@gmail.com>
Reviewed-by: Matt Weber <matthew.weber@rockwellcollin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This updates LEGO MINDSTORMS EV3 to Linux kernel 4.19 and U-Boot
2018.11. This kernel brings Bluetooth support, so some Bluez packages
are also added. Also, we now have proper device tree support, so a few
things are rearranged in the flash and SD card images since the DTB is
no longer appended to the kernel image.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The first stage bootloader on LEGO MINDSTORMS EV3 only loads the first
256K of the flash memory (this is hard-coded in an EEPROM). So, the
second stage bootloader (U-Boot) cannot exceed this size.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
NXP U-Boot tree has the following build issue:
MKIMAGE u-boot-dtb.imx
Error: No BOOT_FROM tag in board/freescale/mx7dsabresd/imximage.cfg.cfgtmp
arch/arm/imx-common/Makefile:91: recipe for target 'u-boot-dtb.imx' failed
make[2]: *** [u-boot-dtb.imx] Error 1
Makefile:877: recipe for target 'u-boot-dtb.imx' failed
This issue has been fixed by commit f916757300c1 ("imx: Create
distinct pre-processed mkimage config files"), so backport this
commit to the NXP U-Boot tree in order to fix the build error.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/136980027
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch updates the csky custom external toolchain to fix a broken
host dependency of gdb on libexpat.so.0 (most hosts now ship
libexpat.so.1). gdb is required to copy and and boot the kernel (see
board/csky/readme.txt). The updated gdb no longer has this host
dependency, which solves the issue.
Since this external toolchain was built and tested with csky kernel
4.9.56, this patch also updates to that kernel version.
Finally, this 4.9.56 csky kernel changed its default bootargs. So we
add a patch to preserve the same behavior as the previous version.
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Orangepi lite2 board has AP6356S WiFi/BT combo, but does
not have ethernet port. So it makes sense to enable wireless
networking by default:
- add broadcom wireless firmware package to image
- add basic wireless tools to image
- add rootfs overlay with proper NVRAM file for on-board AP6356S chip
- add mdev to image to enable module autoloading
- update readme.txt to test wifi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Orangepi Lite2 board with below features:
- U-Boot 2018.09
- Linux 4.19.0-rc8
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Orangepi One Plus board with below features:
- U-Boot 2018.09
- Linux 4.19.0-rc8
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently, U-Boot is failing to build, due to some issues
with the toolchain and the U-Boot port.
Fix it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
New generic defconfig for aarch64, to run on aarch64 servers compliant
with EFI firmware and ACPI.
This can also be tested with qemu, and is useful so that we have an
arm defconfig with grub enabled. Tested with qemu 2.11.2 and AAVMF,
the aarch64 virtual machine UEFI firmware.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
[Thomas: extend readme.txt with more details]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
4.18 brought cpufreq support for H3, but sunxi_defconfig does not enable the
ondemand cpufreq govenor so the frequency is dynamically adjusted - So
enable it in linux-extra.config.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
4.18 brought cpufreq support for H3, but sunxi_defconfig does not enable the
driver for the sy8106a regulator used on the board or enable the ondemand
cpufreq govenor so the frequency is dynamically adjusted - So enable these in
linux.fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The default ORC unwinder requires libelf to be built. While we could
build libelf using BR2_LINUX_KERNEL_NEEDS_HOST_LIBELF, we probably
don't really need the ORC unwinder in the PC defconfigs, so let's use
the frame pointer unwinder instead.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/123771107
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the kernel and U-Boot versions to the actual versions in use.
Update the description of supported hardware features.
Add a note that the stale SPI flash environment issue only affects the
vendor BSP.
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to version 2018.11. This version supports autodetection of
SD/eMMC boot source, so we can now enable environment load from SD card.
Add a U-Boot kconfig fragment that sets SD/eMMC as environment load/save
device. This avoids stale environment values from the SPI flash. That in
turn, allows to use the more convenient distro boot which is enabled in
the default environment.
Bump kernel to version 4.19.2. This version enables
CONFIG_PHY_MVEBU_CP110_COMPHY in the arm64 defconfig, so remove it from
the kernel kconfig fragment. Enable support for SFP modules detection
and configuration. Leave the PHY drivers for now to keep them built into
the kernel. The kernel defconfig builds these drivers as modules. But
that does not work as expected in the default configuration.
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Amarula A64-Relic board has AP6330 WiFi/BT combo, but does
not have ethernet port. So it makes sense to enable wireless
networking by default:
- add broadcom wireless firmware package to image
- add basic wireless tools to image
- add rootfs overlay with proper NVRAM file for on-board AP6330 chip
- add mdev to image to enable module autoloading
- update readme.txt to test wifi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Amarula A64-Relic board
with below features:
- U-Boot 2018.07
- Linux 4.17.0-rc6
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas: add missing BR2_TARGET_UBOOT_NEEDS_PYLIBFDT=y and
BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y options.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Some ZynqMP device trees in the kernel have a dot in their name,
for example "zynqmp-zcu102-rev1.0". The post image script
left out the part after the dot and created an invalid symlink.
