Results table:
Defconfig Kernel Qemu Network Status
------------------------------------------------------------------
aarch64_virt 4.5.3 2.5.0 YES OK
arm_versatile 4.5.3 2.5.0 YES OK
arm_vexpress 4.5.3 2.5.0 YES OK
m68k_mcf5208 4.5.3 2.5.0 NO SO-SO (3)
m68k_q800 4.5.3 q800-v2.4.0 NO (4) OK
microblazebe 4.5.3 2.5.0 YES OK
microblazeel 4.5.3 2.5.0 YES OK
mips64el_malta 4.5.3 2.5.0 YES OK
mips64_malta 4.5.3 2.5.0 YES OK
mipsel_malta 4.5.3 2.5.0 YES OK
mips_malta 4.5.3 2.5.0 YES OK
ppc_g3beige 4.5.3 2.5.0 YES OK
ppc_mpc8544ds 4.5.3 2.5.0 YES OK
ppc_virtex_ml507 4.5.3 2.5.0 NO OK
ppc64_pseries 4.5.3 2.5.0 YES OK
sh4 4.5.3 2.5.0 YES OK
sh4eb 4.5.3 2.5.0 NO (1) OK
sparc_ss10 4.5.3 2.5.0 YES OK
sparc64_sun4u 4.5.3 2.5.0 YES OK
sparc_sun4u 4.5.3 2.5.0 YES OK
x86 4.5.3 2.5.0 YES OK
x86_64 4.5.3 2.5.0 YES OK
xtensa_lx60 4.4.9 2.5.0 YES (2) OK
xtensa_lx60_nommu 4.4.9 2.5.0 YES (2) OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - xtensa ethernet broken in 4.5
(3) - It boots, you can login, but apps exit/crash often
(4) - There's a network interface, but enabling it in qemu fails
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Config can be used by other noMMU targets as qemu-system-m68k
with coldfire emulation.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch the invocation command to use virtio-blk and virtio-net for
better performance.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It has better performance for block and net.
Enable virgl (DRM_VIRTIO_GPU) support for 3D acceleration.
And also DRM_BOCHS for better stdvga acceleration.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It's exactly the same as the x86_64 variant so just create a symlink.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
So far identical to the rpi2 one except for the dts file as the SW runs in
32bit mode.
[Peter: extend commit message]
Signed-off-by: Ubaldo Porcheddu <ubaldo@eja.it>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The ODROID-C2 is a 64-bit quad-core single board computer(SBC) that is
one of the most cost-effective 64bit development boards available in the
ARM world.
http://www.hardkernel.com/main/products/prdt_info.php?g_code=G145457216438
[Peter: fix typos, drop neon/C++ settings, use git hash for Linux/U-Boot]
Signed-off-by: Brian Kim <brian.kim@hardkernel.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The defconfigs for the Raspberry Pi boards start a console on HDMI in
addition to the classic one on UART. Document this feature in the
readme.
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Arnout Vandecappelle <arnout@mind.be>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit adds a new defconfig to build a X-based
graphical system for the Minnowboard MAX board.
* The 'openbox' windows manager is chosen because it's simple
and lightweigth.
* Basic X apps are enabled (such as xrandr, xterm), so we
can at least get a console and change video mode.
* ALSA default configuration is provided, so HDMI audio
works out-of-the-box.
* OpenGL is supported.
Tested on Minnoboard Turot (which is Minnowboard Max compatible).
[Peter: drop unneeded/specific toolchain config options]
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit enables support for:
* HDMI audio
* Support for user-provided EDID firmware
(useful to workaround broken monitors)
* Evdev interface
* System V IPC (required by ALSA)
The options make the system more useful.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Given Minnowboard and Minnowboard MAX boards are very similar,
it's desirable to unify the support for them.
This commit does the following:
1) Remove Minnowboard MAX's genimage.cfg, post-build.sh
and post-image.sh. These are identical to Minnowboard's.
2) Move Minnowboard MAX's linux config, and rename it.
It would be lovely to have a single kernel config file.
