Add initial support for Orangepi One Plus board with below features:
- U-Boot 2018.09
- Linux 4.19.0-rc8
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently, U-Boot is failing to build, due to some issues
with the toolchain and the U-Boot port.
Fix it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
New generic defconfig for aarch64, to run on aarch64 servers compliant
with EFI firmware and ACPI.
This can also be tested with qemu, and is useful so that we have an
arm defconfig with grub enabled. Tested with qemu 2.11.2 and AAVMF,
the aarch64 virtual machine UEFI firmware.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
[Thomas: extend readme.txt with more details]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
4.18 brought cpufreq support for H3, but sunxi_defconfig does not enable the
ondemand cpufreq govenor so the frequency is dynamically adjusted - So
enable it in linux-extra.config.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
4.18 brought cpufreq support for H3, but sunxi_defconfig does not enable the
driver for the sy8106a regulator used on the board or enable the ondemand
cpufreq govenor so the frequency is dynamically adjusted - So enable these in
linux.fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The default ORC unwinder requires libelf to be built. While we could
build libelf using BR2_LINUX_KERNEL_NEEDS_HOST_LIBELF, we probably
don't really need the ORC unwinder in the PC defconfigs, so let's use
the frame pointer unwinder instead.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/123771107
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the kernel and U-Boot versions to the actual versions in use.
Update the description of supported hardware features.
Add a note that the stale SPI flash environment issue only affects the
vendor BSP.
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to version 2018.11. This version supports autodetection of
SD/eMMC boot source, so we can now enable environment load from SD card.
Add a U-Boot kconfig fragment that sets SD/eMMC as environment load/save
device. This avoids stale environment values from the SPI flash. That in
turn, allows to use the more convenient distro boot which is enabled in
the default environment.
Bump kernel to version 4.19.2. This version enables
CONFIG_PHY_MVEBU_CP110_COMPHY in the arm64 defconfig, so remove it from
the kernel kconfig fragment. Enable support for SFP modules detection
and configuration. Leave the PHY drivers for now to keep them built into
the kernel. The kernel defconfig builds these drivers as modules. But
that does not work as expected in the default configuration.
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Amarula A64-Relic board has AP6330 WiFi/BT combo, but does
not have ethernet port. So it makes sense to enable wireless
networking by default:
- add broadcom wireless firmware package to image
- add basic wireless tools to image
- add rootfs overlay with proper NVRAM file for on-board AP6330 chip
- add mdev to image to enable module autoloading
- update readme.txt to test wifi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Amarula A64-Relic board
with below features:
- U-Boot 2018.07
- Linux 4.17.0-rc6
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas: add missing BR2_TARGET_UBOOT_NEEDS_PYLIBFDT=y and
BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y options.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Some ZynqMP device trees in the kernel have a dot in their name,
for example "zynqmp-zcu102-rev1.0". The post image script
left out the part after the dot and created an invalid symlink.
Signed-off-by: Francois Beerten <fbeerten.git@colabti.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch provides support for the board Odroid XU4. It uses a recent
4.14 kernel released by Hardkernel, and the current u-boot 2017.05
also from Hardkernel.
Signed-off-by: Pierre CROKAERT <pct@crookies.net>
[Thomas:
- Update DEVELOPERS file
- Update .gitlab-ci.yml file
- Simplify the boot.ini script
- Add missing BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_14 option
- Add BR2_PACKAGE_HOST_DOSFSTOOLS and BR2_PACKAGE_HOST_MTOOLS since a
VFAT filesystem is generated
- Keep the default root filesystem size, since it is sufficient.
- Reduce the size of the VFAT filesystem]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add intial support for Bananapi M2 Ultra board based on the Allwinner
R40 SoC.
- U-Boot 2018.07
- Linux 4.18.12
Board specifications: http://www.banana-pi.org/m2u.html
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add RISC-V 64-bit defconfig for QEMU virt machine.
Tested with QEMU 2.12.1
Signed-off-by: Mark Corbin <mark.corbin@embecosm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit renames olimex_a20_olinuxino_lime_mali to
olimex_a20_olinuxino_lime_legacy, because the upstream Linux kernel
now also supports using the Mali GPU.
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch removes duplicate messages in Linux log on HSDK board.
For HSDK board we setup bootargs via device tree,
see https://elixir.bootlin.com/linux/latest/source/arch/arc/boot/dts/hsdk.dts#L25
"console=ttyS3" was mistakenly placed in u-boot bootargs which are
appended to Kernel bootargs in case of using buildin .dtb.
Before patch log is like:
------------------------8<-------------------------------------
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz,...