Signed-off-by: Francois Beerten <fbeerten.git@colabti.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch provides support for the board Odroid XU4. It uses a recent
4.14 kernel released by Hardkernel, and the current u-boot 2017.05
also from Hardkernel.
Signed-off-by: Pierre CROKAERT <pct@crookies.net>
[Thomas:
- Update DEVELOPERS file
- Update .gitlab-ci.yml file
- Simplify the boot.ini script
- Add missing BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_14 option
- Add BR2_PACKAGE_HOST_DOSFSTOOLS and BR2_PACKAGE_HOST_MTOOLS since a
VFAT filesystem is generated
- Keep the default root filesystem size, since it is sufficient.
- Reduce the size of the VFAT filesystem]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add intial support for Bananapi M2 Ultra board based on the Allwinner
R40 SoC.
- U-Boot 2018.07
- Linux 4.18.12
Board specifications: http://www.banana-pi.org/m2u.html
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add RISC-V 64-bit defconfig for QEMU virt machine.
Tested with QEMU 2.12.1
Signed-off-by: Mark Corbin <mark.corbin@embecosm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit renames olimex_a20_olinuxino_lime_mali to
olimex_a20_olinuxino_lime_legacy, because the upstream Linux kernel
now also supports using the Mali GPU.
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch removes duplicate messages in Linux log on HSDK board.
For HSDK board we setup bootargs via device tree,
see https://elixir.bootlin.com/linux/latest/source/arch/arc/boot/dts/hsdk.dts#L25
"console=ttyS3" was mistakenly placed in u-boot bootargs which are
appended to Kernel bootargs in case of using buildin .dtb.
Before patch log is like:
------------------------8<-------------------------------------
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz,...
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz,...
mmc0: new SDHC card at address 59b4
mmc0: new SDHC card at address 59b4
blk_queue_max_segment_size: set to minimum 8192
blk_queue_max_segment_size: set to minimum 8192
------------------------>8-------------------------------------
After patch log is like:
------------------------8<-------------------------------------
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz,...
mmc0: new SDHC card at address 59b4
blk_queue_max_segment_size: set to minimum 8192
------------------------8<-------------------------------------
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Resurrect support for RIoTboard after 2018.02.x deprecation.
Signed-off-by: Nikolay Dimitrov <nikolay.dimitrov@retrohub.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
At first the support for i.MX8MQ processors was minimal, hence this
section in the readme file.
Since then, GPU support was added [1] in master and VPU in next [2].
So drop this section as it is confusing people and no one maintains it.
[1] https://git.buildroot.net/buildroot/commit/?id=84afda9c
[2] https://git.buildroot.net/buildroot/commit/?id=82732071
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
512B is not a correct size to express "512 bytes", and causes a
genimage failure:
ERROR: Invalid size suffix 'B' in '512B'
To express "512 bytes", using just "512" is sufficient. With this
commit, genimage works fine, and we indeed have a 512 bytes unused
partition:
$ fdisk -l output/images/sdcard.img
Disk output/images/sdcard.img: 60 MiB, 62915584 bytes, 122882 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x00000000
Device Boot Start End Sectors Size Id Type
output/images/sdcard.img1 1 1 1 512B 0 Empty
output/images/sdcard.img2 2 524289 524288 256M 83 Linux
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/88314963
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
As for sh4-r2d (little-endian) restore the old sh-sci driver behaviour
for sh4eb-r2d.
Tested with qemu_sh4eb_r2d_defconfig.
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This reverts commit 18e8cf159177100e69d528293f8cf6875c0b1bca (kernel)
The last Qemu kernel update [1] introduced a regresion in sh4 SCIF
serial device. Some keyboard presses are very slow to be taken into
account, perhaps not even taken into account at all. This would
explain why our test infrastructure doesn’t manage to login as root
[2][3][4].
git bisect reported a kernel patch from 4.11, increasing RX FIFO
trigger defaults value for sh-sci (H)SCIF. The kernel patch itself
looks good but the Qemu emulation is not ready to handle this new
setting.
>From Qemu (2.12.0): target/sh4/README.sh4
"Configuration of the second serial port (SCIF) is supported. FIFO
handling infrastructure has been started but is not completed yet."
We can't use the first serial port (ttySC0) because it's the second
SH UART that's emulated by Qemu.
In order to be able to test sh4 architecture with newer kernel,
revert to the old behaviour.
[1] 03fb00f217
[2] https://gitlab.com/free-electrons/toolchains-builder/-/jobs/72006425
[3] https://gitlab.com/free-electrons/toolchains-builder/-/jobs/72006427
[4] https://gitlab.com/free-electrons/toolchains-builder/-/jobs/72006426
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
U-Boot SPL configures pinmuxes, clocks and other low-level devices. On
the Xilinx ZynqMP SoCs the code to do this resides in a file called
psu_init_gpl.c which is initially generated by the Xilinx development
tools. Add an option to pass these files from the outside (e.g. in the
board files).
