Since commit 'package/rpi-firmware: fix startup file names' ([1]) the
start and fixup file names are normalized to start.elf/fixup.dat,
adjust the rpi4 genimage config files accordingly.
Fixes:
ERROR: file(rpi-firmware/fixup4.dat): stat(.../images/rpi-firmware/fixup4.dat) failed: No such file or directory
ERROR: vfat(boot.vfat): could not setup rpi-firmware/fixup4.dat
[1] https://git.buildroot.net/buildroot/commit/?id=1bdc0334ff6273761b2e7fda730cdcc7e1f46862
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for RK3399 based rockpi-4 targets (model A, B, C)
with below features:
- Custom U-Boot 2020.07-rc4
https://github.com/amarula/u-boot-amarula.git
branch rock-pi
- Linux 5.4.46
- GPT partition layout is being used
- Default packages from buildroot
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for RK3399PRO SOM based rockpi-n10 target
with below features:
- Custom U-Boot 2020.07-rc4
https://github.com/amarula/u-boot-amarula.git
branch rock-pi
- Linux 5.7.2
- GPT partition layout is being used
- Default packages from buildroot
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
virtio-fs allow sharing a directory between the host and the guest.
It require virtiofsd daemon running before starting Qemu.
The wiki [1] recommand to enable the following kernel options:
CONFIG_VIRTIO
CONFIG_VIRTIO_FS
CONFIG_DAX
CONFIG_FS_DAX
CONFIG_DAX_DRIVER
CONFIG_ZONE_DEVICE
But virtio-fs works fine with only VIRTIO_FS.
Note: ZONE_DEVICE can only be enabled on aarch64 since kernel >= 5.7.
ARCH_ENABLE_MEMORY_HOTREMOVE support is missing for previous kernel [2].
[1] https://virtio-fs.gitlab.io/howto-qemu.html
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=bbd6ec605c0fc286c3f8ce60b4ed44635361d58b
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
>From [1]:
This kernel option allow exporting of the QEMU firmware configuration (fw_cfg)
file entries via sysfs. Entries are found under /sys/firmware/fw_cfg when this
option is enabled and loaded.
Enable the suboption to allow the qemu_fw_cfg device to be initialized via the
kernel command line or using a module parameter.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/drivers/firmware/Kconfig?h=v5.4.42#n187
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This driver is intended to be used by mesa virgl Gallium on the guest.
virtio-gpu is enabled by adding "-device virtio-gpu-pci" on the qemu
command line.
It's detected by lspci and dmesg log:
$ lspci
00:01.0 Display controller: Red Hat, Inc. Virtio GPU (rev 01)
$ dmesg
virtio-pci 0000:00:01.0: enabling device (0000 -> 0002)
[drm] pci: virtio-gpu-pci detected at 0000:00:01.0
[drm] virgl 3d acceleration not supported by host
[drm] EDID support available.
[TTM] Zone kernel: Available graphics memory: 51876 KiB
[TTM] Initializing pool allocator
[TTM] Initializing DMA pool allocator
[drm] number of scanouts: 1
[drm] number of cap sets: 0
[drm] Initialized virtio_gpu 0.1.0 0 for virtio2 on minor 0
The framebuffer interface fb0 is now present in /dev
$ ls /dev/fb*
/dev/fb0
See:
https://www.kraxel.org/blog/2019/09/display-devices-in-qemu/https://at.projects.genivi.org/wiki/display/WIK4/GENIVI+Technical+Summit+Session+Content+2018?preview=%2F28412356%2F28412481%2F2018-10-11_GeniviBangalorTechSummit_Virtio_GPU.pdf
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add the CONFIG_PCI symbol due a change in kernel 5.0 [1].
The option was previously enabled by default (default y).
"PCI: consolidate PCI config entry in drivers/pci
There is no good reason to duplicate the PCI menu in every architecture.
Instead provide a selectable HAVE_PCI symbol that indicates availability
of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the
rest in drivers/pci."
Qemu aarch64 provide a PCIe Host bridge but it require CONFIG_PCI_HOST_GENERIC
enabled in the kernel.
With CONFIG_PCI_HOST_GENERIC enabled PCIe host bridge is detected:
$ dmesg
pci-host-generic 4010000000.pcie: host bridge /pcie@10000000 ranges:
pci-host-generic 4010000000.pcie: IO 0x3eff0000..0x3effffff -> 0x00000000
pci-host-generic 4010000000.pcie: MEM 0x10000000..0x3efeffff -> 0x10000000
pci-host-generic 4010000000.pcie: MEM 0x8000000000..0xffffffffff -> 0x8000000000
pci-host-generic 4010000000.pcie: ECAM at [mem 0x4010000000-0x401fffffff] for [bus 00-ff]
pci-host-generic 4010000000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x10000000-0x3efeffff]
pci_bus 0000:00: root bus resource [mem 0x8000000000-0xffffffffff]
pci 0000:00:00.0: [1b36:0008] type 00 class 0x060000
$ lspci
00:00.0 Host bridge: Red Hat, Inc. QEMU PCIe Host bridge
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=eb01d42a77785ff96b6e66a2a2e7027fc6d78e4a
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Qemu for the aarch64 virt emulate an RTC PL031 device.
Enable the kernel support to allow setting the system time.
"date" now return the current time:
Sun Jul 5 20:38:50 UTC 2020
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
And rebase uboot patch.
Tested-by: Maeva Manuel <maeva.manuel@oss.nxp.com>
[Maeva: Tested on i.MX6Quad SabreAuto CPU1]
Signed-off-by: Julien Olivain <julien.olivain@oss.nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This makes the boot script set appropriate root parameters when it's
loaded from a NAND flash device.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The DCON driver for the platform is a staging driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The XO-1 laptop has a NAND flash and firmware capable of reading JFFS2
from it. Enable JFFS2 kernel support so that we'll be able to create
images capable of booting from the internal flash.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A couple of config symbols were mising that things we enable depend on.
Enable them.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This is the keyboard connected via the SP "security processor" on a
XO-1.75. XO-1 has a regular PC keyboard.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
XO-1 has an internal MTD device.
Also, CONFIG_MTD_SPI_NOR was set twice for XO-1.75. One copy is removed,
one remains.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A few conflicts had to be resolved:
- Version number and hash for mesa3d-headers/mesa3d
- Patches added in qemu, and the qemu version number
- The gnuconfig README.buildroot
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch adds support for the i.MX8M Nano EVK Board [1].
The final boot image is created from uboot and firmware binaries in post
image script board/freescale/common/imx/imx8-bootloader-prepare.sh
Note that this config is based on 4.19.35_1.1.0 ; hence, the kernel
configuration needs host-openssl to build.
[1] https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/evaluation-kit-for-the-i-mx-8m-nano-applications-processor:8MNANOD4-EVK
Signed-off-by: Stephane Viau <stephane.viau@oss.nxp.com>
Reviewed-by: Maeva Manuel <maeva.manuel@oss.nxp.com>
Reviewed-by: Julien Olivain <julien.olivain@oss.nxp.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
For some SoCs (i.e.: i.MX8M Nano for now), the DDR training firmware
in the boot image depends on the type of memory installed on a board
(LPDDR4, DDR4, etc...). The previous patch makes this firmware name
agnostic of the DDR type and uses ddr_fw.bin as a generic name. This
patch makes imx8-bootloader-prepare.sh use this generic name,
independently of the kind board DDR type.
