U-Boot 2020.10 no longer provides boot command in default environment for
Udoo Quad/Dual board. Boot script needs to be added to the image. In order
to keep using common infrastructure for freescale boards, move boot files
to root filesystem and add boot script there. Also switch Udoo Neo board
to common freescale infrastructure to simplify maintenance.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
After BSP update Udoo Quad/Dual board once again hangs on boot. On a
new kernel disabling CONFIG_USB option is not enough to work around
the troublesome usb host on Udoo Quad/Dual board. So in order to be
future-proof it makes sense to disable usbh1 block in device tree
rather than fine-tune kernel configuration after BSP updates.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit changes the stm32mp1 configurations to use the TF-A ->
U-Boot boot flow (called "trusted boot flow" by ST) instead of the
U-Boot SPL -> U-Boot boot flow. ST recommands this trusted boot, and
it's also the only one that allows to use the STM32 Cube Programmer
for reflashing devices.
As part of this, the genimage configuration file is now generated, as
it contains some file names that depend on the platform. Removing
partition-type from genimage.cfg is mandatory, since it would cause a
hybrid MBR partition table to be created, which itself would prevent
ATF from finding the ssbl parition.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Starting with linux kernel v5.9 all required configuration options are
available in the default config.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since 2020.04 version, the enumeration of MMC has changed, so the boot
script must be updated
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the chromebook elm configuration to use v5.9 instead of an
intermediate release candidate.
At the latter stages of the v5.9 release, a patch was added which
broke the Chromebook Elm HDMI. Therefore add a revert patch to get rid
of this problem. The fix (and the revert) are already on the mailing
list (https://lkml.org/lkml/2020/10/10/32) and should become available
with v5.10
Signed-off-by: Bilal Wasim <bilal.wasim@imgtec.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since 52f188140c (qemu version bump to 5.1),
the image generated by qemu_riscv64_virt_defconfig doesn't boot anyore with
the following error:
rom: requested regions overlap (rom phdr #0: [...]/images//fw_jump.elf. free=0x000000008000e240, addr=0x0000000080000000)
qemu-system-riscv64: rom check and register reset failed
Update the qemu command line as described in the Qemu wiki for riscv64 [1]
Fixes:
https://gitlab.com/jugurthaB/buildroot/-/jobs/686104707
[1] https://wiki.qemu.org/Documentation/Platforms/RISCV#Booting_64-bit_OpenEmbedded_Images
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Jugurtha BELKALEM <jugurtha.belkalem@smile.fr>
Cc: Alistair Francis <alistair.francis@wdc.com>
Cc: Mark Corbin <mark@dibsco.co.uk>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
[yann.morin.1998@free.fr:
- don't force network range
- don't forward TCP port
- drop post-build script to add tty1
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This commit adds supports for building buildroot kernel + rootfs
for MT8173 Elm board, also known as Chromebook Elm
(https://www.acer.com/ac/en/US/content/series/acerchromebookr13).
Though Chrome-OS is officially supproted on this board, the
mainline kernel works as well (benchmarks + conformance), and so
the 5.9 kernel is used. As the 5.9 kernel isn't yet released, we
use the 5.9-rc5 for now, which will be up-revd to 5.9 once its
released.
Using the mainline kernel means that we have to apply certain patches
to get the HDMI screen working. These patches are lying in the
"drm-misc-next" list and will make it to the kernel after 5.9. At that
time, we will remove the patches and point Buildroot to use the latest
kernel (hopefully, 5.10).
This commit also adds an ITS file (for creating FIT images), an ARGS
file (for providing kernel args) and a "sign.sh" script to generate
signed kernel images. Though the "sign.sh" is very similar to the
coresponding file under board/chromebook/snow, it cannot be shared
between both boards, as the script requires access to the board
specific its / args file.
Additionally a readme & defconfig is added to help the user get started.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The same script is going to be used by the Chromebook Elm to generate
a bootable SD / USB image. Therefore, move the script out of the snow
folder to one level above (board/chromebook/snow -> board/chromebook).
Update the chromebook_snow_defconfig to reflect the new location of
the script.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for imx8mqevk_defconfig that allows booting a mainline
kernel.
This defconfig still relies on NXP ATF and U-Boot, but in the long term
the plan is to switch to mainline ATF and U-Boot as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Analog audio is enabled by default in sunxi_defconfig since commit 5d2408c6
(ARM: configs: sunxi: Add sun8i analog codec), so drop from fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Now that upstream supports this board add buildroot support for it,
too.
This supports:
- latest upstream linux kernel. Since the support for this board and
its SoC is still in active development, we want to follow the
upstream kernel releases for now.
- building an image which can be installed to eMMC, SD card or USB
thumb drive.
