virtio-fs allow sharing a directory between the host and the guest.
It require virtiofsd daemon running before starting Qemu.
The wiki [1] recommand to enable the following kernel options:
CONFIG_VIRTIO
CONFIG_VIRTIO_FS
CONFIG_DAX
CONFIG_FS_DAX
CONFIG_DAX_DRIVER
CONFIG_ZONE_DEVICE
But virtio-fs works fine with only VIRTIO_FS.
Note: ZONE_DEVICE can only be enabled on aarch64 since kernel >= 5.7.
ARCH_ENABLE_MEMORY_HOTREMOVE support is missing for previous kernel [2].
[1] https://virtio-fs.gitlab.io/howto-qemu.html
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=bbd6ec605c0fc286c3f8ce60b4ed44635361d58b
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
>From [1]:
This kernel option allow exporting of the QEMU firmware configuration (fw_cfg)
file entries via sysfs. Entries are found under /sys/firmware/fw_cfg when this
option is enabled and loaded.
Enable the suboption to allow the qemu_fw_cfg device to be initialized via the
kernel command line or using a module parameter.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/drivers/firmware/Kconfig?h=v5.4.42#n187
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This driver is intended to be used by mesa virgl Gallium on the guest.
virtio-gpu is enabled by adding "-device virtio-gpu-pci" on the qemu
command line.
It's detected by lspci and dmesg log:
$ lspci
00:01.0 Display controller: Red Hat, Inc. Virtio GPU (rev 01)
$ dmesg
virtio-pci 0000:00:01.0: enabling device (0000 -> 0002)
[drm] pci: virtio-gpu-pci detected at 0000:00:01.0
[drm] virgl 3d acceleration not supported by host
[drm] EDID support available.
[TTM] Zone kernel: Available graphics memory: 51876 KiB
[TTM] Initializing pool allocator
[TTM] Initializing DMA pool allocator
[drm] number of scanouts: 1
[drm] number of cap sets: 0
[drm] Initialized virtio_gpu 0.1.0 0 for virtio2 on minor 0
The framebuffer interface fb0 is now present in /dev
$ ls /dev/fb*
/dev/fb0
See:
https://www.kraxel.org/blog/2019/09/display-devices-in-qemu/https://at.projects.genivi.org/wiki/display/WIK4/GENIVI+Technical+Summit+Session+Content+2018?preview=%2F28412356%2F28412481%2F2018-10-11_GeniviBangalorTechSummit_Virtio_GPU.pdf
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add the CONFIG_PCI symbol due a change in kernel 5.0 [1].
The option was previously enabled by default (default y).
"PCI: consolidate PCI config entry in drivers/pci
There is no good reason to duplicate the PCI menu in every architecture.
Instead provide a selectable HAVE_PCI symbol that indicates availability
of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the
rest in drivers/pci."
Qemu aarch64 provide a PCIe Host bridge but it require CONFIG_PCI_HOST_GENERIC
enabled in the kernel.
With CONFIG_PCI_HOST_GENERIC enabled PCIe host bridge is detected:
$ dmesg
pci-host-generic 4010000000.pcie: host bridge /pcie@10000000 ranges:
pci-host-generic 4010000000.pcie: IO 0x3eff0000..0x3effffff -> 0x00000000
pci-host-generic 4010000000.pcie: MEM 0x10000000..0x3efeffff -> 0x10000000
pci-host-generic 4010000000.pcie: MEM 0x8000000000..0xffffffffff -> 0x8000000000
pci-host-generic 4010000000.pcie: ECAM at [mem 0x4010000000-0x401fffffff] for [bus 00-ff]
pci-host-generic 4010000000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x10000000-0x3efeffff]
pci_bus 0000:00: root bus resource [mem 0x8000000000-0xffffffffff]
pci 0000:00:00.0: [1b36:0008] type 00 class 0x060000
$ lspci
00:00.0 Host bridge: Red Hat, Inc. QEMU PCIe Host bridge
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=eb01d42a77785ff96b6e66a2a2e7027fc6d78e4a
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Qemu for the aarch64 virt emulate an RTC PL031 device.