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz,...
mmc0: new SDHC card at address 59b4
mmc0: new SDHC card at address 59b4
blk_queue_max_segment_size: set to minimum 8192
blk_queue_max_segment_size: set to minimum 8192
------------------------>8-------------------------------------
After patch log is like:
------------------------8<-------------------------------------
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz,...
mmc0: new SDHC card at address 59b4
blk_queue_max_segment_size: set to minimum 8192
------------------------8<-------------------------------------
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Resurrect support for RIoTboard after 2018.02.x deprecation.
Signed-off-by: Nikolay Dimitrov <nikolay.dimitrov@retrohub.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
At first the support for i.MX8MQ processors was minimal, hence this
section in the readme file.
Since then, GPU support was added [1] in master and VPU in next [2].
So drop this section as it is confusing people and no one maintains it.
[1] https://git.buildroot.net/buildroot/commit/?id=84afda9c
[2] https://git.buildroot.net/buildroot/commit/?id=82732071
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
512B is not a correct size to express "512 bytes", and causes a
genimage failure:
ERROR: Invalid size suffix 'B' in '512B'
To express "512 bytes", using just "512" is sufficient. With this
commit, genimage works fine, and we indeed have a 512 bytes unused
partition:
$ fdisk -l output/images/sdcard.img
Disk output/images/sdcard.img: 60 MiB, 62915584 bytes, 122882 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x00000000
Device Boot Start End Sectors Size Id Type
output/images/sdcard.img1 1 1 1 512B 0 Empty
output/images/sdcard.img2 2 524289 524288 256M 83 Linux
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/88314963
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
As for sh4-r2d (little-endian) restore the old sh-sci driver behaviour
for sh4eb-r2d.
Tested with qemu_sh4eb_r2d_defconfig.
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This reverts commit 18e8cf159177100e69d528293f8cf6875c0b1bca (kernel)
The last Qemu kernel update [1] introduced a regresion in sh4 SCIF
serial device. Some keyboard presses are very slow to be taken into
account, perhaps not even taken into account at all. This would
explain why our test infrastructure doesn’t manage to login as root
[2][3][4].
git bisect reported a kernel patch from 4.11, increasing RX FIFO
trigger defaults value for sh-sci (H)SCIF. The kernel patch itself
looks good but the Qemu emulation is not ready to handle this new
setting.
>From Qemu (2.12.0): target/sh4/README.sh4
"Configuration of the second serial port (SCIF) is supported. FIFO
handling infrastructure has been started but is not completed yet."
We can't use the first serial port (ttySC0) because it's the second
SH UART that's emulated by Qemu.
In order to be able to test sh4 architecture with newer kernel,
revert to the old behaviour.
[1] 03fb00f217
[2] https://gitlab.com/free-electrons/toolchains-builder/-/jobs/72006425
[3] https://gitlab.com/free-electrons/toolchains-builder/-/jobs/72006427
[4] https://gitlab.com/free-electrons/toolchains-builder/-/jobs/72006426
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
U-Boot SPL configures pinmuxes, clocks and other low-level devices. On
the Xilinx ZynqMP SoCs the code to do this resides in a file called
psu_init_gpl.c which is initially generated by the Xilinx development
tools. Add an option to pass these files from the outside (e.g. in the
board files).
For this to work properly, a patch to U-Boot is needed. However this
patch must be applied by each defconfig using
BR2_TARGET_UBOOT_ZYNQMP_PSU_INIT_DIR. If it were in boot/uboot/ to be
applied unconditionally, it would break the build for configs using a
U-Boot version where the patch is already applied.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Reviewed-by: Joel Carlson <JoelsonCarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
[Thomas: add comment about U-Boot version requirements to use this
option.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This adds support the Xilinx ZCU106 development board.
[Tested on the ES2 (Engineering Sample 2) version of the board]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
In order to boot on the Xilinx ZynqMP SoCs, U-Boot SPL requires a
recent PMU firmware loaded. Instruct U-Boot to add pmufw.bin to the
boot.bin file together with U-Boot SPL, and the boot ROM will load
both.
For this to work properly, a patch to U-Boot is needed. However this
patch must be applied by each defconfig that wishes to use
BR2_TARGET_UBOOT_ZYNQMP_PMUFW. If it were in boot/uboot/ to be applied
unconditionally, it would break the build for configs using a U-Boot
version higher than 2018.7-rc1 where the patch is already applied.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Reviewed-by: Joel Carlson <JoelsonCarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
[Thomas:
- indicate that this feature requires U-Boot 2018.07, since commit
c7df098a71e05dc81cee818747759e8060b59626 is needed.
- define UBOOT_ZYNQMP_KCONFIG_PMUFW only once, and instead use a
variable named UBOOT_ZYNQMP_PMUFW_PATH to store the path to the PMU
firmware]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Use proper ARCH for mkimage command
- Use different U-Boot binary name depending on ARCH
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
6x_bootscript/6x_upgrade have been deprecated for more than a year.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The upgrade.cmd script expects the binary to be named
u-boot.<uboot_defconfig>.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Allow user to override the hardcoded dtb name by using
BR2_ROOTFS_POST_SCRIPT_ARGS.
