f089aa9877
The kernel is from upstream with a few extras to reduce the size of the 'aspeed_g5' zImage because it is too big for the flash layout. Mainline U-Boot has enough support to load the kernel from the flash device and from network but it is still behind the OpenBMC branch where most the development is done. The main resulting file from the build is a flash image. The partition layout matches the OpenBMC one for 32M chips. It makes it easier to update the different partitions from Linux. Intermediate files can be used to boot from U-Boot over the network or to boot QEMU using -kernel/-initrd/-dtb. Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
81 lines
1.8 KiB
Plaintext
81 lines
1.8 KiB
Plaintext
Aspeed AST2500 EVB
|
|
|
|
Introduction
|
|
============
|
|
|
|
The AST2500 EVB is an evaluation board for the AST2500 SoC, most
|
|
commonly used as a Server Management Processor. It includes an 800MHz
|
|
ARM11 processor with DDR3 or DDR4 SDRAM (up to 1GB), SPI flash memory
|
|
devices for BMC and host firmwares and numerous controllers to drive
|
|
the server board.
|
|
|
|
https://www.aspeedtech.com/server_ast2500/
|
|
|
|
How to build it
|
|
===============
|
|
|
|
Configure buildroot:
|
|
|
|
$ make aspeed_ast2500evb_defconfig
|
|
|
|
Compile everything and build the rootfs image:
|
|
|
|
$ make
|
|
|
|
Result of the build
|
|
===================
|
|
|
|
After building, the output/images directory contains:
|
|
|
|
output/images/
|
|
├── aspeed-ast2500-evb.dtb
|
|
├── flash.img
|
|
├── image.itb
|
|
├── rootfs.cpio
|
|
├── rootfs.cpio.xz
|
|
├── rootfs.tar
|
|
├── u-boot.bin
|
|
└── zImage
|
|
|
|
Flashing the image
|
|
==================
|
|
|
|
To update the contents of the first flash device, copy flash.img :
|
|
|
|
$ flashcp flash.img /dev/mtd0
|
|
|
|
or simply the boot loader:
|
|
|
|
$ flashcp u-boot.bin /dev/mtd1
|
|
|
|
Preparing the board
|
|
===================
|
|
|
|
* Connect a serial line to the board
|
|
* Power-up the board
|
|
|
|
Booting the board
|
|
=================
|
|
|
|
The AST2500 EVB boots from the SPI flash device directly and loads a
|
|
first bootloader (usually U-Boot). U-Boot will attempt to load a Linux
|
|
kernel from the same flash device by default but other storage could
|
|
be used.
|
|
|
|
* from U-Boot
|
|
|
|
The FIT image image.itb can be used to boot the board from U-Boot
|
|
using tftp
|
|
|
|
* with QEMU
|
|
|
|
$ qemu-system-arm -M ast2500-evb \
|
|
-drive file=output/images/flash.img,format=raw,if=mtd \
|
|
-nographic
|
|
|
|
$ qemu-system-arm -M ast2500-evb \
|
|
-kernel output/images/zImage \
|
|
-initrd output/images/rootfs.cpio \
|
|
-dtb output/images/aspeed-ast2500-evb.dtb \
|
|
-nographic
|