Most of the users use HDMI console on RPi and with increasing popularity
of systemd they face a trouble.
systemd doesn't use /etc/inittab, enable getty@tty1.service instead.
Signed-off-by: Alexey Roslyakov <alexey.roslyakov@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Most rpi defconfigs use dtb overlays, but not rpi0 / rpi2 - Making it harder
to use overlays on those boards as the genimage files have to be tweaked.
To fix this, create the rpi-firmware/overlays directory in the post-build
script if needed and unconditionally include it in the genimage files so
rpi0/rpi2 works consistently with the other variants.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Currently, the cmdline.txt file is installed in $(BINARIES_DIR) by the
rpi-firmware package. Overriding files in there can not be done with an
overlay (which only applies to $(TARGET_DIR)), and thus requires using
either a post-build or post-image script, which is not always very
practical when a custom file must be used.
Like was done in 689b9ac439 (package/rpi-firmware: rework boot/config
file handling) for config.txt, add an option to allow users to specify
the path to a custom cmdline.txt.
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The CM4 IO Board is equipped with an on-board RTC connected over I2C,
and has USB 2.0 host ports.
This commit loads the appropriate overlays to enable both. The USB 2.0
interface is by default disabled on CM4 to reduce the power
consumption so it needs to be explicitly enabled on the CM4 IO Board
to use the USB ports.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The CM4 IO Board is equipped with an on-board RTC connected over I2C,
and has USB 2.0 host ports.
This commit loads the appropriate overlays to enable both. The USB 2.0
interface is by default disabled on CM4 to reduce the power
consumption so it needs to be explicitly enabled on the CM4 IO Board
to use the USB ports.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The Raspberry-Pi Zero 2 W is an affordable single board computer. It is
a more powerful drop-in replacement for the Raspberry Pi Zero W.
The board incorporates an Raspberry-Pi RP3A0 system-in-package (SiP) with
a Broadcom BCM2710A1 and 512MB LPDDR2 SDRAM. The CPU is a quad-core 1Ghz
64-bit Arm Cortex-A53. As for other Raspberry-Pis it also provides
2.4GHz 802.11 b/g/n Wifi, Bluetooth 4.2 and BLE.
The BCM2710 cpu is similar to the Raspberry-Pi 3, it uses the same
kernel configuration as the Raspberry-Pi 2 and 3.
Signed-off-by: Julien Grossholtz <julien.grossholtz@openest.io>
[Based on https://patchwork.ozlabs.org/project/buildroot/patch/20211030213600.3445223-3-julien.grossholtz@openest.io/
- reformat genimage-raspberrypizero2w.cfg according to the beautify patch-set
- update kernel version to 9878a11 (5.10.78)
- use new bcm2710-rpi-zero-2-w dtb
- update commit log about kernel config (RPi2/3)
- add DEVELOPERS entries for Julien
]
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Add missing dtb files:
- bcm2708-rpi-cm.dtb from genimage-raspberrypi.cfg
- bcm2708-rpi-zero.dtb from genimage-raspberrypi0.cfg:
- bcm2708-rpi-zero-w.dtb from genimage-raspberrypi0w.cfg
- bcm2710-rpi-cm3.dtb from genimage-raspberrypi3.cfg
- bcm2837-rpi-3-b.dtb from genimage-raspberrypi3-64.cfg
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Try to be less smart (focused on the one target/one use-case),
instead reduce the rpi-firmware package to a selectable list
of (verbatim) installed firmware files.
- change rpi-firmware config handling from rpi-variant/rpi-flavour
choices to bootcode.bin, pi-default/-extended/-cut-down and
pi4-/default/-extended/-cut-down selection
- add BR2_PACKAGE_RPI_FIRMWARE_CONFIG_FILE option to select installable
config.txt file
- remove config.txt modify code/handling from raspberry post-image.sh
script
- add different customized config.txt files to the raspberry board
section
- change dtoverlay krnbt from 'dtoverlay=miniuart-bt,krnbt=on' to extra line
with explanation comment
- change raspberry defconfigs to select appropiate rpi-firmware
and config.txt files
- change genimage-raspberrypi4.cfg/genimage-raspberrypi4-64.cfg to
use start4.elf and fixup4.dat
- update board/raspberrypi/readme.txt (add optional files fixup4.dat,
start4.elf and zImage)
With this changes a better support for custom use-cases should
be possible, specially multi-target SD cards as suggested by
Stefan Agner ([1]).