The only user of this script, configs/freescale_imx8mqevk, is updated
accordingly.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for flashing the u-boot-dtb.imx binary in the SD card
when a target selects BR2_TARGET_UBOOT_FORMAT_DTB_IMX.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The 2017 MinnowBoard Turbot skews no longer use the Realtek 8169
Ethernet chip. The Turbot D0 uses The Intel I211, the Turbot Dual
Ethernet has an I210 (quad-core) or I211 (dual-core).
Add CONFIG_IGB to the Linux config but keep the Realtek 8169 support
to avoid breaking older boards
Tested on Turbot D0, lspci -k shows the igb driver is used:
03:00.0 Class 0200: 8086:1539 igb
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add a defconfig for the Olimex A10-OLinuXino-LIME, reusing most
of the A20-OLinuXino-Lime and A13-OLinuXino files (sym links).
The configurations for Olimex A10-OLinuXino-LIME feature:
- U-Boot 2018.03
- Mainline Linux kernel 4.14.26
Signed-off-by: Leon Anavi <leon.anavi@konsulko.com>
[Arnout: remove commented-out BR2_ARM_EABIHF=y (which is default)]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
As per latest Raspberry Pi firmware documentation, the option
'arm_control' has been deprecated in favor of 'arm_64bit'.
Fixes https://bugs.busybox.net/show_bug.cgi?id=11111.
Signed-off-by: Jason Tang <tang@jtang.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the kernel version to 4.17.2.
Update U-Boot version to 2018.05.
Migrate to U-Boot generic distro configuration which is easier than the
hand written boot script.
Improve the 'dd' command example in readme.txt.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
To not maintain custom copy of inittab file lets adopt approach
used in raspberrypi adding post-build script for synopsys/axs10x
boards.
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Apply modifications made in recent commits:
- 456ea9871e busybox: add /dev/std{in, out, err} symlinks to inittab
- 13dbe73782 busybox: reduce number of mkdir calls in inittab
- 8a89d290d4 busybox: add an inittab entry to activate swap
Signed-off-by: Carlos Santos <casantos@datacom.com.br>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
4.17 brings support for HDMI out, but sunxi_defconfig hasn't been updated to
enable the drivers - So add a kernel fragment to enable them.
Likewise, analog audio has been supported since 4.10, but the driver isn't
enabled in sunxi_defconfig, so enable it in the fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump kernel to version 4.17 and U-Boot to 2018.05.
As the dtb file has been renamed in mainline, make the necessary
adjustments in U-Boot environment and also in
BR2_LINUX_KERNEL_INTREE_DTS_NAME.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump kernel to version 4.17 and U-Boot to 2018.05.
As the imx_v6_v7_defconfig in 4.17 already selects the
CONFIG_CFG80211_WEXT option, the linux.fragment can
be simply removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump linux as well headers to v4.16 version, this eventually drop the
wifi patch since it has been merged to Linux v4.16.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
All linux configs are renamed to a version neutral filename
to avoid further renaming on kernel bumps.
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.16.7 2.12.0 YES OK
arm_versatile 4.16.7 2.12.0 YES OK
arm_versatile_nommu 4.16.7 2.12.0 YES OK (3)
arm_vexpress 4.16.7 2.12.0 YES OK
m68k_mcf5208 4.16.7 2.12.0 YES OK
m68k_q800 4.16.7 q800-v2.11.0 NO (2) OK
microblazebe 4.16.7 2.12.0 YES OK
microblazeel 4.16.7 2.12.0 YES OK
mips32r2el_malta 4.16.7 2.12.0 YES OK
mips32r2_malta 4.16.7 2.12.0 YES OK
mips32r6el_malta 4.16.7 2.12.0 YES OK
mips32r6_malta 4.16.7 2.12.0 YES OK
mips64el_malta 4.16.7 2.12.0 YES OK
mips64_malta 4.16.7 2.12.0 YES OK
mips64r6el_malta 4.16.7 2.12.0 YES OK
mips64r6_malta 4.16.7 2.12.0 YES OK
nios2-10m50 4.16.7 2.12.0 NO OK
or1k 4.16.7 2.12.0 NO OK
ppc_g3beige 4.16.7 2.12.0 YES OK
ppc_mpc8544ds 4.16.7 2.12.0 YES OK
ppc_virtex_ml507 4.16.7 2.12.0 NO OK
ppc64_pseries 4.16.7 2.12.0 YES OK
ppc64le_pseries 4.16.7 2.12.0 YES OK
ppc64_e5500 4.16.7 2.12.0 YES OK
sh4 4.16.7 2.12.0 YES OK
sh4eb 4.16.7 2.12.0 NO (1) OK
sparc_ss10 4.16.7 2.12.0 YES OK
sparc64_sun4u 4.16.7 2.12.0 YES OK
x86 4.16.7 2.12.0 YES OK
x86_64 4.16.7 2.12.0 YES OK
xtensa_lx60 4.16.7 2.12.0 YES OK
xtensa_lx60_nommu 4.16.7 2.12.0 YES OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Kernel patch required, switched to devicetree usage
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
RK3288 Vyasa board support falcon mode in U-Boot and SD layout start from
16MB offset for args and 17MB for uImage. So give full u-boot partition
space as 30M so-that it can occupy bigger uImage file and doesn't overlap
rootfs partition.
