Commit 24dfbe71e (arch/arm: do not distinguish revisions of ARM1136JF-S)
removed the r0 variant of the arm1136jf-s, but didn't update the defconfig -
So it ends up using arm926 instead.
Fix it by selecting the correct symbol instead.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Similar to the issue with the Atmel A5 based boards, the VFP is optional on
A9 - So we need to enable it to be able to use EABIhf.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The recent changes in Config.in.arm regarding the VFP selection broke the
atmel_sama5d* defconfigs. Ensure EABIhf is selected as all the sama5 have a
vfp.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch adds a minimal working configuration for
Acmesystems Arietta g25.
[Peter: fix whitespace, use same-as-kernel for kernel headers version]
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As a followup to http://patchwork.ozlabs.org/patch/548550/ fully convert
the versatile defconfig to create the dtb and update the instructions.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This config has no prospect of going into the future (by using DTS), and
qemu doesn't do a good job at emulating it (networking problems), so
drop it.
All of the ARM SMP testing duties are now in the vexpress defconfig
which is better suited/supported.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Keep arm_nuri on 3.10.x for the usual reasons.
Keep mips & mipsel (32 bits) on 4.3.x because 4.4.x fails to boot
properly (kernel stuck after the CPU cache info).
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.4.1 2.3.0 YES OK
arm_nuri 3.10.96 2.3.0 YES(1) OK most times(2)
arm_versatile 4.4.1 2.3.0 YES OK
arm_vexpress 4.4.1 2.3.0 YES OK
microblazebe 4.4.1 2.3.0 YES OK
microblazeel 4.4.1 2.3.0 YES OK
mips64el_malta 4.4.1 2.3.0 YES OK
mips64_malta 4.4.1 2.3.0 YES OK
mipsel_malta 4.3.5 2.3.0 YES OK (4)
mips_malta 4.3.5 2.3.0 YES OK (4)
ppc_g3beige 4.4.1 2.3.0 YES OK
ppc_mpc8544ds 4.4.1 2.3.0 YES OK
ppc_virtex_ml507 4.4.1 2.3.0 NO OK
ppc64_pseries 4.4.1 2.3.0 YES OK
sh4 4.4.1 2.3.0 YES OK
sh4eb 4.4.1 2.3.0 NO(3) OK
sparc_ss10 4.4.1 2.3.0 YES OK
sparc64_sun4u 4.4.1 2.3.0 YES OK
sparc_sun4u 4.4.1 2.3.0 YES OK
x86 4.4.1 2.3.0 YES OK
x86_64 4.4.1 2.3.0 YES OK
xtensa_lx60 4.4.1 2.3.0 YES OK
(1) - Supposed to work but broken, probably Qemu emulation issue
(2) - In like 1/3 starts it fails to work properly
(3) - Probably an endian issue with 8139 emulation/driver
(4) - Kernel stuck at cpu cache details from 4.4 - 4.4.1
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
For most defconfigs, it was trivial to deduce the kernel version, by
just reading the version string, which could be:
- a standard upstream version string vX.Y.Z
- a non-standard version string, but still containg the standard X.Y.Z
Those for which it was not so trivial were those hosted on git tree.
Since most were already using a custom linux-headers version, it could
be easily deduced from that. It was confirmed by browsing said git trees
and check the version there.
There are a few cases were there was a mismatch:
- microzed: uses a 3.18 kernel, but 3.8 headers; fixed.
- xilinx_zc706: uses a 3.14 kernel, but 3.8 headers; fixed.
- zedboard: uses a 3.18 kernel, but 3.8 headers; fixed.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Now that we can say that the linux headers version should match that of
the kernel to be built, we inverse the logic in our defconfigs, as it is
more sensible that way.
And also because we'll get rid of the former, converse kernel-same-as-headers
option.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Juno ARM Development Platform (ADP) is a software development
platform for ARMv8-A, it includes the Juno Versatile Express board
and an ARMv8-A reference software port available through Linaro.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update to latest boundary-imx_3.14.28_1.0.0_ga commit which brings the
following additions:
- Fix cache functions export when !MULTI_CACHE
https://github.com/Freescale/linux-fslc/commit/6325d57
- Mandatory for Vivante kernel module
- Add TW686x video decoder support
- Fix OV5642 subdev/capture driver conflict
- Add GSLX680 touchscreen support
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
In order to be abble to select BR2_ARM_FPU_VFPV3D16, BR2_ARM_ENABLE_VFP
must be selected first.