- upstream u-boot patches are pending, therefore no support for
building a bootloader for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Now that RISC-V 32-bit (RV32) support has been merged into mainline
glibc, we can use the Linux 5.4 kernel.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The apu2 by PC Engines is a 64 bit single board computer with coreboot
BIOS. It only has serial output, but no graphics chip. With its 2–4
ethernet ports, it is often used to build a firewall or router.
The provided defconfig configures busybox and isolinux. It will output
a hybrid ISO image that can be written to a USB stick or burned to a
CD.
Configuration based on a blogpost by Tony Arkles:
http://www.better-bsp.com/blog/2017/03/02/buildrooting-for-apu2/
Signed-off-by: Danilo Bargen <mail@dbrgn.ch>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A defconfig for the friendlyarm nanopc-t4 was added in
c23895f06e, but then removed
in 8efd4463f7 because an ARM32
compiler was needed to build ATF, and this was not supported
back then.
Now, since package/arm-gnu-a-toolchain/ has been added, this
defconfig can be re-introduced.
Following new changes are introduced in comparision with the
older changeset:
- updated readme
- GPT partition layout is being used
- update defconfig to build ATF
- bump u-boot to 2020.07
- bump linux to 5.8.2
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: fixate U-Boot version; remove blind BR2_TARGET_UBOOT_NEEDS_PYTHON]
A defconfig for the friendlyarm nanopi-m4 was added in
493c3979a4, but then removed
in a24bd8936f because an ARM32
compiler was needed to build ATF, and this was not supported
back then.
Now, since package/arm-gnu-a-toolchain/ has been added, this
defconfig can be re-introduced.
Following new changes are introduced in comparision with the
older changeset:
- readme updated
- GPT partition layout
- update defconfig to build ATF
- bump u-boot to 2020.07
- bump linux to 5.8.2
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: fixate U-Boot version; remove blind BR2_TARGET_UBOOT_NEEDS_PYTHON]
A defconfig for the rockpro64 was added in
59e1077b4e, but then removed
in 10f49213b7 because an ARM32
compiler was needed to build ATF, and this was not supported
back then.
Now, since package/arm-gnu-a-toolchain/ has been added, this
defconfig can be re-introduced.
Following new changes are introduced in comparision with the
older changeset:
- renamed defconfig from pine64_rockpro64 to rockpro64
- updated readme
- using a GPT partition layout
- update defconfig to build ATF
- bump u-boot to 2020.07
- bump linux to 5.8.2
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: fixate U-Boot version; remove blind BR2_TARGET_UBOOT_NEEDS_PYTHON]
Mainline Linux now has basic s500/roseapplepi support, so switch to that to
get rid of the dependency on gcc7. Add two patches for the dts / fix that
didn't make it for kernel 5.7.
The mainline kernel does not yet have support for the mmc interface, so
change to initramfs for now. Patches for mmc support have been posted
recently, so this can be reverted once they show up in a stable kernel:
https://lore.kernel.org/lkml/cover.1593124368.git.cristian.ciocaltea@gmail.com/
The owl serial port is called ttyOWLn in mainline, so adjust the bootargs to
match. Also drop the unneeded execute permission on uEnv.txt.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for RK3288 SOM based radxa rockpi-n8
target with below features:
- Custom U-Boot 2020.07-rc4
https://github.com/amarula/u-boot-amarula.git
commit: "ba120841bf40ebaed049d64bb4f980083a1cf6b7"
- Custom Linux 5.7.0-rc1
https://github.com/amarula/linux-amarula.git
commit: "5dcb0132685b07beb82065c5d7521e6c555c55b6"
- GPT partition layout is being used
- Default packages from buildroot
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/674933582
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Signed-off-by: Oleksandr G Zhadan <Oleks@ArcturusNetworks.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The Banana Pi M2 Zero [1] is a board from Sinovoip, based on the
Allwinner H2+ SoC.
It is similar to the other Banana Pi M2* boards, from which this
configuration is inspired.
[1]: http://www.banana-pi.org/m2z.html
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With this patch we enable CONFIG_USB for HSDK, which is not explicitly
selected by UDL since the commit 5d50bd440bc2 ("drm/udl: Make udl
driver depend on CONFIG_USB"). Commit 4c13ca86dcf8 ("ARC:
[plat-hsdk]: fix USB regression") is not yet backported to Linux
kernel 5.6.x, so we enable this option in fragment file for HSDK.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Basic support for the Marvell ESPRESSObin, by Globalscale Technologies.
http://espressobin.net
The kernel config has been extended with a fragment to enable switchcore
support, DSA drivers, and VLAN filtering in the bridge. To make use of
this you need a custom libnl based application, or the iproute2 suite
rather than the brctl tools, which don't support the VLAN filtering.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for imx6ullevk_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add the new SAMA5D27 WLSOM1 Evaluation Kit with linux4sam_6.2
components. Update README file with new defconfigs and new
packages/website.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since commit 'package/rpi-firmware: fix startup file names' ([1]) the
start and fixup file names are normalized to start.elf/fixup.dat,
adjust the rpi4 genimage config files accordingly.
