This patch add support for Open Frame C.TOUCH 10.1 Kit.
Since the defconfig is no longer only for the starter kit, remove that
from BR2_TARGET_GENERIC_ISSUE.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add the new SAMA5D27 SOM1 Evaluation Kit with linux4sam_5.7 components.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The amount of GPU memory can be set using the new option --gpu_mem_XXX
(where XXX is the total amount of memory available on the board).
Signed-off-by: Gaël PORTAY <gael.portay@savoirfairelinux.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add an entry to explain how to run the glmark benchmark.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Bump the kernel version to 4.13.3.
Kernel 4.13.3 uses the /dev/dri/card0 device as rendering node, so
adjust it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
U-Boot 2017.09 uses SPL, so bump to this version so that we can
have a single qt5 image that supports the different imx6 sabresd
boards: imx6q, imx6dl and imx6qp.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Now that SPL is supported a single image can run on the different
variants of imx6 sabresd boards: imx6q, imx6dl and imx6qp.
So drop the 'quad' prefix from defconfig, directory and readme file
to make it generic.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Pass an offset of 1MB for the start of the rootfs.
Otherwise we get rootfs corruption when the bootloader is manually
written to the SD card.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This is similar to the ppc64_pseries config, except we build for little
endian instead of big endian.
The default architecture is set to Power8 as this was the first fully
enabled LE machine.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Peter: board is from Sinovoip, not Lemaker, move board files,
Use kernel headers from kernel, explicitly use 4.13.3,
drop eth0 dhcp config, cleanup post-build args,
disable tar output format, use u-boot custom format,
add host-dosfstools/mtools for genimage, drop unused
host-uboot-tools/genext2fs]
Signed-off-by: Mike Harmony <mike.harmony@snapav.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump to 4.13 kernel and remove all the dts patches as they
are part of upstream now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Kernel help-text states, "The ext4 filesystem requires that this feature
be enabled <...> otherwise, it will refuse to mount in the read-write
mode any filesystems that use the huge_file feature, which is enabled by
default by mke2fs.ext4."
If the rootfs is to be (re)mounted rw at boot, this must be set for the
system to successfully come up.
Signed-off-by: Nicholas Sielicki <sielicki@yandex.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The TS-7680 is an i.MX286 ARM ARM926EJ-S board with 10/100 Ethernet,
USB port, eMMC and CAN ports.
The TS-7680 uses a 3.14.28 Linux kernel provided by Technologic Systems:
https://github.com/embeddedarm/linux-3.14.28-imx28
U-Boot is not provided as the manufacturer recommends not to update the
built-in bootloader.
For more informations please see:
https://wiki.embeddedarm.com/wiki/TS-7680
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
[Thomas: use same headers as the kernel being built, update .gitlab-ci.yml.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
i.MX1/L boards require an old Linux kernel version to run, which is not
compatible with latest Buildroot needs.
Will fix:
https://gitlab.com/buildroot.org/buildroot/-/jobs/27873568
Signed-off-by: Julien BOIBESSOT <julien.boibessot@armadeus.com>
[Thomas: update .gitlab-ci.yml file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Our new WiFi 802.11ac BT4.1 module (BD-SDMAC [1]) driver allows to
override the wlan MAC address using a module parameter.
Since its driver is now included in our external repository [2], update
the bootscript so it sets the parameter for that driver too.
As a FYI, $wlmac is based on Ethernet MAC address located in fuses.
[1] https://boundarydevices.com/product/bd_sdmac_wifi/
[2] https://github.com/boundarydevices/buildroot-external-boundary
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for imx7d-pico, which is a board based on NXP
i.MX7D processor.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
[Thomas:
- add upstream references for the Linux kernel patches
- fix typoes in readme.txt
- remove audio-related packages in defconfig
- regenerate .gitlab-ci.yml]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The beaglebone_qt5_defconfig uses an older kernel version which does not
provide a device tree for the beagle bone green.
post-image.sh now selects genimage_linux41.cfg if am335x-bonegreen.dtb is
not build and genimage.cfg otherwise.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
[Thomas: minor tweaks.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Introduce imx6q-sabresd_qt5_defconfig that supports the opensource
Etnaviv graphical stack.
This defconfig provides a way to quickly test some graphical applications,
such as kmscube, qt5, glmark2.
Currently kernel mainline exhibits issues when running cpufreq as ondemand
governor on mx6, so add a linux fragment that disables such option for the
time being.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[Arnout:
- Add Fabio to DEVELOPERS
- Rename linux config fragment to linux_qt5.fragment
- Add comment to linux_qt5.fragment why it is needed
- Add explicit CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y to it
- Reorder defconfig entries to they match imx6q-sabresd_defconfig
- Remove strace and host-uboot-tools, neither seems to be needed
- Drop BR2_PACKAGE_QT5BASE_LICENSE_APPROVED, it no longer exists
- Replace BR2_TARGET_ROOTFS_EXT2_BLOCKS with BR2_TARGET_ROOTFS_EXT2_SIZE
- Regenerate .gitlab-ci.yml]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Bump U-Boot to 2017.07 and kernel to version 4.12.3.
As imx_v6_v7_defconfig in 4.12 selects CONFIG_CFG80211_WEXT=y,
remove the linux.fragment file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for nanopi-m1-plus board
with below features
- U-Boot 2017.07-rc3
nanopi-m1-plus dts support is present in rc3 version
- Linux 4.11.5
- linux patches to add nanopi-m1-plus dts
- Default packages from buildroot
Signed-off-by: Chakra Divi <chakra@openedev.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
And drop the version number from the linux configuration.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Drop the board specific patches which has been applied upstream.
[Peter: also drop now unused BR2_GLOBAL_PATCH_DIR]
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit adds a Linux kernel patch to solve a build failure with
the arcturus_ucp1020_defconfig with gcc 6.x:
arch/powerpc/kernel/ptrace.c:407:24: warning: index 32 denotes an offset greater than size of 'u64[32][1] {aka long long unsigned int[32][1]}' [-Warray-bounds]
offsetof(struct thread_fp_state, fpr[32][0]));
^
The patch is upstream in Linux, and can be dropped when
arcturus_ucp1020_defconfig is updated to use a new Linux kernel
version.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Main difference is that the drm driver now supports the hdmi output.
