Since we will enable hash checks for git downloads soon, the hash check
for the custom git download should be disabled.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Since we will enable hash checks for git downloads soon, the hash check
for the custom git download should be disabled.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Instead of excluding the hash specifically for the custom tarball and
custom version cases, exclude it always except in the one case where
we do have a hash: the latest version.
This simplifies the code a little because soon we will add hash checks
for git as well, so we also need an exclusion in that case.
It is not needed to exclude it twice for barebox and barebox-aux,
because they use the same source tarball and barebox-aux can only be
enabled if barebox is enabled. So simplify even further by pulling
the exclusion logic out of inner-barebox-package.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Instead of excluding the hash specifically for the custom tarball and
custom version cases, exclude it always except in the one case where
we do have a hash: the latest version.
This simplifies the code a little because soon we will add hash checks
for git as well, so we also need an exclusion in that case.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The warning currently reads:
No board defconfig name specified, check your
BR2_TARGET_UBOOT_DEFCONFIG setting.
It should read:
No board defconfig name specified, check your
BR2_TARGET_UBOOT_BOARD_DEFCONFIG setting.
Signed-off-by: Christian Stewart <christian@paral.in>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Until now, the host toolchain was used to build syslinux, as it was
not possible to build a 32-bit syslinux with a x86-64 toolchain.
However, syslinux requires gnu-efi, and gnu-efi is built using the
target toolchain. Mixing different toolchains doesn't work well, so
this commit changes the syslinux package to use the target toolchain
for syslinux as well. This is made possible by patches
0003-Fix-ldlinux.elf-Not-enough-room-for-program-headers-.patch and
0004-memdisk-Force-ld-output-format-to-32-bits.patch.
Since syslinux also contains some utilities that have to run on the
host, those have to continue being built with the host toolchain,
which requires patch 0005-utils-Use-the-host-toolchain-to-build.patch.
Patch 0006-lzo-Use-the-host-toolchain-for-prepcore.patch is about
building prepcore, another utility with the host toolchain as it is
required at build-time.
This was tested using a Buildroot's built x86_64 toolchain, and
checked that the output binaries are 32-bits. It was tested as well if
they actually boot on hardware.
Signed-off-by: Benoît Allard <benoit.allard@greenbone.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We need to avoid failing of copy of custom dts using cp -f <>
command. So, just qstrip the variable as is done for other
configuration options.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Tested-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Similaly to Linux, this patch adds the ability to copy in and build
out-of-source device tree sources during a U-Boot build.
Signed-off-by: James Balean <james@balean.com.au>
Cc: Arnout Vandecappelle <arnout@mind.be>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
In preparation for the addition of more patches to the syslinux
package, reformat the two existing patches as proper Git formatted
patches.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We want to use SPDX identifier for license string as much as possible.
SPDX short identifier for BSD-2c is BSD-2-Clause.
This change is done using following command.
find . -name "*.mk" | xargs sed -ri '/LICENSE( )?[\+:]?=/s/BSD-2c/BSD-2-Clause/g'
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We want to use SPDX identifier for license string as much as possible.
SPDX short identifier for BSD-3c is BSD-3-Clause.
This change is done using following command.
find . -name "*.mk" | xargs sed -ri '/LICENSE( )?[\+:]?=/s/BSD-3c/BSD-3-Clause/g'
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We want to use SPDX identifier for license string as much as possible.
SPDX short identifier for LGPLv2.1/LGPLv2.1+ is LGPL-2.1/LGPL-2.1+.
This change is done using following command.
find . -name "*.mk" | xargs sed -ri '/LICENSE( )?[\+:]?=/s/LGPLv2.1(\+)?/LGPL-2.1\1/g'
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We want to use SPDX identifier for license string as much as possible.
SPDX short identifier for GPLv3/GPLv3+ is GPL-3.0/GPL-3.0+.
This change is done using following command.
find . -name "*.mk" | xargs sed -ri '/LICENSE( )?[\+:]?=/s/\<GPLv3\>/GPL-3.0/g'
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We want to use SPDX identifier for license strings as much as possible.
SPDX short identifier for GPLv2/GPLv2+ is GPL-2.0/GPL-2.0+.
This change is done by using following command.
find . -name "*.mk" | xargs sed -ri '/LICENSE( )?[\+:]?=/s/\<GPLv2\>/GPL-2.0/g'
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
SPL is the name used for spl on i.MX6, so update the same on
BR2_TARGET_UBOOT_SPL_NAME help text.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas: rewrap Config.in help text.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
On older SoCFPGA SoCs, there was not enough SRAM to fit the entire
U-Boot, so a SPL model was used. The SPL was therefore the binary that
had to be "prepared" to be loaded by the ROM code using the mkpimage
tool.
With newer SoCFPGA SoCs, there is enough SRAM to fit the entire U-Boot,
and therefore the ROM code directly loads U-Boot. In this case, it's the
real U-Boot image (not the SPL) that needs to be prepared using
mkpimage.
