This defconfig currently doesn't build with GCC6 (Linux 4.1).
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306827
A maintainer w/board isn't available to make updates, so removing
this config.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
>From the original submitter of this defconfig:
"""
I no longer have access to ci40 board. It would be difficult for me to
maintain it.
"""
And this defconfig currently fails to build with gcc 6.x. Therefore,
drop it.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306806
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
No other changes necessary, 4.15 builds and boots fine.
Signed-off-by: Alex Suykov <alex.suykov@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to version 2018.01 and kernel to 4.15.7.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig currently fails to build the Linux kernel:
https://gitlab.com/buildroot.org/buildroot/-/jobs/55306826
In addition, the U-Boot build had already been removed in commit
12c01e4a05
("configs/freescale_mpc8315erdb: remove U-Boot build"), back in
October 2016, and nobody bothered fixing it.
This defconfig was originally contributed and maintained by Gustavo
Zacarias, but he is no longer active in Buildroot, and nobody
expressed interest in this defconfig, so let's get rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Closes#10831
Commit a952d24b9 (qemu_x86_64: use kernel 4.15) bumped the kernel version
but didn't update the kernel header series to match, causing build failures.
[Peter: reworded]
Signed-off-by: Ciro Santilli <ciro.santilli@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Orange-Pi Zero Plus2 board has AP6212 WiFi/BT combo, but does
not have ethernet port. So it makes sense to enable wireless
networking by default:
- add DTS patch enabling AP6212 WiFi/BT combo support
-- this patch is on its way to mainline Linux v4.16
- enable WiFi support in kernel config
- enable Broadcom brcmfmac kernel driver in kernel config
- add Broadcom wireless firmware package to image
- add basic wireless tools to image
- add mdev to image to enable module autoloading
- add rootfs overlay with proper NVRAM file for on-board AP6212 chip
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump versions:
- use U-Boot 2008.01
- use Linux kernel v4.15.2
Drop patch with dts sdcard fix since it has been
merged to Linux v4.15.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
For this platform, u-boot uses dtoc during the build, which needs Python
libfdt. Set the corresponding option TARGET_UBOOT_NEEDS_PYLIBFDT in the
defconfig.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add TARGET_UBOOT_NEEDS_PYLIBFDT to all defconfigs, where u-boot needs
Python libfdt to build.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Mike Harmony <mike.harmony@snapav.com>
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Cc: Jan Kraval <jan.kraval@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since kernel 4.15 the wandboard rev D1 variants are supported.
Add support for them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump U-Boot to 2018.01 version and kernel to 4.15.1.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump U-Boot to 2018.01 version and kernel to 4.15.1.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
With this commit we update Linux kernel version to 4.15 and
Linux headers version to 4.15.
Also patches for arc vdk are removed because these
changes were applied in Linux 4.15.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump Linux to 4.15 and U-Boot to 2018.01. Remove networking dts patches
since they has landed in Linux 4.15. Update readme.txt: fix mainline BSP
versions and update boot selection for board rev 1.3.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump Linux to 4.15 and U-Boot to 2018.01. Enable dhcp for eth0 since
Ethernet support for Allwinner H2/H3 SoCs has landed in Linux 4.15.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump Linux to 4.15 and U-Boot to 2018.01. Enable dhcp for eth0 since
Ethernet support for Allwinner H2/H3 SoCs has landed in Linux 4.15.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to 2018.01 and kernel to 4.14.4 version.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to 2018.01 and kernel to 4.14.4 version.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to 2018.01 and kernel to 4.14.4 version.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to 2018.01 and kernel to 4.14.13 version.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump U-Boot to 2017.11 and kernel to 4.14.13 versions.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add a genimage.cfg to create a working sdcard.img for the ci20
hardware. We also need a uboot-env.txt to create the partition for
the uboot environment.
Update the board/ci20/readme.txt with the related information. Remove
the tftp netboot description from the readme as it is already to
complicated for a basic bootable example.
Signed-off-by: Johannes Schmitz <johannes.schmitz1@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Currently in Orange Pi boards post-build script is used only to generate
U-Boot boot script and post-image script is used only to generate sdcard
image according to genimage configuration. However both those tasks can
now be handled by generic Buildroot tools:
- BR2_TARGET_UBOOT_BOOT_SCRIPT config options
- support/scripts/genimage.sh script
This patch drops custom scripts replacing them
by generic Buildroot tools.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also include new boot scripts to match standard distro uboot commands.
Our previous 6x_bootscript and 6x_upgrade used custom variables and
their naming don't make sense now that we target more than i.MX6 CPU.
