Up to now, Raspberry Pi Zero W (rpi0w) could be built with the normal
raspberrypi0_defconfig. However, then you don't have support for the
Bluetooth out-of-the-box, which makes using a W a bit pointless.
Therefore, create a separate defconfig for the W. It is a copy of
raspberrypi0_defconfig with the following changes:
- Add DT overlays (from rpi-firmware) to support Bluetooth.
- Pass --add-pi3-miniuart-bt-overlay to post-image.sh.
Since there is now a separate raspberrypi0w_defconfig, the W support
can be removed from raspberrypi0_defconfig.
Signed-off-by: Yves Deweerdt <yves.deweerdt.linux@gmail.com>
[Arnout:
- Bump to same kernel version as raspberrypi0.
- Remove redundant comment.
- Remove redundant default BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS=y.
- Improve commit log.
- Refresh .gitlab-ci.yml.
]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
The uCLS1012A-SOM product family (ucls1012a) is an Arcturus Networks Inc.
64bit ARM Cortex-A53 class System on Module powered by a NXP QorIQ LS1012A
Low Power Communication Processor. This 314 pin MXM3.0/SMARC module card
contains DDR3, QSPI NOR Flash, eMMC NAND Flash, optional Audio CODEC and is
available with 1 or 2 Gig-Ethernet PHYs.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Changes v1 -> v2:
- updated kernel and u-boot source repositories to github
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The T1 QoriQ from NXP has had a few varients of RDB dev boards.
This target is against the latest D4RDB version. Any of the
other versions before D4RDB (plain RDB), may require backing off
the uboot version to SDK 1.6 and/or adjusting the kernel dtb used.
This board configuration provides an upstream kernel build which
has been verified to boot on target.
The target assumes the user still uses the NXP suggested prebuilts
in the SDK2.0 (last release for PowerPC). If a uboot rebuild is
required, the source for SDK2.0 can be found in the following repo.
http://git.freescale.com/git/cgit.cgi/ppc/sdk/u-boot.git/tag/?id=fsl-sdk-v2.0-1703
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Replacing the p1010rdb, this board is based on the tower development
system still available by NXP. The board is setup to track upstream
Linux and has been bumped from 4.1 to 4.15 (compared to p1010).
The target does not build uboot and assumes the user still uses the NXP
suggested prebuilts in the SDK2.0 (last release for PowerPC). If a
uboot is required, the source for SDK2.0 can be found in the following
repo.
http://git.freescale.com/git/cgit.cgi/ppc/sdk/u-boot.git/tag/?id=fsl-sdk-v2.0-1703
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Rename the confusing and misleading ts5x00 directory to a real reference
platform name, ts5500. The readme.txt file already states the support
for both TS-5500 and TS-5400 platforms.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig fails to build with gcc 6.x, even though we switched to
using gcc 6.x as the default gcc version in May 2017.
This defconfig also hasn't seen any non-mechanical update since
November 2015.
So it's time to get rid of it, in order to remove the following build
failure:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306938
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig fails to build with gcc 6.x, even though we switched to
using gcc 6.x as the default gcc version in May 2017.
It hasn't been updated since April 2017, and the original submitter,
Fabio Porcedda said:
Unfortunately a newer kernel doesn't boot and I don't have the time
to fix the issue. If having a defconfig that doesn't build on gcc
6.x is unacceptable feel free to remove it.
So, let's get rid of this defconfig, which will remove the following
build error:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306952
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig currently doesn't build with GCC6 (Linux 4.1).
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306827
A maintainer w/board isn't available to make updates, so removing
this config.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
>From the original submitter of this defconfig:
"""
I no longer have access to ci40 board. It would be difficult for me to
maintain it.
"""
And this defconfig currently fails to build with gcc 6.x. Therefore,
drop it.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306806
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig currently fails to build the Linux kernel:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306826
In addition, the U-Boot build had already been removed in commit
12c01e4a05
("configs/freescale_mpc8315erdb: remove U-Boot build"), back in
October 2016, and nobody bothered fixing it.