Fixes:
ERROR: file(rpi-firmware/fixup4.dat): stat(.../images/rpi-firmware/fixup4.dat) failed: No such file or directory
ERROR: vfat(boot.vfat): could not setup rpi-firmware/fixup4.dat
[1] https://git.buildroot.net/buildroot/commit/?id=1bdc0334ff6273761b2e7fda730cdcc7e1f46862
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for RK3399 based rockpi-4 targets (model A, B, C)
with below features:
- Custom U-Boot 2020.07-rc4
https://github.com/amarula/u-boot-amarula.git
branch rock-pi
- Linux 5.4.46
- GPT partition layout is being used
- Default packages from buildroot
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for RK3399PRO SOM based rockpi-n10 target
with below features:
- Custom U-Boot 2020.07-rc4
https://github.com/amarula/u-boot-amarula.git
branch rock-pi
- Linux 5.7.2
- GPT partition layout is being used
- Default packages from buildroot
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
virtio-fs allow sharing a directory between the host and the guest.
It require virtiofsd daemon running before starting Qemu.
The wiki [1] recommand to enable the following kernel options:
CONFIG_VIRTIO
CONFIG_VIRTIO_FS
CONFIG_DAX
CONFIG_FS_DAX
CONFIG_DAX_DRIVER
CONFIG_ZONE_DEVICE
But virtio-fs works fine with only VIRTIO_FS.
Note: ZONE_DEVICE can only be enabled on aarch64 since kernel >= 5.7.
ARCH_ENABLE_MEMORY_HOTREMOVE support is missing for previous kernel [2].
[1] https://virtio-fs.gitlab.io/howto-qemu.html
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=bbd6ec605c0fc286c3f8ce60b4ed44635361d58b
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
>From [1]:
This kernel option allow exporting of the QEMU firmware configuration (fw_cfg)
file entries via sysfs. Entries are found under /sys/firmware/fw_cfg when this
option is enabled and loaded.
Enable the suboption to allow the qemu_fw_cfg device to be initialized via the
kernel command line or using a module parameter.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/drivers/firmware/Kconfig?h=v5.4.42#n187
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This driver is intended to be used by mesa virgl Gallium on the guest.
virtio-gpu is enabled by adding "-device virtio-gpu-pci" on the qemu
command line.
It's detected by lspci and dmesg log:
$ lspci
00:01.0 Display controller: Red Hat, Inc. Virtio GPU (rev 01)
$ dmesg
virtio-pci 0000:00:01.0: enabling device (0000 -> 0002)
[drm] pci: virtio-gpu-pci detected at 0000:00:01.0
[drm] virgl 3d acceleration not supported by host
[drm] EDID support available.
[TTM] Zone kernel: Available graphics memory: 51876 KiB
[TTM] Initializing pool allocator
[TTM] Initializing DMA pool allocator
[drm] number of scanouts: 1
[drm] number of cap sets: 0
[drm] Initialized virtio_gpu 0.1.0 0 for virtio2 on minor 0
The framebuffer interface fb0 is now present in /dev
$ ls /dev/fb*
/dev/fb0
See:
https://www.kraxel.org/blog/2019/09/display-devices-in-qemu/https://at.projects.genivi.org/wiki/display/WIK4/GENIVI+Technical+Summit+Session+Content+2018?preview=%2F28412356%2F28412481%2F2018-10-11_GeniviBangalorTechSummit_Virtio_GPU.pdf
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add the CONFIG_PCI symbol due a change in kernel 5.0 [1].
The option was previously enabled by default (default y).
"PCI: consolidate PCI config entry in drivers/pci
There is no good reason to duplicate the PCI menu in every architecture.
Instead provide a selectable HAVE_PCI symbol that indicates availability
of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the
rest in drivers/pci."
Qemu aarch64 provide a PCIe Host bridge but it require CONFIG_PCI_HOST_GENERIC
enabled in the kernel.
With CONFIG_PCI_HOST_GENERIC enabled PCIe host bridge is detected:
$ dmesg
pci-host-generic 4010000000.pcie: host bridge /pcie@10000000 ranges:
pci-host-generic 4010000000.pcie: IO 0x3eff0000..0x3effffff -> 0x00000000
pci-host-generic 4010000000.pcie: MEM 0x10000000..0x3efeffff -> 0x10000000
pci-host-generic 4010000000.pcie: MEM 0x8000000000..0xffffffffff -> 0x8000000000
pci-host-generic 4010000000.pcie: ECAM at [mem 0x4010000000-0x401fffffff] for [bus 00-ff]
pci-host-generic 4010000000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x10000000-0x3efeffff]
pci_bus 0000:00: root bus resource [mem 0x8000000000-0xffffffffff]
pci 0000:00:00.0: [1b36:0008] type 00 class 0x060000
$ lspci
00:00.0 Host bridge: Red Hat, Inc. QEMU PCIe Host bridge
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=eb01d42a77785ff96b6e66a2a2e7027fc6d78e4a
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Qemu for the aarch64 virt emulate an RTC PL031 device.