Signed-off-by: Stephane Viau <stephane.viau@oss.nxp.com>
Reviewed-by: Maeva Manuel <maeva.manuel@oss.nxp.com>
Reviewed-by: Julien Olivain <julien.olivain@oss.nxp.com>
Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The default iamge size is 32MiB, which is quite low by today's standards.
Besides, the AArch64 kernels are relatively big, which leaves not much
room, if at all, for users to experiment on the default image.
Increase the vfat size to a more reasonable 64MiB.
Note that users who derive an in-tree defconfig for their own case will
allways hit any arbitarary size we put here, so they will anyway have to
also derive this template for their own use-cases.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Commit b80712a16a ("configs/odroidc2:
remove the defconfig") has removed the odroidc2 defconfig, but left
behind a number of files in board/hardkernel/odroidc2, which are now
unused. Let's remove them.
Signed-off-by: Dagg Stompler <daggs@gmx.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This reverts commit f7a887c368 and
23aee3eac4 since the kernel patch
is not needed as soon as qemu >= 3.1.0 is used with a kernel >=
4.11-rc1.
The qemu emulation of sh-sci driver was fixed by adding basic
timeout handling for 9600 bps [1].
[1] https://git.qemu.org/?p=qemu.git;a=commit;h=71bb4ce1b5592cdc03abc48cdf4ecb15b2db81a0
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The Qemu version present in readme.txt files was needed when
the Buildroot's Qemu defconfig was tested manually using the
qemu-system-<arch> binary already present on the host.
This information is now incorrect since we are using host-qemu
package, currently at 4.2.0 version, to do a runtime test since
0c79350638.
For m68k-q800, we can use the upstream qemu since 4.2.0 release
[1].
So, remove this line from the readme.txt.
[1] https://www.qemu.org/2019/12/13/qemu-4-2-0/
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Linux version are changed to the new LTS kernel 5.4.35 for all qemu
defconfigs, except for riscv and csky. Thoses defconfigs are left
unchanged because they require either a custom Linux repository
or a specific kernel header version causing some difficulties when
upgrading to 5.4.35.
Update the nios2-10m50 linux.fragment to update the .dtb build directory
due to a change in kernel 4.20 [1]:
nios2: build .dtb files in dts directory
Align nios2 with other architectures which build the dtb files in the
same directory as the dts files. This is also in line with most other
build targets which are located in the same directory as the source.
This move will help enable the 'dtbs' target which builds all the dtbs
regardless of kernel config.
This transition could break some scripts if they expect dtb files in
the old location.
For x86 and x86_64 kernel, add the CONFIG_PCI symbol due a change in kernel
5.0 [2]. The option was previously enabled by default (default y).
PCI: consolidate PCI config entry in drivers/pci
There is no good reason to duplicate the PCI menu in every architecture.
Instead provide a selectable HAVE_PCI symbol that indicates availability
of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the
rest in drivers/pci.
Update the kernel of ppc-mac99 defconfig added in Buildroot 2019.08.
This version bump was tested on gitlab [4] using the newly introduced
boot-qemu-image.py script [5].
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=118864869805123bf82d666062542440a0fda5dd
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=eb01d42a77785ff96b6e66a2a2e7027fc6d78e4a
[3] a8fac3fcfc
[4] https://gitlab.com/kubu93/buildroot/pipelines/139819874
[5] 0c79350638
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Convert the patch for microblaze kernel added for kernel 3.14 by
Waldemar to git format.
Note: the Waldemar Sob line is missing in the original patch:
fa27985483
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch add support for the low cost QMTECH XC7Z010 starter kit
board [1].
[1] http://www.chinaqmtech.com/xilinx_zynq_soc
Signed-off-by: Martin Chabot <martin.chabot@gmail.com>
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This adds some instructions on how to build and run images for the OLPC
XO laptops.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A defconfig for the nanopi_neo4 was added in
d1cd9cdf26, but then removed in
8af7b11bd8 because an ARM32 compiler was
needed to build ATF, and this was not supported back then.
Thanks to the addition of package/arm-gnu-a-toolchain/, we can now
re-introduce this defconfig.
Compared to the previous defconfig, the following changes were done:
- enable BR2_TARGET_ARM_TRUSTED_FIRMWARE_NEEDS_ARM32_TOOLCHAIN
- bump kernel to 5.4
- increase default rootfs size to 70M
- use mainline u-boot
- switch to Marek Belisko as maintainer
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
NXP i.MX8MNano based SBC with 1GB of LPDDR4 and 16GB eMMC.
More details on the platform here:
https://boundarydevices.com/product/nitrogen8m-nano/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently the volume-label for the vfat partition is a string with
the following pattern: 5934-861D.
Specify the volume-label as "boot" to make it easier to identify it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This defconfig supports the OLPC XO-1 platform.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
There are muliple generations of OLPC laptops, x86 ones based on
Geode, VIA and ARM based with Marvell Armada. All of boot with
OpenFirmware and share some peripherals.
This patch adds the common files.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The support for MacchiatoBin board in U-Boot and Linux has been
significantly improved in the past years. So it no longer makes much
sense to have a separate build configuration based on older vendor
Linux kernel and U-Boot. This commit drops the configuration based on
vendor kernel and U-Boot and renames the mainline-based defconfig.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently the volume-label for the vfat partition is a string with
the following pattern: 5934-861D.
Specify the volume-label as "boot" to make it easier to identify it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Nanopi R1 board with below features:
- U-Boot 2019.01
- Linux 5.0
- Default packages from buildroot
Configuration files taken from Armbian:
https://github.com/armbian/build/blob/master/patch
Signed-off-by: Davide Viti <zinosat@gmail.com>
[Thomas: move U-Boot config and DT to board/friendlyarm/nanopi-r1/uboot/]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit add a post-image script to be used by each qemu board
defconfig in order to generate start-qemu.sh in BINARIES_DIR. The
start-qemu.sh script can be used by Buildroot user to start Qemu
or by a gitlab CI.
To find the correct qemu command line, we use the second post script
argument which must contain "$(BR2_DEFCONFIG)"
BR2_ROOTFS_POST_SCRIPT_ARGS="$(BR2_DEFCONFIG)"
The post-image script expect something like
"/path/to/qemu_aarch64_virt_defconfig" in BR2_DEFCONFIG.
Doing a basename allow to retrieve the name of the defconfig file that
should match on on the "tag" previously introduced in readme.txt files.
For running in the CI, as well as running from a remote machine (e.g. on
a remote build machine), it is better not to start in graphical mode,
but only with the serial line attached to the terminal. The post-build
script prepares two sets of arguments for each case, graphical or
serial, and stores them in the start-qemu.sh script, which then decodes
which to use, based on an argument on the command line (default is still
graphical)
sh4/sh4eb needs a special handling by adding "-serial stdio -display
none"; others only require "-nographics". Some qemu command lines
already contain "-serial stdio", but that does not play nicely with
"-nographics", we remove that when going serial-only (although this
might seem counter-intuitive).
Finally, we ensure the script uses our qemu-system (if it was built).
Signed-off-by: Romain Naour <romain.naour@smile.fr>
[yann.morin.1998@free.fr:
- drop the knowledge about gitlab-ci, replace with an argument to
pass to start-qemu.sh
- adapt the commit log accordingly
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This commit add the name of the Qemu defconfig file after each
qemu command line in order to retrieve it easily.