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
In order to be abble to select BR2_ARM_FPU_VFPV3D16, BR2_ARM_ENABLE_VFP
must be selected first.
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also updating the documentation with the dd instruction to flash the
bootable media.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Peter: use tarball for Linux kernel, use 4.4 kernel headers]
Signed-off-by: Eelco Chaudron <echaudron@xiot.nl>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
genimage from the post-image script needs mkdosfs to create fat partition:
>>> Executing post-image script board/orangepi/orangepipc/post-image.sh
sh: 1: mkdosfs: not found
vfat(boot.vfat): failed to generate boot.vfat
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As can be seen at
https://travis-ci.org/buildroot/buildroot-defconfig-testing/jobs/99518455,
the new Orange Pi PC defconfig fails to build due to DTC being missing
when building U-Boot. This commit adds the appropriate option to add
DTC as a dependency to U-Boot.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update the raspberrypi and raspberrypi2 configs to use genimage directly
to build the image.
Update the documentation to reflect this, and drop the volatile rootfs
option since it doesn't make much sense and it's not easily integrated
with the genimage configurations.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch updates the Cubieboard2 board defconfig to use newer u-boot
and linux versions, along with a few other improvements.
The other improvements were mostly backported from the recent Orange Pi
defconfig inclusion and are related to image generation.
linux-sunxi.org was used as a reference for both linux and u-boot
defconfig names.
In detail:
- Update linux to vanilla upstream -- currently 4.3.3 is the most
up-to-date. Although it lacks some features present only in the
linux-sunxi 3.4 branch, upstream support appears to be relatively mature
and is already being deployed by default by distributions such as Arch
Linux ARM.
- Update u-boot to vanilla upstream 2015.10. According to
linux-sunxi.org, upstream fully supports major functions (except NAND)
since 2015.07.
- Change image format to zImage and drop custom image generation script
in favour of genimage, as pointed out by reviewers in the Orange Pi
defconfig submission.
This was tested in a Cubieboard2 board with boot from mmc and it boots
fine to login prompt.
This has not been tested in a Cubieboard (A10) as I don't own any; the
version bumps probably apply to it although there are some differences
(lack of VFPv4 support, Cortex-A8 instead of Cortex-A7), so I have kept
the current Cubieboard defconfig and its scripts. This one has been only
build-tested.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit adds a configuration for the Orange Pi PC board,
<http://www.orangepi.org/orangepipc/>.
Signed-off-by: Eelco Chaudron <echaudron@xiot.nl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The arm_foundationv8_defconfig currently doesn't build because it uses
an external AArch64 toolchain that has been updated (Linaro toolchain)
and is now based on gcc 5.x. Unfortunately, Linux 3.13 is too old to
be built with gcc 5.x.
As a minimal fix to make this defconfig build again, we switch to use
the internal toolchain backend. At the time this defconfig was
introduced, there was no support for AArch64 in the internal toolchain
backend, but now that it is available, there is no reason to not use
it. This makes the defconfig also more consistent with the other
defconfigs.
Obviously, the kernel headers used to build the toolchain are set to
the fixed version 3.13, so that they match the kernel being used.
While we're at it, the readme.txt file corresponding to this defconfig
is updated. Runtime testing has been performed with the latest version
of the ARM Foundation model.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Enable dhcp networking for qemu configs considered good enough for
testing purposes.
This excludes:
arm_nuri - emulation doesn't seem 100% correct for networking.
ppc_virtex_ml507 - doesn't emulate networking.
sh4eb - emulation doesn't seem 100% correct for the NIC.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Capitalize comments in a consistent way.
Cleanup redundant entries.
Drop global patch dir for sparc ss10 since it's not required any more.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Board support package includes:
* Toplevel build root configuration
* Github based 3.8.7 Kernel
* Upstream 3.8.7
* Linux 3.8.7 Kernel Driver Patches
* Linux 3.8.7 configuration
* Grub configuration
* Init Script to load modules
* genimage config to create sdcard image.
[Thomas: simplify post-image script since there is now only one call
to genimage.]