[1] http://lists.busybox.net/pipermail/buildroot/2021-February/303318.html
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
[yann.morin.1998@free.fr: fix case of no config.txt provided]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The default setting with miniuart-bt requires hciattach which is a
deprecated utility in BlueZ. Setting the krnbt parameter switches to
the modern method of using serdev in the kernel removing the need for
any userspace configuration to enable the Bluetooth controller.
This is documented as applying to all Raspberry Pi variants so just
enable it globally.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since commit 'package/rpi-firmware: fix startup file names' ([1]) the
start and fixup file names are normalized to start.elf/fixup.dat,
adjust the rpi4 genimage config files accordingly.
Fixes:
ERROR: file(rpi-firmware/fixup4.dat): stat(.../images/rpi-firmware/fixup4.dat) failed: No such file or directory
ERROR: vfat(boot.vfat): could not setup rpi-firmware/fixup4.dat
[1] https://git.buildroot.net/buildroot/commit/?id=1bdc0334ff6273761b2e7fda730cdcc7e1f46862
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This configuration builds a 64bit image for RaspberryPi 4.
Signed-off-by: Arthur Courtel <arthur.courtel@smile.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The pi3-minuart-bt Device Tree overlay has been renamed to
miniuart-bt, as it is useful/usable for other platforms than the
RPi3. So we use this DT overlay and rename the
--add-pi3-miniuart-bt-overlay option to --add-miniuart-bt-overlay
accordingly.
Signed-off-by: Arthur Courtel <arthur.courtel@smile.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use the pi3-miniuart-bt device tree overlay (as the 32bit raspberrypi3
defconfig) instead of the enable_uart option.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
genimage makes a full copy of the given rootpath to ${GENIMAGE_TMP}/root
so passing TARGET_DIR would be a waste of time and disk space. We don't
rely on genimage to build the rootfs image, just to insert a pre-built
one in the disk image.
Signed-off-by: Carlos Santos <unixmania@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since the bump to the 20190819 snapshot there is now a dedicated dts file
for the rpi0, so use that rather than the rpi-b-plus one:
bd1336d8b6
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes#12816
Commit 42d22f3bdb ({configs/raspberrypi,package/rpi-firmware}: bump
kernel/firmware to 20190819 version) updated the kernel version but failed
to take into consideration that the rpi0w dts file has been renamed:
6f91b5dbfd
Fix it by renaming the dts/dtb file referenced from the kernel build and
genimage.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This is based on the pi3 defconfig. There is currently no 64-bit support
since the upstream kernel does not build in this configuration.
Signed-off-by: Michael Cullen <michael@michaelcullen.name>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch enables the inclusion of the Pi's overlays. Previously
the overlays were not included in the genimage configuration.
This patch ensures overlays are included in the sdcard (when
enabled) by defaulting to the inclusion of an empty
output/images/rpi-firmware/overlays directory in genimage cfg.
The Pi's overlays are built with the following config
variables:
BR2_PACKAGE_RPI_FIRMWARE=y
BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTBS=y
BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS=y
BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
BR2_LINUX_KERNEL_IMAGE_NAME="Image"
BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="Image modules dtbs"
After building, the dtbo files are present in the
output/images/rpi-firmware/overlays directory but not added
to the sdcard because they are missing from the genimage cfg
file.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
[Arnout: fix indentation, and add comment explaining why an empty
directory is created.]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
As per latest Raspberry Pi firmware documentation, the option
'arm_control' has been deprecated in favor of 'arm_64bit'.
Fixes https://bugs.busybox.net/show_bug.cgi?id=11111.
Signed-off-by: Jason Tang <tang@jtang.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The kernel now includes the rpi3b+ device tree for aarch64
Signed-off-by: Martin Bark <martin@barkynet.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Up to now, Raspberry Pi Zero W (rpi0w) could be built with the normal
raspberrypi0_defconfig. However, then you don't have support for the
Bluetooth out-of-the-box, which makes using a W a bit pointless.