Therefore those old scripts are marked as legacy and kept for now but
the goal is to deprecate and remove them later.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Currently based upon 4.9.74 stable release.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also switch repository from old freescale site to codeaurora:
https://source.codeaurora.org/external/imx/
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump to U-Boot 2017.11 and kernel to 4.14.11.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump to U-Boot 2017.11 and kernel to 4.14.11.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Orangepi PC2
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Zero Plus2
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Prime
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Win/Win Plus
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Olimex A64-OLinuXino
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Tsvetan Usunov <usunov@olimex.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for FriendlyARM Nanopi NEO2 board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Yuefei <yftan@friendlyarm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for FriendlyARM Nanopi A64
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Yuefei <yftan@friendlyarm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for SoPine board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: TL Lim <tllim@pine64.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Pine64 board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: TL Lim <tllim@pine64.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for bananapi M64 board
with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: Jason <manager@sinovoip.com.cn>
Cc: hailymei@banana-pi.com <hailymei@banana-pi.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add MacchiatoBin board by SolidRun. This board is based on Marvell
Armada 8040 SoC. Board support package includes the following
two options: mainline and vendor BSPs.
Mainline BSP:
- Marvell ATF v1.3-armada-17.10
- mainline U-Boot v2017.11
- mainline Linux kernel v4.14.4
Marvell BSP with more hardware support enabled:
- Marvell ATF v1.3-armada-17.10
- Marvell U-Boot based on v2017.03
- Marvell Linux kernel based v4.4.52
More details about this board are available on wiki:
- http://wiki.macchiatobin.net
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
[Thomas: misc tweaks in readme.txt.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Run-time tested on ZedBoard, build-tested on the other boards]
[Peter: also add host-dosfstools / host-mtools to make vfat images]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
We are about to introduce genimage support for the Zynq boards. For
all of them U-Boot loads the DTB from a file named "devicetree.dtb" so
we need to rename it on the SD card image.
We could use genimage itself to rename files while creating the
image. But this would require a different genimage.cfg for each board,
leading to duplicate code.
Instead let's create a "devicetree.dtb" symlink pointing to the dtb
listed in the configuration. Currently all the Zynq-based boards have
only one DTS configured, but if one had two or more of them, the
symlink would point to the first one.
[Peter: only create symlink if dtb option is available]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
ATF can be used in different ways:
- ATF encapsulates U-Boot as the BL33, which is what is done on ARM
Juno (currently supported in Buildroot) and Marvell platforms (soon
to be supported)
- U-Boot encapsulates ATF's BL31, which is what is done on Allwinner
ARM64 platforms.
Until now we were assumming the former was always the case, but
obviously it isn't. Therefore, this patch adds an option that allows
to explicitly tell ATF that it encapsulates U-Boot as its BL33.
We adapt the only defconfig that uses ATF so that it enables this
option as appropriate.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Currently, our arm-trusted-firmware unconditionally builds a FIP
(Firmware Image Package). While this is often needed on platforms
where ATF encapsulates U-Boot, it is not the case on some other
platforms where it's U-Boot that encapsulates parts of ATF.
In order to prepare the support for the later platforms, we make
building the FIP image optional, and update the only defconfig we have
that uses ARM Trusted Firmware.
Note: we considered adding a "default y" here to preserve backward
compatibility, but there really isn't any default that is sane:
whether a FIP image needs to be built or not is purely platform
specific.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This board is quite similar to orangepi-one board. Instead of ethernet, it
has RTL8189FTV SDIO WiFi chip.
Board support package includes the following components:
- mainline u-boot 2017.09
- mainline kernel 4.13.11
Signed-off-by: Jan Kraval <jan.kraval@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Make WiFi work out of the box on orangepi-pc-plus:
- add rtl8xx firmware
- add rtl8189fs driver
- add mdev for module autoloading
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This board is a variant of orangepi-pc board. It adds 8GB eMMC and Realtek
RTL8189FTV SDIO WiFi chip. This variant has a separate support in U-Boot
and kernel. So it makes sense to create a separate entry
for this board in buildroot.
Board support package includes the following components:
- mainline u-boot 2017.09
- mainline kernel 4.13.11
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
[Thomas: add entry to DEVELOPERS file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump U-Boot to version 2017.11 and kernel to 4.14.3.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Or1k support improved, f.e. musl can be tested inside qemu.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump kernel to version 4.14 and U-Boot to 2017.11.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6ulevk_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As there is now a defconfig inside kernel sources for mxs platforms, use it.
Signed-off-by: Julien BOIBESSOT <julien.boibessot@armadeus.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This updates the LEGO MINDSTORMS EV3 board to Linux kernel 4.14 and
U-Boot 2017.11.
* Kernel patches are dropped because they are in mainline now.
* This caused the kernel image to be >3M so some adjustments to the image
sizes/layout needed to be made in U-Boot.