The kernel size penalty involved in adding support for
all the peripherals on both boards is small enough to
justify this.
However, the original Minnowboard has some GPIO buttons
that need to be registered by the kernel. This is not
upstreamed, and hence we need to use the yocto v3.8 kernel
to have this support.
3) Rename each grub config to grub-{board}.cfg.
4) Modify (the now unique) post-build script to use
a different grub config, according to the board.
5) Update both defconfigs, as per the above changes.
6) Finally, update the readme.txt.
[Peter: mention MAX in readme title]
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Let's rework the board and config files to use genimage
to generate the SD card image directly.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add noMMU configuration running on dc233c MMUv3 core with identity
memory map.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
dc232b is MMUv2 core, dc233c is very similar MMUv3 core. MMUv3 is the
latest full MMU for xtensa, which allows running both MMU and noMMU
linux variants.
Update configuration overlay and linux config file.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Tested-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current Buildroot defconfigs for Raspberry Pi and Raspberry Pi 2
instantiate a console on tty1, which appears on HDMI. Add a console on
the serial port (ttyAMA0) to be more consistent with other defconfigs
and provide a better out-of-the-box experience to users used to have a
serial console from Buildroot defconfigs.
This requires three changes:
1. have two 'console=' entries in the kernel command line: tty1,
then ttyAMA0;
2. change BR2_TARGET_GENERIC_GETTY_PORT to "console", so it starts
a getty on the last console= passed to the kernel, ttyAMA0;
3. add a new getty on tty1 to the generated inittab.
Step 2 is actually obtained by removing BR2_TARGET_GENERIC_GETTY_PORT
entirely from the defconfigs, since "console" is the default value.
Step 3 requires a post-build script since the Buildroot makefiles can
configure only one console.
Note: instead of simply adding a new getty on ttyAMA0 (which would
work) this patch actually changes BR2_TARGET_GENERIC_GETTY_PORT to
instantiate a console on UART, then adds back tty1 via
post-build.sh. This is done only to avoid the "GENERIC_SERIAL" comment
where we instantiate an HDMI console, then instantiate a really-serial
console on another line.
The result is these two inittab lines:
console::respawn:/sbin/getty -L console 0 vt100 # GENERIC_SERIAL
tty1::respawn:/sbin/getty -L tty1 0 vt100 # HDMI console
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Arnout Vandecappelle <arnout@mind.be>
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Similar to stm32f429_disco, this commit adds a configuration for the
Cortex-M4 based STM32F469 platform.
It requires a few kernel patches, which have already been submitted
upstream, as well as a small OpenOCD patch. Besides that, it re-uses
most of what has been added for the STM32F429 platform.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Thomas:
- squash multiple patches from Lee Jones into one
- improve the readme.txt file
- sync the defconfig with the adaptations made to the stm32f429
configuration.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit adds a defconfig for the STM32F429 platform, which is
based on a Cortex-M4 core from ST Microelectronics. It is therefore
the first noMMU ARM platform supported in Buildroot.
This commit includes some files that will be common to several STM32
platforms (hence in board/stmicroelectronics) and some files that are
specific to the STM32F429 (hence in
board/stmicroelectronics/stm32f429-disco). More specifically, this
commit adds:
- A minimal Busybox configuration, which is small enough to boot
without causing OOM on such small noMMU platforms. The resulting
Busybox, statically linked with uClibc-ng, weights around 220
KB. For now, this file is located in board/stmicroelectronics/, but
we might consider moving it to package/busybox/ in the future if
needed.
- A post-build script that removes the mounting of /dev/pts (not
enabled in the kernel and not very useful for a system that has no
network and no X), and removes the network related init script and
configuration files (no network support).
- A flash.sh script, to perform the right OpenOCD invocations to
reflash the board.
- One small kernel patch to adjust the kernel command line in the
Device Tree, since it's the only way to do so.