This defconfig was originally contributed and maintained by Gustavo
Zacarias, but he is no longer active in Buildroot, and nobody
expressed interest in this defconfig, so let's get rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Currently 'run-tests -l' is broken. It breaks 'make .gitlab-ci.yml' that
in turn breaks the job in GitLab.
TestRustBase is not a test case by itself, so it can't have a method
with the name starting with "test_" otherwise nose2 assumes it is a test
case.
Move the test_run method from the base class to the derived classes.
While at it, update .gitlab-ci.yml with the new test cases.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/52000035
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Cc: Eric Le Bihan <eric.le.bihan.dev@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
[Thomas: really set the transparent compression option, take into
account the renaming of the option.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The defconfig is dumped at the very beginning of the build log, but the
resulting .config is still interesting to get, in case some settings did
not end up in there (e.g. because of the host gcc version, or because of
conflicting settings, or because the Config.in changed without the tests
being updated, or...).
So, add the .config to the list of artefacts to save.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Arnout Vandecappelle <arnout@mind.be>
Acked-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Orangepi PC2
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Zero Plus2
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Prime
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Win/Win Plus
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Olimex A64-OLinuXino
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Tsvetan Usunov <usunov@olimex.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for FriendlyARM Nanopi NEO2 board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Yuefei <yftan@friendlyarm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for FriendlyARM Nanopi A64
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Yuefei <yftan@friendlyarm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for SoPine board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: TL Lim <tllim@pine64.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Pine64 board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: TL Lim <tllim@pine64.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for bananapi M64 board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Jason <manager@sinovoip.com.cn>
Cc: hailymei@banana-pi.com <hailymei@banana-pi.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add MacchiatoBin board by SolidRun. This board is based on Marvell
Armada 8040 SoC. Board support package includes the following
two options: mainline and vendor BSPs.
Mainline BSP:
- Marvell ATF v1.3-armada-17.10
- mainline U-Boot v2017.11
- mainline Linux kernel v4.14.4
Marvell BSP with more hardware support enabled:
- Marvell ATF v1.3-armada-17.10
- Marvell U-Boot based on v2017.03
- Marvell Linux kernel based v4.4.52
More details about this board are available on wiki:
- http://wiki.macchiatobin.net
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
[Thomas: misc tweaks in readme.txt.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Now that all issues in hash files have been fixed, let's try to make
sure we don't introduce new ones by checking regularly the hash files
issues in Gitlab CI.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The addition of a new defconfig in commit
459e3320dc ("configs/imx6sx-sdb: Add new
defconfig") introduced changes in the DEVELOPERS file and
.gitlab-ci.yml file that were not matching the defconfig name. This
commit fixes those issues.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6ulevk_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6sx-sdb_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6slevk_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for bananapi M1 board with below features:
- U-Boot 2017.09
- Linux 4.13.7
- Default packages from buildroot
Cc: Jason <manager@sinovoip.com.cn>
Cc: hailymei@banana-pi.com <hailymei@banana-pi.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Introduce imx6-sabreauto_defconfig that uses mainline U-Boot and
mainline kernel.
As mainline U-Boot supports SPL, it is possible to boot the same
sdcard.img in the three mx6sabreauto variants: imx6q, imx6dl and imx6qp.
Also update the readme.txt file to explain how to build an image for
mx6sabreauto boards using mainline U-Boot and kernel.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[Thomas: regenerate gitlab-ci.yml file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Commit 95cb1465f0 added the
atmel_sama5d27_som1_ek_mmc_dev_defconfig but forgot to update
.gitlab-ci.yml. Update it now.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
After the conversion to SPL the imx6sabresd defconfig targets have
been renamed, so update their entries accordingly.
Suggested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This is similar to the ppc64_pseries config, except we build for little
endian instead of big endian.