For this to work properly, a patch to U-Boot is needed. However this
patch must be applied by each defconfig using
BR2_TARGET_UBOOT_ZYNQMP_PSU_INIT_DIR. If it were in boot/uboot/ to be
applied unconditionally, it would break the build for configs using a
U-Boot version where the patch is already applied.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Reviewed-by: Joel Carlson <JoelsonCarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
[Thomas: add comment about U-Boot version requirements to use this
option.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This adds support the Xilinx ZCU106 development board.
[Tested on the ES2 (Engineering Sample 2) version of the board]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
In order to boot on the Xilinx ZynqMP SoCs, U-Boot SPL requires a
recent PMU firmware loaded. Instruct U-Boot to add pmufw.bin to the
boot.bin file together with U-Boot SPL, and the boot ROM will load
both.
For this to work properly, a patch to U-Boot is needed. However this
patch must be applied by each defconfig that wishes to use
BR2_TARGET_UBOOT_ZYNQMP_PMUFW. If it were in boot/uboot/ to be applied
unconditionally, it would break the build for configs using a U-Boot
version higher than 2018.7-rc1 where the patch is already applied.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Reviewed-by: Joel Carlson <JoelsonCarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
[Thomas:
- indicate that this feature requires U-Boot 2018.07, since commit
c7df098a71e05dc81cee818747759e8060b59626 is needed.
- define UBOOT_ZYNQMP_KCONFIG_PMUFW only once, and instead use a
variable named UBOOT_ZYNQMP_PMUFW_PATH to store the path to the PMU
firmware]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Use proper ARCH for mkimage command
- Use different U-Boot binary name depending on ARCH
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
6x_bootscript/6x_upgrade have been deprecated for more than a year.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The upgrade.cmd script expects the binary to be named
u-boot.<uboot_defconfig>.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Allow user to override the hardcoded dtb name by using
BR2_ROOTFS_POST_SCRIPT_ARGS.
The only user of this script, configs/freescale_imx8mqevk, is updated
accordingly.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for flashing the u-boot-dtb.imx binary in the SD card
when a target selects BR2_TARGET_UBOOT_FORMAT_DTB_IMX.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The 2017 MinnowBoard Turbot skews no longer use the Realtek 8169
Ethernet chip. The Turbot D0 uses The Intel I211, the Turbot Dual
Ethernet has an I210 (quad-core) or I211 (dual-core).
Add CONFIG_IGB to the Linux config but keep the Realtek 8169 support
to avoid breaking older boards
Tested on Turbot D0, lspci -k shows the igb driver is used:
03:00.0 Class 0200: 8086:1539 igb
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add a defconfig for the Olimex A10-OLinuXino-LIME, reusing most
of the A20-OLinuXino-Lime and A13-OLinuXino files (sym links).
The configurations for Olimex A10-OLinuXino-LIME feature:
- U-Boot 2018.03
- Mainline Linux kernel 4.14.26
Signed-off-by: Leon Anavi <leon.anavi@konsulko.com>
[Arnout: remove commented-out BR2_ARM_EABIHF=y (which is default)]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
As per latest Raspberry Pi firmware documentation, the option
'arm_control' has been deprecated in favor of 'arm_64bit'.
Fixes https://bugs.busybox.net/show_bug.cgi?id=11111.
Signed-off-by: Jason Tang <tang@jtang.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the kernel version to 4.17.2.
Update U-Boot version to 2018.05.
Migrate to U-Boot generic distro configuration which is easier than the
hand written boot script.
Improve the 'dd' command example in readme.txt.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
To not maintain custom copy of inittab file lets adopt approach
used in raspberrypi adding post-build script for synopsys/axs10x
boards.
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Apply modifications made in recent commits:
- 456ea9871e busybox: add /dev/std{in, out, err} symlinks to inittab
- 13dbe73782 busybox: reduce number of mkdir calls in inittab
- 8a89d290d4 busybox: add an inittab entry to activate swap
Signed-off-by: Carlos Santos <casantos@datacom.com.br>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
4.17 brings support for HDMI out, but sunxi_defconfig hasn't been updated to
enable the drivers - So add a kernel fragment to enable them.
Likewise, analog audio has been supported since 4.10, but the driver isn't
enabled in sunxi_defconfig, so enable it in the fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump kernel to version 4.17 and U-Boot to 2018.05.
As the dtb file has been renamed in mainline, make the necessary
adjustments in U-Boot environment and also in
BR2_LINUX_KERNEL_INTREE_DTS_NAME.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump kernel to version 4.17 and U-Boot to 2018.05.
As the imx_v6_v7_defconfig in 4.17 already selects the
CONFIG_CFG80211_WEXT option, the linux.fragment can
be simply removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump linux as well headers to v4.16 version, this eventually drop the
wifi patch since it has been merged to Linux v4.16.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
All linux configs are renamed to a version neutral filename
to avoid further renaming on kernel bumps.