- The usual readme.txt file.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Thomas:
- squashed multiple patches from Lee Jones together
- added the minimal Busybox configuration
- added the post-build script
- improved the flashing script to not hardcode the location of the
output directory
- add the small kernel patch
- improve the readme.txt file
- test on HW the resulting image, after using the internal toolchain.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Henceforth, a sdcard.img file is automatically generated. It simplifies the
procedure to generate a bootable SD card for Atmel Xplained boards.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use genimage to generate a sd card with a fat partition (at91bootstrap,
u-boot, kernel, dtbs) and an ext4 partition (rootfs).
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use genimage to generate a sd card with a fat partition (at91bootstrap,
u-boot, kernel, dtbs) and an ext4 partition (rootfs).
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use genimage to generate a sd card with a fat partition (at91bootstrap,
u-boot, kernel, dtbs) and an ext4 partition (rootfs).
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Let's rework the board and config files to use genimage
to generate the SD card image directly.
[Peter: add host-mtools for genimage vfat handling]
Signed-off-by: Ezequiel García <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
These three are Zynq boards and the build procedure is almost the
same. Having the SoC name prefix "zynq_" would be more consistent.
Also, this is the way in which the Linux Device Trees and the U-Boot
configuration files do.
This commit renames as follows:
zedboard_defconfig -> zynq_zed_defconfig
microzed_defconfig -> zynq_microzed_defconfig
xilinx_zc706_defconfig -> zynq_zc706_defconfig
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It's useful for demo configs which have more features, like
automatically loaded (module) drivers.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
There were two readme files (one for flashing on NAND and one to create a
SD card) in different places. Merge them and update the SD card
generation part since all Xplained boards are supported and the -u
option of sfdisk is obsolete on latest versions.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
[Thomas: adjust the explanations, move the SD card section after the
NAND flash section.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Ethernet is not working, but at least you get a shell and
can test applications for m68k.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
arm_versatile kernel defconfig updated to deal with multi-platform ARM
support and driver changes.
mips(el) 32-bits is back in working order for 4.5
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.5 2.3.0 YES OK
arm_versatile 4.5 2.3.0 YES OK
arm_vexpress 4.5 2.3.0 YES OK
microblazebe 4.5 2.3.0 YES OK
microblazeel 4.5 2.3.0 YES OK
mips64el_malta 4.5 2.3.0 YES OK
mips64_malta 4.5 2.3.0 YES OK
mipsel_malta 4.5 2.3.0 YES OK
mips_malta 4.5 2.3.0 YES OK
ppc_g3beige 4.5 2.3.0 YES OK
ppc_mpc8544ds 4.5 2.3.0 YES OK
ppc_virtex_ml507 4.5 2.3.0 NO OK
ppc64_pseries 4.5 2.3.0 YES OK
sh4 4.5 2.3.0 YES OK
sh4eb 4.5 2.3.0 NO (1) OK
sparc_ss10 4.5 2.3.0 YES OK
sparc64_sun4u 4.5 2.3.0 YES OK
sparc_sun4u 4.5 2.3.0 YES OK
x86 4.5 2.3.0 YES OK
x86_64 4.5 2.3.0 YES OK
xtensa_lx60 4.4.5 2.3.0 YES (2) OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - xtensa ethernet broken in 4.5 so stick to 4.4.x
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
* add a post-image.sh script
* update defconfig for genimage
* update readme.txt
[Peter: also add host-dosfstools dependency for vfat partition]
Signed-off-by: Phil Eichinger <phil@zankapfel.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
We're not trying to be minimal here, and qemu can bridge/emulate certain
usb devices, so enable the different controllers and at least usb
storage.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
We're not trying to be minimal here, and qemu can bridge/emulate certain
usb devices, so enable the different controllers and at least usb
storage.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
mxs-bootlets broke somewhere in between toolchain version bumps, leading to
boot failure.
Directly boot u-boot, as this is supported now, but it requires updated
partitioning (see readme.txt)
Drop mxs-bootlets patches, they aren't needed anymore.
Kernel is built as an uImage because the u-boot defconfig expects an
uImage on the second partition.