The gxl variant device tree has been renamed in:
commit 7eea67101b9713ae438955e8899b3c4b078419f9
Author: Kevin Hilman <khilman@baylibre.com>
Date: Fri Jan 20 07:57:52 2017 -0800
ARM64: dts: meson-gxl: rename Nexbox A95x for consistency
Since the GXL family has S905X and S905D SoCs, we're keeping the SoC
name in the DTS filename for clarity. Rename this file accordingly to
be consistent with the rest of the GXL DTS files.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
So adjust the defconfig and boot script to match.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Rather than bundle the overlay with us, directly fetch it from its
upstream location.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for nanopi-m1 board
with below features
- U-Boot 2017.07-rc1
- Linux 4.11.5
- Default packages from buildroot
Signed-off-by: Chakra Divi <chakra@openedev.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Manual change because the script uses ${OUTPUT_DIR}/host instead of
${HOST_DIR}.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Manual change because the script uses ${OUTPUT_DIR}/host instead of
${HOST_DIR}.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Since things are no longer installed in $(HOST_DIR)/usr, the callers
should also not refer to it.
This is a mechanical change with
git grep -l 'HOST_DIR}\?/usr/' board | xargs sed -i 's%\(HOST_DIR}\?\)/usr/%\1/%g'
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Chakra Divi <chakra@openedev.com>
[Thomas: remove host-uboot-tools from defconfig, already pulled by
BR2_TARGET_UBOOT_BOOT_SCRIPT, remove trailing whitespace.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Engicam Is.IoT MX6UL SOM board
with below features:
- U-Boot 2017.07-rc1
- Linux 4.11.5
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas: add host-dosfstools/host-mtools.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Engicam GEAM6UL SOM board
with below features:
- U-Boot 2017.07-rc1
- Linux 4.11.5
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas: add host-dosfstools and host-mtools.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Create board/engicam/icorem6 for i.CoreM6 supported files.
and update the readme.txt so-that it can list i.CoreM6 board
details.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Engicam i.CoreM6 Quad/Dual/DualLite/Solo RQS
board with below features:
- U-Boot 2017.07-rc1
- Linux 4.11.5
- Default packages from buildroot
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas: add missing host-dosfstools and host-mtools.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add initial support for Engicam i.CoreM6 DualLite/Solo board
with below features:
- U-Boot 2017.07-rc1
- Linux 4.11.5
- Default packages from buildroot
U-Boot 2017.07-rc1 has common u-boot defconfig for All i.CoreM6
variant boards, so this patch update the same along with
buildroot defconfig that reflect the common name.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Instead of a custom post-build script, use the boot script generation
logic of the U-Boot package.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for a13_olinuxino board
with below features
- U-Boot 2017.05
- Linux 4.11.5
- Default packages from buildroot
Signed-off-by: Chakra Divi <chakra@openedev.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Thomas:
- use full name in DEVELOPERS file
- remove parametrization of the post-build.sh script, just hardcode
the boot.cmd file used as input
- add missing dosfstools and mtools host packages in defconfig,
needed because a vfat partition is defined in the genimage.cfg
file
- minor tweaks to readme.txt file.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Default bootargs have changed in U-Boot for this board. Build U-Boot
environment and add it to the SD card image to update bootargs.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
at91sam9x5ek_mmc board was missing in the previous patch adding 1M
offset for FAT partition to solve some boot issues with the ROM code.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The recent change to default to gcc 6 for the internal toolchain broke this
defconfig as the u-boot and linux kernel are too old to build with gcc 6.
Fit it by backporting the following commits:
- u-boot: 9b2c282b34 (compiler*.h: sync include/linux/compiler*.h with Linux 4.5-rc6)
- linux: cb984d101b (compiler-gcc: integrate the various compiler-gcc[345].h files)
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
In commit 28d97609b2 ("configs/qemu:
bump to the latest kernel version") updated most qemu defconfigs to
use Linux 4.11. However, for the SH4 configurations, Linux 4.9 was
kept, because 4.11 apparently has an issue.
Unfortunately, while the defconfigs for SH4 were unchanged, the Linux
kernel configuration file was renamed from linux-4.9.config to
linux-4.11.config.
This commit renames the Linux configuration files back to their
previous name, linux-4.9.config, matching what the Qemu SH4 defconfigs
specify.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As the vendor folder friendlyarm is created, move board nanopi-neo
also under vendor folder.
Signed-off-by: Chakra Divi <chakra@openedev.com>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The board has an ethernet interface, so enable DHCP for it.
The used flash chip uses 16K erase blocks, so use that for JFFS2:
mtdinfo -a
..
mtd5
Name: user
Type: nand
Eraseblock size: 16384 bytes, 16.0 KiB
Amount of eraseblocks: 1915 (31375360 bytes, 29.9 MiB)
Minimum input/output unit size: 512 bytes
Sub-page size: 256 bytes
OOB size: 16 bytes
Character device major/minor: 90:10
Bad blocks are allowed: true
Device is writable: true
While we're at it, add a readme explaining how to build and upload the build
to the board.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Reusing the qemu x86-64 linux config isn't very obvious, so these defconfigs
aren't taken into consideration when the qemu defconfigs are updated,
breaking the build.
Instead use a custom linux config for the pc defconfigs. With this, we also
can get rid of the fragment file containing the delta fra the qemu config.
Created by linux-update-defconfig (after turning of the fragment file).
Also drop the linux kernel version number from the file name as it just
causes extra noise whenever the kernel is bumped.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for Engicam i.CoreM6 Quad/Dual board
with below features:
- U-Boot 2017.05
- Linux 4.11
- Default packages from buildroot
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use kernel 4.11 for stm32f4 discovery board
(stm32f429i-disco and stm32f469i-disco).
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch adds basic support for orangepi-zero board.
Board support package includes the following components:
- mainline kernel v4.11
- mainline u-boot v2017.03
- extra kernel config options: spidev, spi nor flash, wifi
- dts patches to enable SPI NOR and spidev
More details about this board are available here:
- http://linux-sunxi.org/Orange_Pi_Zero
Note that at the moment networking is not supported right out of the box.
Ethernet submission to mainline kernel is a work in progress, see the
latest dwmac-sun8i branches at https://github.com/montjoie/linux
On-board SDIO WiFi chip XR819 is supported by off-the-tree wireless
driver available at https://github.com/fifteenhex/xradio
Changes from v1:
* Send patch using proper subject
* Update xr819 kernel dts patch: add compatible property
[Peter: fix s/PC/Zero/ typo]
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Xtensa patches no longer required, the make target name changed
to Image. The Qemu binary for OpenRisc was renamed upstream.
I removed the x86->x86_64 symlink, independent files preferred.
