234d81bf33
Signed-off-by: Joao Pinto <jpinto@synopsys.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
120 lines
3.4 KiB
Plaintext
120 lines
3.4 KiB
Plaintext
ARM Juno r1/r0
|
|
|
|
Intro
|
|
=====
|
|
|
|
These instructions apply to all models of the ARM Juno:
|
|
- Juno r0 (does not support PCIe)
|
|
- Juno r1 (supports PCIe)
|
|
- Juno r2 (Big Cluster with A72)
|
|
|
|
Buildroot will generate the kernel image, device tree blob and a
|
|
minimal root filesystem.
|
|
|
|
How to build it
|
|
===============
|
|
|
|
Configure Buildroot
|
|
-------------------
|
|
|
|
Configuring Buildroot is pretty simple, just execute:
|
|
|
|
$ make arm_juno_defconfig
|
|
|
|
Build the rootfs, kernel and DTB
|
|
--------------------------------
|
|
|
|
Note: you will need to have access to the network, since Buildroot will
|
|
download the packages' sources.
|
|
|
|
You may now build your rootfs with:
|
|
|
|
$ make
|
|
|
|
(This may take a while)
|
|
|
|
Result of the build
|
|
-------------------
|
|
|
|
After building, you should obtain this tree:
|
|
|
|
output/images/
|
|
+-- rootfs.tar
|
|
+-- juno.dtb (if Juno r0 is used)
|
|
+-- juno-r1.dtb (if Juno r1 is used)
|
|
+-- juno-r2.dtb (if Juno r2 is used)
|
|
+-- Image
|
|
|
|
Preparing your rootfs
|
|
======================
|
|
|
|
Format your pen drive as a ext3 filesystem by executing:
|
|
|
|
$ mkfs.ext3 /dev/<your device>
|
|
|
|
Installing your rootfs
|
|
======================
|
|
|
|
After mounting the pen drive please execute the following:
|
|
|
|
$ sudo tar -xvf output/images/rootfs.tar -C <pen drive mount path>
|
|
|
|
When completed make sure to unmount the device:
|
|
|
|
$ umount <pen drive mount path>
|
|
|
|
Insert the pen drive in one of the ARM Juno' USB type A connectors.
|
|
|
|
Configure *.dtb in the boot configuration for Juno r0
|
|
=====================================================
|
|
|
|
SITE1/HBI0262B/images.txt
|
|
.....
|
|
NOR3UPDATE: AUTO ;Image Update:NONE/AUTO/FORCE
|
|
NOR3ADDRESS: 0x00C00000 ;Image Flash Address
|
|
NOR3FILE: \SOFTWARE\juno.dtb ;Image File Name
|
|
NOR3NAME: board.dtb ;Specify Image name to preserve file extension
|
|
NOR3LOAD: 00000000 ;Image Load Address
|
|
NOR3ENTRY: 00000000 ;Image Entry Point
|
|
......
|
|
|
|
Configure *.dtb in the boot configuration for Juno r1
|
|
=====================================================
|
|
|
|
SITE1/HBI0262C/images.txt
|
|
......
|
|
NOR3UPDATE: AUTO ;Image Update:NONE/AUTO/FORCE
|
|
NOR3ADDRESS: 0x00C00000 ;Image Flash Address
|
|
NOR3FILE: \SOFTWARE\juno-r1.dtb ;Image File Name
|
|
NOR3NAME: board.dtb ;Specify target filename to preserve file extension
|
|
NOR3LOAD: 00000000 ;Image Load Address
|
|
NOR3ENTRY: 00000000 ;Image Entry Point
|
|
......
|
|
|
|
Configure *.dtb in the boot configuration for Juno r2
|
|
=====================================================
|
|
|
|
SITE1/HBI0262D/images.txt
|
|
......
|
|
NOR3UPDATE: AUTO ;Image Update:NONE/AUTO/FORCE
|
|
NOR3ADDRESS: 0x02000000 ;Image Flash Address
|
|
NOR3FILE: \SOFTWARE\juno-r2.dtb ;Image File Name
|
|
NOR3NAME: board.dtb ;Specify target filename to preserve file extension
|
|
NOR3LOAD: 00000000 ;Image Load Address
|
|
NOR3ENTRY: 00000000 ;Image Entry Point
|
|
......
|
|
|
|
Installing kernel image and DTB
|
|
===============================
|
|
|
|
1. Connect to the ARM Juno UART0 and execute USB_ON in the terminal
|
|
2. Connect a USB cable between your PC and ARM Juno USB type B connector
|
|
A mass storage device should appear in your desktop.
|
|
3. Open the software/ folder
|
|
4. Copy the 'Image' file to software/
|
|
5. Copy the 'juno-r1.dtb' (r1), 'juno.dtb' (r0) or juno-r2.dtb (r2) file to software/
|
|
6. Press the red button in the front pannel of ARM Juno
|
|
|
|
At this time, the board will erase the Flash entry for each new item and
|
|
replace it with the lastest ones.
|