Since a readme.txt can be shared between several Qemu defconfig, we
need at least one qemu command line in readme.txt for each defconfig.
For now, ignore the qemu_arm_vexpress_tz_defconfig since it fail to build
due to python script issue [1]. Anyway the arm vexpress boot is tested
with qemu_arm_vexpress_defconfig.
[1] http://lists.busybox.net/pipermail/buildroot/2020-February/273738.html
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
There is no reason to create boot.scr in board/udoo/neo and later
install it in TARGET_DIR/boot, leaving a stale file behind.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
There is no reason to create boot.scr in board/solidrun/mx6cubox and
later install it in TARGET_DIR/boot, leaving a stale file behind.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
There is no reason to create boot.scr at board/wandboard and later
install it at TARGET_DIR/boot, leaving a stale file behind.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The U-boot patch has been upstreamed.
Bump U-boot version and drop the patch.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The WDT workaround patch has been upstreamed.
Bump to the new ATF version and drop the patch.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
NXP i.MX8MMini based SBC with 2GB of LPDDR4 and 8GB eMMC.
More details on the platform here:
https://boundarydevices.com/product/nitrogen8m-mini
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- update outdated website URL
- add missing Nitrogen8M configuration
- reword procedure to make it clear it works for all storages
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- To avoid code duplication and to benefit from support script
improvements like empty target dir.
- Note that currently genimage.sh can't be set in defconfig directly for
i.MX8 targets as the POST_SCRIPT_ARGS is used by
imx8-bootloader-prepare.sh
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux 5.4
U-Boot 2020.01
Arm Trusted Firmware v2.2
Buildroot default packages.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Add support for 8MMini and 8MNano
- Upgrade script now resets by default
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Let's clean up "boards/stmicroelectronics" directory a bit
to have everything in particular directories.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The board support package includes the following components:
- U-Boot 2020.01
- Linux 5.4.26
- Buildroot default packages
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
It will be useful for the upcoming introducing stm32mp157a dk2 board.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Let genimage to match the size of the rootfs image instead.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Instead use generic genimage.sh script.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Commit 3f8ace0028
("board/freescale/common/imx: add support for i.MX8") had its
conflicts incorrectly tweaked when applied to Buildroot. The
ahab-container.img is installed with this name (ahab-container.img) by
the imx-firmware package, and not mx8qm-ahab-container.img or
mx8qx-ahab-container.img.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Julien Olivain <juju@cotds.org>
Tested-by: Julien Olivain <juju@cotds.org>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The current Buildroot defconfigs for qemu_x86 and qemu_x86_64
instantiate a console on tty1, which appears on QEMU's
graphical window. Add a console on the serial port (ttyS0) to
be used later for gitlab testing.
This change is need since the script used for gitlab testing
needs to use a serial output with pexpect.
This change is similar to the one made for raspberrypi [1] to
handle HDMI and serial console:
This requires three changes:
1. have two 'console=' entries in the kernel command line: tty1,
then ttyS0;
2. change BR2_TARGET_GENERIC_GETTY_PORT to "console", so it starts
a getty on the last console= passed to the kernel, ttyS0;
3. add a new getty on tty1 to the generated inittab.
Step 2 is actually obtained by removing BR2_TARGET_GENERIC_GETTY_PORT
entirely from the defconfigs, since "console" is the default value.
Step 3 requires a post-build script since the Buildroot makefiles can
configure only one console.
Note: instead of simply adding a new getty on ttyS0 (which would
work) this patch actually changes BR2_TARGET_GENERIC_GETTY_PORT to
instantiate a console on UART, then adds back tty1 via
post-build.sh. This is done only to avoid the "GENERIC_SERIAL" comment
where we instantiate a console on QEMU graphical window, then
instantiate a really-serial console on another line.
The result is these two inittab lines:
console::respawn:/sbin/getty -L console 0 vt100 # GENERIC_SERIAL
tty1::respawn:/sbin/getty -L tty1 0 vt100 # QEMU graphical window
[1] 20878a1017
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As recently reported to the list:
http://lists.busybox.net/pipermail/buildroot/2020-January/271937.html
The hardcoded rootfs partition size can lead to hard to understand build
failures if more packages are added.
So drop the hardcoded partition size. Genimage will then size the partition
to match the size of the rootfs image (which by default is also 60MB for ext4).
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Now that the metadata_csum ext4 option is disabled, we no longer need
the U-Boot workaround.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Use a post-build script to copy uEnv.txt to BINARIES_DIR, as made for
beaglebone.
Drop the post-image script.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Use the same kernel repository and version as configs/beaglebone
- Rename kernel fragment file
- Update U-Boot to 2019.07
- Select weston and qt5wayland
- Select host-uboot-tools with FIT support, required to create the
images.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The correct syntax that Qt5 understands for display names is
"LVDS1", so fix it accordingly.
Reported-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
In board/freescale/common/imx/imx8-bootloader-prepare.sh, when
invoking mkimage_fit_atf.sh, the U-Boot DTB is passed as parameter, to
be included in the FIT image. This parameter usually comes from
BR2_ROOTFS_POST_SCRIPT_ARGS config option. The variable
BL33=u-boot.bin set in the invocation uses the u-boot image which is
including its embedded DTB. This means the U-Boot DTB is included
twice.
The upstream script mkimage_fit_atf.sh plus its Buildroot patch are
meant to use by default the nodtb variant and use the DTB in a
separate image. See [1] and [2].
The U-Boot default DTB which will be included in u-boot.bin image is
selected with U-Boot CONFIG_DEFAULT_DEVICE_TREE, or DEVICE_TREE
variable when invoking "make". If one of those option is not aligned
to the BR2_ROOTFS_POST_SCRIPT_ARGS config option, it's possible the
two included U-Boot DTBs are different. If such case happens, the
built-in DTB is always used, regardless of the other one, selected
with BR2_ROOTFS_POST_SCRIPT_ARGS.
For example, this case happens for TechNexion Pico Pi i.MX8M and
i.MX8MMini. Since the U-Boot defconfig assumes the nodtb version will
be used, it does not set the default DTB. The u-boot.bin will include
the fsl-imx8mm-evk instead. Including the wrong board DTB breaks the
USB and UMS commands (and possibly others). Since those boards does
not have SD card slots, a recovery serial download is needed at every
update.
This patch make sure that only the separate U-Boot DTB will be
included in the FIT image by using the nodtb variant.
[1] https://source.codeaurora.org/external/imx/imx-mkimage/tree/iMX8M/mkimage_fit_atf.sh?h=rel_imx_4.14.98_2.0.0_ga#n35
[2] https://git.busybox.net/buildroot/tree/package/imx-mkimage/0001-add-support-for-overriding-bl32-and-bl33-not-only-bl.patch?h=2019.11#n42
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since kernel commit a5a56f07c272 ("ARM: imx_v6_v7_defconfig: Select the
coda driver as module") the VPU coda driver is selected as module, so it can
be safely removed from linux_qt5.fragment.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The correct syntax that Qt5 understands for display names is
"HDMI1" and "LVDS1", so fix it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 3468ef16fa
("configs/pc_x86_64_efi: use genimage GPT partition table support")
had a small typo on the path to grub boot.img file: i387-pc instead of
i386-pc, which causes a build failure.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/378314412
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Alexandre PAYEN <alexandre.payen@smile.fr>
Cc: Carlos Santos <casantos@datacom.com.br>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This remove the file boot.cmd to use an extlinux.conf instead.