Enable the kernel support to allow setting the system time.
"date" now return the current time:
Sun Jul 5 20:38:50 UTC 2020
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The Qemu version present in readme.txt files was needed when
the Buildroot's Qemu defconfig was tested manually using the
qemu-system-<arch> binary already present on the host.
This information is now incorrect since we are using host-qemu
package, currently at 4.2.0 version, to do a runtime test since
0c79350638.
For m68k-q800, we can use the upstream qemu since 4.2.0 release
[1].
So, remove this line from the readme.txt.
[1] https://www.qemu.org/2019/12/13/qemu-4-2-0/
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This commit add the name of the Qemu defconfig file after each
qemu command line in order to retrieve it easily.
Since a readme.txt can be shared between several Qemu defconfig, we
need at least one qemu command line in readme.txt for each defconfig.
For now, ignore the qemu_arm_vexpress_tz_defconfig since it fail to build
due to python script issue [1]. Anyway the arm vexpress boot is tested
with qemu_arm_vexpress_defconfig.
[1] http://lists.busybox.net/pipermail/buildroot/2020-February/273738.html
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
On my machine, it happens once in a while that the virtualised machine
boots too fast for the rootfs to be available at the time the kernel
tries to mount it.
For example, board/qemu/arm-vexpress/readme.txt suggested changing
"-smp 1" up to "-smp 4". But doing so here causes a kernel panic:
VFS: Cannot open root device "mmcblk0" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
1f00 131072 mtdblock0
(driver?)
1f01 32768 mtdblock1
(driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(0,0)
So, add the oh-so-useful 'rootwait' option to all kernel command lines
for qemu defconfigs.
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Mark Corbin <mark.corbin@embecosm.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
qemu_aarch64_virt_defconfig (implicitly) specifies cortex-a53, so adjust the
QEMU command line to also emulate a a53 instead of a57.
Also adjust the defconfig to explicitly specify a53 for consistency/clarity.
Signed-off-by: Gerome Burlats <gerome.burlats@smile.fr>
Cc: Romain Naour <romain.naour@smile.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
All linux configs are renamed to a version neutral filename
to avoid further renaming on kernel bumps.
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.16.7 2.12.0 YES OK
arm_versatile 4.16.7 2.12.0 YES OK
arm_versatile_nommu 4.16.7 2.12.0 YES OK (3)
arm_vexpress 4.16.7 2.12.0 YES OK
m68k_mcf5208 4.16.7 2.12.0 YES OK
m68k_q800 4.16.7 q800-v2.11.0 NO (2) OK
microblazebe 4.16.7 2.12.0 YES OK
microblazeel 4.16.7 2.12.0 YES OK
mips32r2el_malta 4.16.7 2.12.0 YES OK
mips32r2_malta 4.16.7 2.12.0 YES OK
mips32r6el_malta 4.16.7 2.12.0 YES OK
mips32r6_malta 4.16.7 2.12.0 YES OK
mips64el_malta 4.16.7 2.12.0 YES OK
mips64_malta 4.16.7 2.12.0 YES OK
mips64r6el_malta 4.16.7 2.12.0 YES OK
mips64r6_malta 4.16.7 2.12.0 YES OK
nios2-10m50 4.16.7 2.12.0 NO OK
or1k 4.16.7 2.12.0 NO OK
ppc_g3beige 4.16.7 2.12.0 YES OK
ppc_mpc8544ds 4.16.7 2.12.0 YES OK
ppc_virtex_ml507 4.16.7 2.12.0 NO OK
ppc64_pseries 4.16.7 2.12.0 YES OK
ppc64le_pseries 4.16.7 2.12.0 YES OK
ppc64_e5500 4.16.7 2.12.0 YES OK
sh4 4.16.7 2.12.0 YES OK
sh4eb 4.16.7 2.12.0 NO (1) OK
sparc_ss10 4.16.7 2.12.0 YES OK
sparc64_sun4u 4.16.7 2.12.0 YES OK
x86 4.16.7 2.12.0 YES OK
x86_64 4.16.7 2.12.0 YES OK
xtensa_lx60 4.16.7 2.12.0 YES OK
xtensa_lx60_nommu 4.16.7 2.12.0 YES OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Kernel patch required, switched to devicetree usage
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The "virt" machine supports disk emulation, so use a ext4 rootfs instead of
initramfs for consistency with the other qemu defconfigs.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Xtensa patches no longer required, the make target name changed
to Image. The Qemu binary for OpenRisc was renamed upstream.