Enable the kernel support to allow setting the system time.
"date" now return the current time:
Sun Jul 5 20:38:50 UTC 2020
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
And rebase uboot patch.
Tested-by: Maeva Manuel <maeva.manuel@oss.nxp.com>
[Maeva: Tested on i.MX6Quad SabreAuto CPU1]
Signed-off-by: Julien Olivain <julien.olivain@oss.nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This makes the boot script set appropriate root parameters when it's
loaded from a NAND flash device.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The DCON driver for the platform is a staging driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The XO-1 laptop has a NAND flash and firmware capable of reading JFFS2
from it. Enable JFFS2 kernel support so that we'll be able to create
images capable of booting from the internal flash.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A couple of config symbols were mising that things we enable depend on.
Enable them.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This is the keyboard connected via the SP "security processor" on a
XO-1.75. XO-1 has a regular PC keyboard.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
XO-1 has an internal MTD device.
Also, CONFIG_MTD_SPI_NOR was set twice for XO-1.75. One copy is removed,
one remains.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A few conflicts had to be resolved:
- Version number and hash for mesa3d-headers/mesa3d
- Patches added in qemu, and the qemu version number
- The gnuconfig README.buildroot
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch adds support for the i.MX8M Nano EVK Board [1].
The final boot image is created from uboot and firmware binaries in post
image script board/freescale/common/imx/imx8-bootloader-prepare.sh
Note that this config is based on 4.19.35_1.1.0 ; hence, the kernel
configuration needs host-openssl to build.
[1] https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/evaluation-kit-for-the-i-mx-8m-nano-applications-processor:8MNANOD4-EVK
Signed-off-by: Stephane Viau <stephane.viau@oss.nxp.com>
Reviewed-by: Maeva Manuel <maeva.manuel@oss.nxp.com>
Reviewed-by: Julien Olivain <julien.olivain@oss.nxp.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
For some SoCs (i.e.: i.MX8M Nano for now), the DDR training firmware
in the boot image depends on the type of memory installed on a board
(LPDDR4, DDR4, etc...). The previous patch makes this firmware name
agnostic of the DDR type and uses ddr_fw.bin as a generic name. This
patch makes imx8-bootloader-prepare.sh use this generic name,
independently of the kind board DDR type.
Signed-off-by: Stephane Viau <stephane.viau@oss.nxp.com>
Reviewed-by: Maeva Manuel <maeva.manuel@oss.nxp.com>
Reviewed-by: Julien Olivain <julien.olivain@oss.nxp.com>
Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The default iamge size is 32MiB, which is quite low by today's standards.
Besides, the AArch64 kernels are relatively big, which leaves not much
room, if at all, for users to experiment on the default image.
Increase the vfat size to a more reasonable 64MiB.
Note that users who derive an in-tree defconfig for their own case will
allways hit any arbitarary size we put here, so they will anyway have to
also derive this template for their own use-cases.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Commit b80712a16a ("configs/odroidc2:
remove the defconfig") has removed the odroidc2 defconfig, but left
behind a number of files in board/hardkernel/odroidc2, which are now
unused. Let's remove them.
Signed-off-by: Dagg Stompler <daggs@gmx.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This reverts commit f7a887c368 and
23aee3eac4 since the kernel patch
is not needed as soon as qemu >= 3.1.0 is used with a kernel >=
4.11-rc1.
The qemu emulation of sh-sci driver was fixed by adding basic
timeout handling for 9600 bps [1].
[1] https://git.qemu.org/?p=qemu.git;a=commit;h=71bb4ce1b5592cdc03abc48cdf4ecb15b2db81a0
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The Qemu version present in readme.txt files was needed when
the Buildroot's Qemu defconfig was tested manually using the
qemu-system-<arch> binary already present on the host.
This information is now incorrect since we are using host-qemu
package, currently at 4.2.0 version, to do a runtime test since
0c79350638.
For m68k-q800, we can use the upstream qemu since 4.2.0 release
[1].
So, remove this line from the readme.txt.
[1] https://www.qemu.org/2019/12/13/qemu-4-2-0/
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Linux version are changed to the new LTS kernel 5.4.35 for all qemu
defconfigs, except for riscv and csky. Thoses defconfigs are left
unchanged because they require either a custom Linux repository
or a specific kernel header version causing some difficulties when
upgrading to 5.4.35.