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.16.7 2.12.0 YES OK
arm_versatile 4.16.7 2.12.0 YES OK
arm_versatile_nommu 4.16.7 2.12.0 YES OK (3)
arm_vexpress 4.16.7 2.12.0 YES OK
m68k_mcf5208 4.16.7 2.12.0 YES OK
m68k_q800 4.16.7 q800-v2.11.0 NO (2) OK
microblazebe 4.16.7 2.12.0 YES OK
microblazeel 4.16.7 2.12.0 YES OK
mips32r2el_malta 4.16.7 2.12.0 YES OK
mips32r2_malta 4.16.7 2.12.0 YES OK
mips32r6el_malta 4.16.7 2.12.0 YES OK
mips32r6_malta 4.16.7 2.12.0 YES OK
mips64el_malta 4.16.7 2.12.0 YES OK
mips64_malta 4.16.7 2.12.0 YES OK
mips64r6el_malta 4.16.7 2.12.0 YES OK
mips64r6_malta 4.16.7 2.12.0 YES OK
nios2-10m50 4.16.7 2.12.0 NO OK
or1k 4.16.7 2.12.0 NO OK
ppc_g3beige 4.16.7 2.12.0 YES OK
ppc_mpc8544ds 4.16.7 2.12.0 YES OK
ppc_virtex_ml507 4.16.7 2.12.0 NO OK
ppc64_pseries 4.16.7 2.12.0 YES OK
ppc64le_pseries 4.16.7 2.12.0 YES OK
ppc64_e5500 4.16.7 2.12.0 YES OK
sh4 4.16.7 2.12.0 YES OK
sh4eb 4.16.7 2.12.0 NO (1) OK
sparc_ss10 4.16.7 2.12.0 YES OK
sparc64_sun4u 4.16.7 2.12.0 YES OK
x86 4.16.7 2.12.0 YES OK
x86_64 4.16.7 2.12.0 YES OK
xtensa_lx60 4.16.7 2.12.0 YES OK
xtensa_lx60_nommu 4.16.7 2.12.0 YES OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Kernel patch required, switched to devicetree usage
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
RK3288 Vyasa board support falcon mode in U-Boot and SD layout start from
16MB offset for args and 17MB for uImage. So give full u-boot partition
space as 30M so-that it can occupy bigger uImage file and doesn't overlap
rootfs partition.
[Peter: use # as comment character, clarify comment wording]
Reported-by: Shyam Saini <shyam@amarulasolutions.com>
Tested-by: Shyam Saini <shyam@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shyam saini <shyam@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The kernel now includes the rpi3b+ device tree for aarch64
Signed-off-by: Martin Bark <martin@barkynet.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With this commit we update u-boot version to 2018.05 for
Synopsys boards. U-boot version 2018.05 was released recently
and includes significant changes for ARC boards:
* Fix for compile-time warning for AXS10x
* Add support of platform-specific commands for HSDK
* Add support for on-board SPI flash on HSDK
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use "i.MX8MQ" (in capital letters) for the SoC name for better
readability.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Improve the documentation by adding the configuration of SW801 and SW802
switches for SD card boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently this target fails to build:
arch/arm/mach-imx/built-in.o: In function `init_mmdc_lpddr2_settings':
platform-spi_imx.c:(.text+0x8f18): undefined reference to `imx6sll_lpddr2_freq_change'
arch/arm/mach-imx/built-in.o: In function `imx6ul_cpuidle_init':
platform-spi_imx.c:(.init.text+0x195c): undefined reference to `mx6ull_lpm_wfi_end'
platform-spi_imx.c:(.init.text+0x1960): undefined reference to `mx6ull_lpm_wfi_start'
platform-spi_imx.c:(.init.text+0x1964): undefined reference to `imx6ull_low_power_idle'
arch/arm/mach-imx/built-in.o: In function `imx6sl_init_late':
platform-spi_imx.c:(.init.text+0x56f0): undefined reference to `imx6sll_cpuidle_init'
Makefile:969: recipe for target 'vmlinux' failed
NXP 4.9 kernel does not properly support mx31, so better remove this target.
mx31_3stack board is currently supported in U-Boot and kernel mainline,
so if someone is interested on this board, then a target can be introduced
later which uses these mainline components.
Currently I do not have access to this board, so remove it its defconfig
for now.
Fixes: https://gitlab.com/buildroot.org/buildroot/-/jobs/66561688
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As we are about to remove the Blackfin architecture, remove the only
defconfig that was using this CPU architecture.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit adds a genimage template file that is used for i.MX8
platforms in the common i.MX post-image script.
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit adds an imx8-bootloader-prepare.sh script that will be
used by i.MX8 platforms to prepare their bootloader image.
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit makes the common post-image.sh script used by Freescale
platforms compatible with arm64:
- Support having DTBs in sub-folders
- Support a kernel image in the 'Image' format
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adds support for the at91sam9g20-ek board to the flasher.sh script.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support to the flasher.sh script for the at91sam9260-ek board which
complements the existing at91sam9260eknf_defconfig.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Instead of using the install of sam-ba under host/opt directly, use the symlink
created in host/bin. The side effect of doing this instead allows the correct
sam-ba binary to be used based on the host arch being 32 bit or 64 bit.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Resolves an error in the way the bootlin toolchain-builder uses
the board/qemu/ppc64-e5500/readme.txt to generate the qemu test
command.
https://github.com/free-electrons/toolchains-builder/blob/master/build.sh#L186
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Switch to Linux kernel version 4.9.59 from the TI SDK 04.02.00.09
(TI SDK release date: 23.12.2017)
Updated uboot to version 2018.01
uEnv.txt corrected to boot from sd card on the ti-am335x-evm
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adding basic support modeled after the Freescale/NXP T1040RDBD4 board.