I removed the x86->x86_64 symlink, independent files preferred.
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.11.3 2.9.0 YES OK
arm_versatile 4.11.3 2.9.0 YES OK
arm_versatile_nommu 4.4.70 2.9.0 YES OK
arm_vexpress 4.11.3 2.9.0 YES OK
m68k_mcf5208 4.11.3 2.9.0 YES OK
m68k_q800 4.11.3 q800-v2.4.0 NO (2) OK
microblazebe 4.11.3 2.9.0 YES OK
microblazeel 4.11.3 2.9.0 YES OK
mips32r2el_malta 4.11.3 2.9.0 YES OK
mips32r2_malta 4.11.3 2.9.0 YES OK
mips32r6el_malta 4.11.3 2.9.0 YES OK
mips32r6_malta 4.11.3 2.9.0 YES OK
mips64el_malta 4.11.3 2.9.0 YES OK
mips64_malta 4.11.3 2.9.0 YES OK
mips64r6el_malta 4.11.3 2.9.0 YES OK
mips64r6_malta 4.11.3 2.9.0 YES OK
nios2-10m50 4.11.3 2.9.0 NO OK
or1k 4.11.3 2.9.0 NO OK (5)
ppc_g3beige 4.11.3 2.9.0 YES OK
ppc_mpc8544ds 4.11.3 2.9.0 YES OK
ppc_virtex_ml507 4.9.6 2.9.0 NO OK (3)
ppc64_pseries 4.11.3 2.9.0 YES OK
sh4 4.9.6 2.9.0 YES OK (4)
sh4eb 4.9.6 2.9.0 NO (1) OK (4)
sparc_ss10 4.11.3 2.9.0 YES OK
sparc64_sun4u 4.11.3 2.9.0 YES OK
sparc_sun4u 4.11.3 2.9.0 YES OK
x86 4.11.3 2.9.0 YES OK
x86_64 4.11.3 2.9.0 YES OK
xtensa_lx60 4.11.3 2.9.0 YES OK
xtensa_lx60_nommu 4.11.3 2.9.0 YES OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Kernel oops with 4.11.3 on boot
(4) - System is extremely slow with 4.11.3, needs further investigation
(5) - Qemu binary got renamed to qemu-system-or1k
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Also bump the pc samples since they're tied to the (base) qemu config.
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.9.6 2.6.0 YES OK (3)
arm_versatile 4.9.6 2.5.0 YES OK
arm_versatile_nommu 4.4.45 2.5.0 YES OK
arm_vexpress 4.9.6 2.5.0 YES OK
m68k_mcf5208 4.8.17 2.5.0 YES OK (6)
m68k_q800 4.9.6 q800-v2.4.0 NO (2) OK
microblazebe 4.9.6 2.5.0 YES OK
microblazeel 4.9.6 2.5.0 YES OK
mips32r2el_malta 4.9.6 2.5.0 YES OK
mips32r2_malta 4.9.6 2.5.0 YES OK
mips32r6el_malta 4.9.6 2.6.0 YES OK (3)
mips32r6_malta 4.9.6 2.6.0 YES OK (3)
mips64el_malta 4.9.6 2.5.0 YES OK
mips64_malta 4.8.17 2.5.0 YES OK (6)
mips64r6el_malta 4.9.6 2.7.0 YES OK (3)(4)
mips64r6_malta 4.9.6 2.7.0 YES OK (3)(4)
nios2-10m50 4.9.6 2.9.0 NO OK
or1k 4.9.6 2.5.0 NO OK
ppc_g3beige 4.9.6 2.5.0 YES OK
ppc_mpc8544ds 4.9.6 2.5.0 YES OK
ppc_virtex_ml507 4.9.6 2.5.0 NO OK
ppc64_pseries 4.9.6 2.5.0 YES OK
sh4 4.9.6 2.5.0 YES OK
sh4eb 4.9.6 2.5.0 NO (1) OK
sparc_ss10 4.9.6 2.5.0 YES OK
sparc64_sun4u 4.9.6 2.5.0 YES OK
sparc_sun4u 4.9.6 2.5.0 YES OK
x86 4.9.6 2.5.0 YES OK
x86_64 4.9.6 2.5.0 YES OK
xtensa_lx60 4.8.17 2.6.0 YES OK (6)
xtensa_lx60_nommu 4.8.17 2.6.0 YES OK (5)
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Known to fail with qemu versions lower than 2.6.0
(4) - Might work with 2.6.0, but the cpu definition changed in 2.7.0
(5) - Kept back on 4.8.x series since 4.9.x fails to build
(6) - Kept back on 4.8.x series since 4.9.x fails to boot
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Drop m68k-mcf5208 kernel patch since it's upstream.
