d9ccd8f0fc
QT_QPA_EGLFS_ALWAYS_SET_MODE=1 needs to be exported, otherwise the Qt5 Cinematic demo throws a storm of the following messages: Could not queue DRM page flip on screen LVDS1 (Invalid argument) Improve the instructions by mentioning such requirement. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
112 lines
2.9 KiB
Plaintext
112 lines
2.9 KiB
Plaintext
*******************************
|
|
Freescale i.MX6 Sabre SD boards
|
|
*******************************
|
|
|
|
This file documents the Buildroot support for the Freescale i.MX6 Sabre SD
|
|
boards based on i.MX6Q, i.MX6DL and iMX6QP.
|
|
|
|
Thanks to the SPL support in U-Boot it is possible to run a single
|
|
sdcard.img in all i.MX6 Sabre SD board variants.
|
|
|
|
This configuration uses U-Boot mainline and kernel mainline.
|
|
|
|
Build
|
|
=====
|
|
|
|
First, configure Buildroot for the i.MX6 Sabre SD board:
|
|
|
|
make imx6-sabresd_defconfig
|
|
|
|
Build all components:
|
|
|
|
make
|
|
|
|
You will find the following files in output/images/ :
|
|
- imx6q-sabresd.dtb
|
|
- imx6dl-sabresd.dtb
|
|
- imx6qp-sabresd.dtb
|
|
- rootfs.ext4
|
|
- rootfs.tar
|
|
- sdcard.img
|
|
- u-boot.imx
|
|
- zImage
|
|
|
|
Create a bootable SD card
|
|
=========================
|
|
|
|
To determine the device associated to the SD card have a look in the
|
|
/proc/partitions file:
|
|
|
|
cat /proc/partitions
|
|
|
|
Buildroot prepares a bootable "sdcard.img" image in the output/images/
|
|
directory, ready to be dumped on a SD card. Launch the following
|
|
command as root:
|
|
|
|
dd if=output/images/sdcard.img of=/dev/<your-sd-device>
|
|
|
|
*** WARNING! This will destroy all the card content. Use with care! ***
|
|
|
|
For details about the medium image layout, see the definition in
|
|
board/freescale/common/imx/genimage.cfg.template.
|
|
|
|
Boot the i.MX6 Sabre SD board
|
|
=============================
|
|
|
|
To boot your newly created system:
|
|
- insert the SD card in the SD3 slot of the board (close to the HDMI connector);
|
|
- put a micro USB cable into the Debug USB Port and connect using a terminal
|
|
emulator at 115200 bps, 8n1;
|
|
- power on the board.
|
|
|
|
Testing graphics on the i.MX6 Sabre SD board
|
|
============================================
|
|
|
|
The imx6-sabresd_qt5_defconfig allows to quickly test the graphics
|
|
capabilities of i.MX6 using the opensource Etnaviv graphics stack
|
|
and kernel mainline.
|
|
|
|
In order to build it:
|
|
|
|
make imx6-sabresd_qt5_defconfig
|
|
make
|
|
|
|
Then flash the SD card as explained above.
|
|
|
|
Running kmscube application:
|
|
|
|
# kmscube
|
|
|
|
Running Qt5 Cinematic Demo:
|
|
|
|
# export QT_QPA_EGLFS_KMS_CONFIG=/root/sabresd.json
|
|
# export QT_QPA_EGLFS_ALWAYS_SET_MODE=1
|
|
# /usr/share/Qt5/CinematicExperience/Qt5_CinematicExperience
|
|
|
|
Running gl2mark benchmark:
|
|
|
|
# glmark2-es2-drm
|
|
|
|
Testing video playback on the i.MX6 Sabre SD board
|
|
==================================================
|
|
|
|
As the mx6sabresd has two display outputs (LVDS and HDMI), it is necessary to
|
|
know what is the connector that corresponds to the HDMI output.
|
|
|
|
This information can be found by running:
|
|
|
|
# modetest
|
|
|
|
And search for the HDMI connector number. In our case it shows up as 37.
|
|
|
|
In the mx6sabresd prompt run the following Gstreamer pipeline:
|
|
|
|
# gst-launch-1.0 filesrc location=/root/trailer_1080p_h264_mp3.avi ! avidemux ! \
|
|
h264parse ! v4l2video1dec capture-io-mode=dmabuf ! kmssink connector-id=37 \
|
|
name=imx-drm sync=0
|
|
|
|
(The video used on this example was retrieved from:
|
|
http://linode.boundarydevices.com/videos/trailer_1080p_h264_mp3.avi)
|
|
|
|
Enjoy!
|