kumquat-buildroot/docs/manual/adding-packages-autotargets.txt
Arnout Vandecappelle (Essensium/Mind) 46fa5cbfb8 Rename XXXTARGETS to xxx-package
With the introduction of a specific macro for host targets, it was decided
to also make the names of the macros more intuitive: generic-package,
autotools-package and cmake-package.

Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
2012-07-17 20:22:41 +02:00

170 lines
7.0 KiB
Plaintext

Infrastructure for autotools-based packages
-------------------------------------------
[[autotargets-tutorial]]
+autotools-package+ tutorial
~~~~~~~~~~~~~~~~~~~~~~
First, let's see how to write a +.mk+ file for an autotools-based
package, with an example :
------------------------
01: #############################################################
02: #
03: # libfoo
04: #
05: #############################################################
06: LIBFOO_VERSION = 1.0
07: LIBFOO_SOURCE = libfoo-$(LIBFOO_VERSION).tar.gz
08: LIBFOO_SITE = http://www.foosoftware.org/download
09: LIBFOO_INSTALL_STAGING = YES
10: LIBFOO_INSTALL_TARGET = YES
11: LIBFOO_CONF_OPT = --enable-shared
12: LIBFOO_DEPENDENCIES = libglib2 host-pkg-config
13:
14: $(eval $(autotools-package))
------------------------
On line 6, we declare the version of the package.
On line 7 and 8, we declare the name of the tarball and the location
of the tarball on the Web. Buildroot will automatically download the
tarball from this location.
On line 9, we tell Buildroot to install the package to the staging
directory. The staging directory, located in +output/staging/+
is the directory where all the packages are installed, including their
development files, etc. By default, packages are not installed to the
staging directory, since usually, only libraries need to be installed in
the staging directory: their development files are needed to compile
other libraries or applications depending on them. Also by default, when
staging installation is enabled, packages are installed in this location
using the +make install+ command.
On line 10, we tell Buildroot to also install the package to the
target directory. This directory contains what will become the root
filesystem running on the target. Usually, we try not to install header
files and to install stripped versions of the binary. By default, target
installation is enabled, so in fact, this line is not strictly
necessary. Also by default, packages are installed in this location
using the +make install+ command.
On line 11, we tell Buildroot to pass a custom configure option, that
will be passed to the +./configure+ script before configuring
and building the package.
On line 12, we declare our dependencies, so that they are built
before the build process of our package starts.
Finally, on line line 14, we invoke the +autotools-package+
macro that generates all the Makefile rules that actually allows the
package to be built.
[[autotargets-reference]]
+autotools-package+ reference
~~~~~~~~~~~~~~~~~~~~~~~
The main macro of the autotools package infrastructure is
+autotools-package+. It is similar to the +generic-package+ macro. The ability to
have target and host packages is also available, with the
+host-autotools-package+ macro.
Just like the generic infrastructure, the autotools infrastructure
works by defining a number of variables before calling the
+autotools-package+ macro.
First, all the package metadata information variables that exist in the
generic infrastructure also exist in the autotools infrastructure:
+LIBFOO_VERSION+, +LIBFOO_SOURCE+,
+LIBFOO_PATCH+, +LIBFOO_SITE+,
+LIBFOO_SUBDIR+, +LIBFOO_DEPENDENCIES+,
+LIBFOO_INSTALL_STAGING+, +LIBFOO_INSTALL_TARGET+.
A few additional variables, specific to the autotools infrastructure,
can also be defined. Many of them are only useful in very specific
cases, typical packages will therefore only use a few of them.
* +LIBFOO_SUBDIR+ may contain the name of a subdirectory
inside the package that contains the configure script. This is useful,
if for example, the main configure script is not at the root of the
tree extracted by the tarball. If +HOST_LIBFOO_SUBDIR+ is
not specified, it defaults to +LIBFOO_SUBDIR+.
* +LIBFOO_CONF_ENV+, to specify additional environment
variables to pass to the configure script. By default, empty.
* +LIBFOO_CONF_OPT+, to specify additional configure
options to pass to the configure script. By default, empty.
* +LIBFOO_MAKE+, to specify an alternate +make+
command. This is typically useful when parallel make is enabled in
the configuration (using +BR2_JLEVEL+) but that this
feature should be disabled for the given package, for one reason or
another. By default, set to +$(MAKE)+. If parallel building
is not supported by the package, then it should be set to
+LIBFOO_MAKE=$(MAKE1)+.
* +LIBFOO_MAKE_ENV+, to specify additional environment
variables to pass to make in the build step. These are passed before
the +make+ command. By default, empty.
* +LIBFOO_MAKE_OPT+, to specify additional variables to
pass to make in the build step. These are passed after the
+make+ command. By default, empty.
* +LIBFOO_AUTORECONF+, tells whether the package should
be autoreconfigured or not (i.e, if the configure script and
Makefile.in files should be re-generated by re-running autoconf,
automake, libtool, etc.). Valid values are +YES+ and
+NO+. By default, the value is +NO+
* +LIBFOO_AUTORECONF_OPT+ to specify additional options
passed to the 'autoreconf' program if
+LIBFOO_AUTORECONF=YES+. By default, empty.
* +LIBFOO_LIBTOOL_PATCH+ tells whether the Buildroot
patch to fix libtool cross-compilation issues should be applied or
not. Valid values are +YES+ and +NO+. By
default, the value is +YES+
* +LIBFOO_INSTALL_STAGING_OPT+ contains the make options
used to install the package to the staging directory. By default, the
value is +DESTDIR=$$(STAGING_DIR) install+, which is
correct for most autotools packages. It is still possible to override
it.
* +LIBFOO_INSTALL_TARGET_OPT+ contains the make options
used to install the package to the target directory. By default, the
value is +DESTDIR=$$(TARGET_DIR) install+. The default
value is correct for most autotools packages, but it is still possible
to override it if needed.
* +LIBFOO_CLEAN_OPT+ contains the make options used to
clean the package. By default, the value is +clean+.
* +LIBFOO_UNINSTALL_STAGING_OPT+, contains the make
options used to uninstall the package from the staging directory. By
default, the value is +DESTDIR=$$(STAGING_DIR) uninstall+.
* +LIBFOO_UNINSTALL_TARGET_OPT+, contains the make
options used to uninstall the package from the target directory. By
default, the value is +DESTDIR=$$(TARGET_DIR) uninstall+.
With the autotools infrastructure, all the steps required to build
and install the packages are already defined, and they generally work
well for most autotools-based packages. However, when required, it is
still possible to customize what is done in any particular step:
* By adding a post-operation hook (after extract, patch, configure,
build or install). See the reference documentation of the generic
infrastructure for details.
* By overriding one of the steps. For example, even if the autotools
infrastructure is used, if the package +.mk+ file defines its
own +LIBFOO_CONFIGURE_CMDS+ variable, it will be used
instead of the default autotools one. However, using this method
should be restricted to very specific cases. Do not use it in the
general case.