Therefore, create a separate defconfig for the W. It is a copy of
raspberrypi0_defconfig with the following changes:
- Add DT overlays (from rpi-firmware) to support Bluetooth.
- Pass --add-pi3-miniuart-bt-overlay to post-image.sh.
Since there is now a separate raspberrypi0w_defconfig, the W support
can be removed from raspberrypi0_defconfig.
Signed-off-by: Yves Deweerdt <yves.deweerdt.linux@gmail.com>
[Arnout:
- Bump to same kernel version as raspberrypi0.
- Remove redundant comment.
- Remove redundant default BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS=y.
- Improve commit log.
- Refresh .gitlab-ci.yml.
]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
The gpu_mem option is not using the proper option argument which causes sed to
fail.
+ case "${arg}" in
+ gpu_mem=ome/gportay/output-rpi3-qtwe/images
+ sed -e '/^ome/gportay/output-rpi3-qtwe/images=/s,=.*,=ome/gportay/output-rpi3-qtwe/images,' -i /home/gportay/output-rpi3-qtwe/images/rpi-firmware/config.txt
sed: -e expression #1, char 8: extra characters after command
+ case "${arg}" in
+ gpu_mem=ome/gportay/output-rpi3-qtwe/images
+ sed -e '/^ome/gportay/output-rpi3-qtwe/images=/s,=.*,=ome/gportay/output-rpi3-qtwe/images,' -i /home/gportay/output-rpi3-qtwe/images/rpi-firmware/config.txt
sed: -e expression #1, char 8: extra characters after command
The issue comes from the use of $1 instead of $arg to extract the gpu_mem
value. $1 is the $(BINARIES_DIR) which leads to a sed expression error.
Also, it adds the error flag to the shell script to prevent from such situation
and terminate the build in error.
Signed-off-by: Gaël PORTAY <gael.portay@savoirfairelinux.com>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The amount of GPU memory can be set using the new option --gpu_mem_XXX
(where XXX is the total amount of memory available on the board).
Signed-off-by: Gaël PORTAY <gael.portay@savoirfairelinux.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This configuration builds a 64bit image for RaspberryPi 3.
The size of the ext4 filesystem has to be extended to fit the large amount
(~60MB) of kernel modules enabled in the defconfig.
[Peter: drop gcc version selection / glibc, explain ext4 size requirement]
Signed-off-by: Gaël PORTAY <gael.portay@savoirfairelinux.com>
Tested-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
We no longer use the marked kernel.
Cc: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Since release 4.4 a kernel without a trailer is assumed to be device tree
capable. Since our Raspberry Pi defconfigs all use the newer firmware we can
just use the regular kernel image.
https://www.raspberrypi.org/documentation/configuration/device-tree.md
Tested on Raspberry Pi 3.
Cc: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
- enable BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS in raspberrypi3_defconfig
- add copy of rpi-firmware/overlays directory to boot partition in genimage-raspberrypi3.cfg
- enhance post-image.sh script to add 'dtoverlay=pi3-miniuart-bt' on request
- add BR2_ROOTFS_POST_SCRIPT_ARGS="--add-pi3-miniuart-bt-overlay" in raspberrypi3_defconfig
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As pointed out in bug #9161, we don't always have an inittab file (if
systemd or no init is used), so the post build script should only try to
tweak it if present.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for the rpi-0, which is basically a rpi (model A+) in a
smaller form-factor.
This one does not have an ethernet port, so we just remove it from the
configuration (or we could use the existing rasbperrypi_defconfig and
suffer from a longer boot time because of the waiting for eth0).
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
So far identical to the rpi2 one except for the dts file as the SW runs in
32bit mode.
[Peter: extend commit message]
Signed-off-by: Ubaldo Porcheddu <ubaldo@eja.it>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The defconfigs for the Raspberry Pi boards start a console on HDMI in
addition to the classic one on UART. Document this feature in the
readme.
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Arnout Vandecappelle <arnout@mind.be>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
