ada40afb32
The pi3-minuart-bt Device Tree overlay has been renamed to miniuart-bt, as it is useful/usable for other platforms than the RPi3. So we use this DT overlay and rename the --add-pi3-miniuart-bt-overlay option to --add-miniuart-bt-overlay accordingly. Signed-off-by: Arthur Courtel <arthur.courtel@smile.fr> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
100 lines
2.4 KiB
Plaintext
100 lines
2.4 KiB
Plaintext
Raspberry Pi
|
|
|
|
Intro
|
|
=====
|
|
|
|
These instructions apply to all models of the Raspberry Pi:
|
|
- the original models A and B,
|
|
- the "enhanced" models A+ and B+,
|
|
- the model B2 (aka Raspberry Pi 2)
|
|
- the model B3 (aka Raspberry Pi 3).
|
|
- the model B4 (aka Raspberry Pi 4).
|
|
|
|
How to build it
|
|
===============
|
|
|
|
Configure Buildroot
|
|
-------------------
|
|
|
|
There are two RaspberryPi defconfig files in Buildroot, one for each
|
|
major variant, which you should base your work on:
|
|
|
|
For models A, B, A+ or B+:
|
|
|
|
$ make raspberrypi_defconfig
|
|
|
|
For model Zero (model A+ in smaller form factor):
|
|
|
|
$ make raspberrypi0_defconfig
|
|
|
|
For model 2 B:
|
|
|
|
$ make raspberrypi2_defconfig
|
|
|
|
For model 3 B and B+:
|
|
|
|
$ make raspberrypi3_defconfig
|
|
|
|
For model 4 B:
|
|
|
|
$ make raspberrypi4_defconfig
|
|
|
|
Build the rootfs
|
|
----------------
|
|
|
|
Note: you will need to have access to the network, since Buildroot will
|
|
download the packages' sources.
|
|
|
|
You may now build your rootfs with:
|
|
|
|
$ make
|
|
|
|
(This may take a while, consider getting yourself a coffee ;-) )
|
|
|
|
Result of the build
|
|
-------------------
|
|
|
|
After building, you should obtain this tree:
|
|
|
|
output/images/
|
|
+-- bcm2708-rpi-b.dtb [1]
|
|
+-- bcm2708-rpi-b-plus.dtb [1]
|
|
+-- bcm2709-rpi-2-b.dtb [1]
|
|
+-- bcm2710-rpi-3-b.dtb [1]
|
|
+-- bcm2710-rpi-3-b-plus.dtb [1]
|
|
+-- bcm2711-rpi-4-b.dtb [1]
|
|
+-- boot.vfat
|
|
+-- rootfs.ext4
|
|
+-- rpi-firmware/
|
|
| +-- bootcode.bin
|
|
| +-- cmdline.txt
|
|
| +-- config.txt
|
|
| +-- fixup.dat
|
|
| +-- start.elf
|
|
| `-- overlays/ [2]
|
|
+-- sdcard.img
|
|
`-- zImage
|
|
|
|
[1] Not all of them will be present, depending on the RaspberryPi
|
|
model you are using.
|
|
|
|
[2] Only for the Raspberry Pi 3/4 Models (overlay miniuart-bt is needed
|
|
to enable the RPi3 serial console otherwise occupied by the bluetooth
|
|
chip). Alternative would be to disable the serial console in cmdline.txt
|
|
and /etc/inittab.
|
|
|
|
How to write the SD card
|
|
========================
|
|
|
|
Once the build process is finished you will have an image called "sdcard.img"
|
|
in the output/images/ directory.
|
|
|
|
Copy the bootable "sdcard.img" onto an SD card with "dd":
|
|
|
|
$ sudo dd if=output/images/sdcard.img of=/dev/sdX
|
|
|
|
Insert the SDcard into your Raspberry Pi, and power it up. Your new system
|
|
should come up now and start two consoles: one on the serial port on
|
|
the P1 header, one on the HDMI output where you can login using a USB
|
|
keyboard.
|