[Peter: use # as comment character, clarify comment wording]
Reported-by: Shyam Saini <shyam@amarulasolutions.com>
Tested-by: Shyam Saini <shyam@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shyam saini <shyam@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The kernel now includes the rpi3b+ device tree for aarch64
Signed-off-by: Martin Bark <martin@barkynet.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With this commit we update u-boot version to 2018.05 for
Synopsys boards. U-boot version 2018.05 was released recently
and includes significant changes for ARC boards:
* Fix for compile-time warning for AXS10x
* Add support of platform-specific commands for HSDK
* Add support for on-board SPI flash on HSDK
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use "i.MX8MQ" (in capital letters) for the SoC name for better
readability.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Improve the documentation by adding the configuration of SW801 and SW802
switches for SD card boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently this target fails to build:
arch/arm/mach-imx/built-in.o: In function `init_mmdc_lpddr2_settings':
platform-spi_imx.c:(.text+0x8f18): undefined reference to `imx6sll_lpddr2_freq_change'
arch/arm/mach-imx/built-in.o: In function `imx6ul_cpuidle_init':
platform-spi_imx.c:(.init.text+0x195c): undefined reference to `mx6ull_lpm_wfi_end'
platform-spi_imx.c:(.init.text+0x1960): undefined reference to `mx6ull_lpm_wfi_start'
platform-spi_imx.c:(.init.text+0x1964): undefined reference to `imx6ull_low_power_idle'
arch/arm/mach-imx/built-in.o: In function `imx6sl_init_late':
platform-spi_imx.c:(.init.text+0x56f0): undefined reference to `imx6sll_cpuidle_init'
Makefile:969: recipe for target 'vmlinux' failed
NXP 4.9 kernel does not properly support mx31, so better remove this target.
mx31_3stack board is currently supported in U-Boot and kernel mainline,
so if someone is interested on this board, then a target can be introduced
later which uses these mainline components.
Currently I do not have access to this board, so remove it its defconfig
for now.
Fixes: https://gitlab.com/buildroot.org/buildroot/-/jobs/66561688
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As we are about to remove the Blackfin architecture, remove the only
defconfig that was using this CPU architecture.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit adds a genimage template file that is used for i.MX8
platforms in the common i.MX post-image script.
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit adds an imx8-bootloader-prepare.sh script that will be
used by i.MX8 platforms to prepare their bootloader image.
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit makes the common post-image.sh script used by Freescale
platforms compatible with arm64:
- Support having DTBs in sub-folders
- Support a kernel image in the 'Image' format
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adds support for the at91sam9g20-ek board to the flasher.sh script.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support to the flasher.sh script for the at91sam9260-ek board which
complements the existing at91sam9260eknf_defconfig.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Instead of using the install of sam-ba under host/opt directly, use the symlink
created in host/bin. The side effect of doing this instead allows the correct
sam-ba binary to be used based on the host arch being 32 bit or 64 bit.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Resolves an error in the way the bootlin toolchain-builder uses
the board/qemu/ppc64-e5500/readme.txt to generate the qemu test
command.
https://github.com/free-electrons/toolchains-builder/blob/master/build.sh#L186
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Switch to Linux kernel version 4.9.59 from the TI SDK 04.02.00.09
(TI SDK release date: 23.12.2017)
Updated uboot to version 2018.01
uEnv.txt corrected to boot from sd card on the ti-am335x-evm
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adding basic support modeled after the Freescale/NXP T1040RDBD4 board.
This target is used to support testing of the bootlin e5500 toolchain.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
[Thomas: update .gitlab-ci.yml.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
My goal was to rely on upstreamed features as much as possible, which
means that some bits are only half-baked for now:
- Due to the DTS restructuring in upstream kernel, we require 4.11+. The
latest LTS or CIP kernels do not know about the -Base model.
- Linux has no generic support for SFP cages (yet). It seems that this
has hit the net-next tree in August 2017, but there's been no release
(it's probably targettting 4.14). Also, the merge only included the
required infrastructure; the mvneta driver conversion is not included.
Patches which finalize this exist in Russel King's tree and also in
random vendor trees.