Also bump the pc samples since they're tied to the (base) qemu config.
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.8.1 2.6.0 YES OK (3)
arm_versatile 4.8.1 2.5.0 YES OK
arm_vexpress 4.8.1 2.5.0 YES OK
m68k_mcf5208 4.8.1 2.5.0 YES OK
m68k_q800 4.8.1 q800-v2.4.0 NO (2) OK
microblazebe 4.8.1 2.5.0 YES OK
microblazeel 4.8.1 2.5.0 YES OK
mips32r2el_malta 4.8.1 2.5.0 YES OK
mips32r2_malta 4.8.1 2.5.0 YES OK
mips32r6el_malta 4.8.1 2.6.0 YES OK (3)
mips32r6_malta 4.8.1 2.6.0 YES OK (3)
mips64el_malta 4.8.1 2.5.0 YES OK
mips64_malta 4.8.1 2.5.0 YES OK
mips64r6el_malta 4.8.1 2.7.0 YES OK (3)(4)
mips64r6_malta 4.8.1 2.7.0 YES OK (3)(4)
ppc_g3beige 4.8.1 2.5.0 YES OK
ppc_mpc8544ds 4.8.1 2.5.0 YES OK
ppc_virtex_ml507 4.8.1 2.5.0 NO OK
ppc64_pseries 4.8.1 2.5.0 YES OK
sh4 4.8.1 2.5.0 YES OK
sh4eb 4.8.1 2.5.0 NO (1) OK
sparc_ss10 4.8.1 2.5.0 YES OK
sparc64_sun4u 4.8.1 2.5.0 YES OK
sparc_sun4u 4.8.1 2.5.0 YES OK
x86 4.8.1 2.5.0 YES OK
x86_64 4.8.1 2.5.0 YES OK
xtensa_lx60 4.8.1 2.6.0 YES OK
xtensa_lx60_nommu 4.8.1 2.6.0 YES OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Known to fail with qemu versions lower than 2.6.0
(4) - Might work with 2.6.0, but the cpu definition changed in 2.7.0
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Also bump the pc samples since they're tied to the (base) qemu config.