This target is used to support testing of the bootlin e5500 toolchain.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
[Thomas: update .gitlab-ci.yml.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
My goal was to rely on upstreamed features as much as possible, which
means that some bits are only half-baked for now:
- Due to the DTS restructuring in upstream kernel, we require 4.11+. The
latest LTS or CIP kernels do not know about the -Base model.
- Linux has no generic support for SFP cages (yet). It seems that this
has hit the net-next tree in August 2017, but there's been no release
(it's probably targettting 4.14). Also, the merge only included the
required infrastructure; the mvneta driver conversion is not included.
Patches which finalize this exist in Russel King's tree and also in
random vendor trees.
- There's no access to the SPI flash in these versions of
uboot/linux/dts.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
[Arnout:
- rename to solidrun_clearfog_defconfig;
- specify kernel headers version (default is now 4.15);
- remove ext2 fs size override, the 4 extra MB are not needed;
- U-Boot needs dtc and openssl;
- add comments to defconfig;
- update .gitlab-ci.yml;
- mention in readme.txt that SFP support is missing;
- add Jan to DEVELOPERS.
]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Synopsys DesignWare HSDK (which stands for ARC HS
Development Kit) is the latest and greatest development
platform that sports quad-core ARC HS38 in real silicon.
Most noticeable features of the board are:
* Quad-core ARC HS38 CPU running at 1GHz
* 4Gb of DDR
* Built-in Vivante GPU (well supported via open source
Etnaviv drivers)
* Built-in Wi-Fi/Bluetooth module (RedPine RS-9113)
And as usual we have:
* [micro] SD-card slot
* 2 USB 2.0 ports
* 1Gbit Ethernet port
* Built-in Digilent JTAG probe
* Serial port accessible via micro-USB port
Writing sdcard.img on SDcard creates two partitions:
* FAT32 with uImage and uboot.env
* EXT4 with root filesystem
We modify kernel config because in default hsdk kernel config
CONFIG_INITRAMFS_SOURCE parameter is set and when we build
rootfs separately (BR2_TARGET_ROOTFS_INITRAMFS is not set)
error appears. Also we set up CONFIG_ARC_UBOOT_SUPPORT which
enables usage of uboot variables in the boot process.
[Peter: Fix comments and rename defconfig to snps_archs38_hsdk_defconfig,
Add defconfig to DEVELOPERS and fixup board/synopsys entry,
Drop postimage script, rename env file in genimage.cfg and drop size
setting for rootfs partition,
Add "" for CONFIG_INITRAMFS_SOURCE in linux fragment]
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-buildroot@synopsys.com
Reviewed-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Up to now, Raspberry Pi Zero W (rpi0w) could be built with the normal
raspberrypi0_defconfig. However, then you don't have support for the
Bluetooth out-of-the-box, which makes using a W a bit pointless.
Therefore, create a separate defconfig for the W. It is a copy of
raspberrypi0_defconfig with the following changes:
- Add DT overlays (from rpi-firmware) to support Bluetooth.
- Pass --add-pi3-miniuart-bt-overlay to post-image.sh.
Since there is now a separate raspberrypi0w_defconfig, the W support
can be removed from raspberrypi0_defconfig.
Signed-off-by: Yves Deweerdt <yves.deweerdt.linux@gmail.com>
[Arnout:
- Bump to same kernel version as raspberrypi0.
- Remove redundant comment.
- Remove redundant default BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS=y.
- Improve commit log.
- Refresh .gitlab-ci.yml.
]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
The uCLS1012A-SOM product family (ucls1012a) is an Arcturus Networks Inc.
64bit ARM Cortex-A53 class System on Module powered by a NXP QorIQ LS1012A
Low Power Communication Processor. This 314 pin MXM3.0/SMARC module card
contains DDR3, QSPI NOR Flash, eMMC NAND Flash, optional Audio CODEC and is
available with 1 or 2 Gig-Ethernet PHYs.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Changes v1 -> v2:
- updated kernel and u-boot source repositories to github
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Sometimes imximage throws the following error:
MKIMAGE u-boot-dtb.imx
Error: No BOOT_FROM tag in board/freescale/mx6sxsabresd/imximage.cfg.cfgtmp
arch/arm/imx-common/Makefile:91: recipe for target 'u-boot-dtb.imx' failed
Later on, when running mkimage for the u-boot.imx it will succeed in
finding the IVT offset.
Looks like some race condition happening during parallel build when
processing mkimage for u-boot-dtb.imx and u-boot.imx.
A proper fix still needs to be implemented, but as a workaround let's
remove the error when the IVT offset is not found.
