Some U-Boot configurations use lzop, which may not be available on the
build machine since it's not a mandatory dependency of Buildroot.
To solve this, a new option BR2_TARGET_UBOOT_NEEDS_LZOP is introduced,
and handled in a similar way to the existing
BR2_TARGET_UBOOT_NEEDS_OPENSSL option.
This fixes the build of the dra7xx_evm U-Boot defconfig as of U-Boot
2018.07, on a build machine without lzop installed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
U-Boot SPL configures pinmuxes, clocks and other low-level devices. On
the Xilinx ZynqMP SoCs the code to do this resides in a file called
psu_init_gpl.c which is initially generated by the Xilinx development
tools. Add an option to pass these files from the outside (e.g. in the
board files).
For this to work properly, a patch to U-Boot is needed. However this
patch must be applied by each defconfig using
BR2_TARGET_UBOOT_ZYNQMP_PSU_INIT_DIR. If it were in boot/uboot/ to be
applied unconditionally, it would break the build for configs using a
U-Boot version where the patch is already applied.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Reviewed-by: Joel Carlson <JoelsonCarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
[Thomas: add comment about U-Boot version requirements to use this
option.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
In order to boot on the Xilinx ZynqMP SoCs, U-Boot SPL requires a
recent PMU firmware loaded. Instruct U-Boot to add pmufw.bin to the
boot.bin file together with U-Boot SPL, and the boot ROM will load
both.
For this to work properly, a patch to U-Boot is needed. However this
patch must be applied by each defconfig that wishes to use
BR2_TARGET_UBOOT_ZYNQMP_PMUFW. If it were in boot/uboot/ to be applied
unconditionally, it would break the build for configs using a U-Boot
version higher than 2018.7-rc1 where the patch is already applied.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Joel Carlson <joelsoncarl@gmail.com>
Reviewed-by: Joel Carlson <JoelsonCarl@gmail.com>
Tested-by: Joel Carlson <JoelsonCarl@gmail.com>
[Thomas:
- indicate that this feature requires U-Boot 2018.07, since commit
c7df098a71e05dc81cee818747759e8060b59626 is needed.
- define UBOOT_ZYNQMP_KCONFIG_PMUFW only once, and instead use a
variable named UBOOT_ZYNQMP_PMUFW_PATH to store the path to the PMU
firmware]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Some i.MX boards which use device tree to describe the hardware
for U-Boot generate a u-boot-dtb.imx binary.
Introduce the BR2_TARGET_UBOOT_FORMAT_DTB_IMX option to
handle such case.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
By default, the builsystem for uboot defaults to 'legacy', while the
default version is very well capable of using the 'kconfig' buildsystem
instead.
Having the 'legacy' buildsystem be the default in that case makes it
quite inconvenient for users: they would expect to be able to use e.g.
uboot-menuconfig et al. with the default uboot version.
Switch to using 'kconfig' when we use the latest version. Keep the
'legacy' as default for everything else.
Also, invert the 'legacy' and 'kconfig' entries in the choice: it is
nicer to have the recent and future-proof entry first.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Tested-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
... to follow the convention: type, default, depends on, select, help.
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Some ARM64 platforms (such as Allwinner A64/H5) have a boot process
where U-Boot encapsulates the BL31 part of the ARM trusted
firmware. For such platforms, we need to build ATF before U-Boot, and
pass a BL31 variable pointing to ATF bl31.bin to the U-Boot build
process.
This commit introduces a BR2_TARGET_UBOOT_NEEDS_ATF_BL31 variable to
achieve this.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas:
- Rename option to BR2_TARGET_UBOOT_NEEDS_ATF_BL31
- Drop changes to arm-trusted-firmware.mk, they are taken care of by
previous commits.
- Improve Config.in help text
- Add missing dependency on arm-trusted-firmware when
BR2_TARGET_UBOOT_NEEDS_ATF_BL31 is enabled.
- Use bl31.bin from $(BINARIES_DIR) instead of taking it from ATF's
build dir.]