Tested on iMX233-OLinuXino-MINI hardware.
[Peter: adjust readme/config as suggested by Arnout]
Signed-off-by: Phil Eichinger <phil@zankapfel.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
It didn't make sense to keep the U-Boot scripts and post build/image
scripts under the nitrogen6x folder since they apply for all our
platforms.
Also update the readme.txt to make it clearer which defconfig should
be used depending on the platform targeted.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Also remove useless tfp410 enablement since a basic kernel driver has
been added.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump to the latest kernel with DT path adjustment because Linux
commit ca5b34100c57 ("dts, arm64: Move dts files to vendor subdirs")
moved the DT file to the vendor sub-directory.
This commit was tested with the latest model (FVP v8 Foundation
Platform 9.5 build 41), so I updated the instruction in readme.txt
corresponding to it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
VFPv3 and NEON was enabled and a readme.txt file was added.
Fixes bug #7580.
Tested on Pandaboard ES.
[Peter: use EABIhf]
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Now that all the boards have been converted to use genimage, the old
instructions on how to partition and write an SD card are useless.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Commit b3fa8e24 (configs: remove calao_snowball_defconfig) dropped the
outdated snowball defconfig, but forgot to remove the board files.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit adds basic configuration files for the Firefly RK3288 board.
Both minimal and demo defconfigs are added. The latter enables Qt5 with
the required Mali T76X GPU user space components.
More info about the board:
http://en.t-firefly.com/en/firenow/firefly_rk3288/specifications/
[Peter: use same-as-kernel for kernel headers]
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch adds a minimal working configuration for
Acmesystems Arietta g25.
[Peter: fix whitespace, use same-as-kernel for kernel headers version]
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As a followup to http://patchwork.ozlabs.org/patch/548550/ fully convert
the versatile defconfig to create the dtb and update the instructions.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This config has no prospect of going into the future (by using DTS), and
qemu doesn't do a good job at emulating it (networking problems), so
drop it.
All of the ARM SMP testing duties are now in the vexpress defconfig
which is better suited/supported.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We can use the vexpress arm defconfig to test SMP features in Qemu.
So document the necessary invocation changes to account for this, in
preparation of the arm nuri defconfig removal.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Keep arm_nuri on 3.10.x for the usual reasons.
Keep mips & mipsel (32 bits) on 4.3.x because 4.4.x fails to boot
properly (kernel stuck after the CPU cache info).
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.4.1 2.3.0 YES OK
arm_nuri 3.10.96 2.3.0 YES(1) OK most times(2)
arm_versatile 4.4.1 2.3.0 YES OK
arm_vexpress 4.4.1 2.3.0 YES OK
microblazebe 4.4.1 2.3.0 YES OK
microblazeel 4.4.1 2.3.0 YES OK
mips64el_malta 4.4.1 2.3.0 YES OK
mips64_malta 4.4.1 2.3.0 YES OK
mipsel_malta 4.3.5 2.3.0 YES OK (4)
mips_malta 4.3.5 2.3.0 YES OK (4)
ppc_g3beige 4.4.1 2.3.0 YES OK
ppc_mpc8544ds 4.4.1 2.3.0 YES OK
ppc_virtex_ml507 4.4.1 2.3.0 NO OK
ppc64_pseries 4.4.1 2.3.0 YES OK
sh4 4.4.1 2.3.0 YES OK
sh4eb 4.4.1 2.3.0 NO(3) OK
sparc_ss10 4.4.1 2.3.0 YES OK
sparc64_sun4u 4.4.1 2.3.0 YES OK
sparc_sun4u 4.4.1 2.3.0 YES OK
x86 4.4.1 2.3.0 YES OK
x86_64 4.4.1 2.3.0 YES OK
xtensa_lx60 4.4.1 2.3.0 YES OK
(1) - Supposed to work but broken, probably Qemu emulation issue
(2) - In like 1/3 starts it fails to work properly
(3) - Probably an endian issue with 8139 emulation/driver
(4) - Kernel stuck at cpu cache details from 4.4 - 4.4.1
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The file that is actually produced is called u-boot-spl.bin, not
uboot-spl.bin.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Juno ARM Development Platform (ADP) is a software development
platform for ARMv8-A, it includes the Juno Versatile Express board
and an ARMv8-A reference software port available through Linaro.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also updating the documentation with the dd instruction to flash the
bootable media.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Peter: use tarball for Linux kernel, use 4.4 kernel headers]
Signed-off-by: Eelco Chaudron <echaudron@xiot.nl>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This is the 21st century, so enable SMP for them.