It is useful to have such message, especially during bring-up phase,
but the build error that it causes is severe, so better avoid the
build error for now.
The error checking can be re-implemented later when we have a proper
fix.
This workaround has already been applied in mainline U-Boot:
http://git.denx.de/?p=u-boot.git;a=commit;h=b5b0e4e351e20a606de22db6a56ad6bc1e2aa8fd
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/59015347
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The T1 QoriQ from NXP has had a few varients of RDB dev boards.
This target is against the latest D4RDB version. Any of the
other versions before D4RDB (plain RDB), may require backing off
the uboot version to SDK 1.6 and/or adjusting the kernel dtb used.
This board configuration provides an upstream kernel build which
has been verified to boot on target.
The target assumes the user still uses the NXP suggested prebuilts
in the SDK2.0 (last release for PowerPC). If a uboot rebuild is
required, the source for SDK2.0 can be found in the following repo.
http://git.freescale.com/git/cgit.cgi/ppc/sdk/u-boot.git/tag/?id=fsl-sdk-v2.0-1703
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Replacing the p1010rdb, this board is based on the tower development
system still available by NXP. The board is setup to track upstream
Linux and has been bumped from 4.1 to 4.15 (compared to p1010).
The target does not build uboot and assumes the user still uses the NXP
suggested prebuilts in the SDK2.0 (last release for PowerPC). If a
uboot is required, the source for SDK2.0 can be found in the following
repo.
http://git.freescale.com/git/cgit.cgi/ppc/sdk/u-boot.git/tag/?id=fsl-sdk-v2.0-1703
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Rename the confusing and misleading ts5x00 directory to a real reference
platform name, ts5500. The readme.txt file already states the support
for both TS-5500 and TS-5400 platforms.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump the 3.17 kernel used for the Technologic Systems TS-5500 platform
to the latest LTS kernel 4.14.
This fixes the ts5x00_defconfig build with GCC 6.x.
The linux-3.17.config file has been renamed to linux-4.14.config to
match the new kernel version, and its changes are the result of make
linux-update-defconfig. However only comments are affected.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig fails to build with gcc 6.x, even though we switched to
using gcc 6.x as the default gcc version in May 2017.
This defconfig also hasn't seen any non-mechanical update since
November 2015.
So it's time to get rid of it, in order to remove the following build
failure:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306938
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig fails to build with gcc 6.x, even though we switched to
using gcc 6.x as the default gcc version in May 2017.
It hasn't been updated since April 2017, and the original submitter,
Fabio Porcedda said:
Unfortunately a newer kernel doesn't boot and I don't have the time
to fix the issue. If having a defconfig that doesn't build on gcc
6.x is unacceptable feel free to remove it.
So, let's get rid of this defconfig, which will remove the following
build error:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306952
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Wireless support ends up enabling CONFIG_SYSTEM_TRUSTED_KEYRING, which
requires openssl to be available on the host, so disable wireless
support, which isn't needed in Qemu.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The ORC unwinder requires libelf to be available on the host, so use
the frame pointer unwinder instead. Using the frame pointer unwinder
is probably good enough in our default Qemu configurations.
Wireless support ends up enabling CONFIG_SYSTEM_TRUSTED_KEYRING, which
requires openssl to be available on the host, so disable wireless
support, which isn't needed in Qemu.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig currently doesn't build with GCC6 (Linux 4.1).
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306827
A maintainer w/board isn't available to make updates, so removing
this config.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
>From the original submitter of this defconfig:
"""
I no longer have access to ci40 board. It would be difficult for me to
maintain it.
"""
And this defconfig currently fails to build with gcc 6.x. Therefore,
drop it.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306806
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
No other changes necessary, 4.15 builds and boots fine.
Signed-off-by: Alex Suykov <alex.suykov@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig currently fails to build the Linux kernel:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306826
In addition, the U-Boot build had already been removed in commit
12c01e4a05
("configs/freescale_mpc8315erdb: remove U-Boot build"), back in
October 2016, and nobody bothered fixing it.
This defconfig was originally contributed and maintained by Gustavo
Zacarias, but he is no longer active in Buildroot, and nobody
expressed interest in this defconfig, so let's get rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
In particular:
- Explicitly specify the CPU to be used, POWER8, which matches
qemu_ppc64le_pseries_defconfig
- Use hard disk emulation to access the root filesystem instead of an
initrd.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This allows the toolchain building machinery used by
https://toolchains.bootlin.com to automatically re-use this Qemu
command line.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
qemu-system-ppc64le doesn't necessarily exist: it isn't installed by
Qemu, and only created as a symlink to qemu-system-ppc64 by some
distributions (Ubuntu). Other distributions (Fedora) just have
qemu-system-ppc64.
