Commit 27bf08e4ad (configs/avenger96_defconfig: bump ATF version to 2.9
for binutils 2.39+ support) bumped TF-A, but it unfortunately does not boot
and instead dies with a panic:
NOTICE: CPU: STM32MP157AAC Rev.B
NOTICE: Model: Arrow Electronics STM32MP157A Avenger96 board
ERROR: nvmem node board_id not found
INFO: PMIC version = 0x10
ERROR: Product_below_2v5=1:
ERROR: HSLVEN update is destructive,
ERROR: no update as VDD > 2.7V
PANIC at PC : 0x2fff086f
Exception mode=0x00000016 at: 0x2fff086f
Instead use v2.5 to match the other stm32mp1 boards and use the same E=0
-Werror workaround. The avenger95 support is unfortunately broken since
v2.3 with the introduction of authentication support, so add a patch to the
DTS to fix that.
Notice that the authentication support was reworked in v2.7 so it is skipped
for the mp157a variant used on the avenger96, so the patch is not upstreamable.
While we're at it, also drop the debug option for consistency with the other
boards.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
While switching bump Linux version to 6.1.57 and U-Boot version to
2023.10.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
While switching bump Linux version to 6.1.57 and U-Boot version to
2023.10.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Also, since with Linux commit [1] it's been defined the mmc* order
making sd-card number to be 1 instead of 0. This prevent to boot from
mmc0 with Linux version 5.10+ so let's change mmcblk0p4 to mmcblk1p4 in
extlinux.conf in order to boot since we bump to Linux 6.5.7
[1]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=0011c6d182774fc781fb9e115ebe8baa356029ae
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since Qemu 6.0.0, a warning appear in the log if a short-form boolean
option is used. This was fixed by Romain for the main cmdline description
(see 04afe86cd7 ("board/qemu/arm-vexpress-tz: use enable=on")) but was
not updated in the alternate cmdlines for when using a dual console or
a GDB debug setup.
By the way, fix description mentioning qemu-system-arm command line option
-S that is an uppercase S, not a lower case s.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for the LicheePi Nano with mainline components:
- U-Boot 2023.04
- Linux 6.5.9
Board homepage and more usable WiKi:
- https://wiki.sipeed.com/hardware/en/lichee/Nano/Nano.html
- https://linux-sunxi.org/LicheePi_Nano
linux.fragment is required to disable some features in order to keep the
kernel size small, otherwise the board does not boot due to limited
memory. See note in readme.txt.
Signed-off-by: Francois Dugast <francois.dugast.foss@gmail.com>
[yann.morin.1998@free.fr:
- use fixed kernel version
- use manufacturer directory
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Group files for board licheepi_zero under the existing manufacturer
directory, like all the other boards by Sipeed.
Signed-off-by: Francois Dugast <francois.dugast.foss@gmail.com>
[yann.morin.1998@free.fr: use the manufacturer sub-dir]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This fixes a typo by dropping off the spurious x in ensure.
Signed-off-by: Gaël PORTAY <gael.portay@rtone.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
am62x_sk_defconfig should be ti_am62x_sk_defconfig
Signed-off-by: Adam Duskett <adam.duskett@amarulasolutions.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Add defconfig for the Khadas VIM3 board which uses a A311D SoC with a 4x
ARM Cortex-A73 + 2x ARM Cortex-A53 big.LITTLE architecture.
This defconfig includes the Linux mainline kernel version 6.3 as well as
mainline uboot version 2023.04 with an in-tree .dts and uboot-defconfig.
It also includes the host-tool amlogic-boot-fip which is necessary for
signing the bootloader. This host tool is used in the post-image.sh script
in order to generate the signed binary.
This binary is then flashed to the final sdcard.img after it is
generated using genimage. It is done in this way because the bootloader
image needs to be flashed in 2 steps. First the first 444 bytes need to
be flashed to the beginning of the sdcard.img, then we need to skip 68 bytes
in the source and the destination and then write the remaining
bootloader image to the sdcard.img.
Ref: http://docs.khadas.com/products/sbc/vim3/development/create-bootable-tf-card
Signed-off-by: Sebastian Weyer <sebastian.weyer@smile.fr>
[Romain:
add BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_3=y
add BR2_TARGET_UBOOT_NEEDS_OPENSSL=y
add BR2_PACKAGE_HOST_DOSFSTOOLS=y for genimage vfat support
]
Signed-off-by: Romain Naour <romain.naour@smile.fr>
The post-image.sh script is used in several STM32MP157-based board
configs. It had hardcoded device tree file names for the supported
boards which were used for matching the expected TF-A binary name.
Replace this mechanism with a pair of grep and sed that build the TF-A
binary name from the device tree file name. For example, if
BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES contained
DTB_FILE_NAME=stm32mp157c-dk2.dtb, the appropriate TF-A file would be
named tf-a-stm32mp157c-dk2.stm32.