[Peter: add note to readme.txt about how emulate a SMP system in QEMU]
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Update the raspberrypi and raspberrypi2 configs to use genimage directly
to build the image.
Update the documentation to reflect this, and drop the volatile rootfs
option since it doesn't make much sense and it's not easily integrated
with the genimage configurations.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch updates the Cubieboard2 board defconfig to use newer u-boot
and linux versions, along with a few other improvements.
The other improvements were mostly backported from the recent Orange Pi
defconfig inclusion and are related to image generation.
linux-sunxi.org was used as a reference for both linux and u-boot
defconfig names.
In detail:
- Update linux to vanilla upstream -- currently 4.3.3 is the most
up-to-date. Although it lacks some features present only in the
linux-sunxi 3.4 branch, upstream support appears to be relatively mature
and is already being deployed by default by distributions such as Arch
Linux ARM.
- Update u-boot to vanilla upstream 2015.10. According to
linux-sunxi.org, upstream fully supports major functions (except NAND)
since 2015.07.
- Change image format to zImage and drop custom image generation script
in favour of genimage, as pointed out by reviewers in the Orange Pi
defconfig submission.
This was tested in a Cubieboard2 board with boot from mmc and it boots
fine to login prompt.
This has not been tested in a Cubieboard (A10) as I don't own any; the
version bumps probably apply to it although there are some differences
(lack of VFPv4 support, Cortex-A8 instead of Cortex-A7), so I have kept
the current Cubieboard defconfig and its scripts. This one has been only
build-tested.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit adds a configuration for the Orange Pi PC board,
<http://www.orangepi.org/orangepipc/>.
Signed-off-by: Eelco Chaudron <echaudron@xiot.nl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Documentation is referring to nandflash.txt which doesn't exist.
Instead, readme.txt provides the instructions to flash the NAND storage.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Specify that the drive image file format is raw to avoid warnings and
restrictions.
Also switch to -drive syntax for all configs.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The arm_foundationv8_defconfig currently doesn't build because it uses
an external AArch64 toolchain that has been updated (Linaro toolchain)
and is now based on gcc 5.x. Unfortunately, Linux 3.13 is too old to
be built with gcc 5.x.
As a minimal fix to make this defconfig build again, we switch to use
the internal toolchain backend. At the time this defconfig was
introduced, there was no support for AArch64 in the internal toolchain
backend, but now that it is available, there is no reason to not use
it. This makes the defconfig also more consistent with the other
defconfigs.
Obviously, the kernel headers used to build the toolchain are set to
the fixed version 3.13, so that they match the kernel being used.
While we're at it, the readme.txt file corresponding to this defconfig
is updated. Runtime testing has been performed with the latest version
of the ARM Foundation model.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Created a readme.txt for the Intel Galileo Gen 1/2 that describes,
* How to build for the Intel Galileo Gen 1/2
* How to access the console on the Intel Galileo Gen 1/2
Signed-off-by: Ray Kinsella <ray.kinsella@intel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Board support package includes:
* Toplevel build root configuration
* Github based 3.8.7 Kernel
* Upstream 3.8.7
* Linux 3.8.7 Kernel Driver Patches
* Linux 3.8.7 configuration
* Grub configuration
* Init Script to load modules
* genimage config to create sdcard image.
[Thomas: simplify post-image script since there is now only one call
to genimage.]
