1c714bf757
Basic support for the Marvell ESPRESSObin, by Globalscale Technologies. http://espressobin.net The kernel config has been extended with a fragment to enable switchcore support, DSA drivers, and VLAN filtering in the bridge. To make use of this you need a custom libnl based application, or the iproute2 suite rather than the brctl tools, which don't support the VLAN filtering. Signed-off-by: Joachim Nilsson <troglobit@gmail.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
91 lines
3.1 KiB
Plaintext
91 lines
3.1 KiB
Plaintext
Marvell ESPRESSObin
|
|
===================
|
|
|
|
This default configuration allows you to quickly get up and running with
|
|
the Marvell ESPRESSObin board by Globalscale Technologies Inc.
|
|
|
|
The ESPRESSObin is based on the Marvell Armada 88F3720 SoC, coupled with
|
|
a Marvell 88E6341 switch core "Topaz", with three exposed gigabit ports.
|
|
|
|
_________________________
|
|
|# U W L L U #|
|
|
|# S A A A S #|
|
|
|# B N N N B #|
|
|
|# 0 1 #|
|
|
|# Mini #|
|
|
|# -PCI #|
|
|
|# #|
|
|
|# 5 #|
|
|
|#__V___usb_PWR_SATA__SW_#|
|
|
|
|
Fig 1: Overview of board
|
|
|
|
Notice difference in Ethernet port layout compared to the Globalscale
|
|
docs. They order the ports; LAN2, LAN1, WAN (left to right in figure
|
|
above). For more information, see http://espressobin.net
|
|
|
|
|
|
Building
|
|
--------
|
|
|
|
$ make globalscale_espressobin_defconfig
|
|
$ make
|
|
|
|
This generates the kernel image, the devicetree binary, the rootfs as a
|
|
tar.gz, and a filesystem image containing everything.
|
|
|
|
All build artifacts are located in `output/images/`
|
|
|
|
|
|
Booting
|
|
-------
|
|
|
|
To boot, you need a UART connection, using the on-board micro USB port
|
|
set to 115200 8N1.
|
|
|
|
By default, the ESPRESSObin comes with a pre-flashed U-Boot set up to
|
|
load the kernel, device-tree and rootfs from SPI NOR flash. The board
|
|
jumpers can be changed to boot from different sources, see the quick
|
|
start guide for each board revision for details:
|
|
|
|
- ftp://downloads.globalscaletechnologies.com/Downloads/Espressobin/ESPRESSObin%20V5/
|
|
- ftp://downloads.globalscaletechnologies.com/Downloads/Espressobin/ESPRESSObin%20V7/
|
|
|
|
Note: the v5, and earlier, cannot boot from sdcard, so you have to set
|
|
up the factory U-Boot to boot into Buildroot:
|
|
|
|
1. Flash rootfs image to sdcard drive, your `of=` device may differ:
|
|
|
|
$ sudo dd if=output/images/sdcard.img of=/dev/mmcblk0 bs=1M
|
|
$ sync
|
|
|
|
2. Boot board from SPI NOR, interrupt boot by pressing any key ...
|
|
3. Check with `printenv` that the default setup is OK, otherwise ensure
|
|
the following are set, and define `bootcmd` for automatic boot:
|
|
|
|
> setenv kernel_addr 0x5000000
|
|
> setenv fdt_addr 0x1800000
|
|
> setenv fdt_name boot/armada-3720-espressobin.dtb
|
|
> setenv console console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000
|
|
> setenv bootcmd 'mmc dev 0; ext4load mmc 0:1 $kernel_addr $image_name;ext4load mmc 0:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk0p1 rw rootwait; booti $kernel_addr - $fdt_addr'
|
|
|
|
4. Call the boot command, or `reset` the board to start:
|
|
|
|
> run bootcmd
|
|
|
|
|
|
Networking
|
|
----------
|
|
|
|
To enable Ethernet networking, load the `mv88e6xxx` kernel module, and
|
|
bring up each respective interface needed:
|
|
|
|
# modprobe mv88e6xxx
|
|
# ifconfig wan up
|
|
|
|
A more advanced scenario is setting up switching between the ports using
|
|
the Linux bridge. The kernel switchdev layer, and DSA driver, ensure
|
|
switch functions are "offloaded" to the HW switch, i.e., all traffic
|
|
between LAN ports never reach the CPU. For this you need the iproute2
|
|
suite of tools.
|