- There's no access to the SPI flash in these versions of
uboot/linux/dts.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
[Arnout:
- rename to solidrun_clearfog_defconfig;
- specify kernel headers version (default is now 4.15);
- remove ext2 fs size override, the 4 extra MB are not needed;
- U-Boot needs dtc and openssl;
- add comments to defconfig;
- update .gitlab-ci.yml;
- mention in readme.txt that SFP support is missing;
- add Jan to DEVELOPERS.
]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Synopsys DesignWare HSDK (which stands for ARC HS
Development Kit) is the latest and greatest development
platform that sports quad-core ARC HS38 in real silicon.
Most noticeable features of the board are:
* Quad-core ARC HS38 CPU running at 1GHz
* 4Gb of DDR
* Built-in Vivante GPU (well supported via open source
Etnaviv drivers)
* Built-in Wi-Fi/Bluetooth module (RedPine RS-9113)
And as usual we have:
* [micro] SD-card slot
* 2 USB 2.0 ports
* 1Gbit Ethernet port
* Built-in Digilent JTAG probe
* Serial port accessible via micro-USB port
Writing sdcard.img on SDcard creates two partitions:
* FAT32 with uImage and uboot.env
* EXT4 with root filesystem
We modify kernel config because in default hsdk kernel config
CONFIG_INITRAMFS_SOURCE parameter is set and when we build
rootfs separately (BR2_TARGET_ROOTFS_INITRAMFS is not set)
error appears. Also we set up CONFIG_ARC_UBOOT_SUPPORT which
enables usage of uboot variables in the boot process.
[Peter: Fix comments and rename defconfig to snps_archs38_hsdk_defconfig,
Add defconfig to DEVELOPERS and fixup board/synopsys entry,
Drop postimage script, rename env file in genimage.cfg and drop size
setting for rootfs partition,
Add "" for CONFIG_INITRAMFS_SOURCE in linux fragment]
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-buildroot@synopsys.com
Reviewed-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Up to now, Raspberry Pi Zero W (rpi0w) could be built with the normal
raspberrypi0_defconfig. However, then you don't have support for the
Bluetooth out-of-the-box, which makes using a W a bit pointless.
Therefore, create a separate defconfig for the W. It is a copy of
raspberrypi0_defconfig with the following changes:
- Add DT overlays (from rpi-firmware) to support Bluetooth.
- Pass --add-pi3-miniuart-bt-overlay to post-image.sh.
Since there is now a separate raspberrypi0w_defconfig, the W support
can be removed from raspberrypi0_defconfig.
Signed-off-by: Yves Deweerdt <yves.deweerdt.linux@gmail.com>
[Arnout:
- Bump to same kernel version as raspberrypi0.
- Remove redundant comment.
- Remove redundant default BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS=y.
- Improve commit log.
- Refresh .gitlab-ci.yml.
]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
The uCLS1012A-SOM product family (ucls1012a) is an Arcturus Networks Inc.
64bit ARM Cortex-A53 class System on Module powered by a NXP QorIQ LS1012A
Low Power Communication Processor. This 314 pin MXM3.0/SMARC module card
contains DDR3, QSPI NOR Flash, eMMC NAND Flash, optional Audio CODEC and is
available with 1 or 2 Gig-Ethernet PHYs.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Changes v1 -> v2:
- updated kernel and u-boot source repositories to github
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Sometimes imximage throws the following error:
MKIMAGE u-boot-dtb.imx
Error: No BOOT_FROM tag in board/freescale/mx6sxsabresd/imximage.cfg.cfgtmp
arch/arm/imx-common/Makefile:91: recipe for target 'u-boot-dtb.imx' failed
Later on, when running mkimage for the u-boot.imx it will succeed in
finding the IVT offset.
Looks like some race condition happening during parallel build when
processing mkimage for u-boot-dtb.imx and u-boot.imx.
A proper fix still needs to be implemented, but as a workaround let's
remove the error when the IVT offset is not found.
It is useful to have such message, especially during bring-up phase,
but the build error that it causes is severe, so better avoid the
build error for now.
The error checking can be re-implemented later when we have a proper
fix.
This workaround has already been applied in mainline U-Boot:
http://git.denx.de/?p=u-boot.git;a=commit;h=b5b0e4e351e20a606de22db6a56ad6bc1e2aa8fd
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/59015347
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The T1 QoriQ from NXP has had a few varients of RDB dev boards.
This target is against the latest D4RDB version. Any of the
other versions before D4RDB (plain RDB), may require backing off
the uboot version to SDK 1.6 and/or adjusting the kernel dtb used.
This board configuration provides an upstream kernel build which
has been verified to boot on target.
The target assumes the user still uses the NXP suggested prebuilts
in the SDK2.0 (last release for PowerPC). If a uboot rebuild is
required, the source for SDK2.0 can be found in the following repo.
http://git.freescale.com/git/cgit.cgi/ppc/sdk/u-boot.git/tag/?id=fsl-sdk-v2.0-1703
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Replacing the p1010rdb, this board is based on the tower development
system still available by NXP. The board is setup to track upstream
Linux and has been bumped from 4.1 to 4.15 (compared to p1010).