This code adds support for the newer SoCFPGA SoCs, by adjusting the
mkpimage related logic to apply on the SPL if an SPL is enabled, or on
the full U-Boot image otherwise.
Signed-off-by: Lionel Flandrin <lionel@svkt.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Commit 006a328ad6 ("util-linux: fix build with ncurses") removed
dependency on BR2_USE_WCHAR, but failed to update the reverse
dependencies of util-linux.
This commit fixes all such reverse dependencies by removing dependency
on BR2_USE_WCHAR as it is not required by package itself.
Fixes: 006a328ad6 ("util-linux: fix build with ncurses")
Signed-off-by: Rahul Bedarkar <rahul.bedarkar@imgtec.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Commit 3e3fef39e7 added new and improved
patch handling, with BR2_TARGET_UBOOT_PATCH. This was in addition to
the existing BR2_TARGET_UBOOT_CUSTOM_PATCH_DIR option, that only
handled directories.
Later, commit 21b25d28fc moved the old
BR2_TARGET_UBOOT_CUSTOM_PATCH_DIR to legacy options. But on the way,
bad things happened:
* The original option was a string, while the one added to Config.in.legacy
is a bool. This results in a warning from defconfigs that actually define
the old BR2_TARGET_UBOOT_CUSTOM_PATCH_DIR (because a string is not a valid
value for a bool), but it does not result in the legacy option being
selected. Consequently, BR2_LEGACY is not selected either.
* The advice at the top of Config.in.legacy to add a hidden WRAP option
to select BR2_LEGACY was not heeded.
* The advice at the top of Config.in.legacy to use the old string
option as the default for the new string option was not heeded. In
this case, the variable was not just renamed, as the old option
supported directories only, while the new one supports files too.
But since the old option is a subset of the new option, it can still
be used to set a useful default.
So, this mod turns the legacy option back to a string, adds a hidden
bool WRAP option to set BR2_LEGACY when the string is non emoty, and
uses the legacy option to set the default for the new option.
Signed-off-by: Danomi Manchego <danomimanchego123@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
When generating the environment image the target endianess should
be taken in account for CRC calculation purposes. For big endian
targets the -b flag should be passed to the mkenvimage tool.
Signed-off-by: Tiago Brusamarello <tiago.brusamarello@datacom.ind.br>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
cmarinas/boot-wrapper-aarch64.git does not exist any more.
Switch over to mark/boot-wrapper-aarch64.git.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Expose the Kconfig-related help commands when U-Boot uses the Kconfig
configuration. Like others (like Linux, barebox, busybox), only expose
menuconfig, not all the configurators.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Some U-Boot board configurations have CONFIG_FIT_SIGNATURE=y. In this
case, when U-Boot builds its tools, it requires OpenSSL support on the
host system.
Since we clearly don't want to unconditionally depend on host-openssl,
we introduce a new option to explicitly enable the dependency on
host-openssl. This is exactly identical to the existing
BR2_TARGET_UBOOT_NEEDS_DTC, for the dependency on host-dtc. It is
therefore the responsibility of the user to enable this option if his
board configuration uses CONFIG_FIT_SIGNATURE=y.
Necessary to fix bug #9316.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This unique NAME is used to construct a per br2-external tree variable,
BR2_EXTERNAL_$(NAME)_PATH, which contains the path to the br2-external
tree.
This variable is available both from Kconfig (set in the Kconfig
snippet) and from the .mk files.
Also, display the NAME and its path as a comment in the menuconfig.
This will ultimately allow us to support multiple br2-external trees at
once, with that NAME (and thus BR2_EXTERNAL_$(NAME)) uniquely defining
which br2-external tree is being used.
The obvious outcome is that BR2_EXTERNAL should now no longer be used to
refer to the files in the br2-external tree; that location is now known
from the BR2_EXTERNAL_$(NAME)_PATH variable instead. This means we no
longer need to expose, and must stop from from exposing BR2_EXTERNAL as
a Kconfig variable.
Finally, this also fixes a latent bug in the pkg-generic infra, where we
would so far always refer to BR2_EXTERNAL (even if not set) to filter
the names of packages (to decide whether they are a bootloader, a
toolchain or a simple package).
Note: since the variables in the Makefile and in Kconfig are named the
same, the one we computed early on in the Makefile will be overridden by
the one in .config when we have it. Thus, even though they are set to
the same raw value, the one from .config is quoted and, being included
later in the Makefile, will take precedence, so we just re-include the
generated Makefile fragment a third time before includeing the
br2-external's Makefiles. That's unfortunate, but there is no easy way
around that as we do want the two variables to be named the same in
Makefile and Kconfig (and we can't ask the user to un-quote that variable
himself either), hence this little dirty triple-inclusion trick.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Arnout Vandecappelle <arnout@mind.be>
Cc: Romain Naour <romain.naour@openwide.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
[Thomas:
- Rename the package from atfirmware to arm-trusted-firmware, in order
to match upstream.