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.7 2.6.0 YES OK (3)
arm_versatile 4.7 2.5.0 YES OK
arm_vexpress 4.7 2.5.0 YES OK
m68k_mcf5208 4.7 2.5.0 YES OK
m68k_q800 4.7 q800-v2.4.0 NO (2) OK
microblazebe 4.7 2.5.0 YES OK
microblazeel 4.7 2.5.0 YES OK
mips32r2el_malta 4.7 2.5.0 YES OK
mips32r2_malta 4.7 2.5.0 YES OK
mips32r6el_malta 4.7 2.6.0 YES OK (3)
mips32r6_malta 4.7 2.6.0 YES OK (3)
mips64el_malta 4.7 2.5.0 YES OK
mips64_malta 4.7 2.5.0 YES OK
mips64r6el_malta 4.7 2.6.0 YES OK (3)
mips64r6_malta 4.7 2.6.0 YES OK (3)
ppc_g3beige 4.7 2.5.0 YES OK
ppc_mpc8544ds 4.7 2.5.0 YES OK
ppc_virtex_ml507 4.7 2.5.0 NO OK
ppc64_pseries 4.7 2.5.0 YES OK
sh4 4.7 2.5.0 YES OK
sh4eb 4.7 2.5.0 NO (1) OK
sparc_ss10 4.7 2.5.0 YES OK
sparc64_sun4u 4.7 2.5.0 YES OK
sparc_sun4u 4.7 2.5.0 YES OK
x86 4.7 2.5.0 YES OK
x86_64 4.7 2.5.0 YES OK
xtensa_lx60 4.7 2.6.0 YES OK
xtensa_lx60_nommu 4.7 2.6.0 YES OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Known to fail with qemu versions lower than 2.6.0
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The console problem goes away with qemu 2.6.0 so it seems it's now a
requirement, update readme.txt accordingly.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Results table:
Defconfig Kernel Qemu Network Status
------------------------------------------------------------------
aarch64_virt 4.5.3 2.5.0 YES OK
arm_versatile 4.5.3 2.5.0 YES OK
arm_vexpress 4.5.3 2.5.0 YES OK
m68k_mcf5208 4.5.3 2.5.0 NO SO-SO (3)
m68k_q800 4.5.3 q800-v2.4.0 NO (4) OK
microblazebe 4.5.3 2.5.0 YES OK
microblazeel 4.5.3 2.5.0 YES OK
mips64el_malta 4.5.3 2.5.0 YES OK
mips64_malta 4.5.3 2.5.0 YES OK
mipsel_malta 4.5.3 2.5.0 YES OK
mips_malta 4.5.3 2.5.0 YES OK
ppc_g3beige 4.5.3 2.5.0 YES OK
ppc_mpc8544ds 4.5.3 2.5.0 YES OK
ppc_virtex_ml507 4.5.3 2.5.0 NO OK
ppc64_pseries 4.5.3 2.5.0 YES OK
sh4 4.5.3 2.5.0 YES OK
sh4eb 4.5.3 2.5.0 NO (1) OK
sparc_ss10 4.5.3 2.5.0 YES OK
sparc64_sun4u 4.5.3 2.5.0 YES OK
sparc_sun4u 4.5.3 2.5.0 YES OK
x86 4.5.3 2.5.0 YES OK
x86_64 4.5.3 2.5.0 YES OK
xtensa_lx60 4.4.9 2.5.0 YES (2) OK
xtensa_lx60_nommu 4.4.9 2.5.0 YES (2) OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - xtensa ethernet broken in 4.5
(3) - It boots, you can login, but apps exit/crash often
(4) - There's a network interface, but enabling it in qemu fails
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
arm_versatile kernel defconfig updated to deal with multi-platform ARM
support and driver changes.
mips(el) 32-bits is back in working order for 4.5
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.5 2.3.0 YES OK
arm_versatile 4.5 2.3.0 YES OK
arm_vexpress 4.5 2.3.0 YES OK
microblazebe 4.5 2.3.0 YES OK
microblazeel 4.5 2.3.0 YES OK
mips64el_malta 4.5 2.3.0 YES OK
mips64_malta 4.5 2.3.0 YES OK
mipsel_malta 4.5 2.3.0 YES OK
mips_malta 4.5 2.3.0 YES OK
ppc_g3beige 4.5 2.3.0 YES OK
ppc_mpc8544ds 4.5 2.3.0 YES OK
ppc_virtex_ml507 4.5 2.3.0 NO OK
ppc64_pseries 4.5 2.3.0 YES OK
sh4 4.5 2.3.0 YES OK
sh4eb 4.5 2.3.0 NO (1) OK
sparc_ss10 4.5 2.3.0 YES OK
sparc64_sun4u 4.5 2.3.0 YES OK
sparc_sun4u 4.5 2.3.0 YES OK
x86 4.5 2.3.0 YES OK
x86_64 4.5 2.3.0 YES OK
xtensa_lx60 4.4.5 2.3.0 YES (2) OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - xtensa ethernet broken in 4.5 so stick to 4.4.x
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Keep arm_nuri on 3.10.x for the usual reasons.