Signed-off-by: Ray Kinsella <ray.kinsella@intel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It contained a typo that prevented the driver from being built.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Now that uclibc-ng was bumped to version 1.0.9 nothing prevents x86
from working correctly.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
By default, with the original patch bootcmd runs sdboot before loading uEnv.txt.
Consequently, if the user change modeboot, the user's defined content is updated
too late.
By loading uEnv.txt before 'run $modeboot' the correct boot mode is used instead
of default mode.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
Acked-By: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
ppc-mpc8544ds: switch to custom kernel config since the new 4.3-shipped
mpc85xx_basic_defconfig doesn't work with Qemu.
Incidentally while cleaning it up it now seems to work fine with newer
qemu versions.
sparc64_sun4u: ditch ne2k driver since it's useless, and add the e1000
driver which works fine.
x86: stick to 4.2.x kernels since 4.3 doesn't work right with uclibc
(any variant) based toolchains.
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.3 2.3.0 YES OK
arm_nuri 3.10.93 2.3.0 NO(1) OK(2)
arm_versatile 4.3 2.3.0 YES OK
arm_vexpress 4.3 2.3.0 YES OK
microblazebe 4.3 2.3.0 YES OK
microblazeel 4.3 2.3.0 YES OK
mips64el_malta 4.3 2.3.0 YES OK
mips64_malta 4.3 2.3.0 YES OK
mipsel_malta 4.3 2.3.0 YES OK
mips_malta 4.3 2.3.0 YES OK
ppc_g3beige 4.3 2.3.0 YES OK
ppc_mpc8544ds 4.3 2.3.0 YES OK
ppc_virtex_ml507 4.3 2.3.0 NO OK
ppc64_pseries 4.3 2.3.0 YES OK
sh4 4.3 2.3.0 YES OK
sh4eb 4.3 2.3.0 NO(1) OK
sparc_ss10 4.3 2.3.0 YES OK
sparc64_sun4u 4.3 2.3.0 YES OK
sparc_sun4u 4.3 2.3.0 YES OK
x86 4.2.6 2.3.0 YES OK(3)
x86_64 4.3 2.3.0 YES OK
xtensa_lx60 4.3 2.3.0 YES OK
(1) - Supposed to work but broken, probably Qemu emulation issue
(2) - In like 1/3 runs it fails to start properly
(3) - linux 4.3.0 doesn't like uclibc-based toolchains (net issues)
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The i.MX6 SoloX SABRE board for smart devices is Freescale's reference design
board based on the heterogeneous ARM Cortex-A9 + Cortex-M4 i.MX6 SoloX
applications processor.
This defconfig is inspired from previous freescale_imx6*sabresd_defconfig, and
is based on Freescale "official" git repo on git.freescale.com and SW release
3.10.53_1.1.0_ga.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Gary Bisson <bisson.gary@gmail.com>
Cc: Jérôme Pouiller <jezz@sysmic.org>
Cc: Gilles Talis <gilles.talis@gmail.com>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Virtualizer Development Kit (VDK) Family for ARM Cortex Products
consists of a set of virtual prototypes that provide a virtualizer for
the ARM core variants. The VDK is a standalone package that runs on an
host computer.
[Thomas: drop the following options, which as noted by Arnout, are not
needed:
- BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
- BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="Image"
- BR2_PACKAGE_BUSYBOX_SHOW_OTHERS=y.]
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also revamp the kernel config a bit to make it more featured, enabling
SATA ports and storage.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Enable the generic hda (sound) codec, necessary for qemu audio to work.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Enable the generic hda (sound) codec, necessary for qemu audio to work.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Changes:
* Update Kernel and U-Boot to the latest 2.0.6 BSP release from the
official sources.
* Add genimage config to create bootable SD card image
Signed-off-by: Gergely Imreh <imrehg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
"/usr/bin/env bash" is used everywhere else in host tools. These are the
only remaining offenders.
Signed-off-by: Bjørn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-boot version to 2015.07 from the mainline repository. Since there
is SPL support for the wandboard in the U-boot 2015.07, it is now
possible to boot the same U-boot image for all wandboard variants
(solo/dual/quad).