Update the nios2-10m50 linux.fragment to update the .dtb build directory
due to a change in kernel 4.20 [1]:
nios2: build .dtb files in dts directory
Align nios2 with other architectures which build the dtb files in the
same directory as the dts files. This is also in line with most other
build targets which are located in the same directory as the source.
This move will help enable the 'dtbs' target which builds all the dtbs
regardless of kernel config.
This transition could break some scripts if they expect dtb files in
the old location.
For x86 and x86_64 kernel, add the CONFIG_PCI symbol due a change in kernel
5.0 [2]. The option was previously enabled by default (default y).
PCI: consolidate PCI config entry in drivers/pci
There is no good reason to duplicate the PCI menu in every architecture.
Instead provide a selectable HAVE_PCI symbol that indicates availability
of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the
rest in drivers/pci.
Update the kernel of ppc-mac99 defconfig added in Buildroot 2019.08.
This version bump was tested on gitlab [4] using the newly introduced
boot-qemu-image.py script [5].
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=118864869805123bf82d666062542440a0fda5dd
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=eb01d42a77785ff96b6e66a2a2e7027fc6d78e4a
[3] a8fac3fcfc
[4] https://gitlab.com/kubu93/buildroot/pipelines/139819874
[5] 0c79350638
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Convert the patch for microblaze kernel added for kernel 3.14 by
Waldemar to git format.
Note: the Waldemar Sob line is missing in the original patch:
fa27985483
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch add support for the low cost QMTECH XC7Z010 starter kit
board [1].
[1] http://www.chinaqmtech.com/xilinx_zynq_soc
Signed-off-by: Martin Chabot <martin.chabot@gmail.com>
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This adds some instructions on how to build and run images for the OLPC
XO laptops.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A defconfig for the nanopi_neo4 was added in
d1cd9cdf26, but then removed in
8af7b11bd8 because an ARM32 compiler was
needed to build ATF, and this was not supported back then.
Thanks to the addition of package/arm-gnu-a-toolchain/, we can now
re-introduce this defconfig.
Compared to the previous defconfig, the following changes were done:
- enable BR2_TARGET_ARM_TRUSTED_FIRMWARE_NEEDS_ARM32_TOOLCHAIN
- bump kernel to 5.4
- increase default rootfs size to 70M
- use mainline u-boot
- switch to Marek Belisko as maintainer
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
NXP i.MX8MNano based SBC with 1GB of LPDDR4 and 16GB eMMC.
More details on the platform here:
https://boundarydevices.com/product/nitrogen8m-nano/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently the volume-label for the vfat partition is a string with
the following pattern: 5934-861D.
Specify the volume-label as "boot" to make it easier to identify it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This defconfig supports the OLPC XO-1 platform.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
There are muliple generations of OLPC laptops, x86 ones based on
Geode, VIA and ARM based with Marvell Armada. All of boot with
OpenFirmware and share some peripherals.
This patch adds the common files.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The support for MacchiatoBin board in U-Boot and Linux has been
significantly improved in the past years. So it no longer makes much
sense to have a separate build configuration based on older vendor
Linux kernel and U-Boot. This commit drops the configuration based on
vendor kernel and U-Boot and renames the mainline-based defconfig.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently the volume-label for the vfat partition is a string with
the following pattern: 5934-861D.
Specify the volume-label as "boot" to make it easier to identify it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Nanopi R1 board with below features:
- U-Boot 2019.01
- Linux 5.0
- Default packages from buildroot
Configuration files taken from Armbian:
https://github.com/armbian/build/blob/master/patch
Signed-off-by: Davide Viti <zinosat@gmail.com>
[Thomas: move U-Boot config and DT to board/friendlyarm/nanopi-r1/uboot/]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit add a post-image script to be used by each qemu board
defconfig in order to generate start-qemu.sh in BINARIES_DIR. The
start-qemu.sh script can be used by Buildroot user to start Qemu
or by a gitlab CI.
To find the correct qemu command line, we use the second post script
argument which must contain "$(BR2_DEFCONFIG)"
BR2_ROOTFS_POST_SCRIPT_ARGS="$(BR2_DEFCONFIG)"
The post-image script expect something like
"/path/to/qemu_aarch64_virt_defconfig" in BR2_DEFCONFIG.
Doing a basename allow to retrieve the name of the defconfig file that
should match on on the "tag" previously introduced in readme.txt files.
For running in the CI, as well as running from a remote machine (e.g. on
a remote build machine), it is better not to start in graphical mode,
but only with the serial line attached to the terminal. The post-build
script prepares two sets of arguments for each case, graphical or
serial, and stores them in the start-qemu.sh script, which then decodes
which to use, based on an argument on the command line (default is still
graphical)
sh4/sh4eb needs a special handling by adding "-serial stdio -display
none"; others only require "-nographics". Some qemu command lines
already contain "-serial stdio", but that does not play nicely with
"-nographics", we remove that when going serial-only (although this
might seem counter-intuitive).