But qemu-system-ppc64 is capable of running little-endian PPC64
systems, so use this one instead.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Orange-Pi Zero Plus2 board has AP6212 WiFi/BT combo, but does
not have ethernet port. So it makes sense to enable wireless
networking by default:
- add DTS patch enabling AP6212 WiFi/BT combo support
-- this patch is on its way to mainline Linux v4.16
- enable WiFi support in kernel config
- enable Broadcom brcmfmac kernel driver in kernel config
- add Broadcom wireless firmware package to image
- add basic wireless tools to image
- add mdev to image to enable module autoloading
- add rootfs overlay with proper NVRAM file for on-board AP6212 chip
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump versions:
- use U-Boot 2008.01
- use Linux kernel v4.15.2
Drop patch with dts sdcard fix since it has been
merged to Linux v4.15.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With this commit we update Linux kernel version to 4.15 and
Linux headers version to 4.15.
Also patches for arc vdk are removed because these
changes were applied in Linux 4.15.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump Linux to 4.15 and U-Boot to 2018.01. Remove networking dts patches
since they has landed in Linux 4.15. Update readme.txt: fix mainline BSP
versions and update boot selection for board rev 1.3.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add a genimage.cfg to create a working sdcard.img for the ci20
hardware. We also need a uboot-env.txt to create the partition for
the uboot environment.
Update the board/ci20/readme.txt with the related information. Remove
the tftp netboot description from the readme as it is already to
complicated for a basic bootable example.
Signed-off-by: Johannes Schmitz <johannes.schmitz1@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Currently in Orange Pi boards post-build script is used only to generate
U-Boot boot script and post-image script is used only to generate sdcard
image according to genimage configuration. However both those tasks can
now be handled by generic Buildroot tools:
- BR2_TARGET_UBOOT_BOOT_SCRIPT config options
- support/scripts/genimage.sh script
This patch drops custom scripts replacing them
by generic Buildroot tools.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also include new boot scripts to match standard distro uboot commands.
Our previous 6x_bootscript and 6x_upgrade used custom variables and
their naming don't make sense now that we target more than i.MX6 CPU.
Therefore those old scripts are marked as legacy and kept for now but
the goal is to deprecate and remove them later.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also switch repository from old freescale site to codeaurora:
https://source.codeaurora.org/external/imx/
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Orangepi PC2
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Zero Plus2
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Prime
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Win/Win Plus
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Olimex A64-OLinuXino
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Tsvetan Usunov <usunov@olimex.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for FriendlyARM Nanopi NEO2 board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Yuefei <yftan@friendlyarm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for FriendlyARM Nanopi A64
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Yuefei <yftan@friendlyarm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for SoPine board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: TL Lim <tllim@pine64.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Pine64 board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: TL Lim <tllim@pine64.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for bananapi M64 board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Jason <manager@sinovoip.com.cn>
Cc: hailymei@banana-pi.com <hailymei@banana-pi.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add MacchiatoBin board by SolidRun. This board is based on Marvell
Armada 8040 SoC. Board support package includes the following
two options: mainline and vendor BSPs.
Mainline BSP:
- Marvell ATF v1.3-armada-17.10
- mainline U-Boot v2017.11
- mainline Linux kernel v4.14.4
Marvell BSP with more hardware support enabled:
- Marvell ATF v1.3-armada-17.10
- Marvell U-Boot based on v2017.03
- Marvell Linux kernel based v4.4.52
More details about this board are available on wiki:
- http://wiki.macchiatobin.net
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
[Thomas: misc tweaks in readme.txt.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Run-time tested on ZedBoard, build-tested on the other boards]
[Peter: also add host-dosfstools / host-mtools to make vfat images]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
We are about to introduce genimage support for the Zynq boards. For
all of them U-Boot loads the DTB from a file named "devicetree.dtb" so
we need to rename it on the SD card image.
We could use genimage itself to rename files while creating the
image. But this would require a different genimage.cfg for each board,
leading to duplicate code.
Instead let's create a "devicetree.dtb" symlink pointing to the dtb
listed in the configuration. Currently all the Zynq-based boards have
only one DTS configured, but if one had two or more of them, the
symlink would point to the first one.
[Peter: only create symlink if dtb option is available]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This board is quite similar to orangepi-one board. Instead of ethernet, it
has RTL8189FTV SDIO WiFi chip.
Board support package includes the following components:
- mainline u-boot 2017.09
- mainline kernel 4.13.11
Signed-off-by: Jan Kraval <jan.kraval@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This board is a variant of orangepi-pc board. It adds 8GB eMMC and Realtek
RTL8189FTV SDIO WiFi chip. This variant has a separate support in U-Boot
and kernel. So it makes sense to create a separate entry
for this board in buildroot.
Board support package includes the following components:
- mainline u-boot 2017.09
- mainline kernel 4.13.11
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
[Thomas: add entry to DEVELOPERS file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This merges the next branch accumulated during the 2017.11 release
cycle back into the master branch.
A few conflicts had to be resolved:
- In the DEVELOPERS file, because Fabrice Fontaine was added as a
developer for libupnp in master, and for libupnp18 in
next. Resolution is simple: add him for both.
- linux/Config.in, because we updated the 4.13.x release used by
default in master, while we moved to 4.14 in next. Resolution: use
4.14.