* Updated U-Boot version bumped since we are touching this config anyway
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6sx-sdb_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx6slevk_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Make WiFi work out of the box on orange-pi-zero:
- add xr819 firmware to image
- add mdev for module autoloading
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump kernel to 4.13.11 and U-Boot to 2017.09.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Update kernel to 4.13 and U-Boot to 2017.09.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This simplifies the pc configs and respective post image scripts to use
the shared genimage script and separate grub config files.
Separate grub files are cleaner to maintain and easier to copy and
modify, for example to support booting the pc defconfigs in qemu.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump the kernel version to 4.13.8.
Tested with qemu 2.9.1 on bios and UEFI virtual machines.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for bananapi M1 board with below features:
- U-Boot 2017.09
- Linux 4.13.7
- Default packages from buildroot
Cc: Jason <manager@sinovoip.com.cn>
Cc: hailymei@banana-pi.com <hailymei@banana-pi.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump the kernel to version 4.13.5 and U-Boot to 2017.09.
While at it, remove the custom scripts for generating the SD card image
and use the standard scripts instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The "virt" machine supports disk emulation, so use a ext4 rootfs instead of
initramfs for consistency with the other qemu defconfigs.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Mainline kernel is able to decode video via the coda driver.
Add support for it and also add some explanation on how VPU decoding
can be tested with Gstreamer.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Introduce imx6-sabreauto_defconfig that uses mainline U-Boot and
mainline kernel.
As mainline U-Boot supports SPL, it is possible to boot the same
sdcard.img in the three mx6sabreauto variants: imx6q, imx6dl and imx6qp.
Also update the readme.txt file to explain how to build an image for
mx6sabreauto boards using mainline U-Boot and kernel.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[Thomas: regenerate gitlab-ci.yml file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
To the latest commits on the odroidc2-3.14.y / odroidc2-v2015.01 branches.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Dagg <daggs@gmx.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch add support for Open Frame C.TOUCH 12 Kit.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This patch add support for Open Frame C.TOUCH 10.1 Kit.
Since the defconfig is no longer only for the starter kit, remove that
from BR2_TARGET_GENERIC_ISSUE.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add the new SAMA5D27 SOM1 Evaluation Kit with linux4sam_5.7 components.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump at91sam9x5ek, atmel_sama5d2_xplained, atmel_sama5d3_xplained and
atmel_sama5d4_xplained all variants to linux4sam_5.7. The 3 foundation
components have their tags changed (AT91Bootstrap, U-Boot, Linux kernel).
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to 2017.09 and kernel to 4.13.3 versions.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump the kernel version to 4.13.3.
Kernel 4.13.3 uses the /dev/dri/card0 device as rendering node, so
adjust it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
U-Boot 2017.09 uses SPL, so bump to this version so that we can
have a single qt5 image that supports the different imx6 sabresd
boards: imx6q, imx6dl and imx6qp.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
The QT5 rootfs requires more space, so adjust it a larger size.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Now that SPL is supported a single image can run on the different
variants of imx6 sabresd boards: imx6q, imx6dl and imx6qp.
So drop the 'quad' prefix from defconfig, directory and readme file
to make it generic.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Bump U-Boot to 2017.09 version and kernel to 4.13.3.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This is similar to the ppc64_pseries config, except we build for little
endian instead of big endian.
The default architecture is set to Power8 as this was the first fully
enabled LE machine.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
U-Boot 2017.07 has switched to SPL boot, which allows the same binary to
boot on imx6dl, imx6q and imx6qp sabresd boards.
Switch to the SPL mechanism.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Peter: board is from Sinovoip, not Lemaker, move board files,
Use kernel headers from kernel, explicitly use 4.13.3,
drop eth0 dhcp config, cleanup post-build args,
disable tar output format, use u-boot custom format,
add host-dosfstools/mtools for genimage, drop unused
host-uboot-tools/genext2fs]
Signed-off-by: Mike Harmony <mike.harmony@snapav.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to 2017.09 version and kernel to 4.13.3.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot to 2017.09 and kernel to 4.12.12 version.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump to 4.13 kernel and remove all the dts patches as they
are part of upstream now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
minnowboard_max-graphical_defconfig has the line "BR_TARGET_GRUB2=y",
but this currently has no effect because BR_TARGET_GRUB2 cannot be
selected without BR2_TOOLCHAIN_BUILDROOT_WCHAR=y, which is not set by
default.
The minnowboard max defconfig was updated to fix this problem, but the
graphical variant was not updated alongside it.
Signed-off-by: Nicholas Sielicki <sielicki@yandex.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The galileo_defconfig has the line "BR_TARGET_GRUB2=y", but this
currently has no effect because BR_TARGET_GRUB2 cannot be selected
without BR2_TOOLCHAIN_BUILDROOT_WCHAR=y, which is not set by default.
Signed-off-by: Nicholas Sielicki <sielicki@yandex.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