- Remove option to apply custom patches. We no longer add such options,
and use the global patch directory instead.
- Rename the repo URL/version options, in order to not be Git specific,
in case support for fetching from other VCS is added later. This is
consistent with how other bootloaders handle this.
- Add license information.
- Do not add a weird dependency on the vexpress-firmware package in
Config.in. Instead, simply use it if it's available. Of course, some
configurations (such as the juno configuration) will fail to build if
vexpress-image is not enabled, but it's the responsibility of the
user to create a config that builds.
- Simplify misc aspects in the .mk file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit adds a new package for the SCP (System Control Processor)
firmware for the ARM reference platforms. There will most likely be
other SCP firmware provided by other vendors, but they might be provided
in a different form, so we for now create a vendor-specific package
named vexpress-firmware.
Since this firmware is used for booting, we create the package in boot/
and not in package/.
The package simply installs a single pre-built binary file into the
images directory.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
[Thomas:
- Rename the package from scpfirmware to vexpress-firmware.
- Add a Config.in prompt for the package.
- Remove the prompt-less Config.in options to select the Git repo and
version. Since we only support the Vexpress firmware, there's no need
for configurability here, so we just use the right Git repo/version
in the .mk file.
- Use $(INSTALL) -D to install the firmware file.
- Add license information.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
[Thomas: add hash file, as suggested by Yann.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Since commit fad58cefa4 ("boot/uboot: allow to build multiple U-Boot
images") the installation of SPL binary fails.
For example, when building the mx6cubox_defconfig target we see:
LD u-boot
OBJCOPY u-boot-nodtb.bin
COPY u-boot.bin
MKIMAGE u-boot.img
>>> uboot 2016.09.01 Installing to target
>>> uboot 2016.09.01 Installing to images directory
cp -dpf /home/fabio/buildroot/output/build/uboot-2016.09.01/u-boot.bin /home/fabio/buildroot/output/images/
cp -dpf /home/fabio/buildroot/output/build/uboot-2016.09.01/u-boot.img /home/fabio/buildroot/output/images/
cp -dpf /home/fabio/buildroot/output/build/uboot-2016.09.01/SPL /home/fabio/buildroot/output/images/
cp: cannot stat '/home/fabio/buildroot/output/build/uboot-2016.09.01/SPL': No such file or directory
Instead of calling 'make all' only for the BR2_TARGET_UBOOT_FORMAT_DTB_IMG
case, call 'make all' unconditionally so that the SPL target can also
be installed.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
With newer ARC toolchain obsolete -marcXXX were finally deperecated
and so compiler throws errors now about unknown option.
Solution is as simple as switching to more generic -mcu-XXX
options. Which we do. Unfortunately that change in upstream U-Boot [1]
happened right after v2016.09 was released an so we need to have that fix
for v2016.07 which is mentioned in axs10x defconfigs and for the latest
U-Boot release v2016.09 (which is selected by default if no defconfig is
used).
Once we deprecate either U-Boot version in U-Boot corresponding patch
should be removed essentially.
[1] http://git.denx.de/?p=u-boot.git;a=commit;h=7c8d81605302e7d7fdd3e7d8eb69302bddc64a2c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Thomas: handle the U-Boot bump to 2016.09.01.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
2016.09.01 is a bugfix release, so bump to this version.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Sometimes it is desired to build multiple U-boot images. E.g. one to
save into flash memory and one for serial load. So far this was not
possible.
This change allows to select any combination of the target formats. They
are all copied to the image folder.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
[Thomas:
- Handle the BR2_TARGET_UBOOT_FORMAT_BIN, which wasn't handled, and
therefore u-boot.bin was not copied when
BR2_TARGET_UBOOT_FORMAT_BIN=y.
- Rename UBOOT_BIN to UBOOT_BINS, since it can now contain multiple
values.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Ubuntu 16.10 has pie enable by default. This causes a build failure with
syslinux.
https://bugs.launchpad.net/ubuntu/+source/syslinux/+bug/1579023
Signed-off-by: Ryan Coe <bluemrp9@gmail.com>
[Thomas: improve patch description.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
grub2 assumes the strip command will generate output and the output should
always be stripped - so, just use the $(TARGET_CROSS)strip to make sure that
the build succeeds regardless of the buildroot strip configuration.
Signed-off-by: Charles Hardin <ckhardin@exablox.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit backports a patch from upstream grub2 that fixes a build
issue occuring at least with recent gcc versions:
gettext/gettext.c:37:36: error: storage size of 'main_context' isn't known
static struct grub_gettext_context main_context, secondary_context;
Fixes bug #8991.