Signed-off-by: Louis Aussedat <aussedat.louis@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This configuration builds a 64bit image for RaspberryPi 4.
Signed-off-by: Arthur Courtel <arthur.courtel@smile.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The pi3-minuart-bt Device Tree overlay has been renamed to
miniuart-bt, as it is useful/usable for other platforms than the
RPi3. So we use this DT overlay and rename the
--add-pi3-miniuart-bt-overlay option to --add-miniuart-bt-overlay
accordingly.
Signed-off-by: Arthur Courtel <arthur.courtel@smile.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Instead use the generic infrastructure for u-boot scripts and genimage.
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As already done in post-build.sh, to prevent hiding errors.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Let genimage determine rootfs partition size based on the filesystem
image size.
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 68b5b79b2f has set the getty port to the default console but left
"ttyO0" in bootargs, in the U-Boot environment. Use "ttyS0", instead.
Also set loadaddr to 0x82000000 and fdtaddr to 0x88000000, replacing the
values that were valid for the ancient U-Boot and Linux pre-installed on
old boards but cause boot hangs with the current versions.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Thanks to the introduction of GPT partition table support in genimage,
this commit improves the pc_x86_64_efi_defconfig to remove the use of
the custom script creating the image.
Tested in QEMU, not on a physical device.
So:
- revert commit fee29b05bb7db25e37c8a5175ce00dc712554edf[1]
- add GPT support
- tweak shell script to add the correct UUID in genimage config.
[1]: https://git.buildroot.net/buildroot/commit/?id=fee29b05bb7db25e37c8a5175ce00dc712554edf
[2]: https://git.buildroot.net/buildroot/commit/?id=79b8540d624ac4846ba341b1b9691eccacf0bc05
Signed-off-by: Alexandre PAYEN <alexandre.payen@smile.fr>
Cc: Carlos Santos <casantos@datacom.com.br>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[Thomas:
- drop commented code in post-build.sh
- take into account comments made by Carlos Santos in
http://patchwork.ozlabs.org/patch/1143502/]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use the pi3-miniuart-bt device tree overlay (as the 32bit raspberrypi3
defconfig) instead of the enable_uart option.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes reference path "../build/optee_os-" to "./output/build/optee-os-"
as package is optee-os and symbol file here is reached from BR top
dir and assuming output in output/.
Updates GDB tool name to arm-linux-gdb.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This change introduces a Qemu board for an Armv7-A target executing
with OP-TEE secure world services. The target Linux based normal world
embeds the standard minimal filesystem with OP-TEE non-secure components
embedded files from OP-TEE test, examples and benchmark packages.
qemu_arm_vexpress_tz_defconfig differs from qemu_arm_vexpress_defconfig.
Supporting both secure and non-secure worlds on the Arm target mandates
a secure world, here OP-TEE OS, and a bootloader to boot both worlds,
here TF-A (boot/arm-trusted-firmware). Here non-secure Linux kernel is
booted through U-boot
TF-A bootloader (BL1/BL2) => OP-TEE (BL32) => U-boot (BL33).
| Executes as secure | Secure | Execs as Non-secure
| Loads BL32/BL33 in RAM | Jumps to BL33 | Always booted after
| Jumps to BL32 once done | as Non-secure | secure world inits
Vexpress and vexpress-tz defconfigs also differs in that Qemu emulates
a Cortex-A9 in the former and a Cortex-A15 in the later. Cortex-A15
is the Armv7-A CPU used in upstream TF-A and OP-TEE OS packages hence
selected here.
Defconfig adds a fragment to the Linux kernel native configuration to
enable OP-TEE driver support.
Defconfig adds a fragment to the U-Boot native configuration set boot
command, enable semihosting and remove U-Boot persistent environment
storage support.
The defconfig also enables build of the Qemu emulator in case the
system installed Qemu does not yet support CPU TrustZone secure state.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
[Arnout, with the help of Peter: correct spelling mistakes in readme,
fix U-Boot version to 2019.01, download tarball of TF-A instead of git]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
That is useful and needed for upcoming introducing stm32mp157a-dk1 board.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
genimage makes a full copy of the given rootpath to ${GENIMAGE_TMP}/root
so passing TARGET_DIR would be a waste of time and disk space. We don't
rely on genimage to build the rootfs image, just to insert a pre-built
one in the disk image.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Use a post-build script to copy uEnv.txt to BINARIES_DIR, as made for
beagleboneai.
Keep the post-image script because it is still used by beaglebone_qt5.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Change partition name according to the U-Boot requirements.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
QT_QPA_EGLFS_ALWAYS_SET_MODE=1 needs to be exported, otherwise the Qt5
Cinematic demo throws a storm of the following messages:
Could not queue DRM page flip on screen LVDS1 (Invalid argument)
Improve the instructions by mentioning such requirement.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 5facee5cc3 ("configs/solidrun_clearfog_gt_8k: bump versions of
BSP components") broke automatic load of the mv88e6xxx dsa driver. The
kernel configuration makes the driver a module, which is not loaded
automatically at boot. Mark mv88e6xxx dependencies built-it to fix that.
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add basic support for the Libre Computer "La Frite" SBC.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since the bump to the 20190819 snapshot there is now a dedicated dts file
for the rpi0, so use that rather than the rpi-b-plus one:
bd1336d8b6
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes#12816
Commit 42d22f3bdb ({configs/raspberrypi,package/rpi-firmware}: bump
kernel/firmware to 20190819 version) updated the kernel version but failed
to take into consideration that the rpi0w dts file has been renamed:
6f91b5dbfd
Fix it by renaming the dts/dtb file referenced from the kernel build and
genimage.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489410
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489367
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489328
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489329
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489325
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig has been failing to build since we switched the default
gcc version to gcc 8.x, as the Linux kernel version is too old and
doesn't contain the necessary fixes to build with gcc >= 8.x.
Despite several pings to the original submitter of the defconfig
(which is not listed in MAINTAINERS), no fix has been sent, so it is
time to drop this defconfig before the 2019.08 release.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489442
Cc: Patrick Keroulas <patrick.keroulas@savoirfairelinux.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The TS-7680 defconfig does not build with gcc 8.x and 9.x because it
uses an old 3.14 kernel. Technologic Systems, the board manufacturer
recently released an updated 4.9 based kernel on a separate repository
on github.
Bump the kernel release from 3.14.28 to 4.19.186 and update the linux
defconfig name as requested in the TS-7680 documentation [1].
[1] https://wiki.embeddedarm.com/wiki/TS-7680#Linux_4.9.y
Signed-off-by: Julien Grossholtz <julien.grossholtz@openest.io>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit adds a minimal defconfig to build a Buildroot system for
the STM32MP157 Discovery Kit, which is the low-cost evaluation
platform for the new STM32MP157 system-on-chip from ST. This
system-on-chip features a single or dual Cortex-A7, a single
Cortex-M4, and a wide variety of peripherals.
This commit includes a custom linux configuration file, because there
is no specific defconfig for this platform in the kernel, only
multi_v7_defconfig supports it, which is really a massive
defconfig. That's why a custom linux configuration file is added.
A small U-Boot config fragment allows to disable the watchdog, so that
userspace by default doesn't need to have a watchdog daemon running.
The vendor U-Boot and Linux trees are used for the moment, but the
platform support is being upstreamed, so switching to upstream
versions will be possible in the relatively near future.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This is based on the pi3 defconfig. There is currently no 64-bit support
since the upstream kernel does not build in this configuration.