Keep mips & mipsel (32 bits) on 4.3.x because 4.4.x fails to boot
properly (kernel stuck after the CPU cache info).
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.4.1 2.3.0 YES OK
arm_nuri 3.10.96 2.3.0 YES(1) OK most times(2)
arm_versatile 4.4.1 2.3.0 YES OK
arm_vexpress 4.4.1 2.3.0 YES OK
microblazebe 4.4.1 2.3.0 YES OK
microblazeel 4.4.1 2.3.0 YES OK
mips64el_malta 4.4.1 2.3.0 YES OK
mips64_malta 4.4.1 2.3.0 YES OK
mipsel_malta 4.3.5 2.3.0 YES OK (4)
mips_malta 4.3.5 2.3.0 YES OK (4)
ppc_g3beige 4.4.1 2.3.0 YES OK
ppc_mpc8544ds 4.4.1 2.3.0 YES OK
ppc_virtex_ml507 4.4.1 2.3.0 NO OK
ppc64_pseries 4.4.1 2.3.0 YES OK
sh4 4.4.1 2.3.0 YES OK
sh4eb 4.4.1 2.3.0 NO(3) OK
sparc_ss10 4.4.1 2.3.0 YES OK
sparc64_sun4u 4.4.1 2.3.0 YES OK
sparc_sun4u 4.4.1 2.3.0 YES OK
x86 4.4.1 2.3.0 YES OK
x86_64 4.4.1 2.3.0 YES OK
xtensa_lx60 4.4.1 2.3.0 YES OK
(1) - Supposed to work but broken, probably Qemu emulation issue
(2) - In like 1/3 starts it fails to work properly
(3) - Probably an endian issue with 8139 emulation/driver
(4) - Kernel stuck at cpu cache details from 4.4 - 4.4.1
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
ppc-mpc8544ds: switch to custom kernel config since the new 4.3-shipped
mpc85xx_basic_defconfig doesn't work with Qemu.
Incidentally while cleaning it up it now seems to work fine with newer
qemu versions.
sparc64_sun4u: ditch ne2k driver since it's useless, and add the e1000
driver which works fine.
x86: stick to 4.2.x kernels since 4.3 doesn't work right with uclibc
(any variant) based toolchains.
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.3 2.3.0 YES OK
arm_nuri 3.10.93 2.3.0 NO(1) OK(2)
arm_versatile 4.3 2.3.0 YES OK
arm_vexpress 4.3 2.3.0 YES OK
microblazebe 4.3 2.3.0 YES OK
microblazeel 4.3 2.3.0 YES OK
mips64el_malta 4.3 2.3.0 YES OK
mips64_malta 4.3 2.3.0 YES OK
mipsel_malta 4.3 2.3.0 YES OK
mips_malta 4.3 2.3.0 YES OK
ppc_g3beige 4.3 2.3.0 YES OK
ppc_mpc8544ds 4.3 2.3.0 YES OK
ppc_virtex_ml507 4.3 2.3.0 NO OK
ppc64_pseries 4.3 2.3.0 YES OK
sh4 4.3 2.3.0 YES OK
sh4eb 4.3 2.3.0 NO(1) OK
sparc_ss10 4.3 2.3.0 YES OK
sparc64_sun4u 4.3 2.3.0 YES OK
sparc_sun4u 4.3 2.3.0 YES OK
x86 4.2.6 2.3.0 YES OK(3)
x86_64 4.3 2.3.0 YES OK
xtensa_lx60 4.3 2.3.0 YES OK
(1) - Supposed to work but broken, probably Qemu emulation issue
(2) - In like 1/3 runs it fails to start properly
(3) - linux 4.3.0 doesn't like uclibc-based toolchains (net issues)
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update most of the configs to the latest kernel version (4.1) except for
arm-nuri which is stuck.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
qemu_arm_vexpress_defconfig is broken for 3.19 so keep it with 3.18.x
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