Bug reproduced with:
BR2_x86_64=y
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_5=y
BR2_TOOLCHAIN_BUILDROOT_GLIBC=y
BR2_GCC_VERSION_6_X=y
BR2_TARGET_GRUB2=y
BR2_TARGET_GRUB2_X86_64_EFI=y
BR2_TARGET_GRUB2_BUILTIN_MODULES="boot linux ext2 fat squash4 part_msdos part_gpt normal efi_gop terminal"
and verified fixed after adding this patch.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This MBR routine is based on TS' original bootloader. It is loaded by
the bootrom stored in the companion FPGA, and chainloads an executable
located at the beginning of the first non-fs (0xda) partition.
Signed-off-by: Patrick Keroulas <patrick.keroulas@savoirfairelinux.com>
[Thomas:
- add hash file.
- install image in INSTALL_IMAGES_CMDS instead of
INSTALL_TARGET_CMDS.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
There was a typo in commit
b05ff12b6c ("uboot: install multiple spl
images"), leading to a missing closing parenthesis. This commit fixes
this typo.
Fixes bug #9086
Reported-by: Jebodiah Sensai <dkaplan65@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
For some platforms, there are multiple generated spl images. Extend
BR2_TARGET_UBOOT_SPL_NAME to allow these multiple images to be installed
after uboot build completes.
For example, the NextThingCo C.H.I.P. uses two binaries from uboot,
spl/sunxi-spl.bin and spl/sunxi-spl-with-ecc.bin.
Signed-off-by: Jason Abele <jason@nextthing.co>
[Maxime:
- Add foreach loop for general case and mkpimage
- Use firstword for zynq case]
Signe-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Since commit 0dca644e44 ("boot/uboot: fix
missing host-openssl for i.MX28 target"), we pass HOSTCFLAGS/HOSTLDFLAGS
in the environment of U-Boot when building. This is needed to allow
U-Boot to find the OpenSSL headers/libraries when they are
needed. Unfortunately, this breaks the build with old U-Boot versions as
the U-Boot Makefiles were not designed to have HOSTCFLAGS passed in,
which causes some important CFLAGS from the U-Boot build system to be
ignored.
As suggested by Arnout, we pass the HOST_CFLAGS inside HOSTCC directly,
which allows to pass the CFLAGS without overriding the internal U-Boot
CFLAGS.
Tested with an old U-Boot (2012.10), and a modern U-Boot in a
configuration that needs OpenSSL.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
There is no option --enable-liblzma=no in grub2's configure script, so
the only way to disable liblzma support is to pass
ac_cv_lib_lzma_lzma_code=no.
Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Tested-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
[Thomas: expand commit log, as suggested by Yann E. Morin.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
By default position independent executables (PIE) are generated
when building U-Boot elf target. MetaWare debugger doesn't support
PIE (position-independent executable).
In order to allow MDB load and run U-Boot elf, we need to do a
special trick, called "mdbtrick".
This special build target is used to fake generated U-Boot elf by:
1. Reset PIE flag in ELF header
2. Strip all debug information from elf
Signed-off-by: Zakharov Vlad <vzakhar@synopsys.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Arnout Vandecappelle <arnout@mind.be>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Thomas: don't use the helper.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Allow multiple file names to be listed in
BR2_TARGET_UBOOT_ENVIMAGE_SOURCE, concatenating them in the order
listed.
This allows the bulk of the environment to be shared across multiple
boards using a common environment file with board-specific values
supplied in a secondary environment source file.
Signed-off-by: Cam Hutchison <camh@xdna.net>
[Thomas: adjust indentation in the .mk file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is the first level bootloader for the Actions Semiconductor S500 SoC,
which is used on boards like Roseapple Pi and LeMaker Guitar.
The bootloader performs basic configuration and chain loads u-boot for
futher setup.
This bootloader is unfortunately only available as a binary blob. It gets
configured for a specific board using a binary (32bit x86) tool based on a
.ini file (somewhat similar to sunxi .fex).
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Building an U-Boot image for the i.MX23 or i.MX28 target requires to run the
bootloaders 'mxsimage' tool on the host. As mxsimage needs unconditionally
OpenSSL, building U-Boot for those targets fails if it is not available on
the host:
tools/mxsimage.c:18:25: fatal error: openssl/evp.h: No such file or directory
#include <openssl/evp.h>
Add the required dependency 'host-openssl' to all the different U-Boot image
types used to build a bootloader image for an i.MX23/i.MX28 target.
Also pass HOST_CFLAGS and HOST_LDFLAGS to the U-Boot build process so the right
-I/-L options will be used to find OpenSSL.
Ported from the Armadeus project:
https://sourceforge.net/p/armadeus/mailman/message/33595402/
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
[Jörg: port to recent Buildroot version]
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Barebox provides an option to embed a custom environment image into
barebox binary. This image will be used, when the environment found in
the environment sector is invalid. Both embedded and external images
can be used together, so having both options at the same time is
justified.