Signed-off-by: Michael Cullen <michael@michaelcullen.name>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch adds support for the HiFive Unleashed board. This includes
building the firmware, kernel and rootFS for the HiFive Unleashed.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
[Thomas:
- fix the directory name hifive_unleased -> hifive-unleashed
- drop from readme.txt the instructions about manually flashing each
partition, since we have a full SD card image
- drop the custom post-image.sh script]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Custom u-boot
Linux v5.1
ATF v2.0
Buildroot default packages
Tested-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1
- Use final 5.1 kernel
- Use default ext2 filesystem]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
u-boot v2019.04
Linux v5.0
Buildroot default packages
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas: use BR2_TARGET_UBOOT_BOOT_SCRIPT to generate the U-Boot
script, instead of doing it in the post-build]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux 5.1
Custom U-Boot
Arm Trusted Firmware v2.0
Buildroot default packages
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use the headers from the kernel, by using
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1=y
- Use the default ext2 rootfs size]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux 5.1
Custom U-Boot
Arm Trusted Firmware v2.0
Buildroot default packages
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use the headers from the kernel, by using
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1=y
- Use the default ext2 rootfs size]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux 5.1
Custom U-Boot
Arm Trusted Firmware v2.0
Buildroot default packages
Tested-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use the headers from the kernel, by using
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1=y
- Use the default ext2 rootfs size]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux v5.2
Custom U-Boot
Arm Trusted Firmware v2.0
Buildroot default packages
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
[Thomas:
- Use the kernel headers from the kernel, by using
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_2=y
- Use the final 5.2 kernel instead of rc1.
- Use the default ext2 rootfs size]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The most important change is to use the toolchain compiled by
buildroot itself. We also bump kernel to 5.0 with kernel.org.
Gx6605s' PHYS_OFFSET if 0x10000000 and we make qemu and gx6605s the
same to ease maintaince. This PHYS_OFFSET is also OK for 610 qemu.
In this patch we add gx6605s.dts in board/csky, because linux-5.0
doesn't contain gx6605s.dts in its tree.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Display variant dtbs are no longer part of the linux-at91 tree.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
PowerPC kernel developers were after a userspace for testing 32-bit
powerpc kernels. This machine both suits that requirement and has
support in qemu. It's also a fairly common piece of 32-bit ppc hardware.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Daniel Axtens <dja@axtens.net>
[Peter: lock kernel/headers to 5.2.4]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to 2019.07 and kernel to version 5.1.16.
Also
- adjust the U-Boot binary name after DM conversion.
- add missing notes about DFU
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Also
- adjust the U-Boot binary name after DM conversion.
- add missing notes about flashing U-Boot and SPL
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
For boards like imx7d-pico, u-boot.img changes to u-boot-dtb.img in
U-Boot v2019.07. Therefore, we need to pick u-boot.img or u-boot-dtb.img
depending on the board configuration.
Just like was done in commit 52344e556f for the generic genimage
template, replace the U-Boot file name with UBOOTBIN, which is set
according to the BR2_TARGET_UBOOT_FORMAT_* option. We also need to set
the correct value for this variable for the u-boot.img and
u-boot-dtb.img cases.
While we're at it, rename the partition from 'u-boot-img' to 'u-boot',
to stay consistent with the generic genimage template.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
[Arnout: correct u-boot.img condition, rework commit log]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
On my machine, it happens once in a while that the virtualised machine
boots too fast for the rootfs to be available at the time the kernel
tries to mount it.
For example, board/qemu/arm-vexpress/readme.txt suggested changing
"-smp 1" up to "-smp 4". But doing so here causes a kernel panic:
VFS: Cannot open root device "mmcblk0" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
1f00 131072 mtdblock0
(driver?)
1f01 32768 mtdblock1
(driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(0,0)
So, add the oh-so-useful 'rootwait' option to all kernel command lines
for qemu defconfigs.
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Mark Corbin <mark.corbin@embecosm.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump Linux and U-Boot versions.
The Linux configuration file and patches are no longer needed.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
[Thomas: also use a tarball for U-Boot.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the 32-bit defconfig to use the latest kernel. This requires a
patch to revert a ABI to ensure that the glibc port continues to work.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for the SolidRun Armada 8040 based Clearfog GT-8K. This
board has the same processor as the Macchiatobin, so we can reuse the
Macchiatobin U-Boot and image definitions.
The kernel fragment enables drivers that are necessary to make
networking ports work (SFP, Ethernet port, and Ethernet switch).
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump Linux to 5.1 and U-Boot to version 2019.01.
U-Boot patch is no longer needed, applied upstream.
U-Boot defconfig name for this board has changed to pico-pi-imx7d.
U-Boot now supports distrobootcmd for this board, so add the appropriate
extlinux.conf and use SPL+u-boot.img instead of u-boot.imx. Note that
the common freescale post-image script handles things appropriately
based on the selected options in .config.
dosfstools and mtools are no longer needed to build the image.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
[Arnout: remove BR2_PACKAGE_HOST_DOSFSTOOLS and BR2_PACKAGE_HOST_MTOOLS]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Modern U-Boot assumes a layout where the first partition is an ext2 and
the kernel and dtb can be found in /boot. In other words, a layout
without boot partition.
Add a genimage.cfg template for the freescale defconfigs with such a
layout.
For now, only the layout with SPL+u-boot.img is added. It's unlikely that
the u-boot.imx approach will be used.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
For the boot image creation for the i.MX8MM, the main differences with
i.MX8M are that there is no HDMI firmware image passed, and the ATF
load address is different.
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Following commit fee29b05bb
("configs/pc_x86_64_efi: use a GPT partition table"),
board/pc/grub-efi.cfg is no longer used anywhere: the
post-image-efi-gpt.sh script generates the grub configuration.
Also, since post-image-efi-gpt.sh generates a grub configuration file
that uses the root filesystem partition UUID as the root= kernel
argument, the instructions in the readme.txt file to tweak root= from
/dev/sda2 to /dev/vda2 is no longer relevant. This was noted in the
commit log of fee29b05bb:
The root filesystem location is passed to the kernel by a partition
UUID, so it is possible to boot on QEMU, directly from the disk image,
or dump the image to a physical device.
Fixes: #11841
Cc: Pete Morici <pmorici@dev295.com>
Cc: Carlos A. M. dos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Very similar to orangepi-zero, except that the board has a 16MB SPI flash, a
2nd ethernet port is provided through a Realtek RTL8152 and wifi is provided
through a Realtek RTL8189FTV (no mainline driver, not supported).
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Default value of CONFIG_SYS_BOOTM_LEN in u-boot causes board reset for
large uImage files, so add u-boot patch to increase the maximum kernel
image size.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The readme.txt would contain similar content for either processor
family, so this patch consolidates the usage and adds the new
T2080 notes.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add Andes 32-bit defconfig for AE3XX platform.
Signed-off-by: Che-Wei Chuang <cnoize@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
Signed-off-by: Nylon Chen <nylon7@andestech.com>
[Thomas:
- fix commit title to match the defconfig name
- use the external toolchain package]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Default value of CONFIG_SYS_BOOTM_LEN in u-boot causes board reset for
large uImage files, so add u-boot patch to increase the maximum kernel
image size.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch enables the inclusion of the Pi's overlays. Previously
the overlays were not included in the genimage configuration.
