Wandboard is a low cost iMX6 system consiting of an EDM standard
processor module and a small base board.
http://www.wandboard.org
Signed-off-by: Stephan Hoffmann <sho@relinux.de>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The 3.10.x kernels fail to build with the following message:
vsprintf.c:(.text+0x17e0): relocation truncated to fit: R_AVR32_16N_PCREL against symbol `_ctype' defined in .text section in lib/lib.a(ctype.o)
While this is most likely a toolchain issue, but since AVR32 isn't a
well-maintained architecture, there's not much we can do.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump for a few fixes:
- fix for slow SDcards
- fix for USB interrupts
- fix for tracing functions
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
While at it add the missing network interfaces to configurations that
support it.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Misc fixes and enhancements:
- faster image blitting in framebuffer
- USB fixes, and use of FIQ instead of plain IRQ
- generic ARM fixes for memset
- BT l2cap fix
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Fixes in GPIOs, I2C and DMA.
And since the RPi git tree fork has a non-upstream driver
for rtl8192c WiFi USB stick, there's a fix for that, too.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
[Peter: lock kernel/headers version to 3.9.4, use devtmpfs, add comments]
Signed-off-by: Gregory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
[Peter: adjust for _FEX_FILE]
Signed-off-by: Carlo Caione <carlo.caione@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Add the FW needed for the Cortex M3 on the beaglebone. This is required
for working power management.
Signed-off-by: Anders Darander <anders@chargestorm.se>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
As the beaglebone support is mainlined, there's no support for the old
board setup files, and the only supported run-time configuration is through
the device tree.
We're also setting the kernel headers to follow the 3.8 series.
Signed-off-by: Anders Darander <anders@chargestorm.se>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
This is a configuration that provides a basic setup for generating
bootable nandflash images:
- at91bootstrap
- barebox
- kernel
- rootfs
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
For more info, please read board/telit/evk-pro3/readme.txt
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Some board configs where left out of the u-boot custom version
migration, so do it otherwise they'll just pull the latest version which
might not work and brick the device.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Commit 75b7dc68 ("linux: default to 3.9, remove 3.8") made 3.9 the
default kernel version.
The omap kernel switched to multiplatform kernel during the 3.9 kernel
development cycle. Obviously, the uImage generation doesn't work anymore
with multiplatform kernels, since you have to provide the kernel load
address, resulting in a build error.
Lock down the kernel version to 3.8 to keep the old behaviour until
someone submits a patch to switch to multiplatform kernel.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
the integrator926 defconfig has not been updated for quite some time,
and is still asking for very old linux and u-boot releases. Now that
these versions aren't present in Buildroot anymore, they default to a
newer release, where, in the u-boot case, the defconfig name has
changed, leading to a build failure.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Commit a0b6faa ("gdb: convert to the package infrastructure") changed
the name of the host gdb configuration option, and added it to the
legacy option set, leading to a build breakage for the
armadeus_apf9328_defconfig.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
The IRQ mapping failures have been fixed in 3.8.8 so update it to the
latest kernel series.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Buildroot toolchain, UBIFS rootfs, Linux kernel (board is mainlined since 3.8).
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Somehow the old setting wasn't dropped in 184850a42 (bump u-boot /
linux versions to current stable).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
This is a default configuration for the RaspberryPi, tested and functional.
The kernel used is the one developped by the RaspberryPi foundation as
it's not fully supported currently in mainline kernel. The configuration
used for the kernel is the default bcmrpi.
For more info, please find board/raspberrypi/readme.txt
[Peter: minor README tweaks, rename to readme.txt]
Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
[yann.morin.1998@free.fr: use correct kernel headers, update kernel cset]
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Buildroot toolchain, UBIFS rootfs, Linux kernel (board is mainlined
since 3.8).
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Problematic configurations not bumped:
arm-versatilepb - IRQ failure for symbios scsi
sh4-r2d - Qemu still doesn't emulate advanced features from the UART
sparc-ss10 - Illegal instruction
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Update {ea3250,fdi3250,phy3250}_defconfig to lock down kernel headers to
an appropiate version.
Otherwise the target is building with, at the moment of this writing,
version 3.7 headers and a 2.6.34 kernel which usually isn't wise.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Update to the latest maxim.org.za kernel 2.6.38
Lock down headers version, otherwise we were building a toolchain with
3.7 headers for a 2.6.33 kernel - not too wise.
Also the AT91RM9200 is an ARM920T so enable that target.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Switch to generic V8 optimization for gcc since we dropped the explicit
supersparc one and works just the same.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Bump to use kernel 3.7.1
Switch to hard float toolchain with NEON and VFP support.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
The board boot more fast with a zImage than a uImage
as the kernel will not have to be relocated during the decompression.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Note that this configuration doesn't build entirely: the user must
manually run "make busybox-menuconfig" and disable the "Mount NFS
filesystems" option, because the toolchain does not have RPC support.
This issue will be fixed once the support for toolchain without RPC
will be integrated.
[Peter: fix readme typo]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Notice that you need u-boot >= 2012.04 to be able to boot kernel >= 3.2,
because older u-boots keep the l2 cache enabled, see u-boot commit
679530278 (arm, arm-kirkwood: disable l2c before linux boot) for details.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Update to use the latest kernel 3.5.4.
And also update to the latest .config knobs, otherwise we were just
building a mips(32) target which failed miserably.
This config is still flaky, you get a login prompt but usually fail to
login, passing along an init=/bin/sh helps some but crashes are quite
usual.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Update the qemu samples configs that used kernel 3.3.4 to 3.3.5
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Beautify and lock down kernel version to avoid future issues.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Beautify and lock down kernel version to avoid future issues.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Add new powerpc-mpc8544ds sample qemu config.
Useful for SPE ABI testing.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
This configuration provides a basic setup for using Buildroot
to create all of the images needed for a BeagleBone.
Signed-off-by: Frank Hunleth <fhunleth@troodon-software.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
This is a default configuration for Panda and PandaES, tested on both
platforms.
DEVTMPFS is enabled, to use static dev configuration one would need
to update the generic dev table for ttyO driver.
Panda is well supported in mainline kernel with omap2plus_defconfig,
so this should be safe.
U-boot SPL support is enabled by default as x-loader is now
deprecated.
With OMAP platforms u-boot,img format is prefered now, so it's enabled
by default as well. Also, on PandaBoard, the name of SPL target file
is MLO.
Signed-off-by: Nicolas Dechesne <n-dechesne@ti.com>
Acked-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Bump to use kernel version 3.2.16
Still keep sh4-r2d qemu sample config on 3.2 series since the sh-sci
driver from 3.3 uses unimplemented functionality (as of qemu 1.0.1)
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Target a powerpc 750 rather than the incorrect 440fp to avoid issues and
for correctness.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
[Peter: also add to 9g0dfc]
Signed-off-by: Alexandre Belloni <alexandre.belloni@piout.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
