This patch fixes the DP audio and video PLL configurations for the zynqmp-sm-k26-revA som.
It needs to be applied for both the kv260 and kr260 starter kits.
The Linux DP driver expects the DP to be using the following PLL config:
- DP video PLL should use the VPLL (0x0)
- DP audio PLL should use the RPLL (0x3)
- DP system time clock PLL should use RPLL (0x3)
Register 0xFD1A0070 configures the DP video PLL.
Register 0xFD1A0074 configures the DP audio PLL.
Register 0xFD1A007C configures the DP system time clock PLL.
This patch was build and run tested on a zynqmp-kria-kv260 target board.
Upstream-Status: submitted (https://lore.kernel.org/all/fa7e9abc419c9d7648405d1c62367dbe701d09b8.1652709736.git.michal.simek@amd.com/)
This patch will be removed from buildroot in a future release when no longer necessary.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch fixes an ATF issue by building the ATF for uart1 instead
of uart0 for the Kria KV260 Starter Kit.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The kernel is from upstream with a few extras to reduce the size of
the 'aspeed_g5' zImage because it is too big for the flash layout.
Mainline U-Boot has enough support to load the kernel from the flash
device and from network but it is still behind the OpenBMC branch
where most the development is done.
The main resulting file from the build is a flash image. The partition
layout matches the OpenBMC one for 32M chips. It makes it easier to
update the different partitions from Linux. Intermediate files can be
used to boot from U-Boot over the network or to boot QEMU using
-kernel/-initrd/-dtb.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
The kernel is from upstream and U-Boot is from the OpenBMC branch
because mainline doesn't have the required support for HW, yet.
The main resulting file from the build is a flash image. The partition
layout matches the OpenBMC one for 64M chips. It makes it easier to
update the different partitions from Linux. Intermediate files can be
used to boot from U-boot over the network or to boot QEMU using
-kernel/-initrd/-dtb.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This patch is a temporary fix for the kv260 u-boot.itb generation
until a proper fix has been implemented within u-boot.
The problem is u-boot can only be configured to use the kria k26
som dts configuration at build time, and the kv260 carrier board
overlay is missing from the build. Without this, all of the carrier
board drivers are missing.
This patch will be removed from buildroot once u-boot can build a
correct u-boot.itb for the kria kv260 starter kit including the
carrier board overlay and corresponding drivers:
https://lore.kernel.org/all/20920b0df6b067aca4040459a9677d7d1d6d766a.1615354376.git.viresh.kumar@linaro.org/
Signed-off-by: Neal Frager <neal.frager@xilinx.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
[yann.morin.1998@free.fr: add URL provided by Luca]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This patch enables the zynqmp_kria_kv260_defconfig to auto-generate the
extlinux.conf file.
The board/zynqmp/kria/extlinux.conf and board/zynqmp/kria/post-build.sh have
been removed as they are no longer necessary.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This patch enables the zynqmp_zcu102_defconfig and zynqmp_zcu106_defconfig to
auto-generate the extlinux.conf file.
The board/zynqmp/extlinux.conf has been removed as it is no longer necessary.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
As we're about to remove the nds32 architecture support, remove the
only defconfig that used this CPU architecture.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
With U-Boot 2022.04 gnutls is required for building the hostool
mkeficapsule. Thus the BR2_TARGET_UBOOT_NEEDS_GNUTLS config is needed.
Fixes: https://gitlab.com/buildroot.org/buildroot/-/jobs/2536754543
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump U-Boot to 2022.04 and kernel to 5.15.41 version.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add RISC-V 64-bit nommu defconfig for QEMU virt machine with MMU
disabled.
Unlike qemu_riscv64_virt, qemu_riscv64_nommu_virt does not use OpenSBI,
since the kernel is running in machine mode (M-mode).
After the build is complete, you can start QEMU using the launcher
script:
$ output/images/start-qemu.sh
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since commit [1], the MMU support is mandatory for MMU-capable ARM
cores. This includes the arm926t ARM core used the
qemu_arm_versatile_nommu configuration.
From [2]
"I don't think supporting ARMv5 noMMU makes much sense, as
explained in the commit log. Supporting ARMv7-M definitely makes
sense, but not ARMv5 noMMU."