Bump kernel version to 3.14.28_1.0.0 from the wandboard git repository.
Tested on Wandboard Solo, Wandboard Dual and Wandboard Quad.
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Barebox, AT91Bootstrap and Linux patches for the Calao QIL A9260
board are all located in the same directory, board/calao/qil-a9260/,
with only a prefix to indicate to which component they apply.
Unfortunately, since commit 0eba4759fa
("packages: apply custom patches using *.patch instead of
<pkg>-*.patch"), the logic to apply custom patches in Barebox and
AT91Bootstrap has been changed from applying <package>-*.patch to
applying *.patch (in order to be consistent with what we do for all
packages in Buildroot).
However, this had the effect of trying to apply both the AT91Bootstrap
and Barebox patches on both packages, which obviously cannot work.
This commit fixes that by moving patches around, and switching to use
BR2_GLOBAL_PATCH_DIR for all of Barebox, AT91Bootstrap and Linux
patches.
In addition, the defconfig was not specifying explicitly which Barebox
version to use, so right now it's trying to use Barebox 2015.09, on
which the board-specific patch does not apply. So we've forced to use
Barebox 2012.08, which was the lastest release available at the time
the defconfig was initially contributed.
Cc: Gregory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Both the Barebox and AT91Bootstrap patches for the Calao USB A9G20
board are located in the same directory, board/calao/usb-a9g20-lpw/,
with only a prefix making a difference between whether they apply to
Barebox or AT91Bootstrap.
Unfortunately, since commit 0eba4759fa
("packages: apply custom patches using *.patch instead of
<pkg>-*.patch"), the logic to apply custom patches in Barebox and
AT91Bootstrap has been changed from applying <package>-*.patch to
applying *.patch (in order to be consistent with what we do for all
packages in Buildroot).
However, this had the effect of trying to apply both the AT91Bootstrap
and Barebox patches on both packages, which obviously cannot work.
This commit fixes that by moving patches around, and switching to use
BR2_GLOBAL_PATCH_DIR.
Cc: Gregory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to fetch its kernel source code and U-Boot source
code from gitorious.org, which is not longer available. Therefore,
this defconfig has been failing to build since quite some time. Since
there's no obvious other place to grab the kernel and u-boot source
code, and the defconfig was not updated since a long time, let's
simply get rid of it.
[Peter: also drop README]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
It is based on olimex_a20_olinuxino_lime configuration. Tested on the mainline
kernel 4.1.4. It boots and the Ethernet is working at speed 1 Gbps.
[Thomas: remove ccache and optimize 2 options.]
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Acked-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Linux kernel 4.2 was finally released, so bumping from 4.2-rc5 to
final release.
Updating Linux headers to 4.2 branch since they are introduced in
Buildroot as well already.
Also adding 1 back-ported patch that makes SD/MMC cards usable on AXS
boards. This patch will be a part of 4.3 (already in linux-next) and
hopefully will make its way in 4.2.1.
Once that patch appears in 4.2.x it can be removed from here.
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Those scripts will support coming platforms such as iMX6SoloX or
iMX6QuadPlus.
One important change is that the bootscript now relies on U-Boot to
make the display detection in order to simplify the script.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Changes are based on Zedboard: Xilinx does not provide a specific DTS
for Microzed in the kernel tree. It is suggested [1] to use the
zynq-zed.dts and change the RAM size
[1] https://forums.xilinx.com/t5/Embedded-Linux/Microzed-default-device-tree-dts/td-p/432856
[Thomas:
- extend readme.txt to indicate why the same DTB is used for Microzed
and the Zedboard.
- add a description + Signed-off-by line in the
0001-zynq-Create-microzed-specific-U-Boot-environment.patch, by
re-using the description of the same patch for the Zedboard.]