- package/libupnp/libupnp.hash: a hash for the license file was added
in master, while the package was bumped into next. Resolution: keep
the hash for the license file, and keep the hash for the newest
version of libupnp.
- package/linux-headers/Config.in.host: default version of the kernel
headers for 4.13 was bumped to the latest 4.13.x in master, but was
changed to 4.14 in next. Resolution: use 4.14.
- package/samba4/: samba was bumped to 4.6.11 in master for security
reasons, but was bumped to 4.7.3 in next. Resolution: keep 4.7.3.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Or1k support improved, f.e. musl can be tested inside qemu.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This helps the toolchains.free-electrons.com build logic re-use
directly the Qemu command lines from this readme.txt file, by having a
-append option similar to the ones used in other readme.txt files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This helps the toolchains.free-electrons.com build logic re-use
directly the Qemu command lines from this readme.txt file, by having a
-append option similar to the ones used in other readme.txt files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6ulevk_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As there is now a defconfig inside kernel sources for mxs platforms, use it.
Signed-off-by: Julien BOIBESSOT <julien.boibessot@armadeus.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This updates the LEGO MINDSTORMS EV3 board to Linux kernel 4.14 and
U-Boot 2017.11.
* Kernel patches are dropped because they are in mainline now.
* This caused the kernel image to be >3M so some adjustments to the image
sizes/layout needed to be made in U-Boot.
* Updated U-Boot version bumped since we are touching this config anyway
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6sx-sdb_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6slevk_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
boot.cmd using dts file instead of dtb which was
added in below commit, so fix the same.
"board: Add Bananapi M1 support"
(sha1: 5f50fb8d1d)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add some documentation about running the pc defconfigs in qemu.
In particular, document the use of the -bios parameter to use the OVMF
firmware to test the UEFI image.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This simplifies the pc configs and respective post image scripts to use
the shared genimage script and separate grub config files.
Separate grub files are cleaner to maintain and easier to copy and
modify, for example to support booting the pc defconfigs in qemu.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for bananapi M1 board with below features:
- U-Boot 2017.09
- Linux 4.13.7
- Default packages from buildroot
Cc: Jason <manager@sinovoip.com.cn>
Cc: hailymei@banana-pi.com <hailymei@banana-pi.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The gpu_mem option is not using the proper option argument which causes sed to
fail.
+ case "${arg}" in
+ gpu_mem=ome/gportay/output-rpi3-qtwe/images
+ sed -e '/^ome/gportay/output-rpi3-qtwe/images=/s,=.*,=ome/gportay/output-rpi3-qtwe/images,' -i /home/gportay/output-rpi3-qtwe/images/rpi-firmware/config.txt
sed: -e expression #1, char 8: extra characters after command
+ case "${arg}" in
+ gpu_mem=ome/gportay/output-rpi3-qtwe/images
+ sed -e '/^ome/gportay/output-rpi3-qtwe/images=/s,=.*,=ome/gportay/output-rpi3-qtwe/images,' -i /home/gportay/output-rpi3-qtwe/images/rpi-firmware/config.txt
sed: -e expression #1, char 8: extra characters after command
The issue comes from the use of $1 instead of $arg to extract the gpu_mem
value. $1 is the $(BINARIES_DIR) which leads to a sed expression error.
Also, it adds the error flag to the shell script to prevent from such situation
and terminate the build in error.
Signed-off-by: Gaël PORTAY <gael.portay@savoirfairelinux.com>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump the kernel to version 4.13.5 and U-Boot to 2017.09.
While at it, remove the custom scripts for generating the SD card image
and use the standard scripts instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The "virt" machine supports disk emulation, so use a ext4 rootfs instead of
initramfs for consistency with the other qemu defconfigs.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Mainline kernel is able to decode video via the coda driver.
Add support for it and also add some explanation on how VPU decoding
can be tested with Gstreamer.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Introduce imx6-sabreauto_defconfig that uses mainline U-Boot and
mainline kernel.
As mainline U-Boot supports SPL, it is possible to boot the same
sdcard.img in the three mx6sabreauto variants: imx6q, imx6dl and imx6qp.
Also update the readme.txt file to explain how to build an image for
mx6sabreauto boards using mainline U-Boot and kernel.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[Thomas: regenerate gitlab-ci.yml file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Improve the explanation of the need for using the performance governor.
This problem is specific to mx6sabresd board and the Egalax touchscreen
running a mainline kernel, so make this clear.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The parts of the readme.txt that specify the board-specific aspects
(DTB files, KMS config json file) were a bit confusing. For the DTB
files this is solved by putting the board it applies to after the DTB
file name. For the json files, this is solved by adding an extra line,
so the CinematicExperience-demo is clearly separated from the setting
of QT_QPA_EGLFS_KMS_CONFIG.
Also remove the 'for all boards' line in the beginning, it doesn't add
any value.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This patch add support for Open Frame C.TOUCH 12 Kit.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This patch add support for Open Frame C.TOUCH 10.1 Kit.
Since the defconfig is no longer only for the starter kit, remove that
from BR2_TARGET_GENERIC_ISSUE.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