Remove this defconfig.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/2477067386
[1] 8c925613dc
[2] http://lists.busybox.net/pipermail/buildroot/2022-May/643064.html
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
ppc64 or powernv Linux defconfig fail to build with gcc 11 and/or
binutils 2.37 [1] :
CC kernel/kexec_file.o
Cannot find symbol for section 10: .text.unlikely.
kernel/kexec_file.o: failed
Patches have been sent upstream and should reach Linux 5.18. Until
then, limit binutils to 2.36.1 which doesn't raise the issue.
[1] https://github.com/linuxppc/issues/issues/388
Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Switch U-Boot from vendor downstream version to upstream. Since the
upstream U-Boot uses binman to build the bootable binary (flash.bin) the
need for the iMX specifc prepare script is no longer required.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
[yann.morin.1998@free.fr: we now have 5.17 headers too]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This patch adds support for Xilinx Kria KV260 starter kit.
KV260 features can be found here:
https://www.xilinx.com/products/boards-and-kits/kv260.html
While the Kria SOM is based on a ZynqMP SoC, there are some key
boot config differences from the other ZynqMP evaluation boards.
1. There are no boot switches on Kria SOMs. The boot mode is thus
hard configured for QSPI flash. A pre-programmed boot.bin comes
with every Starter Kit. U-Boot can then find the Linux kernel and
file system on the SD card.
Optional instructions for updating the boot.bin in the QSPI flash
can be found in the readme.txt file and the link below.
https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/1641152513/Kria+K26+SOM
2. Kria SOMs use UART1 for the console instead of UART0. For this
reason, Kria Starter Kits will use a separate extlinux.conf file
from other ZynqMP evaluation boards.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch bumps configs/zynq_xxx_defconfigs to Xilinx software release 2022.1
which includes the following updates:
- U-Boot bumped to 2022.01
- Linux bumped to 5.15.19
- rootfs changed from CPIO to EXT4
- extlinux.conf for distro boot support
- U-Boot migrated from git clone to tarball for faster builds
This patch has been build and run tested on a ZC706 evaluation board.
This patch has been build tested only for zed, microzed and qmtech boards.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch fixes the DP audio and video PLL configurations for the
zynqmp-zcu106-revA evaluation board.
The Linux DP driver expects the DP to be using the following PLL config:
- DP video PLL should use the VPLL (0x0)
- DP audio PLL should use the RPLL (0x3)
Register 0xFD1A0070 configures the DP video PLL.
Register 0xFD1A0074 configures the DP audio PLL.
This patch was build and run tested on a zynqmp-zcu106-revA target board.
Upstream-Status: submitted (https://lore.kernel.org/all/62538b4a04dee28a6fc8ac5b85f8c845a5a76aa4.1651740988.git.michal.simek@amd.com/)
This patch will be removed from buildroot in a future release when no longer necessary.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch bumps configs/zynqmp_zcu106_defconfig pmufw to 2022.1.
The pm_cfg_obj.c has not changed between 2021.2 and 2022.1.
The pmufw_v2022.1.bin has been tested on a zcu106 board.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch bumps configs/zynqmp_zcu102_defconfig pmufw to 2022.1.
The pm_cfg_obj.c has not changed between 2021.2 and 2022.1.
The pmufw_v2022.1.bin has been tested on a zcu102 board.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch migrates configs/zynqmp_zcu106_defconfig to tarballs for TF-A, u-boot and Linux.
This patch has zero change in code running on the device.
The goal is to improve build speed and align with the zynq_xxx_defconfigs.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch migrates configs/zynqmp_zcu102_defconfig to tarballs for TF-A, u-boot and Linux.
This patch has zero change in code running on the device.
The goal is to improve build speed and align with the zynq_xxx_defconfigs.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch bumps configs/zynqmp_zcu106_defconfig to Xilinx software release 2022.1
which includes the following updates:
- TF-A release version 2.6
- U-Boot release version 2022.01
- Linux kernel release version 5.15.19
It is better to use a Xilinx official release version than sha tags.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch bumps configs/zynqmp_zcu102_defconfig to Xilinx software release 2022.1
which includes the following updates:
- TF-A release version 2.6
- U-Boot release version 2022.01
- Linux kernel release version 5.15.19
It is better to use a Xilinx official release version than sha tags.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The update to wilc-firmware added firmware files for WILC3000
devices as a separate config option. All Atmel/Microchip defconfigs
that previously only had WILC1000_FIRMWARE either have WILC3000
Wi-Fi hardware (WILC3000 is the same silicon but with BLE added)
or have the capacity to have either WILC1000 or WILC3000 devices
added to the system. Install all firmware blobs to these devices
by default.