This patch sets barebox Kconfig option CONFIG_DEFAULT_ENVIRONMENT_PATH
to user specified path. This way one can use such BR's variables like
BR2_EXTERNAL, TOPDIR etc. to provide paths to custom environment
folders.
Cc: Pieter Smith <pieter@boesman.nl>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
u-boot-dtb.img only gets built by default (all target) if
CONFIG_OF_SEPARATE _AND_ CONFIG_SPL_FRAMEWORK are enabled.
Certain SoCs (E.G. Action Semi S500) use a proprietary first level
bootloader instead of u-boot SPL, but still use u-boot-dtb.img as the first
level bootloader parses the uImage header for size/loadaddr.
Ensure u-boot-dtb.img gets built if enabled by explicitly listing it as a
u-boot make target (next to all) to support such setups.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Syslinux uses the host version of gcc to build to bootloader. On systems
with gcc 5.3, this results in a bootloader that hangs. This issue has
been addressed in upstream syslinux, but an official release has not
been made yet. This commit adds the upstream patch to fix the issue.
Most likely fixes bug #8866.
Signed-off-by: Frank Hunleth <fhunleth@troodon-software.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Adds support to build barebox with an auxiliary config.
This is useful for building an SPL (Secondary Program Loader) in
addition to the traditional TPL (Tertiary Program Loader). The
Beaglebone Black for example has two barebox configurations:
- am335x_defconfig builds the full barebox bootloader with device
tree
- am335x_mlo_defconfig builds the smaller MLO bootloader that loads
the full barebox bootloader from the eMMC or SD card.
Tested with the following defconfig:
# architecture
BR2_arm=y
BR2_cortex_a8=y
BR2_ARM_EABIHF=y
# system
BR2_TARGET_GENERIC_HOSTNAME="beaglebone"
BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_DEVTMPFS=y
BR2_TARGET_GENERIC_REMOUNT_ROOTFS_RW=y
# filesystem
BR2_PACKAGE_AM33X_CM3=y
BR2_TARGET_ROOTFS_EXT2=y
BR2_TARGET_ROOTFS_EXT2_4=y
# bootloader
BR2_TARGET_BAREBOX=y
BR2_TARGET_BAREBOX_BOARD_DEFCONFIG="am335x"
BR2_TARGET_BAREBOX_IMAGE_FILE="images/barebox-am33xx-beaglebone.img"
BR2_TARGET_BAREBOX_CUSTOM_ENV=y
BR2_TARGET_BAREBOX_CUSTOM_ENV_PATH="board/beaglebone/barebox/barebox.env"
BR2_TARGET_BAREBOX_AUX=y
BR2_TARGET_BAREBOX_AUX_BOARD_DEFCONFIG="am335x_mlo"
BR2_TARGET_BAREBOX_AUX_IMAGE_FILE="images/barebox-am33xx-beaglebone-mlo.img"
# kernel
BR2_LINUX_KERNEL=y
BR2_LINUX_KERNEL_USE_DEFCONFIG=y
BR2_LINUX_KERNEL_DEFCONFIG="omap2plus"
BR2_LINUX_KERNEL_ZIMAGE=y
# use the barebox built-in dtb
# BR2_LINUX_KERNEL_DTS_SUPPORT is not set
Signed-off-by: Pieter Smith <pieter@boesman.nl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
No functional changes. In preparation for the auxiliary barebox build,
boot/barebox is split into two parts:
1. boot/barebox:
- The source and patch specification which are to be shared between the
barebox and barebox-aux packages.
- The barebox-package function and build logic.
2. boot/barebox/barebox:
- The package configuration, fragments, barebox env, etc.
- The actual barebox package make instantiation.
Signed-off-by: Pieter Smith <pieter@boesman.nl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
No functional changes: Extracts an argument to the inner-barebox-package
function to automatically determine the uppercase package name. This is needed
to support a 2nd config build. This results in the following renaming:
'BAREBOX' -> '$(1)'
All barebox packages are meant to be built from the same sources, so related
KConfig variables (origin, version and patch directory) are not extracted.
Signed-off-by: Pieter Smith <pieter@boesman.nl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
No functional changes: Introduces a barebox-package function towards
re-use by a 2nd config build.
Because the function is meant to be called from within a $(eval), all
instances of '$' has to be escaped. I.e. rename '$' -> '$$'.
Signed-off-by: Pieter Smith <pieter@boesman.nl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Support optional selection of the built image filename in a
multi-image barebox build. This makes it possible to specify which
image to pick in a multi-image barebox config such as the
am335x_defconfig.
Signed-off-by: Pieter Smith <pieter@boesman.nl>
[Thomas:
- remove default "", since this is the default for string options
- rename the prompt from "Barebox image filename" to "Image filename"
- slightly improve the Config.in help text.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This becomes handy when building hybrid images that needs to be able
to boot in MBR and GPT mode.