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.11.3 2.9.0 YES OK
arm_versatile 4.11.3 2.9.0 YES OK
arm_versatile_nommu 4.4.70 2.9.0 YES OK
arm_vexpress 4.11.3 2.9.0 YES OK
m68k_mcf5208 4.11.3 2.9.0 YES OK
m68k_q800 4.11.3 q800-v2.4.0 NO (2) OK
microblazebe 4.11.3 2.9.0 YES OK
microblazeel 4.11.3 2.9.0 YES OK
mips32r2el_malta 4.11.3 2.9.0 YES OK
mips32r2_malta 4.11.3 2.9.0 YES OK
mips32r6el_malta 4.11.3 2.9.0 YES OK
mips32r6_malta 4.11.3 2.9.0 YES OK
mips64el_malta 4.11.3 2.9.0 YES OK
mips64_malta 4.11.3 2.9.0 YES OK
mips64r6el_malta 4.11.3 2.9.0 YES OK
mips64r6_malta 4.11.3 2.9.0 YES OK
nios2-10m50 4.11.3 2.9.0 NO OK
or1k 4.11.3 2.9.0 NO OK (5)
ppc_g3beige 4.11.3 2.9.0 YES OK
ppc_mpc8544ds 4.11.3 2.9.0 YES OK
ppc_virtex_ml507 4.9.6 2.9.0 NO OK (3)
ppc64_pseries 4.11.3 2.9.0 YES OK
sh4 4.9.6 2.9.0 YES OK (4)
sh4eb 4.9.6 2.9.0 NO (1) OK (4)
sparc_ss10 4.11.3 2.9.0 YES OK
sparc64_sun4u 4.11.3 2.9.0 YES OK
sparc_sun4u 4.11.3 2.9.0 YES OK
x86 4.11.3 2.9.0 YES OK
x86_64 4.11.3 2.9.0 YES OK
xtensa_lx60 4.11.3 2.9.0 YES OK
xtensa_lx60_nommu 4.11.3 2.9.0 YES OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Kernel oops with 4.11.3 on boot
(4) - System is extremely slow with 4.11.3, needs further investigation
(5) - Qemu binary got renamed to qemu-system-or1k
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This uses a genimage feature to rename the uImage file instead
of manually creating a symlink in the post-image script.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It is finally possible to boot LEGO MINDSTORMS EV3 from the mainline
Linux kernel. This patch updates the defconfg to use the mainline kernel
instead of the custom ev3dev kernel.
[Peter: lock kernel headers version]
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Since the bump of OpenOCD from 0.9.0 to 0.10.0 in commit
3b6c74d708, stm32f469_disco_defconfig
fails to build:
- 0001-add-config.patch was merged in upstream OpenOCD (commit
26045588f462476cee356d15a24944d6c26befb4).
- 0002-flash-nor.patch was merged in upstream OpenOCD (commit
3e219648c80a27f0519003f3b088cbb846e255d8)
Therefore, this commit removes the two patches that are no longer
necessary.
Fixes:
https://gitlab.com/buildroot.org/buildroot/builds/15762279
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This configuration builds a 64bit image for RaspberryPi 3.
The size of the ext4 filesystem has to be extended to fit the large amount
(~60MB) of kernel modules enabled in the defconfig.
[Peter: drop gcc version selection / glibc, explain ext4 size requirement]
Signed-off-by: Gaël PORTAY <gael.portay@savoirfairelinux.com>
Tested-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This change renders the stm32f429discovery a bit more generic and reuse most
of its settings for the stm32f429-disc1 board.
Cc: Waldemar Brodkorb <wbx@openadk.org>
Cc: Davide Viti <zinosat@tiscali.it>
Signed-off-by: Samuel Martin <s.martin49@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The patch for linux vdk defconfig introduced ARC_SMP_HALT_ON_RESET
config symbol. In fact that is not required as this symbol is enabled by
default if ARC_UBOOT_SUPPORT config symbol is set (and it is set in
vdk configs).
Also this commit fixes build failure, pointed us by Arnout:
https://gitlab.com/buildroot.org/buildroot/builds/14419270
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also use "BR2_TARGET_LINUX_CONFIG_FRAGMENT_FILES" instead of
"BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE".
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use two official kernel patches to add support for gcc 5:
commit 71458cfc782eafe4b27656e078d379a34e472adf
kernel: add support for gcc 5
commit aeea3592a13bf12861943e44fc48f1f270941f8d
ARM: 8158/1: LLVMLinux: use static inline in ARM ftrace.h
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
With this patch we add a couple of of-the-tree patches for u-boot.
We have an update in hardware that changed the kick-start slave cores
procedure. So these patches introduce fixes to work with new axs103
version correctly.
They have been already accepted in upstream u-boot so we need to get rid
of them as soon as these updates will get available in buildroot.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The gdbinit file assumes the .dtb file is in the current directory, so
let's start gdb from output/images.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
[Thomas: improved commit description.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
gx6605s is a nice SOC for dvbs2 DVB product, and C-SKY inside.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
[Thomas: drop post-image script copying the gdbinit file, and suggest
to use gdb -x option instead to point to the gdbinit file in board/.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Linux configs are missing memmap= option that is required for xtfpga
boards configured w/o device tree starting with linux-4.9. Add it.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit:
- Adds a development rootfs defconfig for the at91sam9x5ek board for
NAND-based configurations.
- Adds SD-card based configurations for the at91sam9x5ek board, both a
minimal one and development one.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
[Thomas: add at91sam9x5ek_mmc_defconfig to have all four combinations:
NAND minimal, NAND development, SD minimal, SD development.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This bump fix the build failure with gcc5 for barebox.
Some changes were made to the first patch to align to the latest
barebox api.
Also done the following changes:
- Use "BR2_TARGET_BAREBOX_CONFIG_FRAGMENT_FILES" instead of patching
the barebox sources.
- Use "BR2_GLOBAL_PATCH_DIR" instead of
"BR2_TARGET_BAREBOX_CUSTOM_PATCH_DIR".
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The board support package includes the following components:
- U-Boot 2016.11
- Linux 4.9.3
- packages:
- alsa-utils for basic audio usage of the on-board headphone jack
and microphone
- iw and wpa_supplicant for managing the wireless interface
Two Linux patches are necessary to enable audio and wifi support. Both
patches are fetched from the Linux next branch and are probably mainlined in
Linux 4.11.
A Linux configuration fragment enables the wireless device driver, which
is not enabled by default in the mainline defconfig of the board.
The wifi chip needs a NVRAM configuration file which is provided in the
rootfs overlay.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
[Thomas: remove e2fsprogs from the target packages, add entry in
DEVELOPERS file, remove C++ support.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
These defconfigs have been broken due to gcc5 for more than half a year,
and nobody stepped up to fix it. In addition, the rocketboards git
repository used by these defconfigs hasn't been reachable for more than
half a year. Finally, these defconfigs don't even use the
BR2_TARGET_UBOOT_ALTERA_SOCFPGA_IMAGE_CRC option so they are not a
great example for this family of targets.