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Update the qemu_xtensa_lx60_nommu_defconfig to use the
busybox-minimal.config.
After commit 3de486f8b0 ("package/busybox: fix udhcpc options in minimal
config"), this has the benefit of fixing the following network
initialization failure:
udhcpc: invalid option -- b
With the full busybox config, the -b option would still be passed and
udhcpc would fail to start for the reason above.
Note that on NOMMU, udhcpc backgrounds unconditionally (unless the -f
option is given), so it still behaves properly. The -b option in fact
only backgrounds after the lease is obtained; on NOMMU, backgrounding is
done before the lease is even requested. So the behaviour is more or
less the same, except that on MMU systems, networking can be considered
either up or not available after S20network, but on NOMMU there is no
such guarantee.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Romain Naour <romain.naour@gmail.com>
Cc: Gerome Burlats <gerome.burlats@smile.fr>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This also removes the dependency to have Python2 installed.
Signed-off-by: Steve Critchlow <scritchlow@bioshall.co.uk>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
The git:// location is no longer supported by github, so change to https://
For more details:
https://github.blog/2021-09-01-improving-git-protocol-security-github/
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch provides defconfig and basic support for Andes
45 series RISC-V architecture on AE350 platform.
http://www.andestech.com/en/products-solutions/andeshape-platforms/ae350-axi-based-platform-pre-integrated-with-n25f-nx25f-a25-ax25/
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Signed-off-by: Alan Kao <alankao@andestech.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Switch to extlinux instead of U-Boot boot script. Drop custom boot
script and genimage config. Instead use common orangepi files from
board/orangepi/common. To help extlinux to find DTB without U-Boot
environment changes, do not strip arm64 board specific directory
from DTB name when installing it in /boot directory. For this
purpose use BR2_KERNEL_DTB_KEEP_DIRNAME config option. Finally,
tidy up configuration file adding section names.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
- Bump Linux to version 5.4.137
- Bump U-Boot to add new targets, version remains the same
- Drop BR2_ROOTFS_OVERLAY and remove S09modload script because it was
only used by PFE and now PFE is loaded directly by the kernel
- Use Image.gz instead of Image to have a compressed kernel
- Rename ucls1012a.its to br2-ucls1012a.its since post-build.sh and
post-image.sh use different name. This fixes the bug that didn't
allow the creation of the part0-000000.itb file.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Changes:
* Switch to common orangepi scenario for multiple boards (board/orangepi/common) to create an SD image.
* Exclude FAT partition, it is no longer needed for U-Boot.
* Switch SD image from MBR to GPT for partition-uuid to work.
* Switch to extlinux, this is convenient for debugging.
Signed-off-by: Sergey Kuzminov <kuzminov.sergey81@gmail.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Technologic Systems has rebranded as embeddedTS with the current
domain eventually going offline. Update web/doc URLs to correct
resource locations.
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Commit 616ba9c90b extended rootfs size, but
forgot to add quotes around it. Thus, kconfig removed the option
entirely.
While we're at it, move the option to a more appropriate place together
with the rest of the ext2 options.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/2103784289
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add a U-Boot config fragment to set the correct control device tree file for
each board, rather than using the default (zcu100).
Signed-off-by: Neal Frager <neal.frager@xilinx.com>
Tested-by: Peter Korsgaard <peter@korsgaard.com>
[Peter: reword commit message, rename fragment files]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Fixes the following compile error:
In file included from include/bootm.h:10,
from tools/image-host.c:12:
include/image.h:1178:12: fatal error: openssl/evp.h: No such file or directory
1178 | # include <openssl/evp.h>
| ^~~~~~~~~~~~~~~
compilation terminated.
Fixes: https://gitlab.com/buildroot.org/buildroot/-/jobs/2103784200
Signed-off-by: Marcus Hoffmann <marcus.hoffmann@othermo.de>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