Signed-off-by: Ray Kinsella <ray.kinsella@intel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Now that uclibc-ng was bumped to version 1.0.9 nothing prevents x86
from working correctly.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
ppc-mpc8544ds: switch to custom kernel config since the new 4.3-shipped
mpc85xx_basic_defconfig doesn't work with Qemu.
Incidentally while cleaning it up it now seems to work fine with newer
qemu versions.
sparc64_sun4u: ditch ne2k driver since it's useless, and add the e1000
driver which works fine.
x86: stick to 4.2.x kernels since 4.3 doesn't work right with uclibc
(any variant) based toolchains.
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.3 2.3.0 YES OK
arm_nuri 3.10.93 2.3.0 NO(1) OK(2)
arm_versatile 4.3 2.3.0 YES OK
arm_vexpress 4.3 2.3.0 YES OK
microblazebe 4.3 2.3.0 YES OK
microblazeel 4.3 2.3.0 YES OK
mips64el_malta 4.3 2.3.0 YES OK
mips64_malta 4.3 2.3.0 YES OK
mipsel_malta 4.3 2.3.0 YES OK
mips_malta 4.3 2.3.0 YES OK
ppc_g3beige 4.3 2.3.0 YES OK
ppc_mpc8544ds 4.3 2.3.0 YES OK
ppc_virtex_ml507 4.3 2.3.0 NO OK
ppc64_pseries 4.3 2.3.0 YES OK
sh4 4.3 2.3.0 YES OK
sh4eb 4.3 2.3.0 NO(1) OK
sparc_ss10 4.3 2.3.0 YES OK
sparc64_sun4u 4.3 2.3.0 YES OK
sparc_sun4u 4.3 2.3.0 YES OK
x86 4.2.6 2.3.0 YES OK(3)
x86_64 4.3 2.3.0 YES OK
xtensa_lx60 4.3 2.3.0 YES OK
(1) - Supposed to work but broken, probably Qemu emulation issue
(2) - In like 1/3 runs it fails to start properly
(3) - linux 4.3.0 doesn't like uclibc-based toolchains (net issues)
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Remove the integrator926_defconfig configuration, which has not been
updated since a very long time, and targets hardware that is quite
difficult, not to say impossible, to get.
While Qemu has an emulation for the Integrator CP platform, it doesn't
seem to emulate a hard drive, which makes it not very useful. In
addition, we already have the qemu_arm_versatile_defconfig for an
ARMv5 platform emulated in Qemu.
Therefore, let's get rid of this fairly old and never updated
defconfig.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This defconfig has not been updated since a long time, and it now
fails to build because the latest version of U-Boot has removed for
the Snowball because nobody converted it to the new U-Boot
standards. And our defconfig was not specifying an explicit U-Boot
version for it.
On the kernel side, the Git repository has not seen any commits since
3 years, and generally speaking, the Snowball project and the SoC it
is based on are no longer being developed.
Consequently, let's get rid of this defconfig altogether.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The i.MX6 SoloX SABRE board for smart devices is Freescale's reference design
board based on the heterogeneous ARM Cortex-A9 + Cortex-M4 i.MX6 SoloX
applications processor.
This defconfig is inspired from previous freescale_imx6*sabresd_defconfig, and
is based on Freescale "official" git repo on git.freescale.com and SW release
3.10.53_1.1.0_ga.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Gary Bisson <bisson.gary@gmail.com>
Cc: Jérôme Pouiller <jezz@sysmic.org>
Cc: Gilles Talis <gilles.talis@gmail.com>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Virtualizer Development Kit (VDK) Family for ARM Cortex Products
consists of a set of virtual prototypes that provide a virtualizer for
the ARM core variants. The VDK is a standalone package that runs on an
host computer.
[Thomas: drop the following options, which as noted by Arnout, are not
needed:
- BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
- BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="Image"
- BR2_PACKAGE_BUSYBOX_SHOW_OTHERS=y.]
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also revamp the kernel config a bit to make it more featured, enabling
SATA ports and storage.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Use custom version for U-Boot, instead of using the default value as defined
in BR2_TARGET_UBOOT_VERSION.
Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Changes:
* Update Kernel and U-Boot to the latest 2.0.6 BSP release from the
official sources.
* Add genimage config to create bootable SD card image
Signed-off-by: Gergely Imreh <imrehg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As now using zImage/bootz in the 6x_bootscript.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