Signed-off-by: Benoît Allard <benoit.allard@greenbone.net>
Tested-by: Matt Weber <matt@thewebers.ws>
Reviewed-by: Matt Weber <matt@thewebers.ws>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
By default, the afboot-stm32 Makefile uses "CROSS_COMPILE =
arm-none-eabi-". Since I had such a toolchain installed on my system
when testing afboot-stm32, I didn't realize it wasn't using the
Buildroot toolchain.
However, using the Buildroot toolchain doesn't immediately works for
FLAT toolchains, as gcc automatically wants to create a FLAT
binary. So we need to adjust the afboot-stm32 Makefile to use directly
'ld' and not 'gcc' when linking.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Size growth is minimal and generally a non-issue for x86-based
platforms.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
[Thomas: add Altera in the option name and description, drop reference
to Go being needed and to Maxime Hadjinlian's version of mkpimage
since a C version is now used.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It's been deprecated for a year now so remove it.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
It doesn't hurt, and is useful for removable boot media like a pendrive
that may depend on usb enumeration and isn't available immediately.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
It doesn't hurt, and is useful for removable boot media like a pendrive
that may depend on usb enumeration and isn't available immediately.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This is a _very_ small bootloader for STM32 platforms.
At submission afboot-stm32 supports the following boards:
stm32429i-eval
stm32746g-eval
stm32f429i-disco
stm32f469i-disco
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Thomas: fix commit title, add dependency on BR2_arm.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Commit 16b8e813c8 removed all remaining users
of helper function insert_define.
Signed-off-by: Thomas De Schampheleire <thomas.de.schampheleire@gmail.com>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
make legal-info breaks when using an older u-boot version in local.mk
with OVERRIDE_SRCDIR, due to the reorganization of license files which
happened in u-boot v2013.10.
This issue had already been fixed in Buildroot for the regular use of
old u-boot versions (non-local.mk).
This patch adds the same fix to UBOOT_POST_RSYNC_HOOKS so that it also
covers the local.mk case.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fix improper use of qstrip; use correct variables.
Fixes#8546.
Reported-by: craigswank@gmail.com
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
[yann.morin.1998@free.fr: move the kconfig-package hunk to the
corresponding patch]
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Commit bf2bd11321 bumped U-Boot to version
2015.10 but forgot to update the hash as well.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
For a 64bit arm architecture, Buildroot uses arm64 terminology and
from the top-level Makefile KERNEL_ARCH is set to arm64 which is then
passed to the uboot build. This causes a compilation issue as uboot
uses the top-level system architecture as it's $(ARCH). So
arch/$(ARCH)/Makefile doesn't work with arm64 unless we adjust the
arch.
[Thomas:
- rewrap commit message text.
- simplify comment in the code.]
Signed-off-by: Ronak Desai <ronak.desai@rockwellcollins.com>
Signed-off-by: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Some U-Boot configurations require the Device Tree compiler to be
available, so we need to depend on host-dtc (example configuration:
zynq_zed).
However, we don't want to build it unconditionally, since the vast
majority of U-Boot configurations don't need it (and host-dtc itself
has a bunch of dependencies).
So, we simply add a Config.in option that allows users to indicate
whether their U-Boot needs DTC or not, and depend on host-dtc if this
option is enabled.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Fixes https://bugs.busybox.net/show_bug.cgi?id=8256
grub2's build system interprets CC, CFLAGS and CPPFLAGS as for the host
and uses TARGET_CC etc. for the target. However, NM, OBJCOPY and STRIP
are used for the target. We currently pass the host-versions of these
tools as part of $(HOST_CONFIGURE_OPTS).
While we're at it, also pass TARGET_LDFLAGS.
This problem had not been noticed up to now because usually we build on
an x86 machine for the x86 architecture, so the binutils are compatible.
However, this is not true on an i386 when building for x86_64.
Cc: Christophe Bricout <christophebricout@yahoo.fr>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Due to recent changes in U-Boot, see
http://git.denx.de/?p=u-boot.git;a=commit;h=a26cd04920dc069fd6e91abb785426cf6c29f45f
re-creation of .config from defconfig by "make oldconfig" happened
incorrectly.
Default prompt for target selection was set as No that lead to missing platform
selection by automated scripts like that:
------------------>8------------------
"yes "" | make oldconfig" on defconfig
------------------>8------------------
And that lead to build failure:
------------------>8------------------
$ make
scripts/kconfig/conf --silentoldconfig Kconfig
CHK include/config.h
UPD include/config.h
GEN include/autoconf.mk
In file included from ./include/common.h:18:0:
include/config.h:5:22: fatal error: configs/.h: No such file or directory
#include <configs/.h>
^
compilation terminated.
scripts/Makefile.autoconf:72: recipe for target 'include/autoconf.mk' failed
make[1]: *** [include/autoconf.mk] Error 1
------------------>8------------------
This patch reverts mentioned change making possible to build U-Boot
2015.07 in Buildroot.