Finally, we ensure the script uses our qemu-system (if it was built).
Signed-off-by: Romain Naour <romain.naour@smile.fr>
[yann.morin.1998@free.fr:
- drop the knowledge about gitlab-ci, replace with an argument to
pass to start-qemu.sh
- adapt the commit log accordingly
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This commit add the name of the Qemu defconfig file after each
qemu command line in order to retrieve it easily.
Since a readme.txt can be shared between several Qemu defconfig, we
need at least one qemu command line in readme.txt for each defconfig.
For now, ignore the qemu_arm_vexpress_tz_defconfig since it fail to build
due to python script issue [1]. Anyway the arm vexpress boot is tested
with qemu_arm_vexpress_defconfig.
[1] http://lists.busybox.net/pipermail/buildroot/2020-February/273738.html
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
There is no reason to create boot.scr in board/udoo/neo and later
install it in TARGET_DIR/boot, leaving a stale file behind.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
There is no reason to create boot.scr in board/solidrun/mx6cubox and
later install it in TARGET_DIR/boot, leaving a stale file behind.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
There is no reason to create boot.scr at board/wandboard and later
install it at TARGET_DIR/boot, leaving a stale file behind.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The U-boot patch has been upstreamed.
Bump U-boot version and drop the patch.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The WDT workaround patch has been upstreamed.
Bump to the new ATF version and drop the patch.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
NXP i.MX8MMini based SBC with 2GB of LPDDR4 and 8GB eMMC.
More details on the platform here:
https://boundarydevices.com/product/nitrogen8m-mini
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- update outdated website URL
- add missing Nitrogen8M configuration
- reword procedure to make it clear it works for all storages
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- To avoid code duplication and to benefit from support script
improvements like empty target dir.
- Note that currently genimage.sh can't be set in defconfig directly for
i.MX8 targets as the POST_SCRIPT_ARGS is used by
imx8-bootloader-prepare.sh
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This initial support includes:
Linux 5.4
U-Boot 2020.01
Arm Trusted Firmware v2.2
Buildroot default packages.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Add support for 8MMini and 8MNano
- Upgrade script now resets by default
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Let's clean up "boards/stmicroelectronics" directory a bit
to have everything in particular directories.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The board support package includes the following components:
- U-Boot 2020.01
- Linux 5.4.26
- Buildroot default packages
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
It will be useful for the upcoming introducing stm32mp157a dk2 board.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Let genimage to match the size of the rootfs image instead.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Instead use generic genimage.sh script.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Commit 3f8ace0028
("board/freescale/common/imx: add support for i.MX8") had its
conflicts incorrectly tweaked when applied to Buildroot. The
ahab-container.img is installed with this name (ahab-container.img) by
the imx-firmware package, and not mx8qm-ahab-container.img or
mx8qx-ahab-container.img.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Julien Olivain <juju@cotds.org>
Tested-by: Julien Olivain <juju@cotds.org>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The current Buildroot defconfigs for qemu_x86 and qemu_x86_64
instantiate a console on tty1, which appears on QEMU's
graphical window. Add a console on the serial port (ttyS0) to
be used later for gitlab testing.
This change is need since the script used for gitlab testing
needs to use a serial output with pexpect.
This change is similar to the one made for raspberrypi [1] to
handle HDMI and serial console:
This requires three changes:
1. have two 'console=' entries in the kernel command line: tty1,
then ttyS0;
2. change BR2_TARGET_GENERIC_GETTY_PORT to "console", so it starts
a getty on the last console= passed to the kernel, ttyS0;
3. add a new getty on tty1 to the generated inittab.
Step 2 is actually obtained by removing BR2_TARGET_GENERIC_GETTY_PORT
entirely from the defconfigs, since "console" is the default value.
Step 3 requires a post-build script since the Buildroot makefiles can
configure only one console.
Note: instead of simply adding a new getty on ttyS0 (which would
work) this patch actually changes BR2_TARGET_GENERIC_GETTY_PORT to
instantiate a console on UART, then adds back tty1 via
post-build.sh. This is done only to avoid the "GENERIC_SERIAL" comment
where we instantiate a console on QEMU graphical window, then
instantiate a really-serial console on another line.
The result is these two inittab lines:
console::respawn:/sbin/getty -L console 0 vt100 # GENERIC_SERIAL
tty1::respawn:/sbin/getty -L tty1 0 vt100 # QEMU graphical window
[1] 20878a1017
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As recently reported to the list:
http://lists.busybox.net/pipermail/buildroot/2020-January/271937.html
The hardcoded rootfs partition size can lead to hard to understand build
failures if more packages are added.