The target does not build uboot and assumes the user still uses the NXP
suggested prebuilts in the SDK2.0 (last release for PowerPC). If a
uboot is required, the source for SDK2.0 can be found in the following
repo.
http://git.freescale.com/git/cgit.cgi/ppc/sdk/u-boot.git/tag/?id=fsl-sdk-v2.0-1703
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Rename the confusing and misleading ts5x00 directory to a real reference
platform name, ts5500. The readme.txt file already states the support
for both TS-5500 and TS-5400 platforms.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump the 3.17 kernel used for the Technologic Systems TS-5500 platform
to the latest LTS kernel 4.14.
This fixes the ts5x00_defconfig build with GCC 6.x.
The linux-3.17.config file has been renamed to linux-4.14.config to
match the new kernel version, and its changes are the result of make
linux-update-defconfig. However only comments are affected.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig fails to build with gcc 6.x, even though we switched to
using gcc 6.x as the default gcc version in May 2017.
This defconfig also hasn't seen any non-mechanical update since
November 2015.
So it's time to get rid of it, in order to remove the following build
failure:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306938
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig fails to build with gcc 6.x, even though we switched to
using gcc 6.x as the default gcc version in May 2017.
It hasn't been updated since April 2017, and the original submitter,
Fabio Porcedda said:
Unfortunately a newer kernel doesn't boot and I don't have the time
to fix the issue. If having a defconfig that doesn't build on gcc
6.x is unacceptable feel free to remove it.
So, let's get rid of this defconfig, which will remove the following
build error:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306952
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Wireless support ends up enabling CONFIG_SYSTEM_TRUSTED_KEYRING, which
requires openssl to be available on the host, so disable wireless
support, which isn't needed in Qemu.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The ORC unwinder requires libelf to be available on the host, so use
the frame pointer unwinder instead. Using the frame pointer unwinder
is probably good enough in our default Qemu configurations.
Wireless support ends up enabling CONFIG_SYSTEM_TRUSTED_KEYRING, which
requires openssl to be available on the host, so disable wireless
support, which isn't needed in Qemu.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig currently doesn't build with GCC6 (Linux 4.1).
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306827
A maintainer w/board isn't available to make updates, so removing
this config.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
>From the original submitter of this defconfig:
"""
I no longer have access to ci40 board. It would be difficult for me to
maintain it.
"""
And this defconfig currently fails to build with gcc 6.x. Therefore,
drop it.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306806
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
No other changes necessary, 4.15 builds and boots fine.
Signed-off-by: Alex Suykov <alex.suykov@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig currently fails to build the Linux kernel:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306826
In addition, the U-Boot build had already been removed in commit
12c01e4a05
("configs/freescale_mpc8315erdb: remove U-Boot build"), back in
October 2016, and nobody bothered fixing it.
This defconfig was originally contributed and maintained by Gustavo
Zacarias, but he is no longer active in Buildroot, and nobody
expressed interest in this defconfig, so let's get rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
In particular:
- Explicitly specify the CPU to be used, POWER8, which matches
qemu_ppc64le_pseries_defconfig
- Use hard disk emulation to access the root filesystem instead of an
initrd.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This allows the toolchain building machinery used by
https://toolchains.bootlin.com to automatically re-use this Qemu
command line.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
qemu-system-ppc64le doesn't necessarily exist: it isn't installed by
Qemu, and only created as a symlink to qemu-system-ppc64 by some
distributions (Ubuntu). Other distributions (Fedora) just have
qemu-system-ppc64.
But qemu-system-ppc64 is capable of running little-endian PPC64
systems, so use this one instead.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Orange-Pi Zero Plus2 board has AP6212 WiFi/BT combo, but does
not have ethernet port. So it makes sense to enable wireless
networking by default:
- add DTS patch enabling AP6212 WiFi/BT combo support
-- this patch is on its way to mainline Linux v4.16
- enable WiFi support in kernel config
- enable Broadcom brcmfmac kernel driver in kernel config
- add Broadcom wireless firmware package to image
- add basic wireless tools to image
- add mdev to image to enable module autoloading
- add rootfs overlay with proper NVRAM file for on-board AP6212 chip
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump versions:
- use U-Boot 2008.01
- use Linux kernel v4.15.2
Drop patch with dts sdcard fix since it has been
merged to Linux v4.15.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With this commit we update Linux kernel version to 4.15 and
Linux headers version to 4.15.
Also patches for arc vdk are removed because these
changes were applied in Linux 4.15.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump Linux to 4.15 and U-Boot to 2018.01. Remove networking dts patches
since they has landed in Linux 4.15. Update readme.txt: fix mainline BSP
versions and update boot selection for board rev 1.3.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add a genimage.cfg to create a working sdcard.img for the ci20
hardware. We also need a uboot-env.txt to create the partition for
the uboot environment.