The default architecture is set to Power8 as this was the first fully
enabled LE machine.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Commit cef57c9642 added
bananapi_m2_plus_defconfig but forgot to update .gitlab-ci.yml. Do it
now.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
grub is no longer maintained: it is stuck at version 0.97 with huge
patches that have no opportunity to be applied upstream, as upstream
has even renamed it grub-legacy.
Besides, it no longer builds correctly with recent binutils versions,
and even the huge patches we could grab from Debian do not help the
slightest.
Since upstream really considers it dead, and there are at least two
alternatives (grub2 and syslinux), just remove grub.
Add a legacy entry.
Remove the test cases as well.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
The TS-7680 is an i.MX286 ARM ARM926EJ-S board with 10/100 Ethernet,
USB port, eMMC and CAN ports.
The TS-7680 uses a 3.14.28 Linux kernel provided by Technologic Systems:
https://github.com/embeddedarm/linux-3.14.28-imx28
U-Boot is not provided as the manufacturer recommends not to update the
built-in bootloader.
For more informations please see:
https://wiki.embeddedarm.com/wiki/TS-7680
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
[Thomas: use same headers as the kernel being built, update .gitlab-ci.yml.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
i.MX1/L boards require an old Linux kernel version to run, which is not
compatible with latest Buildroot needs.
Will fix:
https://gitlab.com/buildroot.org/buildroot/-/jobs/27873568
Signed-off-by: Julien BOIBESSOT <julien.boibessot@armadeus.com>
[Thomas: update .gitlab-ci.yml file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx7d-pico, which is a board based on NXP
i.MX7D processor.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
[Thomas:
- add upstream references for the Linux kernel patches
- fix typoes in readme.txt
- remove audio-related packages in defconfig
- regenerate .gitlab-ci.yml]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Multiply the timeouts for emulator in the gitlab runners by 10 to avoid
sporadic failures in elastic runners.
Cc: Arnout Vandecappelle <arnout@mind.be>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Introduce imx6q-sabresd_qt5_defconfig that supports the opensource
Etnaviv graphical stack.
This defconfig provides a way to quickly test some graphical applications,
such as kmscube, qt5, glmark2.
Currently kernel mainline exhibits issues when running cpufreq as ondemand
governor on mx6, so add a linux fragment that disables such option for the
time being.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[Arnout:
- Add Fabio to DEVELOPERS
- Rename linux config fragment to linux_qt5.fragment
- Add comment to linux_qt5.fragment why it is needed
- Add explicit CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y to it
- Reorder defconfig entries to they match imx6q-sabresd_defconfig
- Remove strace and host-uboot-tools, neither seems to be needed
- Drop BR2_PACKAGE_QT5BASE_LICENSE_APPROVED, it no longer exists
- Replace BR2_TARGET_ROOTFS_EXT2_BLOCKS with BR2_TARGET_ROOTFS_EXT2_SIZE
- Regenerate .gitlab-ci.yml]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
We add the 3 following combinations:
- basic systemd, read-only, network w/ ifupdown
- basic systemd, read-only, network w/ networkd
- full systemd, read-only, network w/ networkd
The tests just verify what the /sbin/init binary is, and that we were
able to grab an IP address. More tests can be added later, for example
to check each systemd features (journal, tmpfiles...)
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Arnout: regenerate .gitlab-ci.yml]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The "builtin" kernel does not boot a systemd-based system, so
we resort to building the same one as currently used by our
qemu_arm_vexpress_defconfig.
We test the 8 following combinations:
- busybox, read-only, without network
- busybox, read-only, with network
- busybox, read-write, without network
- busybox, read-write, with network
- basic systemd, read-write, network w/ ifupdown
- basic systemd, read-write, network w/ networkd
- full systemd, read-write, network w/ networkd
- no init system, read-only, without network
The tests just verify what the /sbin/init binary is, and that we were
able to grab an IP address. More tests can be added later, for example
to check each systemd features (journal, tmpfiles...)