Since the Bash Here Strings are removed with this change, I took the
opportunity to remove the only other non-POSIX command, "local", and
then I was able to change the shebang to plain /bin/sh, with -eu for
simpler error handling.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Update the linux-imx kernel to be aligned with the NXP BSP
LF6.1.22_2.0.0 (same release used in meta-freescale [1]).
Add BR2_TARGET_UBOOT_NEEDS_GNUTLS=y and BR2_TARGET_UBOOT_NEEDS_UTIL_LINUX=y
since they are new dependencies for building mkeficapsule u-boot tool.
The uboot-imx doesn't use the default imx8mp-evk devicetree anymore due
to commit [2]:
"Change to use imx8mp-evk-revb4.dtb and imx8mp-ddr4-evk-revb4.dtb
as default kernel DTB for iMX8MP re-design EVK board. Old EVK
board is EOL, to boot old EVK, user can switch to old DTB manually."
Since the freescale_imx8mpevk_defconfig only install imx8mp-evk.dtb in
the final image, the boot stop with:
Booting from mmc ...
Failed to load 'imx8mp-evk-revb4.dtb'
WARN: Cannot load the DT
Add a u-boot defconfig fragment to revert this change [2] and use the
imx8mp-evk.dtb by default.
Runtime tested on i.MX 8M Plus EVK REV B2.
[1] e6b1b6725c
[2] a60e787a6e
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Orangepi Zero3 board:
- U-Boot 2021.07 fork by Orangepi
- Linux 6.1.31 fork by Orangepi
- Default packages from buildroot
Enable CONFIG_MFD_AC200 as it is used directly by other module,
resulting in build failure when disabled.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Tested-by: Sergey Kuzminov <kuzminov.sergey81@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add support for Bananapi M2 Berry board based on the Allwinner V40/A40i
SoC.
- U-Boot 2023.07
- Linux 6.1.38
Board specifications: https://wiki.banana-pi.org/Banana_Pi_BPI-M2_Berry
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
When testing the virt machine with EDK2, the buildroot 6.1 kernel
will not boot as it has no base ACPI support. Whilst you can run
qemu with the -no-acpi option, it would help if basic ACPI support
was there as otherwise there is no output from the kernel post the
ACPI BIOS initialisation.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Now that we have a template generating an equivalent genimage configuration.
The generated genimage is identical to these +/- file ordering and a
trailing comma / newline that is ignored by genimage, E.G. for rpi3-64:
@@ -8,9 +8,10 @@
"rpi-firmware/cmdline.txt",
"rpi-firmware/config.txt",
"rpi-firmware/fixup.dat",
- "rpi-firmware/start.elf",
"rpi-firmware/overlays",
- "Image"
+ "rpi-firmware/start.elf",
+ "Image",
+
}
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The rpi genimage configurations are all identical, except for the boot
partition files, which include:
- Device tree files (*.dtb)
- rpi-firmware files (rpi-firmware/*)
- Kernel image (Image/zImage)
All of these are quite simple to figure out programmatically based on the
content of BINARIES_DIR, so extend post-image.sh to fall back to generating
a genimage configuration based on genimage.cfg.in if a board specific one
does not exist.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Old links are no longer working, so use new links instead.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Old link is no longer working, so use new link instead.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Backport an upstream patch fixing the build with binutils >= 2.38
for riscv's for Zicsr and Zifencei.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/4987456149
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for PineCube with:
- U-Boot 2022.04
- Linux 5.15.61
PineCube is a low-powered, open source IP camera
with the following specs:
- Allwinner S3 Cortex-A7
- 128 MiB DDR3
- 16 MiB SPI flash
- 5 MPx OV5640 camera
- MicroSD slot
- 10/100M Ethernet with passive PoE
- 802.11 b/g/n WiFi
- Bluetooth 4.1
- USB 2.0
- 26 pins GPIO header
- Microphone
- IR LEDs for night vision
Board homepage: https://www.pine64.org/cube/
Board wiki: https://wiki.pine64.org/wiki/PineCube
Signed-off-by: Jan Havran <havran.jan@email.cz>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump qemu_arm_ebbr_defconfig and qemu_aarch64_ebbr_defconfig in sync:
- Bump Linux to v6.4.3
- Bump U-Boot to 2023.07.02
- Bump TF-A to v2.9
While at it, tune the documentation:
- Increase the amount of memory in the example commands to help run the
largest OS distributions.
- Update the link to the IR Guide to point at the latest version.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adds support for TI's SK-AM62 board by introducing the
am62x_sk_defconfig file and related support files.
More information about the board can be found at:
https://www.ti.com/tool/SK-AM62
Signed-off-by: Xuanhao Shi <x-shi@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adds support for TI's SK-AM64 board by introducing the
ti_am64x_sk_defconfig file and related support files.
More information about the board can be found at:
https://www.ti.com/tool/SK-AM64
Signed-off-by: Xuanhao Shi <x-shi@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Acked-by: Andrew Davis <afd@ti.com>
Tested-by: Bryan Brattlof <bb@ti.com>
Cc: Romain Naour <romain.naour@gmail.com>
Reviewed-by: Francois Perrad <francois.perrad@gadz.org>
Reviewed-by: Julien Olivain <ju.o@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The hss-payload-generator cannot find where u-boot.bin is when looking
for it using the config.yaml. Update syntax issues and working
directories. Fix the post image script to allow an image to get built.