Remove these defconfigs, as well as the board directory. Both are
removed in a single commit to avoid having an inconsistent readme.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Jan Viktorin <viktorin@rehivetech.com>
Cc: Charles Manning <cdhmanning@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This defconfig has been broken due to gcc5 for more than half a year,
and nobody stepped up to fix it. Remove it, as well as it board
directory.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Gergely Imreh <imrehg@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The scripts used for the minnowboards were generic for MinnowBoard and
MinnowBoard MAX. Since we removed the original MinnowBoard, this isn't
necessary anymore.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This defconfig has been broken due to gcc5 for more than half a year,
and nobody stepped up to fix it. Remove it, as well as the files it
references. Update the readme to remove references to MinnowBoard.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The imx6ul-liteboard dts patches have been upstreamed in kernel 4.10,
so bump to this version and remove the local patches
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The imx6sx-udoo-neo dts patches have been upstreamed in kernel 4.10,
so bump to this version and remove the local patches.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Nexbox A95X is a low cost Android STB based around an Amlogic s905(x) SoC
(quad A53), 8/16GB eMMC and 1/2GB RAM.
Both the s905 (gxbb) and s905x (gxl) variant is supported.
This defconfig uses mainline Linux. As the mainline support for s905 is
quite young, use the latest release candidate. There is currently no
support for this board in U-Boot or sources available for the vendor U-Boot,
so the defconfig doesn't build a u-boot and instead uses the existing U-Boot
available in the eMMC. This also means that we need to wrap the kernel as
uImage, which isn't suppported for aarch64. Instead this is done in the
post-build script.
Mainline aarch64 defconfig builds most drivers modular, so add mdev for
module autoloading.
[Peter: explicitly set BR2_cortex_a53=y]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
- update to released kernel and U-Boot,
- move the headers config closer to the kernel ones,
- update readme.txt.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
When manually writing SPL and u-boot.img to the SD card the rootfs
gets corrupted.
Fix this issue by passing a 1MB offset for the rootfs.
Reported-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This updates Linux kernel for Synopsys ARC HS38 VDK so it matches real
platform and while at it bump kernel version to the latest.
Main changes:
* Linux kernel v4.9.6 (latest in 4.9.x series in buildroot)
* Add support of MMC controller which is used for rootfs
* Add support of UIO which is used to communicate with EVSS
Now with this update image built by vanilla Buildroot VDK has
working UART, MMC, LCD, Ethernet, UIO etc.
And while at it we rename defconfing so it:
1) Doesn't mention SMP any more - that's the only option anyways now
2) Matches common naming scheme: vendor_arch_platform
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Zakharov Vlad <Vladislav.Zakharov@synopsys.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Also bump the pc samples since they're tied to the (base) qemu config.
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.9.6 2.6.0 YES OK (3)
arm_versatile 4.9.6 2.5.0 YES OK
arm_versatile_nommu 4.4.45 2.5.0 YES OK
arm_vexpress 4.9.6 2.5.0 YES OK
m68k_mcf5208 4.8.17 2.5.0 YES OK (6)
m68k_q800 4.9.6 q800-v2.4.0 NO (2) OK
microblazebe 4.9.6 2.5.0 YES OK
microblazeel 4.9.6 2.5.0 YES OK
mips32r2el_malta 4.9.6 2.5.0 YES OK
mips32r2_malta 4.9.6 2.5.0 YES OK
mips32r6el_malta 4.9.6 2.6.0 YES OK (3)
mips32r6_malta 4.9.6 2.6.0 YES OK (3)
mips64el_malta 4.9.6 2.5.0 YES OK
mips64_malta 4.8.17 2.5.0 YES OK (6)
mips64r6el_malta 4.9.6 2.7.0 YES OK (3)(4)
mips64r6_malta 4.9.6 2.7.0 YES OK (3)(4)
nios2-10m50 4.9.6 2.9.0 NO OK
or1k 4.9.6 2.5.0 NO OK
ppc_g3beige 4.9.6 2.5.0 YES OK
ppc_mpc8544ds 4.9.6 2.5.0 YES OK
ppc_virtex_ml507 4.9.6 2.5.0 NO OK
ppc64_pseries 4.9.6 2.5.0 YES OK
sh4 4.9.6 2.5.0 YES OK
sh4eb 4.9.6 2.5.0 NO (1) OK
sparc_ss10 4.9.6 2.5.0 YES OK
sparc64_sun4u 4.9.6 2.5.0 YES OK
sparc_sun4u 4.9.6 2.5.0 YES OK
x86 4.9.6 2.5.0 YES OK
x86_64 4.9.6 2.5.0 YES OK
xtensa_lx60 4.8.17 2.6.0 YES OK (6)
xtensa_lx60_nommu 4.8.17 2.6.0 YES OK (5)
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Known to fail with qemu versions lower than 2.6.0
(4) - Might work with 2.6.0, but the cpu definition changed in 2.7.0
(5) - Kept back on 4.8.x series since 4.9.x fails to build
(6) - Kept back on 4.8.x series since 4.9.x fails to boot
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add imx6q-sabresd_defconfig which supports imx6q-sabresd board using
mainline U-Boot and mainline kernel.
Keep freescale_imx6qsabresd_defconfig for those who want to run U-Boot and
kernel versions from NXP.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Board support package includes:
* Buildroot defconfig
* Mainline Linux kernel v4.9.6
* Mainline U-Boot (current HEAD revision is used, as board support
patches are not in stable release yet)
* genimage config to create sdcard image
* Board readme.txt
[Peter: use http:// instead of git:// for u-boot]
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This is used by buildroot default initscripts and results in some ugly
errors on startup otherwise.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
We no longer use the marked kernel.
Cc: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Since release 4.4 a kernel without a trailer is assumed to be device tree
capable. Since our Raspberry Pi defconfigs all use the newer firmware we can
just use the regular kernel image.
https://www.raspberrypi.org/documentation/configuration/device-tree.md
Tested on Raspberry Pi 3.
Cc: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
You can bootup a OpenRISC system, networking is not working.
[Peter: drop unneeded _GETTY_PORT="ttyS0" setting]
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Tested-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Patches from 4.8 version don't apply. Update them by backporting
liteBoard support from Linux master branch.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
There is already support in newest U-Boot version, so drop existing
U-Boot patches.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump to U-Boot 2017.01, which supports mx6sx_udoo_neo by default.
Remove the U-Boot patch that we used for the previous version.