Note there's a probability that this particular patch won't make its way
in upstream U-Boot and better solution will be found there. But for now
we need to fix U-Boot building in Buildroot anyways.
Hopefully for the next release this patch won't be necessary.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Building Grub2 El Torito for i386 EFI errors complaining it cannot
find cdboot.img
cdboot.img: No such file or directory
This commit builds El Torito for i386 PC only.
[Thomas: fix installation ordering.]
Signed-off-by: Ray Kinsella <ray.kinsella@intel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It's rather unclear that uboot.sb, uboot.sd and uboot.nand are
Freescale i.MX28 specific, so let's make that clear in the prompt of
each option, like we do for the Marvell-specific uboot.kwb.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
With the patchset "kconfig: turnaround into single .config"
[http://lists.denx.de/pipermail/u-boot/2015-February/205490.html]
U-Boot switched to a single .config file for board configuration. This
allows us to use the kconfig-package infrastructure.
For providing backward compatibility with older U-Boot version a user
choice between the new Kconfig and the legacy build system is
introduced.
[Thomas:
- make use of the legacy build system the default, to not break
existing configurations.
- add some comments in the code checking all the configuration
options, in order to hopefully make it a bit clearer.]
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit integrates generation of a bootable image
for Xilinx Zynq. The generation is independent on Xilinx
flow and utilizes the host-zynq-boot-bin package. The only
required step is to generate a proper U-Boot SPL (instead
of the FSBL).
The SPL generation might work when providing the working
ps7_init.c file to U-Boot. However, from U-Boot 2015.07
a set of generic ps7_init.c files is included and used to
build the U-Boot SPL for various boards. The ps7_init.c file
has been released under GNU/GPL license for this purpose.
For details, see
http://lists.denx.de/pipermail/u-boot/2015-April/210664.html
The SPL searchs for u-boot-dtb.img when booting so we
enforce using of the BR2_TARGET_UBOOT_FORMAT_DTB_IMG format.
[Thomas: remove select of BR2_PACKAGE_HOST_ZYNQ_BOOT_BIN, since this
option no longer exists.]
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Allow to generate u-boot-dtb.img. This is the same format
as u-boot.img, however, it contains a built-in device-tree.
This file is being loaded by the U-Boot SPL.
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
If we check that the user provides a config file after we call to the
kconfig-package infra, the error message we get is the one for the
kconfig-package infra, not the custom error message we want to show to
the user.
So, only call kconfig-package after we do the check.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
If we check that the user provides a config file after we call to the
kconfig-package infra, the error message we get is the one for the
kconfig-package infra, not the custom error message we want to show to
the user.
So, only call kconfig-package after we do the check.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Allow to generate 'u-boot.nand', Freescale i.MX28 BootStream format (.sb)
with a header for booting from NAND flash.
There are two possibilities when preparing an image writable to NAND flash:
1) The NAND was not written at all yet or the BCB (Boot Control Blocks) is
broken. In this case, the NAND image 'u-boot.nand' needs to written.
2) The NAND flash was already written with a good BCB. This applies after
'u-boot.nand' was correctly written. There is no need to write the BCB
again. In this case, the bootloader can be upgraded by writing 'u-boot.sb'.
To satisfy both cases 'u-boot.nand' as well as the make target 'u-boot.sb' are
copied to the binaries directory.
mxsboot for NAND images needs all three parameters typed in as integer values
(hex values do not work). The default values choosen are typical sizes for a
NAND flash.
For more information see:
http://www.denx-cs.de/doku/?q=m28evkrunuboot
Commit Note: This patch is based on top of
"[PATCH v2 1/2] boot/uboot: add support for i.MX28 SD format"
http://patchwork.ozlabs.org/patch/453116/
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch adds the option to download at91bootstrap3 from
a custom git URL. This is a requirement for all that boards
that use a custom at91bootstrap3 version.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch bumps at91bootstrap3 version to 3.7.2
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch adds licensing informations to at91bootstrap3
[Thomas:
- change from "BSD-2c with endorsement clause" to "Atmel License",
because the license of AT91Bootstrap is neither a BSD-2c nor a
BSD-3c: it does not carry the second clause of the BSD-2c or BSD-3c
licenses giving the condition of redistribution of the binary form.]
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
In order to support ISO9660 bootable images that rely on Grub 2, this
commit modifies thr Grub 2 makefile to generate and install an El
Torito image. Such an image is simply produced by concatenating the
cdboot.img provided by Grub 2, and the Grub 2 image generated by
Buildroot using grub-mkimage.
Since this action is so simple and cost-free, we don't bother adding a
Grub 2 sub-option for that, and simply generate the El Torito image
unconditionally.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
It's been deprecated since the 2014.05 release, so a year has passed.
Add legacy info as well to raise a warning when it's used.
[Peter: Remove entire config.h fixup handling]
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As we recently did for U-Boot, disable checking hashes for custom
versions of barebox.