Update the board/ci20/readme.txt with the related information. Remove
the tftp netboot description from the readme as it is already to
complicated for a basic bootable example.
Signed-off-by: Johannes Schmitz <johannes.schmitz1@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Currently in Orange Pi boards post-build script is used only to generate
U-Boot boot script and post-image script is used only to generate sdcard
image according to genimage configuration. However both those tasks can
now be handled by generic Buildroot tools:
- BR2_TARGET_UBOOT_BOOT_SCRIPT config options
- support/scripts/genimage.sh script
This patch drops custom scripts replacing them
by generic Buildroot tools.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also include new boot scripts to match standard distro uboot commands.
Our previous 6x_bootscript and 6x_upgrade used custom variables and
their naming don't make sense now that we target more than i.MX6 CPU.
Therefore those old scripts are marked as legacy and kept for now but
the goal is to deprecate and remove them later.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also switch repository from old freescale site to codeaurora:
https://source.codeaurora.org/external/imx/
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Orangepi PC2
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Zero Plus2
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Prime
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Win/Win Plus
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Olimex A64-OLinuXino
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Tsvetan Usunov <usunov@olimex.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for FriendlyARM Nanopi NEO2 board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Yuefei <yftan@friendlyarm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for FriendlyARM Nanopi A64
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Yuefei <yftan@friendlyarm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for SoPine board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: TL Lim <tllim@pine64.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Pine64 board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: TL Lim <tllim@pine64.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for bananapi M64 board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Jason <manager@sinovoip.com.cn>
Cc: hailymei@banana-pi.com <hailymei@banana-pi.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add MacchiatoBin board by SolidRun. This board is based on Marvell
Armada 8040 SoC. Board support package includes the following
two options: mainline and vendor BSPs.
Mainline BSP:
- Marvell ATF v1.3-armada-17.10
- mainline U-Boot v2017.11
- mainline Linux kernel v4.14.4
Marvell BSP with more hardware support enabled:
- Marvell ATF v1.3-armada-17.10
- Marvell U-Boot based on v2017.03
- Marvell Linux kernel based v4.4.52
More details about this board are available on wiki:
- http://wiki.macchiatobin.net
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
[Thomas: misc tweaks in readme.txt.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Run-time tested on ZedBoard, build-tested on the other boards]
[Peter: also add host-dosfstools / host-mtools to make vfat images]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
We are about to introduce genimage support for the Zynq boards. For
all of them U-Boot loads the DTB from a file named "devicetree.dtb" so
we need to rename it on the SD card image.
We could use genimage itself to rename files while creating the
image. But this would require a different genimage.cfg for each board,
leading to duplicate code.
Instead let's create a "devicetree.dtb" symlink pointing to the dtb
listed in the configuration. Currently all the Zynq-based boards have
only one DTS configured, but if one had two or more of them, the
symlink would point to the first one.
[Peter: only create symlink if dtb option is available]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This board is quite similar to orangepi-one board. Instead of ethernet, it
has RTL8189FTV SDIO WiFi chip.
Board support package includes the following components:
- mainline u-boot 2017.09
- mainline kernel 4.13.11
Signed-off-by: Jan Kraval <jan.kraval@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This board is a variant of orangepi-pc board. It adds 8GB eMMC and Realtek
RTL8189FTV SDIO WiFi chip. This variant has a separate support in U-Boot
and kernel. So it makes sense to create a separate entry
for this board in buildroot.
Board support package includes the following components:
- mainline u-boot 2017.09
- mainline kernel 4.13.11
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
[Thomas: add entry to DEVELOPERS file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This merges the next branch accumulated during the 2017.11 release
cycle back into the master branch.
A few conflicts had to be resolved:
- In the DEVELOPERS file, because Fabrice Fontaine was added as a
developer for libupnp in master, and for libupnp18 in
next. Resolution is simple: add him for both.
- linux/Config.in, because we updated the 4.13.x release used by
default in master, while we moved to 4.14 in next. Resolution: use
4.14.
- package/libupnp/libupnp.hash: a hash for the license file was added
in master, while the package was bumped into next. Resolution: keep
the hash for the license file, and keep the hash for the newest
version of libupnp.
- package/linux-headers/Config.in.host: default version of the kernel
headers for 4.13 was bumped to the latest 4.13.x in master, but was
changed to 4.14 in next. Resolution: use 4.14.
- package/samba4/: samba was bumped to 4.6.11 in master for security
reasons, but was bumped to 4.7.3 in next. Resolution: keep 4.7.3.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Or1k support improved, f.e. musl can be tested inside qemu.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This helps the toolchains.free-electrons.com build logic re-use
directly the Qemu command lines from this readme.txt file, by having a
-append option similar to the ones used in other readme.txt files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This helps the toolchains.free-electrons.com build logic re-use
directly the Qemu command lines from this readme.txt file, by having a
-append option similar to the ones used in other readme.txt files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6ulevk_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As there is now a defconfig inside kernel sources for mxs platforms, use it.