Also adjust the 'fdtfile' name as it has been changed in U-Boot
mainline.
[Peter: part 2, boot.scr / defconfig changed accidently got dropped]
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump to U-Boot 2017.01, which supports mx6sx_udoo_neo by default.
Remove the U-Boot patch that we used for the previous version.
Also adjust the 'fdtfile' name as it has been changed in U-Boot
mainline.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Even though 'CONFIG_USB=n' does the job, let's switch to the more
standard way for disabling a Kconfig symbol.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use mainline 4.9 instead of a custom kernel based on NXP 4.1.
As mx7 boots in non-secure mode in mainline kernel, change the
U-Boot target to "warp7".
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This configuration provides a basic setup for using Buildroot
to create a sd-card image a BeagleBoard X15 board.
[Peter: use 512M ext4 partition, linux 4.9 and u-boot 2016.11]
Signed-off-by: Theo Debrouwere <Theo.Debrouwere@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The orangepi board variants use identical post-build and post-image scripts,
so move them up to board/orangepi and add symlinks in the variant
subdirectories, similary to how we handle it for the raspberry pi variants.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Board support package includes the following components:
- mainline u-boot 2016.09.01
- mainline kernel 4.9
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Rename orangepipc files, configs, and directories:
- oragepipc_defconfig -> orangepi_pc_defconfig
- board/orangepi/orangepipc -> board/orangepi/orangepi-pc
The purpose of the patch is to improve readability before
adding other boards of orangepi family.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The udoo neo files are currently placed inside udoo/neo directory.
Place the mx6qdl udoo related files inside udoo/mx6dl for consistency.
[Peter also update path in readme.txt]
Suggested-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add support for mx6sx udoo neo boards. For more information about these
boards, please check:
http://www.udoo.org/udoo-neo
The U-Boot and kernel dts patches will be removed when we bump U-Boot
to 2017.01 and kernel to 4.10 version as they have already been sent
upstream.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump to kernel 4.9 and remove the wifi dts patch as it is already
part of 4.9.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Backport 2 patches from upstream (from 3.18-rc1) for gcc 5.x support and a
patch from Marco Franceschetti (https://github.com/vonfritz/kernel/) to fix
gcc 5.x compat issues in the bsp wifi drivers.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add a fragment with configs from retired linux-3.18.config.
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
After the conversion to the common genimage scripts, the uImage.imx23-olinuxino
file no longer exists.
Instead of updating the section, let's simply remove it as the more
standard method of using sdcard.img is already explained.
This also makes the readme more consistent with the other i.MX readme files.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Make the SD card flashing procedure text consistent with the other i.MX
boards.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
After the conversion to the common genimage scripts the generated file list
is a bit different, so adjust it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The sama5d4ek defconfig has been removed in commit
9cb0b37cbd267ec1c2beea3deeaa86846bc2d037, but the board/atmel/readme.txt
file was not updated accordingly. This commit fixes that.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump to a recent version of AT91bootstrap and use mainline version of
U-Boot and Linux. This is needed to fix the build with gcc 5.x.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
[Thomas: add missing BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_8=y.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The calao defconfigs no longer build with gcc 5.x, due to Linux kernel
versions used being too old. However, it is unlikely that anyone will
ever update them, since Calao Systems has gone bankrupt in April 2016.
Therefore, let's remove them. If anyone is interested again at some
point, it will be easy to revive them from the Git history.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch to the kernel of release 4.1.15_2.0.0_ga, as it builds properly with
gcc 5.x, which is now the default.
We add a linux config fragment to disable the framebuffer, to repair the
build for imx_v6_v7_defconfig.
Suggested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: Julien Olivain <juju@cotds.org>
Tested-by: Julien Olivain <juju@cotds.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
[Thomas: adjust syntax in fragment.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
In order to have a better hierarchy for the genimage scripts used by
NXP mx25, mx51, mx53, mx6, mx7 SoCs, let's place them inside the
board/freescale/common/imx/ directory.
This helps in creating a more natural separation between the mxs scripts
that are placed inside the board/freescale/common/mxs/ directory.
Suggested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It was previously hardcoded to use the 1st partition although the
bootpart variable was used to download kernel/dtb from any partition.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The original submitter and follow-up contributors to the qmx6
defconfig no longer have the hardware available or the time/interest
to update this defconfig, which currently fails to build with gcc
5.x. Due to this, this commit removes this defconfig.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This defconfig no longer builds with gcc 5.x, and the original
submitter, Gustavo, no longer has the hardware to test this
configuration.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use the common mxs genimage script instead of a custom one.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add a standard genimage script for the MXS processors (MX23 and MX28).
Based on the common scripts for the other imx devices:
board/freescale/common/genimage.cfg.template
board/freescale/common/post-image.sh
This makes it easier to add new MX23/MX28 boards configurations into
Buildroot.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
With older SoCs and some SD cards, a 1024-bytes offset is needed to allow
ROM code to read the content of the FAT partition. As it is usual to get
a 1M bytes offset for the first partition, use this value to avoid boot
issues.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This defconfig is affected by bug #8516, reported more than a year ago,
and nobody has updated the defconfig since then. In addition, it should
be migrated to the genimage mechanism instead of having its own
mkcubieboard.sh script.
Therefore, let's get rid of this defconfig.
Fixes bug #8516.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Carlo Caione <carlo.caione@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The FriendlyARM Nanopi NEO is a 4x4cm² board with an Allwiner H3 SoC:
- quad-core Cortex-A7 @1.2GHz
- 256 or 512MiB of DDR
- uSDCard as only storage option
- 3x USB 2.0 host (one socket, two on expansion pin-holes)
- 1x USB 2.0 OTG (also used as power source)
- 10/100 etehrnet MAC
- GPIOs, SPI, I2c...
Support for the Nanopi NEO in U-Boot and Linux is very recent, so much
so that we have to use an -rc tag for U-Boot and a special Linux tree.
As for Linux, I pushed a git tree on Github with a single tag that
matches what is currently queued in the sunxi-next queued for 4.10,
based on 4.9-rc3. All those commits are from Maxime's tree, the
maintainer for most sunxi stuff.
This also means that we can't use the Linux headers from the kernel
being built (which is what we usually do) because those report 4.9,
while Buildroot currently knows only of 4.8 at best. So this is what we
use.
Unfortunately, support for the ethernet MAC and the USB OTG are not yet
upstream, but are being actively worked on.
The Nanopi NEO is very similar to the Orangepi PC, so I was able to
scanvenge most of its configuration. ;-)
Thanks Maxime for your help on IRC! :-)
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This uses the ev3dev linux extension to compile the ev3dev drivers for
LEGO MINDSTORMS EV3.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This adds a script to create SD card and flash images for LEGO MINDSTORMS
EV3 using the genimage tool.
