In new kernels sunxi-mmc driver has been switched to asynchronous probe.
As a result, mmc (SD/eMMC) indexes can be shuffled breaking board boot.
Switch to GPT partitions to use partition labels instead of explicit
mmcblk device names. Note that the default GPT partition table location
conflicts with the SPL location, so move GPT table after bootloaders.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Bump U-Boot and Linux kernel versions. Updating U-Boot to 2021.04
requires the following two changes.
First, after switching to binman, u-boot.itb is no more generated for
64-bit sunxi boards. Combined u-boot-sunxi-with-spl.bin image should
be used instead. This image contains SPL, U-Boot, and FIT image,
where FIT image contains other binaries such as BL31 and SCP.
Second, new U-Boot enables support for System Control Processor (SCP)
firmware. SCP firmware is included by default into FIT image in the
combined u-boot-sunxi-with-spl.bin binary. When SCP is not available
or not needed, it should be explicitly disabled by pointing to an
empty file. Support for Allwinner SCP firmware is not yet available
neither in Buildroot nor in mainline kernel. So disable it for now
using custom U-Boot build options.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
In commit 38d04e6b13, I did a last-minute change by adding the comment
to explain where the PARTLABEL was coming from, and introduced a typo in
that comment.
Fix it.
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Patch that pins mmc indexes was not accepted to mainline kernel. Drop that
patch and switch to GPT to use partition labels. For GPT the name of the
partition in genimage.cfg is used as the label for that partition. Note
that the default GPT partition table location conflicts with the SPL
location, so move GPT table after bootloaders.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Bump Linux to 5.10.10 and U-Boot to 2020.10. In the new kernel sunxi-mmc
driver has been switched to asynchronous probe. As a result, mmc indexes
can be shuffled breaking board boot. Add patch that pins mmc indexes to
their original ordered values.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
GPT provides partition labels, which can be used to tell the kernel to find
the rootfs based on it (root=PARTLABEL=rootfs) as a nicer/more extensible
solution than the MBR disk signature / PARTUUID.
When using GPT, the name of the partition in genimage.cfg is used as the
label for that partition.
The default GPT partition table location unfortunately conflicts with the
SPL location, so move the 16KB GPT table after it.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
[yann.morin.1998@free.fr: add the comment about 'rootfs']
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The probing order of the two mmc controllers (sdcard and sdio wifi) has
changed in kernel 5.10 since commit 21b2cec61c04bd1 (mmc: Set
PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4), so change to
root=PARTUUID=.. instead of hardcoding /dev/mmcblkXp2.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
[yann.morin.1998@free.fr: use feedc0de as magic]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
HDMI support is enabled by default in sunxi_defconfig since commit
c822a3ec17 (ARM: configs: sunxi: Add DRM output-related options), so drop
from fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Orangepi Zero Plus board:
- U-Boot 2020.10
- Linux 5.7.19
- Default packages from buildroot
This patch is based on Orangepi Zero Plus2 board support, so genimage
configuration and description is copy pasted. One difference is that
newer Linux and U-Boot are selected. Another difference is Ethernet
support (Plus) instead of WiFi (Plus2).
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Analog audio is enabled by default in sunxi_defconfig since commit 5d2408c6
(ARM: configs: sunxi: Add sun8i analog codec), so drop from fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Very similar to orangepi-zero, except that the board has a 16MB SPI flash, a
2nd ethernet port is provided through a Realtek RTL8152 and wifi is provided
through a Realtek RTL8189FTV (no mainline driver, not supported).
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Orangepi lite2 board has AP6356S WiFi/BT combo, but does
not have ethernet port. So it makes sense to enable wireless
networking by default:
- add broadcom wireless firmware package to image
- add basic wireless tools to image
- add rootfs overlay with proper NVRAM file for on-board AP6356S chip
- add mdev to image to enable module autoloading
- update readme.txt to test wifi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Orangepi Lite2 board with below features:
- U-Boot 2018.09
- Linux 4.19.0-rc8
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Orangepi One Plus board with below features:
- U-Boot 2018.09
- Linux 4.19.0-rc8
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
4.18 brought cpufreq support for H3, but sunxi_defconfig does not enable the
ondemand cpufreq govenor so the frequency is dynamically adjusted - So
enable it in linux-extra.config.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
4.18 brought cpufreq support for H3, but sunxi_defconfig does not enable the
driver for the sy8106a regulator used on the board or enable the ondemand
cpufreq govenor so the frequency is dynamically adjusted - So enable these in
linux.fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
4.17 brings support for HDMI out, but sunxi_defconfig hasn't been updated to
enable the drivers - So add a kernel fragment to enable them.