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Arnout Vandecappelle <arnout@mind.be>
[Arnout: update .gitlab-ci.yml]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Sometimes when a test fails in a gitlab pipeline the reason of the
failure cannot be determined using only the logfile.
Add the modified rootfs as an artifact of the job to improve
troubleshooting. To accomplish this, always use -k option from the test
infra, unconditionally add the resulting images to the artifacts, and
let the runner do the cleanup for us.
These artifacts can also be useful when a test fails locally but pass at
gitlab runners.
When the test does not generate a image, this message is displayed in
the runner log:
WARNING: test-output/*/images/*: no matching files
Cc: Arnout Vandecappelle <arnout@mind.be>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for nanopi-m1-plus board
with below features
- U-Boot 2017.07-rc3
nanopi-m1-plus dts support is present in rc3 version
- Linux 4.11.5
- linux patches to add nanopi-m1-plus dts
- Default packages from buildroot
Signed-off-by: Chakra Divi <chakra@openedev.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add Python3 version of TestPython2 to make sure both versions of
Python get unit-tested.
Modify the code of libc_time_test() to support that change (convert
the code to use Python3-style "print").
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
[Thomas: update .gitlab-ci.yml.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Convert TestPythonBase to a true base class that only provides code
implementing various tests without defining tests themselves in a
"discoverable" form.
To retain correct testing functionality, add TestPython2 derived class
that uses code from TestPythonBase to define actual runnable test.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Tested-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
[Thomas: fix typo in commit log, update .gitlab-ci.yml, both pointed
by Ricardo.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for nanopi-m1 board
with below features
- U-Boot 2017.07-rc1
- Linux 4.11.5
- Default packages from buildroot
Signed-off-by: Chakra Divi <chakra@openedev.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
These tests simply build a system with musl and uclibc toolchains, and
boot them under qemu. It allows to minimally validate that our support
for musl/uclibc external toolchains is working. We already had some
tests covering glibc toolchains, so we can now easily test that all
three C libraries are supported.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
This commit is part of the series, as I've written/used those tests to
validate that things are still working correctly with all of glibc,
uclibc and musl toolchains.
This commit improves our .gitlab-ci.yml logic to execute our runtime
tests located in support/testing/. To do so, this commit:
- Adds more Debian packages to be installed, namely the nose2 and
pexpect packages needed by the runtime testing infrastructure, as
well as the necessary Qemu emulators
- The description of how to run the runtime tests. Each test is
executed as a separate Gitlab CI job, so that the status of each
test is easily visible in the Gitlab CI web interface.
- The Makefile is improved to auto-generate .gitlab-ci.yml from
.gitlab-ci.yml.in, like we're doing for defconfigs. Since the
dependencies of .gitlab-ci.yml are no longer correct, we abandon
them and instead make it a PHONY target.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Arnout: simplify .gitlab-ci.in a little, removing redundant stuff;
make .gitlab-ci.yml a PHONY target]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It seems the ! is removed by the yaml parser, so it needs to be quoted.
While we're at it, add some explanatory comment.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The check-DEVELOPERS test would always fail, because && will return
the exit code of the left-hand side if not 0, so it *always* returns
1.
But in fact, the test can be simplified quite a lot: we can run
getdeveloper directly, without arguments. That should just print
'No action specified', but it will also print any syntax errors it
encountered. So we can just 'grep -v' the expected output away; if
there is anything more, grep will return 0, but if there is nothing
more, it will return 1. So we just need to invert the result.