The default kernel config had to be modified to add support for squashfs
and to add a ram disk.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Adding a comment to explain how to update the bootloader since it is
located in NOR flash memory.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Generate the standard sdcard.img format that can be directly copied
to the SD card.
Remove the custom create-boot-sd.sh script and update the readme.txt
file accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
[Thomas: further tweaks to readme.txt.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
When the SD card is connected to the host PC it can be mounted as
/dev/mmcblk0 or /dev/sdX, depending on how the SD controller is connected to
/the PC.
In this case the first partition is /dev/mmcblk0p1, not /dev/mmcblk01.
So use the ${PART1} variable to correctly assign this location.
[Peter: extend commit meesage]
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Use the common board/freescale/common/post-image.sh script instead of
a custom one.
As the final image binary is called "sdcard.img" update the documentation
accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Binutils was locked down to 2.24 because U-Boot 2014.01 didn't build
with more recent binutils. However, this doesn't work anymore because
binutils 2.24 is deprecated.
Current U-Boot 2016.09.01 doesn't work out of the box because the
u-boot-nand.img support has been removed.
Since updating U-Boot is generally not needed anyway, we just remove
the U-Boot support.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Binutils was locked down to 2.24 because U-Boot 2014.01 didn't build
with more recent binutils. However, this doesn't work anymore because
binutils 2.24 is deprecated.
Current U-Boot 2016.09.01 does build successfully, but we don't have a
board anymore to test it.
Since updating U-Boot is generally not needed anyway, we just remove
the U-Boot support.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump kernel revision used by lego_ev3_defconfig to the latest tag from
ev3dev, as suggested by Peter. This is a 4.4 series kernel, which has the
added benefit of not necessitating a specific gcc to boot.
We need a patch to create an empty drivers/lego/Kconfig file for the build
to succeed though, as the ev3dev kernel normally expects a drivers tree to
be checked out there.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Suggested-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This configuration allows out-of-the box Digilent Zybo
support. It uses mainline U-boot and Linux kernel.
This configuration generates a SD card image named sdcard.img.
[Peter: rename genimage.cfg, cleanup post-image script, enable VFP support,
use 4.6 kernel headers and add tools needed by genimage]
Signed-off-by: Sebastien Van Cauwenberghe <svancau@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add a target configuration for the beaglebone that supports the SGX530
graphics acceleration and builds the qt5 demos with the eglfs backend.
The imagination technologies demos and fbv are also included. The Linux
kernel is based on the omap2plus defconfig, a config fragment adds the
required settings for SGX accelerator support.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch updates the target config for the beaglebone based on the
AM335x CPU. It also supports the beagleboneblack, the TI evm and evmsk.
Device tree blobs for am335x-evm, am335x-evmsk, am335x-bone,
am335x-boneblack will be built and a sd card image is created with a
post-image script. The kernel and driver versions match the
ti-processor-sdk 02.00.00.00. Patches allow the use of old AM335x evm
revisions (1 bit sd card) and JTAG debugging.
Kernel JTAG patch: By default the kernel will disable the JTAG clock,
access via the JTAG port will not work after the kernel booted. The
AM335x-evm has a JTAG header fitted, this patch keeps the JTAG clock
alive.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
[Thomas: remove 1-bit MMC patch, it's causing a significant performance
regression for users of BeagleBone, which are 99.99% of the users of
this defconfig.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Thanks to the recent addition of the vexpress-firmware and
arm-trusted-firmware packages, this commit improves the ARM Juno
defconfig to also build a bootloader.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Useful for testing no-MMU ARM code in Qemu.
The newer Linux kernels with DT support for Qemu Versatile aren't yet
working, so use latest 4.4 kernel.
Signed-off-by: Waldemar Brodkorb <wbx@uclibc-ng.org>
Tested-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Drop m68k-mcf5208 kernel patch since it's upstream.
Also bump the pc samples since they're tied to the (base) qemu config.
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.8.1 2.6.0 YES OK (3)
arm_versatile 4.8.1 2.5.0 YES OK
arm_vexpress 4.8.1 2.5.0 YES OK
m68k_mcf5208 4.8.1 2.5.0 YES OK
m68k_q800 4.8.1 q800-v2.4.0 NO (2) OK
microblazebe 4.8.1 2.5.0 YES OK
microblazeel 4.8.1 2.5.0 YES OK
mips32r2el_malta 4.8.1 2.5.0 YES OK
mips32r2_malta 4.8.1 2.5.0 YES OK
mips32r6el_malta 4.8.1 2.6.0 YES OK (3)
mips32r6_malta 4.8.1 2.6.0 YES OK (3)
mips64el_malta 4.8.1 2.5.0 YES OK
mips64_malta 4.8.1 2.5.0 YES OK
mips64r6el_malta 4.8.1 2.7.0 YES OK (3)(4)
mips64r6_malta 4.8.1 2.7.0 YES OK (3)(4)
ppc_g3beige 4.8.1 2.5.0 YES OK
ppc_mpc8544ds 4.8.1 2.5.0 YES OK
ppc_virtex_ml507 4.8.1 2.5.0 NO OK
ppc64_pseries 4.8.1 2.5.0 YES OK
sh4 4.8.1 2.5.0 YES OK
sh4eb 4.8.1 2.5.0 NO (1) OK
sparc_ss10 4.8.1 2.5.0 YES OK
sparc64_sun4u 4.8.1 2.5.0 YES OK
sparc_sun4u 4.8.1 2.5.0 YES OK
x86 4.8.1 2.5.0 YES OK
x86_64 4.8.1 2.5.0 YES OK
xtensa_lx60 4.8.1 2.6.0 YES OK
xtensa_lx60_nommu 4.8.1 2.6.0 YES OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Known to fail with qemu versions lower than 2.6.0
(4) - Might work with 2.6.0, but the cpu definition changed in 2.7.0
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add the initial support for mx6q/dl udoo boards.
For information about these boards, please visit:
http://www.udoo.org/
In linux.fragment we disable USB support for now because kernel 4.8
hangs on udoo board.
This is been addressed by Peter Chen's kernel patch series that provides
a standard way to reset a USB hub.
When such series hit mainline, then we can bump the kernel and remove
linux.fragment.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Since U-Boot supported SPL for Zynq boards at v2014.04 release, it
became much easier to build a system. At that time, however, users
still needed to manually copy ps7_init.c/h to the U-Boot source tree
to generate a working SPL image because ps7_init.c/h output from
Xilinx tools are not compatible with GPL.