This patch ensures overlays are included in the sdcard (when
enabled) by defaulting to the inclusion of an empty
output/images/rpi-firmware/overlays directory in genimage cfg.
The Pi's overlays are built with the following config
variables:
BR2_PACKAGE_RPI_FIRMWARE=y
BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTBS=y
BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS=y
BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
BR2_LINUX_KERNEL_IMAGE_NAME="Image"
BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="Image modules dtbs"
After building, the dtbo files are present in the
output/images/rpi-firmware/overlays directory but not added
to the sdcard because they are missing from the genimage cfg
file.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
[Arnout: fix indentation, and add comment explaining why an empty
directory is created.]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This bumps to linux/linux-headers 5.0 and u-boot version 2019.01. The
kernel patch is no longer needed, as the Device Tree for the platform
is now upstream.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use OpenSBI by default instead of riscv-pk (BBL).
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reduce the config fragment to the bare minimum to enable 32-bit
support. This means we are as close as possible to the arch
defconfig.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Convert the config to the arch defconfig plus a fragment. When this
fragment is applied we will generate the same config as we previously
did.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The old 3.4 Linux kernel used by this defconfig doesn't build with gcc
7.x.
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The update of imx-mkimage in commit
c14d92d439
broke the imx8-bootloader-prepare.sh script for i.MX8M, used in
freescale_imx8mqevk_defconfig
The updated mkimage_fit_atf.sh script in imx-mkimage now needs
a ATF_LOAD_ADDR variable, which was set to 0x00910000 for i.MX8M.
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This defconfig was added in October 2016 and was never updated since
then. It currently fails to build because U-Boot is too old and
doesn't build with host-openssl in version 1.1.x.
On February 13, 2019, the original submitter was notified, but didn't
reply, so let's remove the defconfig for this platform.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/165766194
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Linux version are changed to 4.19.16 (LTS) for all qemu defconfigs,
except for riscv. riscv defconfigs are left unchanged because they have
a custom Linux repository causing more difficulties when upgrading to
4.19 for riscv32. And for the riscv64, it has been updated recently to
Linux 4.20 by another contributor.
Patch for arm-versatile-nommu is changed into a git format
Add cache attributes for xtensa-lx60-nommu config because the commit
7bb516ca54
added a new config variable for memory cache attribute:
CONFIG_MEMMAP_CACHEATTR
All these updated configs have been built successfully.
Signed-off-by: Gerome Burlats <gerome.burlats@smile.fr>
Cc: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Configuration contains:
- building tpl, spl and u-boot (forked u-boot repository)
- booting from SD card and network via PXE
- working ethernet, usb and uart
- minimal rootfs with busybox
- ready to flash SD card image
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since all EFI-based systems support GPT, this commit changes
pc_x86_64_efi to use a GPT partition table. It shows an example of how
to craft a disk image with GPT partitioning instead of MBR. This is
achieved by means of a post-image script which uses
mkdosfs+mcopy+sfdisk, since genimage is unable to deal with GPT. Long
term, it would be ideal if genimage had GPT support, but until then,
this script shows how to achieve creating a GPT-based disk image.
The script was kept as simple as possible to make it easy to understand
and adapt for other purposes.
The root filesystem location is passed to the kernel by a partition
UUID, so it is possible to boot on QEMU, directly from the disk image,
or dump the image to a physical device.
Signed-off-by: Carlos Santos <casantos@datacom.com.br>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
qemu_aarch64_virt_defconfig (implicitly) specifies cortex-a53, so adjust the
QEMU command line to also emulate a a53 instead of a57.
Also adjust the defconfig to explicitly specify a53 for consistency/clarity.
Signed-off-by: Gerome Burlats <gerome.burlats@smile.fr>
Cc: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Since riscv64 works with linux default defconfig, this patch drop custom config.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
Tested-by: Mark Corbin <mark.corbin@embecosm.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot and kernel to their latest releases.
Remove the documented limitations. Recent kernels added support for the
SOM SPI flash, and the carrier SFP port.
Mention the 'dd' command in the warning text. No script is involved.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Before this commit, the grub configuration file was copied to the
TARGET_DIR in a post-image hook, after the filesystem has been
generated. It was kinda working because the board/pc's grub
configuration and the default one are the same and the later was
copied during the build process of the grub2 package.
This commit ensures the custom board/pc grub configuration is copied at
the right time.
Signed-off-by: Grégoire Delattre <gregoire.delattre@gmail.com>
Reviewed-by: Matt Weber <matthew.weber@rockwellcollin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This updates LEGO MINDSTORMS EV3 to Linux kernel 4.19 and U-Boot
2018.11. This kernel brings Bluetooth support, so some Bluez packages
are also added. Also, we now have proper device tree support, so a few
things are rearranged in the flash and SD card images since the DTB is
no longer appended to the kernel image.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The first stage bootloader on LEGO MINDSTORMS EV3 only loads the first
256K of the flash memory (this is hard-coded in an EEPROM). So, the
second stage bootloader (U-Boot) cannot exceed this size.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
NXP U-Boot tree has the following build issue:
MKIMAGE u-boot-dtb.imx
Error: No BOOT_FROM tag in board/freescale/mx7dsabresd/imximage.cfg.cfgtmp
arch/arm/imx-common/Makefile:91: recipe for target 'u-boot-dtb.imx' failed
make[2]: *** [u-boot-dtb.imx] Error 1
Makefile:877: recipe for target 'u-boot-dtb.imx' failed
This issue has been fixed by commit f916757300c1 ("imx: Create
distinct pre-processed mkimage config files"), so backport this
commit to the NXP U-Boot tree in order to fix the build error.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/136980027
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch updates the csky custom external toolchain to fix a broken
host dependency of gdb on libexpat.so.0 (most hosts now ship
libexpat.so.1). gdb is required to copy and and boot the kernel (see
board/csky/readme.txt). The updated gdb no longer has this host
dependency, which solves the issue.
Since this external toolchain was built and tested with csky kernel
4.9.56, this patch also updates to that kernel version.
Finally, this 4.9.56 csky kernel changed its default bootargs. So we
add a patch to preserve the same behavior as the previous version.
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Orangepi lite2 board has AP6356S WiFi/BT combo, but does
not have ethernet port. So it makes sense to enable wireless
networking by default:
- add broadcom wireless firmware package to image
- add basic wireless tools to image
- add rootfs overlay with proper NVRAM file for on-board AP6356S chip
- add mdev to image to enable module autoloading
- update readme.txt to test wifi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Orangepi Lite2 board with below features:
- U-Boot 2018.09
- Linux 4.19.0-rc8
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Orangepi One Plus board with below features:
- U-Boot 2018.09
- Linux 4.19.0-rc8
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently, U-Boot is failing to build, due to some issues
with the toolchain and the U-Boot port.
Fix it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
New generic defconfig for aarch64, to run on aarch64 servers compliant
with EFI firmware and ACPI.
This can also be tested with qemu, and is useful so that we have an
arm defconfig with grub enabled. Tested with qemu 2.11.2 and AAVMF,
the aarch64 virtual machine UEFI firmware.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
[Thomas: extend readme.txt with more details]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
4.18 brought cpufreq support for H3, but sunxi_defconfig does not enable the
ondemand cpufreq govenor so the frequency is dynamically adjusted - So
enable it in linux-extra.config.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
4.18 brought cpufreq support for H3, but sunxi_defconfig does not enable the
driver for the sy8106a regulator used on the board or enable the ondemand
cpufreq govenor so the frequency is dynamically adjusted - So enable these in
linux.fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The default ORC unwinder requires libelf to be built. While we could
build libelf using BR2_LINUX_KERNEL_NEEDS_HOST_LIBELF, we probably
don't really need the ORC unwinder in the PC defconfigs, so let's use
the frame pointer unwinder instead.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/123771107
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the kernel and U-Boot versions to the actual versions in use.