Incidentally, this also fixes the incorrect remaining reference to
support/scripts.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Chakra Divi <chakra@openedev.com>
[Thomas: remove host-uboot-tools from defconfig, already pulled by
BR2_TARGET_UBOOT_BOOT_SCRIPT, remove trailing whitespace.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This verifies that the DEVELOPERS file doesn't contain errors. It
just runs parse_developers from getdeveloperlib and errors out if
that produces any output.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Engicam Is.IoT MX6UL SOM board
with below features:
- U-Boot 2017.07-rc1
- Linux 4.11.5
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas: add host-dosfstools/host-mtools.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Engicam GEAM6UL SOM board
with below features:
- U-Boot 2017.07-rc1
- Linux 4.11.5
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas: add host-dosfstools and host-mtools.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Engicam i.CoreM6 Quad/Dual/DualLite/Solo RQS
board with below features:
- U-Boot 2017.07-rc1
- Linux 4.11.5
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas: add missing host-dosfstools and host-mtools.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Engicam i.CoreM6 DualLite/Solo board
with below features:
- U-Boot 2017.07-rc1
- Linux 4.11.5
- Default packages from buildroot
U-Boot 2017.07-rc1 has common u-boot defconfig for All i.CoreM6
variant boards, so this patch update the same along with
buildroot defconfig that reflect the common name.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for a13_olinuxino board
with below features
- U-Boot 2017.05
- Linux 4.11.5
- Default packages from buildroot
Signed-off-by: Chakra Divi <chakra@openedev.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas:
- use full name in DEVELOPERS file
- remove parametrization of the post-build.sh script, just hardcode
the boot.cmd file used as input
- add missing dosfstools and mtools host packages in defconfig,
needed because a vfat partition is defined in the genimage.cfg
file
- minor tweaks to readme.txt file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
gx6605s is a nice SOC for dvbs2 DVB product, and C-SKY inside.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
[Thomas: drop post-image script copying the gdbinit file, and suggest
to use gdb -x option instead to point to the gdbinit file in board/.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is needed for defconfigs that use syslinux.
Fixes https://gitlab.com/buildroot.org/buildroot/builds/11701092
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit:
- Adds a development rootfs defconfig for the at91sam9x5ek board for
NAND-based configurations.
- Adds SD-card based configurations for the at91sam9x5ek board, both a
minimal one and development one.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
[Thomas: add at91sam9x5ek_mmc_defconfig to have all four combinations:
NAND minimal, NAND development, SD minimal, SD development.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The board support package includes the following components:
- U-Boot 2016.11
- Linux 4.9.3
- packages:
- alsa-utils for basic audio usage of the on-board headphone jack
and microphone
- iw and wpa_supplicant for managing the wireless interface
Two Linux patches are necessary to enable audio and wifi support. Both
patches are fetched from the Linux next branch and are probably mainlined in
Linux 4.11.
A Linux configuration fragment enables the wireless device driver, which
is not enabled by default in the mainline defconfig of the board.
The wifi chip needs a NVRAM configuration file which is provided in the
rootfs overlay.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
[Thomas: remove e2fsprogs from the target packages, add entry in
DEVELOPERS file, remove C++ support.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The buildroot repository is now mirrored on
https://gitlab.com/buildroot.org/buildroot so we can use Gitlab-CI to
test Buildroot. Gitlab-CI is controlled by a .gitlab-ci.yml file
that exists in the repository.
For now, the only test is building all defconfigs (inspired on
https://travis-ci.org/buildroot/buildroot-defconfig-testing/). Since
all the defconfigs have to be specified in the .gitlab-ci.yml file,
we generate the file based on .gitlab-ci.yml.in. The generated
.gitlab-ci.yml file has to be committed into the repository, though,
otherwise Gitlab-CI doesn't see it. So there is also a test to verify
that .gitlab-ci.yml is up-to-date.
Building all the defconfigs takes a long time. Gitlab-CI will do that
every time it pulls from git.buildroot.org, which is once per hour.
That is way too often. Therefore, the defconfigs are not built on pull,
but only on explicit trigger through the API or when a tag is added.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Thomas:
- fix typo not -> no
- add LC_ALL=C when calling 'ls -1' to get a predictable order of the
defconfigs
- regenerate .gitlab-ci.yml.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