Later, the license problem was solved when Xilinx tools became able
to output the GPL-compatible variants (ps7_init_gpl.c/h) as well.
U-Boot v2015.07 or later includes ps7_init_gpl.c/h for major Zynq
boards so that users can build a boot image straight away.
Now Buildroot supports 3 boards (Zedboard, MicroZed, ZC706) without
any manual intervention. This is a good thing itself, but commit
b9cd72cdbf ("zynq_zc706: bump U-Boot to xilinx-v2016.2") entirely
dropped the information about custom ps7_init files.
This commit provides up-to-date guidance for how to customize the
ps7_init files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Matt Weber <matthew.weber@rockwellcollins.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
[Thomas: rewording and formatting tweaks.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As we are using the common image layout now, update the
readme.txt file accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Using the common board/freescale/common/post-image.sh can lead
to some good amount of simplification.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- configs/acmesystems_aria_g25_128mb_defconfig,
configs/acmesystems_aria_g25_256mb_defconfig :
update default configuration files for both 128MB and 256MB version
- board/acmesystems/aria-g25/genimage.cfg
board/acmesystems/aria-g25/post-image.sh :
add support for genimage in order to build sdcard.img
- board/acmesystems/aria-g25/readme.txt : update documentation
for Aria G25 and add notes about how to build sdcard.img
Signed-off-by: Biagio Montaruli <biagio.hkr@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Warp7 has a BRCM43430 Wifi chipset. Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
- enable BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS in raspberrypi3_defconfig
- add copy of rpi-firmware/overlays directory to boot partition in genimage-raspberrypi3.cfg
- enhance post-image.sh script to add 'dtoverlay=pi3-miniuart-bt' on request
- add BR2_ROOTFS_POST_SCRIPT_ARGS="--add-pi3-miniuart-bt-overlay" in raspberrypi3_defconfig
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The TS-4900 uses a custom Linux 4.X from Technologic Systems:
https://github.com/embeddedarm/linux-3.10.17-imx6/tree/imx_4.1.15_1.0.0_ga
Indeed, it is not supported by mainline Linux but this work is ongoing.
This patch is inspired by a previous work for the TS-4800.
A post image script is provided to generate an image that can be
directly written to an SD card. It also adds an fpga wifi module.
Signed-off-by: Mathieu Audat <mathieu.audat@savoirfairelinux.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
There is no need to handle this return code, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
There's now an sun8i-h3-orangepi-pc dts, so we can use that and drop the
hack in the post-image script.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
With kernel 4.8-rc5 we no longer need to use the "CONFIG_SMP=n" workaround
as the reboot issue has been fixed upstream by commit 059e232089e4
("irqchip/gic: Allow self-SGIs for SMP on UP configurations")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Make explicit that a ext4 rootfs is used.
As explained by Thomas Petazzoni:
"the ext4 filesystem is already used.
Indeed, the ext4 image is a symlink to the ext2 image, and the ext2
image is in fact an ext4 image:
-rw-r--r-- 1 thomas thomas 3763200 sept. 11 21:54 rootfs.ext2
lrwxrwxrwx 1 thomas thomas 11 sept. 11 21:54 rootfs.ext4 -> rootfs.ext2"
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As reported by bug #9176 the current v4.6 kernel config
(used by Minnowboard MAX and Turbot) does not support
USB disks. Since this is a pretty essential functionality,
it's desirable to have it, so let's add the required options.
Kernel config linux-v3.8.config (currently used by the first
generation Minnowboard) doesn't need this change.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The boards imx6dlsabreauto, imx6dlsabresd, imx6qsabreauto, imx6qsabresd,
imx6sxsabresd were referring to board/freescale/create-boot-sd.sh for
the sdcard image generation.
This commit:
* Removes board/freescale/create-boot-sd.sh
* Uses the common Freescale genimage template instead.
The offset of the first partition was 1MB in the script and is
modified to 8MB in the template.
* Fixes the readme.txt file accordingly
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
For the boards imx6ulevk, imx6sabresd, mx25pdk, mx51evk, mx53loco,
warpboard:
* Replace genimage.cfg with a common Freescale genimage template named
genimage.cfg.template because they all use the same layout. The only
difference comes from the device tree blobs.
* Replace each post-image.sh script with a generic post-image.sh script
which is able to generate the right genimage.cfg depending on:
** the image type (zImage or uImage) from BR2_LINUX_KERNEL_UIMAGE
** the device tree blobs from BR2_LINUX_KERNEL_INTREE_DTS_NAME
** the rootfs type (ext2, ext3 or ext4) from BR2_TARGET_ROOTFS_EXT2
* Fix the readme.txt files accordingly
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
[Thomas: remove handling of rootfs type, using rootfs.ext2 in all cases
is fine, rootfs.ext3 and rootfs.ext4 are just symbolic links to it.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Upgrade U-Boot version to 2016.07 and make proper use of U-Boot
distro configuration features.
Provide a boot.scr binary script that is one of the standard ways to
pass a U-Boot script with distro features enabled.
With this method the uboot-env.txt file is no longer needed, so it is
removed.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for warp7, which is a board based on NXP i.MX7S processor.
More information about warp7 can be found at:
https://www.element14.com/community/docs/DOC-79058
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit updates the kernel for Galileo board BSP from 3.8 to 3.14.
Signed-off-by: Padraig Connolly <padraig.connolly@intel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The recent U-Boot adopts Kconfig for its configuration system.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As pointed out in bug #9161, we don't always have an inittab file (if
systemd or no init is used), so the post build script should only try to
tweak it if present.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As pointed out in bug #9161, we don't always have an inittab file (if
systemd or no init is used), so the post build script should only try to
tweak it if present.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Greg Ungerer fixed recently a bug in the Linux kernel, which
allows to use one memory region again.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
[Thomas: cherry-picked from next to master, in order to be able to use
BR2_BINFMT_FLAT_ONE by default on m68k, since BR2_BINFMT_FLAT_SEP_DATA
causes too much problems.]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The pc_x86_64_efi reference defconfig is targeted towards an EFI
environment but the kernel which comes with it does not enable EFI
support by default.
Booting this defconfig without kernel EFI support on a qemu virtual
machine with EFI firmware resulted in no output to tty1 or ttyS0.
Enabling EFI support in the kernel fixed this and seems saner for an EFI
reference Buildroot defconfig.
Adding CONFIG_EFI to board/pc/linux-extras.config also affects
pc_x86_64_bios_defconfig which doesn't require it, however it was
observed that the extra overhead is small and so this is preferred
rather than having a separate config file.