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 2a5d90a595 (configs/rock5b: Add patches to fix gcc12 warnings)
introduced the kernel patches in an incorrect directory.
Fix that by moving them in the proper location.
Reported-by: Kilian Zinnecker <kilian.zinnecker@mail.de>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This patch introduces patches for the custom kernel, as it is
currently used for the Radxa Rock 5B. The patches fix two gcc
compiler warnings, which result in a build error, if the kernel
is used with gcc version 12.
Since also the code of custom board drivers for WiFi support is
affected, and no fixes are provided by the vendor, the custom WiFi
support is disabled.
Signed-off-by: Kilian Zinnecker <kilian.zinnecker@mail.de>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The upstream QEMU 'sifive_u' machine supports running upstream U-Boot
for the SiFive HiFive Unleashed board out of the box.
Add the QEMU instructions for testing in readme.txt.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
As the rootfs size is set to 60M, let's put it right on the 4M offset
in the SD card, so that the generated sdcard.img can be exactly
64M. This will allow sdcard.img to be accepted as an image by Qemu,
which requires power of two sizes for the disk images.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The issue seems to be fixed. I checked qemu and linux git repositories
but can not find any information when this is starting to work.
System gets successfully an IP, no further testing was done.
Tested with Qemu 8.0.3 and Linux 6.1.x.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use full relative pathes for rootfs and kernel, like in other
readme's.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Most of the users use HDMI console on RPi and with increasing popularity
of systemd they face a trouble.
systemd doesn't use /etc/inittab, enable getty@tty1.service instead.
Signed-off-by: Alexey Roslyakov <alexey.roslyakov@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update linux-3.14.config for Galileo to enable Linux kernel root
file system on NFS.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch adds a new defconfig for OrangePI PC2 board.
It was supported before in Buildroot, however due to problems in
building TF-A, it was removed in commit
eeede611f8. This commit re-adds it, in a
state that properly builds.
Signed-off-by: Javad Rahimi <javad321javad@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add defconfig for imxrt1050-evk is a development board from NXP.
The i.MXRTxxxx family spreads from i.MXRT1020 to i.MXRT1170 with the
first one supporting 1 USB OTG & 100M ethernet with a cortex-M7@500Mhz
up to the latter with i.MXRT1170 with cortex-M7@1Ghz and
cortex-M4@400Mhz, 2MB of internal SRAM, 2D GPU, 2x 1Gb and 1x 100Mb
ENET. The i.MXRT family is NXP's answer to STM32F7xx, as it uses only
simple SDRAM, it gives the chance of a 4 or less layer PCBs. Seeing
that these chips are comparable to the STM32F7xxs which have Buildroot
ported to them it seems reasonable to add support for them.
https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/i-mx-rt1050-evaluation-kit:MIMXRT1050-EVK
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Cc: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for the icicle kit, the main development board for
Microchip's PolarFire SoC.
The configuration file is microchip_mpfs_icicle_defconfig. It builds a
bootable kernel image with an embedded root file system. The image
built can be flashed to the board using the eMMC or an SD card.
The yaml configuration file is used by the hss payload generator. It
maps the ELF binaries or binary blobs to the individual application
harts (U54s).
The image generator script sets the partitions of the image.
The kernel fragment file sets additional configurations for the icicle
kit in buildroot that are not in the default configuration.
The image tree souce file creates a FIT image.
The post image script creates the payload using the payload generator
host package and finally, creates the FIT image using the ITS after the
kernel build.
The U-Boot script and additional U-Boot configurations ensure that
U-Boot behaves as expected for the icicle kit and boots the FIT image.
The readme.txt file documents how to build and boot the icicle kit with
this configuration.
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Reviewed-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit duplicates the asus_tinker_rk3288_defconfig changing:
- BR2_LINUX_KERNEL_INTREE_DTS_NAME to rk3288-tinker-s
- BR2_TARGET_UBOOT_BOARD_DEFCONFIG to tinker-s-rk3288
- extlinux.conf devicetree to /boot/rk3288-tinker-s.dtb
- root device format to <major>:<minor> in order to prevent the kernel to mount rootfs
from the wrong device
- Add Flávio Tapajós for configs/asus_tinker-s_rk3288_defconfig and for
configs/asus_tinker-s_rk3288_defconfig and for board/asus/tinker-s
Signed-off-by: Flávio Tapajós <flavio.tapajos@newtesc.com.br>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch bumps the versal_vck190_defconfig to xilinx-v2023.1 which includes
the following updates:
- Linux v6.1.5
- U-Boot v2023.01
- TF-A v2.8 (including mainline patches)
- PLM xilinx_v2023.1
- PSMFW xilinx_v2023.1
- versal-firmware uses new github.com/Xilinx/soc-prebuilt-firmware repo
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch cleans up the shellcheck issues in the versal post scripts.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