Update the description of supported hardware features.
Add a note that the stale SPI flash environment issue only affects the
vendor BSP.
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to version 2018.11. This version supports autodetection of
SD/eMMC boot source, so we can now enable environment load from SD card.
Add a U-Boot kconfig fragment that sets SD/eMMC as environment load/save
device. This avoids stale environment values from the SPI flash. That in
turn, allows to use the more convenient distro boot which is enabled in
the default environment.
Bump kernel to version 4.19.2. This version enables
CONFIG_PHY_MVEBU_CP110_COMPHY in the arm64 defconfig, so remove it from
the kernel kconfig fragment. Enable support for SFP modules detection
and configuration. Leave the PHY drivers for now to keep them built into
the kernel. The kernel defconfig builds these drivers as modules. But
that does not work as expected in the default configuration.
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Amarula A64-Relic board has AP6330 WiFi/BT combo, but does
not have ethernet port. So it makes sense to enable wireless
networking by default:
- add broadcom wireless firmware package to image
- add basic wireless tools to image
- add rootfs overlay with proper NVRAM file for on-board AP6330 chip
- add mdev to image to enable module autoloading
- update readme.txt to test wifi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Amarula A64-Relic board
with below features:
- U-Boot 2018.07
- Linux 4.17.0-rc6
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas: add missing BR2_TARGET_UBOOT_NEEDS_PYLIBFDT=y and
BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y options.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Some ZynqMP device trees in the kernel have a dot in their name,
for example "zynqmp-zcu102-rev1.0". The post image script
left out the part after the dot and created an invalid symlink.
Signed-off-by: Francois Beerten <fbeerten.git@colabti.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch provides support for the board Odroid XU4. It uses a recent
4.14 kernel released by Hardkernel, and the current u-boot 2017.05
also from Hardkernel.
Signed-off-by: Pierre CROKAERT <pct@crookies.net>
[Thomas:
- Update DEVELOPERS file
- Update .gitlab-ci.yml file
- Simplify the boot.ini script
- Add missing BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_14 option
- Add BR2_PACKAGE_HOST_DOSFSTOOLS and BR2_PACKAGE_HOST_MTOOLS since a
VFAT filesystem is generated
- Keep the default root filesystem size, since it is sufficient.
- Reduce the size of the VFAT filesystem]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add intial support for Bananapi M2 Ultra board based on the Allwinner
R40 SoC.
- U-Boot 2018.07
- Linux 4.18.12
Board specifications: http://www.banana-pi.org/m2u.html
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add RISC-V 64-bit defconfig for QEMU virt machine.
Tested with QEMU 2.12.1
Signed-off-by: Mark Corbin <mark.corbin@embecosm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit renames olimex_a20_olinuxino_lime_mali to
olimex_a20_olinuxino_lime_legacy, because the upstream Linux kernel
now also supports using the Mali GPU.
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch removes duplicate messages in Linux log on HSDK board.
For HSDK board we setup bootargs via device tree,
see https://elixir.bootlin.com/linux/latest/source/arch/arc/boot/dts/hsdk.dts#L25
"console=ttyS3" was mistakenly placed in u-boot bootargs which are
appended to Kernel bootargs in case of using buildin .dtb.
Before patch log is like:
------------------------8<-------------------------------------
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz,...
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz,...
mmc0: new SDHC card at address 59b4
mmc0: new SDHC card at address 59b4
blk_queue_max_segment_size: set to minimum 8192
blk_queue_max_segment_size: set to minimum 8192
------------------------>8-------------------------------------
After patch log is like:
------------------------8<-------------------------------------
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz,...
mmc0: new SDHC card at address 59b4
blk_queue_max_segment_size: set to minimum 8192
------------------------8<-------------------------------------
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Resurrect support for RIoTboard after 2018.02.x deprecation.
Signed-off-by: Nikolay Dimitrov <nikolay.dimitrov@retrohub.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
At first the support for i.MX8MQ processors was minimal, hence this
section in the readme file.
Since then, GPU support was added [1] in master and VPU in next [2].
So drop this section as it is confusing people and no one maintains it.
[1] https://git.buildroot.net/buildroot/commit/?id=84afda9c
[2] https://git.buildroot.net/buildroot/commit/?id=82732071
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
512B is not a correct size to express "512 bytes", and causes a
genimage failure:
ERROR: Invalid size suffix 'B' in '512B'
To express "512 bytes", using just "512" is sufficient. With this
commit, genimage works fine, and we indeed have a 512 bytes unused
partition:
$ fdisk -l output/images/sdcard.img
Disk output/images/sdcard.img: 60 MiB, 62915584 bytes, 122882 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x00000000
Device Boot Start End Sectors Size Id Type
output/images/sdcard.img1 1 1 1 512B 0 Empty
output/images/sdcard.img2 2 524289 524288 256M 83 Linux
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/88314963
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
As for sh4-r2d (little-endian) restore the old sh-sci driver behaviour
for sh4eb-r2d.
Tested with qemu_sh4eb_r2d_defconfig.
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This reverts commit 18e8cf159177100e69d528293f8cf6875c0b1bca (kernel)
The last Qemu kernel update [1] introduced a regresion in sh4 SCIF
serial device. Some keyboard presses are very slow to be taken into
account, perhaps not even taken into account at all. This would
explain why our test infrastructure doesn’t manage to login as root
[2][3][4].
git bisect reported a kernel patch from 4.11, increasing RX FIFO
trigger defaults value for sh-sci (H)SCIF. The kernel patch itself
looks good but the Qemu emulation is not ready to handle this new
setting.
>From Qemu (2.12.0): target/sh4/README.sh4
"Configuration of the second serial port (SCIF) is supported. FIFO
handling infrastructure has been started but is not completed yet."
We can't use the first serial port (ttySC0) because it's the second
SH UART that's emulated by Qemu.
In order to be able to test sh4 architecture with newer kernel,
revert to the old behaviour.
[1] 03fb00f217
[2] https://gitlab.com/free-electrons/toolchains-builder/-/jobs/72006425
[3] https://gitlab.com/free-electrons/toolchains-builder/-/jobs/72006427
[4] https://gitlab.com/free-electrons/toolchains-builder/-/jobs/72006426
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
U-Boot SPL configures pinmuxes, clocks and other low-level devices. On
the Xilinx ZynqMP SoCs the code to do this resides in a file called
psu_init_gpl.c which is initially generated by the Xilinx development
tools. Add an option to pass these files from the outside (e.g. in the
board files).
For this to work properly, a patch to U-Boot is needed. However this
patch must be applied by each defconfig using
BR2_TARGET_UBOOT_ZYNQMP_PSU_INIT_DIR. If it were in boot/uboot/ to be
applied unconditionally, it would break the build for configs using a
U-Boot version where the patch is already applied.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Reviewed-by: Joel Carlson <JoelsonCarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
[Thomas: add comment about U-Boot version requirements to use this
option.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This adds support the Xilinx ZCU106 development board.