This was tested with qemu 2.6.0 running with kvm enabled and firmware
EFI v2.60 by EDK II. Also built and verified bios defconfig on the same
setup but with BIOS firmware instead.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Cc: Gustavo Zacarias <gustavo@zacarias.com.ar>
Acked-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The instructions listed sdcard.img as output image name but
board/pc/genimage-*.cfg generate it named as disk.img instead.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Redirect the console output to the screen and not only to the serial
port.
Signed-off-by: Dagg Stompler <daggs@gmx.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
imx6ul has currently an issue on kernel 4.7 that causes a stall when running
the "reboot" command.
This issue has been reported in the linux-arm-kernel mailing list, but we
don't have a proper fix at the moment.
This problem is not seen when SMP is disabled, so let's disable it for now
until a proper fix becomes available.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
imx6ulpico has a BCM4339 Wifi chip. Add Wifi support by default
to allow a better customer experience.
The dts patch has already been sent to the linux-arm-kernel list
and we can remove it once it reaches a mainline kernel (in
version 4.9 probably).
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Let the wireless packages be selected by default to make the
usage of Wifi a bit simpler.
Suggested-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
There is no need for the 'exit' statement in the post-image scripts,
so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Provide a more complete set of instructions on how to get Wifi
working on the warpboard.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The readme.txt for the three boards are almost the same, so merge
them into board/zynq/readme.txt.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is the latest release tag in the Xilinx repository, based on
U-Boot v2016.01 in the mainline. It includes proper ps7_init_gpl.c/h
in it, so builds working SPL without any manual intervention.
BR2_TARGET_UBOOT_BOARD_NAME should be changed to zynq_zc706 since
U-Boot now has separate defconfig files for ZC702 and ZC706 boards.
BR2_TARGET_UBOOT_SPL_NAME should be changed to spl/boot.bin since
the Zynq image support for the mkimage tool was upstreamed and it
now generates boot.bin under spl/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is the latest release tag in the Xilinx repository, based on
U-Boot v2016.01 in the mainline. To sync with the Zedboard updates,
switch over to the Xilinx GitHub repository.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is the latest release tag in the Xilinx repository, based on
U-Boot v2016.01 in the mainline.
Commit 46d6a561be ("zedboard: Generate BOOT.BIN automatically")
switched from the Xilinx GitHub repository to the U-Boot mainline,
but this commit gets it back to the Xilinx GitHub repository for the
following reasons:
- This defconfig still relies on the Xilinx's local repository for
the kernel. The vendor does the best test for the combination of
U-Boot and the kernel with the same release tag (xilinx-v2016.2
in this case).
- At the time of commit 46d6a561be, the u-boot-xlnx still needed
manual copy of ps7_init(_gpl).c/h in order to build a working SPL
image. So, the mainline U-Boot had advantage in that point of
time. However, the improvement in the mainline U-Boot was merged
into the u-boot-xlnx at the xilinx-v2015.3 release. Now, the
mainline and the u-boot-xlnx are even in this point of view.
- The mainline U-Boot defaults to boot FIT, so something must be
done; either patch environments around with a local patch to
switch to uImage booting (current solution), or build an FIT
with a post build script (chromebook snow does this). On the
other hand, the Xilinx repository defaults to uImage booting,
so it is straightforward, and needs no addition care.
This commit does:
- Switch to the Xilinx custom git repository, and stick to the
xilinx-v2016.2 tag.
- Delete the local patch board/avnet/zedboard/uboot/0001...
since the Xilinx custom repository can boot uImage by default.
- Enable BR2_TARGET_UBOOT_FORMAT_IMG instead of ..._FORMAT_DTB_IMG
since all the Zynq boards in U-Boot enable CONFIG_OF_EMBED.
- Replace BR2_TARGET_UBOOT_ZYNQ_IMAGE with BR2_TARGET_UBOOT_SPL_NAME
since U-Boot can natively generate the Zynq boot image now. The
Zynq image support for mkimage tool was upstreamed at v2016.01
(so xilinx-v2016.1 as well), so no additional tool is needed
any more.
- Update readme.txt
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Selecting the driver CONFIG_BRCMFMAC as built-in causes some probe issues
as we cannot guarantee that the brcmfmac driver will be probed after the
rootfs has been mounted. The brcmfmac driver retrieves the firmware and
nvram file from the rootfs, so the rootfs should be mounted first.
To avoid such issues let the CONFIG_BRCMFMAC be built as module, which is
the original option in imx_v6_v7_defconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also bump the pc samples since they're tied to the (base) qemu config.
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.7 2.6.0 YES OK (3)
arm_versatile 4.7 2.5.0 YES OK
arm_vexpress 4.7 2.5.0 YES OK
m68k_mcf5208 4.7 2.5.0 YES OK
m68k_q800 4.7 q800-v2.4.0 NO (2) OK
microblazebe 4.7 2.5.0 YES OK
microblazeel 4.7 2.5.0 YES OK
mips32r2el_malta 4.7 2.5.0 YES OK
mips32r2_malta 4.7 2.5.0 YES OK
mips32r6el_malta 4.7 2.6.0 YES OK (3)
mips32r6_malta 4.7 2.6.0 YES OK (3)
mips64el_malta 4.7 2.5.0 YES OK
mips64_malta 4.7 2.5.0 YES OK
mips64r6el_malta 4.7 2.6.0 YES OK (3)
mips64r6_malta 4.7 2.6.0 YES OK (3)
ppc_g3beige 4.7 2.5.0 YES OK
ppc_mpc8544ds 4.7 2.5.0 YES OK
ppc_virtex_ml507 4.7 2.5.0 NO OK
ppc64_pseries 4.7 2.5.0 YES OK
sh4 4.7 2.5.0 YES OK
sh4eb 4.7 2.5.0 NO (1) OK
sparc_ss10 4.7 2.5.0 YES OK
sparc64_sun4u 4.7 2.5.0 YES OK
sparc_sun4u 4.7 2.5.0 YES OK
x86 4.7 2.5.0 YES OK
x86_64 4.7 2.5.0 YES OK
xtensa_lx60 4.7 2.6.0 YES OK
xtensa_lx60_nommu 4.7 2.6.0 YES OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Known to fail with qemu versions lower than 2.6.0
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Currently warpboard uses a 4.0.5 kernel version from github.
Move to version 4.4.15, which is a long term supported kernel version.
With 4.4.15 we no longer need the extra two kernel patches as they have
already been upstreamed.
Use a linux fragment file, so that wireless can be functional by default.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Generate an sdcard.img image to make it easier the deployment of a
Buildroot image.
[Peter: drop unneeded exit statement in post-image script]
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