Likewise, analog audio has been supported since 4.10, but the driver isn't
enabled in sunxi_defconfig, so enable it in the fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump linux as well headers to v4.16 version, this eventually drop the
wifi patch since it has been merged to Linux v4.16.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Orange-Pi Zero Plus2 board has AP6212 WiFi/BT combo, but does
not have ethernet port. So it makes sense to enable wireless
networking by default:
- add DTS patch enabling AP6212 WiFi/BT combo support
-- this patch is on its way to mainline Linux v4.16
- enable WiFi support in kernel config
- enable Broadcom brcmfmac kernel driver in kernel config
- add Broadcom wireless firmware package to image
- add basic wireless tools to image
- add mdev to image to enable module autoloading
- add rootfs overlay with proper NVRAM file for on-board AP6212 chip
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump versions:
- use U-Boot 2008.01
- use Linux kernel v4.15.2
Drop patch with dts sdcard fix since it has been
merged to Linux v4.15.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently in Orange Pi boards post-build script is used only to generate
U-Boot boot script and post-image script is used only to generate sdcard
image according to genimage configuration. However both those tasks can
now be handled by generic Buildroot tools:
- BR2_TARGET_UBOOT_BOOT_SCRIPT config options
- support/scripts/genimage.sh script
This patch drops custom scripts replacing them
by generic Buildroot tools.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Orangepi PC2
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Zero Plus2
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Prime
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Orangepi Win/Win Plus
board with below features:
- U-Boot 2017.11
- Linux 4.14
- Default packages from buildroot
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This board is quite similar to orangepi-one board. Instead of ethernet, it
has RTL8189FTV SDIO WiFi chip.
Board support package includes the following components:
- mainline u-boot 2017.09
- mainline kernel 4.13.11
Signed-off-by: Jan Kraval <jan.kraval@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This board is a variant of orangepi-pc board. It adds 8GB eMMC and Realtek
RTL8189FTV SDIO WiFi chip. This variant has a separate support in U-Boot
and kernel. So it makes sense to create a separate entry
for this board in buildroot.
Board support package includes the following components:
- mainline u-boot 2017.09
- mainline kernel 4.13.11
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
[Thomas: add entry to DEVELOPERS file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Since things are no longer installed in $(HOST_DIR)/usr, the callers
should also not refer to it.
This is a mechanical change with
git grep -l 'HOST_DIR}\?/usr/' board | xargs sed -i 's%\(HOST_DIR}\?\)/usr/%\1/%g'
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Chakra Divi <chakra@openedev.com>
[Thomas: remove host-uboot-tools from defconfig, already pulled by
BR2_TARGET_UBOOT_BOOT_SCRIPT, remove trailing whitespace.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch adds basic support for orangepi-zero board.
Board support package includes the following components:
- mainline kernel v4.11
- mainline u-boot v2017.03
- extra kernel config options: spidev, spi nor flash, wifi
- dts patches to enable SPI NOR and spidev
More details about this board are available here:
- http://linux-sunxi.org/Orange_Pi_Zero
Note that at the moment networking is not supported right out of the box.
Ethernet submission to mainline kernel is a work in progress, see the
latest dwmac-sun8i branches at https://github.com/montjoie/linux
On-board SDIO WiFi chip XR819 is supported by off-the-tree wireless
driver available at https://github.com/fifteenhex/xradio
Changes from v1:
* Send patch using proper subject
* Update xr819 kernel dts patch: add compatible property
[Peter: fix s/PC/Zero/ typo]
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The orangepi board variants use identical post-build and post-image scripts,
so move them up to board/orangepi and add symlinks in the variant
subdirectories, similary to how we handle it for the raspberry pi variants.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Board support package includes the following components:
- mainline u-boot 2016.09.01
- mainline kernel 4.9
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Rename orangepipc files, configs, and directories:
- oragepipc_defconfig -> orangepi_pc_defconfig
- board/orangepi/orangepipc -> board/orangepi/orangepi-pc
The purpose of the patch is to improve readability before
adding other boards of orangepi family.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
There's now an sun8i-h3-orangepi-pc dts, so we can use that and drop the
hack in the post-image script.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As described by http://linux-sunxi.org/Bootable_SD_card#SD_Card_Layout
The space betweem 544KB..1MB is reserved / used for the u-boot environment,
so mark it as such to make sure genimage doesn't put other partitions here.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
[Peter: use tarball for Linux kernel, use 4.4 kernel headers]
Signed-off-by: Eelco Chaudron <echaudron@xiot.nl>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit adds a configuration for the Orange Pi PC board,
<http://www.orangepi.org/orangepipc/>.
Signed-off-by: Eelco Chaudron <echaudron@xiot.nl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