[Tested on the ES2 (Engineering Sample 2) version of the board]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
In order to boot on the Xilinx ZynqMP SoCs, U-Boot SPL requires a
recent PMU firmware loaded. Instruct U-Boot to add pmufw.bin to the
boot.bin file together with U-Boot SPL, and the boot ROM will load
both.
For this to work properly, a patch to U-Boot is needed. However this
patch must be applied by each defconfig that wishes to use
BR2_TARGET_UBOOT_ZYNQMP_PMUFW. If it were in boot/uboot/ to be applied
unconditionally, it would break the build for configs using a U-Boot
version higher than 2018.7-rc1 where the patch is already applied.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Reviewed-by: Joel Carlson <JoelsonCarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
[Thomas:
- indicate that this feature requires U-Boot 2018.07, since commit
c7df098a71e05dc81cee818747759e8060b59626 is needed.
- define UBOOT_ZYNQMP_KCONFIG_PMUFW only once, and instead use a
variable named UBOOT_ZYNQMP_PMUFW_PATH to store the path to the PMU
firmware]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Use proper ARCH for mkimage command
- Use different U-Boot binary name depending on ARCH
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
6x_bootscript/6x_upgrade have been deprecated for more than a year.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The upgrade.cmd script expects the binary to be named
u-boot.<uboot_defconfig>.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Allow user to override the hardcoded dtb name by using
BR2_ROOTFS_POST_SCRIPT_ARGS.
The only user of this script, configs/freescale_imx8mqevk, is updated
accordingly.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for flashing the u-boot-dtb.imx binary in the SD card
when a target selects BR2_TARGET_UBOOT_FORMAT_DTB_IMX.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The 2017 MinnowBoard Turbot skews no longer use the Realtek 8169
Ethernet chip. The Turbot D0 uses The Intel I211, the Turbot Dual
Ethernet has an I210 (quad-core) or I211 (dual-core).
Add CONFIG_IGB to the Linux config but keep the Realtek 8169 support
to avoid breaking older boards
Tested on Turbot D0, lspci -k shows the igb driver is used:
03:00.0 Class 0200: 8086:1539 igb
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add a defconfig for the Olimex A10-OLinuXino-LIME, reusing most
of the A20-OLinuXino-Lime and A13-OLinuXino files (sym links).
The configurations for Olimex A10-OLinuXino-LIME feature:
- U-Boot 2018.03
- Mainline Linux kernel 4.14.26
Signed-off-by: Leon Anavi <leon.anavi@konsulko.com>
[Arnout: remove commented-out BR2_ARM_EABIHF=y (which is default)]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
As per latest Raspberry Pi firmware documentation, the option
'arm_control' has been deprecated in favor of 'arm_64bit'.
Fixes https://bugs.busybox.net/show_bug.cgi?id=11111.
Signed-off-by: Jason Tang <tang@jtang.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the kernel version to 4.17.2.
Update U-Boot version to 2018.05.
Migrate to U-Boot generic distro configuration which is easier than the
hand written boot script.
Improve the 'dd' command example in readme.txt.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
To not maintain custom copy of inittab file lets adopt approach
used in raspberrypi adding post-build script for synopsys/axs10x
boards.
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Apply modifications made in recent commits:
- 456ea9871e busybox: add /dev/std{in, out, err} symlinks to inittab
- 13dbe73782 busybox: reduce number of mkdir calls in inittab
- 8a89d290d4 busybox: add an inittab entry to activate swap
Signed-off-by: Carlos Santos <casantos@datacom.com.br>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
4.17 brings support for HDMI out, but sunxi_defconfig hasn't been updated to
enable the drivers - So add a kernel fragment to enable them.
Likewise, analog audio has been supported since 4.10, but the driver isn't
enabled in sunxi_defconfig, so enable it in the fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump kernel to version 4.17 and U-Boot to 2018.05.
As the dtb file has been renamed in mainline, make the necessary
adjustments in U-Boot environment and also in
BR2_LINUX_KERNEL_INTREE_DTS_NAME.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump kernel to version 4.17 and U-Boot to 2018.05.
As the imx_v6_v7_defconfig in 4.17 already selects the
CONFIG_CFG80211_WEXT option, the linux.fragment can
be simply removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump linux as well headers to v4.16 version, this eventually drop the
wifi patch since it has been merged to Linux v4.16.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
All linux configs are renamed to a version neutral filename
to avoid further renaming on kernel bumps.
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.16.7 2.12.0 YES OK
arm_versatile 4.16.7 2.12.0 YES OK
arm_versatile_nommu 4.16.7 2.12.0 YES OK (3)
arm_vexpress 4.16.7 2.12.0 YES OK
m68k_mcf5208 4.16.7 2.12.0 YES OK
m68k_q800 4.16.7 q800-v2.11.0 NO (2) OK
microblazebe 4.16.7 2.12.0 YES OK
microblazeel 4.16.7 2.12.0 YES OK
mips32r2el_malta 4.16.7 2.12.0 YES OK
mips32r2_malta 4.16.7 2.12.0 YES OK
mips32r6el_malta 4.16.7 2.12.0 YES OK
mips32r6_malta 4.16.7 2.12.0 YES OK
mips64el_malta 4.16.7 2.12.0 YES OK
mips64_malta 4.16.7 2.12.0 YES OK
mips64r6el_malta 4.16.7 2.12.0 YES OK
mips64r6_malta 4.16.7 2.12.0 YES OK
nios2-10m50 4.16.7 2.12.0 NO OK
or1k 4.16.7 2.12.0 NO OK
ppc_g3beige 4.16.7 2.12.0 YES OK
ppc_mpc8544ds 4.16.7 2.12.0 YES OK
ppc_virtex_ml507 4.16.7 2.12.0 NO OK
ppc64_pseries 4.16.7 2.12.0 YES OK
ppc64le_pseries 4.16.7 2.12.0 YES OK
ppc64_e5500 4.16.7 2.12.0 YES OK
sh4 4.16.7 2.12.0 YES OK
sh4eb 4.16.7 2.12.0 NO (1) OK
sparc_ss10 4.16.7 2.12.0 YES OK
sparc64_sun4u 4.16.7 2.12.0 YES OK
x86 4.16.7 2.12.0 YES OK
x86_64 4.16.7 2.12.0 YES OK
xtensa_lx60 4.16.7 2.12.0 YES OK
xtensa_lx60_nommu 4.16.7 2.12.0 YES OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Kernel patch required, switched to devicetree usage
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
RK3288 Vyasa board support falcon mode in U-Boot and SD layout start from
16MB offset for args and 17MB for uImage. So give full u-boot partition
space as 30M so-that it can occupy bigger uImage file and doesn't overlap
rootfs partition.
[Peter: use # as comment character, clarify comment wording]
Reported-by: Shyam Saini <shyam@amarulasolutions.com>
Tested-by: Shyam Saini <shyam@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shyam saini <shyam@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The kernel now includes the rpi3b+ device tree for aarch64
Signed-off-by: Martin Bark <martin@barkynet.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With this commit we update u-boot version to 2018.05 for
Synopsys boards. U-boot version 2018.05 was released recently
and includes significant changes for ARC boards:
* Fix for compile-time warning for AXS10x
* Add support of platform-specific commands for HSDK
* Add support for on-board SPI flash on HSDK
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use "i.MX8MQ" (in capital letters) for the SoC name for better
readability.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Improve the documentation by adding the configuration of SW801 and SW802
switches for SD card boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