[Peter: depend on toplevel atf option and select bl31 option. Ensure it
cannot be enabled together with ARM_TRUSTED_FIRMWARE_UBOOT_AS_BL33
as that would cause circular dependencies]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Since the BR2_TARGET_UBOOT_SPL_NAME option accepts a space-separated
list of binaries, the same option can be reuses for TPL binaries as
well. This commit updates the string and help text to indicate that
the same option can be used for SPL and TPL.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
U-Boot nowadays also uses kconfig, so we can handle config fragments like we
do for barebox/busybox/linux.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add a new config option BR2_TARGET_UBOOT_NEEDS_PYLIBFDT for U-Boot
targets, like sunxi, needing the Python libfdt library.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
[Thomas: drop bogus selects on BR2_PACKAGE_HOST_{PYTHON,SWIG}.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
More and more of our defconfigs need to generate a U-Boot boot
script. It's a simple call to mkimage, but we already have 12
instances of this logic in board/, and there are patch series waiting
in patchwork adding 3 more boards that need this.
So let's add an option in the U-Boot package to generate such a boot
script image easily.
Note that we assume a single script needs to be generated, and the
output file name is boot.scr. The only platform for which it seems to
not be the case are the Boundary Devices platforms: they generate two
boot scripts, 6x_bootscript and 6x_upgrade, but they are anyway
installed inside TARGET_DIR, not BINARIES_DIR.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Similaly to Linux, this patch adds the ability to copy in and build
out-of-source device tree sources during a U-Boot build.
Signed-off-by: James Balean <james@balean.com.au>
Cc: Arnout Vandecappelle <arnout@mind.be>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
SPL is the name used for spl on i.MX6, so update the same on
BR2_TARGET_UBOOT_SPL_NAME help text.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas: rewrap Config.in help text.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
On older SoCFPGA SoCs, there was not enough SRAM to fit the entire
U-Boot, so a SPL model was used. The SPL was therefore the binary that
had to be "prepared" to be loaded by the ROM code using the mkpimage
tool.
With newer SoCFPGA SoCs, there is enough SRAM to fit the entire U-Boot,
and therefore the ROM code directly loads U-Boot. In this case, it's the
real U-Boot image (not the SPL) that needs to be prepared using
mkpimage.
This code adds support for the newer SoCFPGA SoCs, by adjusting the
mkpimage related logic to apply on the SPL if an SPL is enabled, or on
the full U-Boot image otherwise.
Signed-off-by: Lionel Flandrin <lionel@svkt.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Commit 3e3fef39e7 added new and improved
patch handling, with BR2_TARGET_UBOOT_PATCH. This was in addition to
the existing BR2_TARGET_UBOOT_CUSTOM_PATCH_DIR option, that only
handled directories.
Later, commit 21b25d28fc moved the old
BR2_TARGET_UBOOT_CUSTOM_PATCH_DIR to legacy options. But on the way,
bad things happened:
* The original option was a string, while the one added to Config.in.legacy
is a bool. This results in a warning from defconfigs that actually define
the old BR2_TARGET_UBOOT_CUSTOM_PATCH_DIR (because a string is not a valid
value for a bool), but it does not result in the legacy option being
selected. Consequently, BR2_LEGACY is not selected either.
* The advice at the top of Config.in.legacy to add a hidden WRAP option
to select BR2_LEGACY was not heeded.
* The advice at the top of Config.in.legacy to use the old string
option as the default for the new string option was not heeded. In
this case, the variable was not just renamed, as the old option
supported directories only, while the new one supports files too.
But since the old option is a subset of the new option, it can still
be used to set a useful default.
So, this mod turns the legacy option back to a string, adds a hidden
bool WRAP option to set BR2_LEGACY when the string is non emoty, and
uses the legacy option to set the default for the new option.
Signed-off-by: Danomi Manchego <danomimanchego123@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Some U-Boot board configurations have CONFIG_FIT_SIGNATURE=y. In this
case, when U-Boot builds its tools, it requires OpenSSL support on the
host system.
