c45b2f2b9d
Signed-off-by: Francois Perrad <francois.perrad@gadz.org> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
88 lines
2.4 KiB
Plaintext
88 lines
2.4 KiB
Plaintext
**************
|
|
NXP LS1028ARDB
|
|
**************
|
|
|
|
This file documents the Buildroot support for the LS1028A Reference Design Board.
|
|
|
|
for more details about the board and the QorIQ Layerscape SoC, see the following pages:
|
|
- https://www.nxp.com/design/qoriq-developer-resources/layerscape-ls1028a-reference-design-board:LS1028ARDB
|
|
- https://www.nxp.com/LS1028A
|
|
|
|
for the software NXP LSDK (Layerscape Software Development Kit), see
|
|
- https://www.nxp.com/docs/en/user-guide/LSDKUG_Rev21.08.pdf
|
|
|
|
the components from NXP are:
|
|
- rcw, LSDK 21.08
|
|
- atf (fork), LSDK 21.08
|
|
- uboot (fork), LSDK 21.08
|
|
- cadence-dp-firmware (blob), LSDK 20.12
|
|
- linux (fork), LSDK 21.08
|
|
|
|
Build
|
|
=====
|
|
|
|
First, configure Buildroot for the LS1028ARDB board:
|
|
|
|
make ls1028ardb_defconfig
|
|
|
|
Build all components:
|
|
|
|
make
|
|
|
|
You will find in output/images/ the following files:
|
|
- bl2_sd.pbl
|
|
- fip.bin
|
|
- fsl-ls1028a-rdb.dtb
|
|
- Image
|
|
- PBL.bin
|
|
- rootfs.ext2
|
|
- rootfs.ext4 -> rootfs.ext2
|
|
- sdcard.img
|
|
- u-boot.bin
|
|
|
|
Create a bootable SD card
|
|
=========================
|
|
|
|
To determine the device associated to the SD card have a look in the
|
|
/proc/partitions file:
|
|
|
|
cat /proc/partitions
|
|
|
|
Buildroot prepares a bootable "sdcard.img" image in the output/images/
|
|
directory, ready to be dumped on a SD card. Launch the following
|
|
command as root:
|
|
|
|
dd if=output/images/sdcard.img of=/dev/sdX
|
|
|
|
*** WARNING! This will destroy all the card content. Use with care! ***
|
|
|
|
For details about the medium image layout, see the definition in
|
|
board/freescale/ls1028ardb/genimage.cfg.
|
|
|
|
Boot the LS1028ARDB board
|
|
=========================
|
|
|
|
To boot your newly created system:
|
|
- insert the SD card in the SD slot of the board;
|
|
- Configure the switches SW2[1:4] = 1000 (select SD Card boot option)
|
|
- put a DB9F cable into the UART1 Port and connect using a terminal
|
|
emulator at 115200 bps, 8n1;
|
|
- power on the board.
|
|
|
|
The Cadence DP (Display Port) firmware must loaded from uboot with the following commands:
|
|
|
|
=> ext2load mmc 0 0x80000000 /boot/ls1028a-dp-fw.bin
|
|
102464 bytes read in 24 ms (4.1 MiB/s)
|
|
=> hdp load 0x80000000 0x2000
|
|
Loading hdp firmware from 0x0000000080000000 offset 0x0000000000002000
|
|
Loading hdp firmware Complete
|
|
=> boot
|
|
|
|
The interfaces of Ethernet switch (Felix DSA) are bring up with the following commands:
|
|
|
|
ip link set eno2 up
|
|
ip link set swp0 up
|
|
ip link set swp1 up
|
|
ip link set swp2 up
|
|
ip link set swp3 up
|