kumquat-buildroot/board/olimex/a20_olinuxino/readme.txt
Jan Viktorin aa8c11105d olimex_a20_olinuxino_lime2: new board
It is based on olimex_a20_olinuxino_lime configuration. Tested on the mainline
kernel 4.1.4. It boots and the Ethernet is working at speed 1 Gbps.

[Thomas: remove ccache and optimize 2 options.]

Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Acked-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
2015-10-03 14:50:47 +01:00

117 lines
3.5 KiB
Plaintext

A20-OLinuXino-LIME and A20-OLinuXino-MICRO
Intro
=====
These are open hardware boards, both based an the AllWinners A20 SoC.
for more details about the boards see the following pages:
- https://www.olimex.com/Products/OLinuXino/open-source-hardware
- https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXino-MICRO/
- https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXino-LIME/
The following defconfigs are available:
- olimex_a20_olinuxino_micro_defconfig
for the A20-OLinuXino-MICRO board using mainline kernel
- olimex_a20_olinuxino_lime_defconfig
for the A20-OLinuXino-LIME board using mainline kernel
- olimex_a20_olinuxino_lime_mali_defconfig
for the A20-OLinuXino-LIME board using legacy linux-sunxi kernel
- olimex_a20_olinuxino_lime2_defconfig
for the A20-OLinuXino-LIME2 board using mainline kernel
The legacy linux-sunxi kernels are based on the vendor code drops.
They are only useful when accelerated 3D graphics and multimedia support
is strictly necessary.
The Mainline Kernel is already a much better choice for a headless server.
And also the mainline kernel works fine even for a basic Linux desktop
system running on top of a simple framebuffer, which may be good enough for
the users who do not need fancy 3D graphics or video playback acceleration.
(see http://linux-sunxi.org/Linux_Kernel for more details)
How to build it
===============
Configure Buildroot:
$ make <board>_defconfig
Compile everything and build the rootfs image:
$ make
Result of the build
-------------------
After building, you should get a tree like this:
output/images/
+-- rootfs.ext2
+-- rootfs.ext4 -> rootfs.ext2
+-- script.bin (lime_mali)
+-- sun7i-a20-olinuxino-lime.dtb (lime, mainline)
+-- sun7i-a20-olinuxino-lime2.dtb (lime2, mainline)
+-- sun7i-a20-olinuxino-micro.dtb (micro, mainline)
+-- u-boot.bin
+-- u-boot-sunxi-with-spl.bin
`-- zImage
How to write the SD card
========================
Prepare the SD card
-------------------
Erase existing stuff, and create an unique Linux partition with `fdisk`.
# fdisk /dev/sdX
Command (m for help): o
Building a new DOS disklabel with disk identifier 0xf9e1616a.
Changes will remain in memory only, until you decide to write them.
After that, of course, the previous content won't be recoverable.
Command (m for help): n
Partition type:
p primary (0 primary, 0 extended, 4 free)
e extended
Select (default p): p
Partition number (1-4, default 1): 1
First sector (2048-7626751, default 2048): 2048
Last sector, +sectors or +size{K,M,G} (2048-7626751, default 7626751):
Using default value 7626751
Command (m for help): p
Disk /dev/sdX: 3904 MB, 3904897024 bytes
4 heads, 16 sectors/track, 119168 cylinders, total 7626752 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xf9e1616a
Device Boot Start End Blocks Id System
/dev/sdX1 2048 7626751 3812352 83 Linux
Command (m for help): w
The partition table has been altered!
Calling ioctl() to re-read partition table.
Syncing disks.
Copy images on the SD card
--------------------------
# dd if=output/images/rootfs.ext2 of=/dev/sdX1
# dd if=output/images/u-boot-sunxi-with-spl.bin of=/dev/sdX bs=1024 seek=8
Finish
======
Eject the SD card, insert it in the A20-OLinuXino board, and power it up.