Note that we currently have no hash file for barebox, but avoiding the
check will already be in place when we do add it.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
For custom tarballs, it's quite obvious we can not check hashes.
For custom versions, that's not so obvious. One might think we could
have hashes for all the official releases, but that's not possible: if
the user uses a released version of Buildroot (say 2015.05) much later
in the future, and wants to use the then-released 2038.02 U-Boot. It now
seems pretty obvious that Buildroot 2015.02 can't know the hash for
U-Boot 2038.02.
So, disable checking the hash for custom tarballs and custom versions.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Vincent Stehle <vincent.stehle@laposte.net>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The git:// protocol may not go through conservative corporate firewalls.
Use http, that goes out through about anything.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Instead of manually testing MAKECMDGOALS, use the newly introduced
BR_BUILDING variable to know if we're building or not.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Tested-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Users should use BR2_TARGET_UBOOT_PATCH instead.
Signed-off-by: Frank Hunleth <fhunleth@troodon-software.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The existing u-boot patch option only allowed directories to be
specified. This adds support for URLs using similar code as found
in linux/linux.mk. Local files are also handled now.
This change is useful for Intel Edison support, so that Intel's u-boot
patch can be downloaded rather than stored in the Buildroot source tree.
Signed-off-by: Frank Hunleth <fhunleth@troodon-software.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Thomas: fix issues noticed by Arnout:
- Rewrap the linux/Config.in paragraph
- Revert the "is a toolchain dependency" -> "has a toolchain
dependency" change from pkg-generic.mk, as the original was
correct.]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
For some (silly?) reason, the kconfig-package infra always wants
<pkg>_KCONFIG_FILE to be defined. So let's do like barebox does: use a
temporary AT91BOOTSTRAP3_SOURCE_CONFIG variable, and assign it to
AT91BOOTSTRAP3_KCONFIG_FILE. This way, the latter is always defined,
even if to the empty value.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
In at91bootstrap3, defconfig files are spread out in various
sub-directories, so we can't easily construct the path to those
defconfig files.
As it turns out, there are no two defconfig files named the same; they
all contain at least the board name, plus some extra info. And there is
always only one directory depth below board/ where all defconfig files
are to be found.
Also, at91bootstrap3's own Makefile relies on this single-match as it
runs a 'find' command to locate the defconfig file.
So, even though we do not know the path to the defconfig file, we can
construct a shell-glob quite easily (in the hope that there will never
be more than one directory depth).
Signed-off-by: Mauro Condarelli <mc5686@mclink.it>
[yann.morin.1998@free.fr:
- remove custom _CONFIGURE_CMDS, handled by pkg-kconfig (Thomas)
- remove redundant intermediate variable
- fix using internal defconfig files
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Thomas De Schampheleire <patrickdepinguin@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Several packages have some logic to apply custom patches that existed
before the BR2_GLOBAL_PATCH_DIR mechanism: at91bootstrap,
at91bootstrap3, barebox, uboot and linux. Currently, the logic of
those packages to apply custom patches is to match
<package-name>-*.patch, which is not consistent with what we've done
for patches stored in the package directory, and for patches stored in
BR2_GLOBAL_PATCH_DIR: in such cases, we simply apply *.patch.
Therefore, for consistency reasons, this commit changes these packages
to also apply *.patch.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Allow to generate u-boot.sd, Freescale i.MX28 SB format with a header for
booting from an SD card.
U-boot includes an mxsboot tool to generate this format, starting from
v2011.12.
See u-boot doc/README.mxs (or doc/README.mx28_common before 2013.07).
[Arnout:
- Wrap Config.in help text at 72 columns.
- Remove v from U-Boot version specifier.
- Refer to different README name before 2013.07.
- Depend on host-elftosb
- Add comment to clarify sb -> sd conversion.]
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Reviewed-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Drop the buildroot toolchain non-largefile support option since it's
being removed.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit doesn't touch infra packages.
Signed-off-by: Jerzy Grzegorek <jerzy.grzegorek@trzebnica.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Since 6.03 syslinux release, the gnu-efi sources are bundled whith
syslinux. We need to force the build system to use the Buildroot's
gnu-efi package.
Remove the patch for find-gnu-efi.sh script which was removed, as well
as the SYSROOT variable from the BUILD_CMDS, which is no longer
needed.
There are still some parallel build issues, so MAKE1 can't
be removed for now.
Add a hash file.
Fix indentation.
[Thomas: fix minor typos in a new comment in the .mk file.]
Signed-off-by: Romain Naour <romain.naour@openwide.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Barebox uses KERNEL_ARCH to derive BAREBOX_ARCH, but doesn't
currently handle the case of the x86-64 architecture. In this
case KERNEL_ARCH is x86_64, but BAREBOX_ARCH should be x86
nonetheless.
Signed-off-by: Fabien Lahoudere <fabienlahoudere.pro@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