So drop the hardcoded partition size. Genimage will then size the partition
to match the size of the rootfs image (which by default is also 60MB for ext4).
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Now that the metadata_csum ext4 option is disabled, we no longer need
the U-Boot workaround.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Use a post-build script to copy uEnv.txt to BINARIES_DIR, as made for
beaglebone.
Drop the post-image script.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Use the same kernel repository and version as configs/beaglebone
- Rename kernel fragment file
- Update U-Boot to 2019.07
- Select weston and qt5wayland
- Select host-uboot-tools with FIT support, required to create the
images.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The correct syntax that Qt5 understands for display names is
"LVDS1", so fix it accordingly.
Reported-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
In board/freescale/common/imx/imx8-bootloader-prepare.sh, when
invoking mkimage_fit_atf.sh, the U-Boot DTB is passed as parameter, to
be included in the FIT image. This parameter usually comes from
BR2_ROOTFS_POST_SCRIPT_ARGS config option. The variable
BL33=u-boot.bin set in the invocation uses the u-boot image which is
including its embedded DTB. This means the U-Boot DTB is included
twice.
The upstream script mkimage_fit_atf.sh plus its Buildroot patch are
meant to use by default the nodtb variant and use the DTB in a
separate image. See [1] and [2].
The U-Boot default DTB which will be included in u-boot.bin image is
selected with U-Boot CONFIG_DEFAULT_DEVICE_TREE, or DEVICE_TREE
variable when invoking "make". If one of those option is not aligned
to the BR2_ROOTFS_POST_SCRIPT_ARGS config option, it's possible the
two included U-Boot DTBs are different. If such case happens, the
built-in DTB is always used, regardless of the other one, selected
with BR2_ROOTFS_POST_SCRIPT_ARGS.
For example, this case happens for TechNexion Pico Pi i.MX8M and
i.MX8MMini. Since the U-Boot defconfig assumes the nodtb version will
be used, it does not set the default DTB. The u-boot.bin will include
the fsl-imx8mm-evk instead. Including the wrong board DTB breaks the
USB and UMS commands (and possibly others). Since those boards does
not have SD card slots, a recovery serial download is needed at every
update.
This patch make sure that only the separate U-Boot DTB will be
included in the FIT image by using the nodtb variant.
[1] https://source.codeaurora.org/external/imx/imx-mkimage/tree/iMX8M/mkimage_fit_atf.sh?h=rel_imx_4.14.98_2.0.0_ga#n35
[2] https://git.busybox.net/buildroot/tree/package/imx-mkimage/0001-add-support-for-overriding-bl32-and-bl33-not-only-bl.patch?h=2019.11#n42
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since kernel commit a5a56f07c272 ("ARM: imx_v6_v7_defconfig: Select the
coda driver as module") the VPU coda driver is selected as module, so it can
be safely removed from linux_qt5.fragment.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The correct syntax that Qt5 understands for display names is
"HDMI1" and "LVDS1", so fix it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 3468ef16fa
("configs/pc_x86_64_efi: use genimage GPT partition table support")
had a small typo on the path to grub boot.img file: i387-pc instead of
i386-pc, which causes a build failure.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/378314412
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Alexandre PAYEN <alexandre.payen@smile.fr>
Cc: Carlos Santos <casantos@datacom.com.br>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This remove the file boot.cmd to use an extlinux.conf instead.
Signed-off-by: Louis Aussedat <aussedat.louis@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This configuration builds a 64bit image for RaspberryPi 4.
Signed-off-by: Arthur Courtel <arthur.courtel@smile.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The pi3-minuart-bt Device Tree overlay has been renamed to
miniuart-bt, as it is useful/usable for other platforms than the
RPi3. So we use this DT overlay and rename the
--add-pi3-miniuart-bt-overlay option to --add-miniuart-bt-overlay
accordingly.
Signed-off-by: Arthur Courtel <arthur.courtel@smile.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Instead use the generic infrastructure for u-boot scripts and genimage.
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As already done in post-build.sh, to prevent hiding errors.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Let genimage determine rootfs partition size based on the filesystem
image size.
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 68b5b79b2f has set the getty port to the default console but left
"ttyO0" in bootargs, in the U-Boot environment. Use "ttyS0", instead.
Also set loadaddr to 0x82000000 and fdtaddr to 0x88000000, replacing the
values that were valid for the ancient U-Boot and Linux pre-installed on
old boards but cause boot hangs with the current versions.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Thanks to the introduction of GPT partition table support in genimage,
this commit improves the pc_x86_64_efi_defconfig to remove the use of
the custom script creating the image.
Tested in QEMU, not on a physical device.
So:
- revert commit fee29b05bb7db25e37c8a5175ce00dc712554edf[1]
- add GPT support
- tweak shell script to add the correct UUID in genimage config.