Since we clearly don't want to unconditionally depend on host-openssl,
we introduce a new option to explicitly enable the dependency on
host-openssl. This is exactly identical to the existing
BR2_TARGET_UBOOT_NEEDS_DTC, for the dependency on host-dtc. It is
therefore the responsibility of the user to enable this option if his
board configuration uses CONFIG_FIT_SIGNATURE=y.
Necessary to fix bug #9316.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
2016.09.01 is a bugfix release, so bump to this version.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Sometimes it is desired to build multiple U-boot images. E.g. one to
save into flash memory and one for serial load. So far this was not
possible.
This change allows to select any combination of the target formats. They
are all copied to the image folder.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
[Thomas:
- Handle the BR2_TARGET_UBOOT_FORMAT_BIN, which wasn't handled, and
therefore u-boot.bin was not copied when
BR2_TARGET_UBOOT_FORMAT_BIN=y.
- Rename UBOOT_BIN to UBOOT_BINS, since it can now contain multiple
values.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
For some platforms, there are multiple generated spl images. Extend
BR2_TARGET_UBOOT_SPL_NAME to allow these multiple images to be installed
after uboot build completes.
For example, the NextThingCo C.H.I.P. uses two binaries from uboot,
spl/sunxi-spl.bin and spl/sunxi-spl-with-ecc.bin.
Signed-off-by: Jason Abele <jason@nextthing.co>
[Maxime:
- Add foreach loop for general case and mkpimage
- Use firstword for zynq case]
Signe-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Allow multiple file names to be listed in
BR2_TARGET_UBOOT_ENVIMAGE_SOURCE, concatenating them in the order
listed.
This allows the bulk of the environment to be shared across multiple
boards using a common environment file with board-specific values
supplied in a secondary environment source file.
Signed-off-by: Cam Hutchison <camh@xdna.net>
[Thomas: adjust indentation in the .mk file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
[Thomas: add Altera in the option name and description, drop reference
to Go being needed and to Maxime Hadjinlian's version of mkpimage
since a C version is now used.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It's been deprecated for a year now so remove it.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Some U-Boot configurations require the Device Tree compiler to be
available, so we need to depend on host-dtc (example configuration:
zynq_zed).
However, we don't want to build it unconditionally, since the vast
majority of U-Boot configurations don't need it (and host-dtc itself
has a bunch of dependencies).
So, we simply add a Config.in option that allows users to indicate
whether their U-Boot needs DTC or not, and depend on host-dtc if this
option is enabled.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
It's rather unclear that uboot.sb, uboot.sd and uboot.nand are
Freescale i.MX28 specific, so let's make that clear in the prompt of
each option, like we do for the Marvell-specific uboot.kwb.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
With the patchset "kconfig: turnaround into single .config"
[http://lists.denx.de/pipermail/u-boot/2015-February/205490.html]
U-Boot switched to a single .config file for board configuration. This
allows us to use the kconfig-package infrastructure.
For providing backward compatibility with older U-Boot version a user
choice between the new Kconfig and the legacy build system is
introduced.
[Thomas:
- make use of the legacy build system the default, to not break
existing configurations.
- add some comments in the code checking all the configuration
options, in order to hopefully make it a bit clearer.]
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit integrates generation of a bootable image
for Xilinx Zynq. The generation is independent on Xilinx
flow and utilizes the host-zynq-boot-bin package. The only
required step is to generate a proper U-Boot SPL (instead
of the FSBL).
The SPL generation might work when providing the working
ps7_init.c file to U-Boot. However, from U-Boot 2015.07
a set of generic ps7_init.c files is included and used to
build the U-Boot SPL for various boards. The ps7_init.c file
has been released under GNU/GPL license for this purpose.
For details, see
http://lists.denx.de/pipermail/u-boot/2015-April/210664.html
The SPL searchs for u-boot-dtb.img when booting so we
enforce using of the BR2_TARGET_UBOOT_FORMAT_DTB_IMG format.
[Thomas: remove select of BR2_PACKAGE_HOST_ZYNQ_BOOT_BIN, since this
option no longer exists.]
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