Signed-off-by: Julien BOIBESSOT <julien.boibessot@armadeus.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This updates the LEGO MINDSTORMS EV3 board to Linux kernel 4.14 and
U-Boot 2017.11.
* Kernel patches are dropped because they are in mainline now.
* This caused the kernel image to be >3M so some adjustments to the image
sizes/layout needed to be made in U-Boot.
* Updated U-Boot version bumped since we are touching this config anyway
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6sx-sdb_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6slevk_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
boot.cmd using dts file instead of dtb which was
added in below commit, so fix the same.
"board: Add Bananapi M1 support"
(sha1: 5f50fb8d1d)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add some documentation about running the pc defconfigs in qemu.
In particular, document the use of the -bios parameter to use the OVMF
firmware to test the UEFI image.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This simplifies the pc configs and respective post image scripts to use
the shared genimage script and separate grub config files.
Separate grub files are cleaner to maintain and easier to copy and
modify, for example to support booting the pc defconfigs in qemu.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for bananapi M1 board with below features:
- U-Boot 2017.09
- Linux 4.13.7
- Default packages from buildroot
Cc: Jason <manager@sinovoip.com.cn>
Cc: hailymei@banana-pi.com <hailymei@banana-pi.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The gpu_mem option is not using the proper option argument which causes sed to
fail.
+ case "${arg}" in
+ gpu_mem=ome/gportay/output-rpi3-qtwe/images
+ sed -e '/^ome/gportay/output-rpi3-qtwe/images=/s,=.*,=ome/gportay/output-rpi3-qtwe/images,' -i /home/gportay/output-rpi3-qtwe/images/rpi-firmware/config.txt
sed: -e expression #1, char 8: extra characters after command
+ case "${arg}" in
+ gpu_mem=ome/gportay/output-rpi3-qtwe/images
+ sed -e '/^ome/gportay/output-rpi3-qtwe/images=/s,=.*,=ome/gportay/output-rpi3-qtwe/images,' -i /home/gportay/output-rpi3-qtwe/images/rpi-firmware/config.txt
sed: -e expression #1, char 8: extra characters after command
The issue comes from the use of $1 instead of $arg to extract the gpu_mem
value. $1 is the $(BINARIES_DIR) which leads to a sed expression error.
Also, it adds the error flag to the shell script to prevent from such situation
and terminate the build in error.
Signed-off-by: Gaël PORTAY <gael.portay@savoirfairelinux.com>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump the kernel to version 4.13.5 and U-Boot to 2017.09.
While at it, remove the custom scripts for generating the SD card image
and use the standard scripts instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The "virt" machine supports disk emulation, so use a ext4 rootfs instead of
initramfs for consistency with the other qemu defconfigs.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Mainline kernel is able to decode video via the coda driver.
Add support for it and also add some explanation on how VPU decoding
can be tested with Gstreamer.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Introduce imx6-sabreauto_defconfig that uses mainline U-Boot and
mainline kernel.
As mainline U-Boot supports SPL, it is possible to boot the same
sdcard.img in the three mx6sabreauto variants: imx6q, imx6dl and imx6qp.
Also update the readme.txt file to explain how to build an image for
mx6sabreauto boards using mainline U-Boot and kernel.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[Thomas: regenerate gitlab-ci.yml file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Improve the explanation of the need for using the performance governor.
This problem is specific to mx6sabresd board and the Egalax touchscreen
running a mainline kernel, so make this clear.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The parts of the readme.txt that specify the board-specific aspects
(DTB files, KMS config json file) were a bit confusing. For the DTB
files this is solved by putting the board it applies to after the DTB
file name. For the json files, this is solved by adding an extra line,
so the CinematicExperience-demo is clearly separated from the setting
of QT_QPA_EGLFS_KMS_CONFIG.
Also remove the 'for all boards' line in the beginning, it doesn't add
any value.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This patch add support for Open Frame C.TOUCH 12 Kit.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This patch add support for Open Frame C.TOUCH 10.1 Kit.
Since the defconfig is no longer only for the starter kit, remove that
from BR2_TARGET_GENERIC_ISSUE.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add the new SAMA5D27 SOM1 Evaluation Kit with linux4sam_5.7 components.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The amount of GPU memory can be set using the new option --gpu_mem_XXX
(where XXX is the total amount of memory available on the board).
Signed-off-by: Gaël PORTAY <gael.portay@savoirfairelinux.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add an entry to explain how to run the glmark benchmark.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Bump the kernel version to 4.13.3.
Kernel 4.13.3 uses the /dev/dri/card0 device as rendering node, so
adjust it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