[1]: https://git.buildroot.net/buildroot/commit/?id=fee29b05bb7db25e37c8a5175ce00dc712554edf
[2]: https://git.buildroot.net/buildroot/commit/?id=79b8540d624ac4846ba341b1b9691eccacf0bc05
Signed-off-by: Alexandre PAYEN <alexandre.payen@smile.fr>
Cc: Carlos Santos <casantos@datacom.com.br>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[Thomas:
- drop commented code in post-build.sh
- take into account comments made by Carlos Santos in
http://patchwork.ozlabs.org/patch/1143502/]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use the pi3-miniuart-bt device tree overlay (as the 32bit raspberrypi3
defconfig) instead of the enable_uart option.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes reference path "../build/optee_os-" to "./output/build/optee-os-"
as package is optee-os and symbol file here is reached from BR top
dir and assuming output in output/.
Updates GDB tool name to arm-linux-gdb.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This change introduces a Qemu board for an Armv7-A target executing
with OP-TEE secure world services. The target Linux based normal world
embeds the standard minimal filesystem with OP-TEE non-secure components
embedded files from OP-TEE test, examples and benchmark packages.
qemu_arm_vexpress_tz_defconfig differs from qemu_arm_vexpress_defconfig.
Supporting both secure and non-secure worlds on the Arm target mandates
a secure world, here OP-TEE OS, and a bootloader to boot both worlds,
here TF-A (boot/arm-trusted-firmware). Here non-secure Linux kernel is
booted through U-boot
TF-A bootloader (BL1/BL2) => OP-TEE (BL32) => U-boot (BL33).
| Executes as secure | Secure | Execs as Non-secure
| Loads BL32/BL33 in RAM | Jumps to BL33 | Always booted after
| Jumps to BL32 once done | as Non-secure | secure world inits
Vexpress and vexpress-tz defconfigs also differs in that Qemu emulates
a Cortex-A9 in the former and a Cortex-A15 in the later. Cortex-A15
is the Armv7-A CPU used in upstream TF-A and OP-TEE OS packages hence
selected here.
Defconfig adds a fragment to the Linux kernel native configuration to
enable OP-TEE driver support.
Defconfig adds a fragment to the U-Boot native configuration set boot
command, enable semihosting and remove U-Boot persistent environment
storage support.
The defconfig also enables build of the Qemu emulator in case the
system installed Qemu does not yet support CPU TrustZone secure state.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
[Arnout, with the help of Peter: correct spelling mistakes in readme,
fix U-Boot version to 2019.01, download tarball of TF-A instead of git]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
That is useful and needed for upcoming introducing stm32mp157a-dk1 board.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
genimage makes a full copy of the given rootpath to ${GENIMAGE_TMP}/root
so passing TARGET_DIR would be a waste of time and disk space. We don't
rely on genimage to build the rootfs image, just to insert a pre-built
one in the disk image.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Use a post-build script to copy uEnv.txt to BINARIES_DIR, as made for
beagleboneai.
Keep the post-image script because it is still used by beaglebone_qt5.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use support/scripts/genimage.sh, instead, which prevents duplicating
TARGET_DIR under ${BUILD_DIR}/genimage.tmp/root.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Change partition name according to the U-Boot requirements.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
QT_QPA_EGLFS_ALWAYS_SET_MODE=1 needs to be exported, otherwise the Qt5
Cinematic demo throws a storm of the following messages:
Could not queue DRM page flip on screen LVDS1 (Invalid argument)
Improve the instructions by mentioning such requirement.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 5facee5cc3 ("configs/solidrun_clearfog_gt_8k: bump versions of
BSP components") broke automatic load of the mv88e6xxx dsa driver. The
kernel configuration makes the driver a module, which is not loaded
automatically at boot. Mark mv88e6xxx dependencies built-it to fix that.
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add basic support for the Libre Computer "La Frite" SBC.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since the bump to the 20190819 snapshot there is now a dedicated dts file
for the rpi0, so use that rather than the rpi-b-plus one:
bd1336d8b6
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes#12816
Commit 42d22f3bdb ({configs/raspberrypi,package/rpi-firmware}: bump
kernel/firmware to 20190819 version) updated the kernel version but failed
to take into consideration that the rpi0w dts file has been renamed:
6f91b5dbfd
Fix it by renaming the dts/dtb file referenced from the kernel build and
genimage.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This defconfig tries to build an ARM Trusted Firmware version that
needs an ARM32 toolchain, which is not available as the platform is an
ARM64 one. The correct solution for this is to have a package in
Buildroot for an ARM32 bare-metal toolchain, but this wasn't done in
time for the 2019.08 release.
In order to not release 2019.08 with a broken defconfig, let's remove
it. It can be re-added later once the ARM32 bare-metal toolchain
problem has been resolved.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/278489410
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