Signed-off-by: Davide Viti <d.viti@infosolution.it>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The AXS10x Platform consists of a DesignWare AXC001 CPU
Card (with ARC 770D core) in case of AXS101 or AXC003 CPU Card
(typically with ARC HS38 core) in case of AXS103 mounted on an
ARC Software Development Platform Mainboard with DesignWare peripherals:
* SD/MMC contoller
* Gigabit network contoller
* Serial ports (8250-compatible)
* USB 2.0
* SPI
* I2C
It also houses HDMI output for external monitor connection.
For stand-alone usage of the board (with only keyboard, mouse and montor
attached) kernel console and getty made available on tty0 as well as on
serial port (ttyS3).
Note there're 2 prerequisites:
[1] u-boot: 2015.07 - fix creation of .config
http://patchwork.ozlabs.org/patch/502558/
[2] binutils: fix buildng of Linux kernel for ARCv2 ISA
http://patchwork.ozlabs.org/patch/503550/
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The U-Boot v2015.07 is required for successful out-of-the-box
build for common Xilinx Zynq boards (including Zedboard).
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is a Xilinx Zynq (xc7z045) development board, based on Xilinx Zynq
(xc7z045).
This support is based on Avnet Zedboard defconfig/readme.
[Thomas:
- minor fixes in the readme.txt
- rename defconfig from zc706_defconfig to xilinx_zc706_defconfig.]
Signed-off-by: Jordi Montagne <jordi.montagne66@gmail.com>
Tested-by: Jean Burgat <jeanburgat33@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch changes the U-Boot's default environment to
boot Zedboard out-of-the-box from SD card.
The sdboot procedure tries to load a file system.bit into
the Zynq's PL (only if it exists). It is also possible to
alter the booting by an uEnv.txt file located on your SD card.
The uEnv.txt is a plain text file with <key>=<value> pairs
one per line.
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch adds a genimage config file and a post-image script for the
Wandboard, to generate a medium image "sdcard.img", ready to be booted.
The image contains the layout explained in the board readme.txt file:
U-Boot, its environment, and an Ext2 rootfs partition.
The defconfig has been slightly changed to enable this feature. Also
lighten the readme file since the config file is documented and simpler.
Tested on a Wandboard Solo.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: change the name of the tmp dir, and remove it before using
it.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is largely the same as altera_sockit_defconfig.
It uses a fresher Linux and u-boot than SocKit. It also speeds the
serial port up to 115200.
The post-image script is generalized by adding
BR2_ROOTFS_POST_SCRIPT_ARGS and moving it up the altera directory.
Similarly, the readme is moved up and made more generic.
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Those scripts are executed by u-boot in order to detect the hardware
configuration (board, displays etc...), configure the bootargs and
device tree accordingly or update the bootloader located in NOR flash.
This update is necessary due to the kernel bump to version 3.10.53.
The rework consists of replacing the binaries by their text file
equivalent and generate the binaries from the post-build.sh script.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Allows for nicer framebuffer emulation under Qemu with the QXL xorg
driver.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is a set of patch to add support for warpboard
(Freescale board based on imx6sl)
The patch contains :
- defconfig for warpboard
- linux patches from Fabio Estevam to fix device tree due to last change on
warpboard schematics (rev 1.12) and to fix kernel imx_v6_v7 defconfig which
use incorrect hci protocol
- specific firmware file for warpboard bluetooth
nvram : brcmfmac4330-sdio.txt
Origin of nvram config file for wifi :
https://github.com/Freescale/meta-fsl-arm-extra
[Thomas: misc rewording/improvements in the README file.]
Signed-off-by: Arthur LAMBERT <arthur@dreem.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add a defconfig for the Olimex A20-OLinuXino-Micro board, reusing most
of the A20-OLinuXino-Lime files.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The files in board/olimex/a20_olinuxino_lime/ work with minimal or no
modifications for the Olimex A20-OLinuXino-Micro board, whose support is
going to be added in a later commit.
Rename the directory to clarify it's not restricted to the Lime anymore.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Explicitly state where this information comes from.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Provide a flashing helper to properly select the sam-ba configuration
and reuse the sam-ba tcl script provided by Atmel with minimal
modifications.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
For consistency, rename atmel_xplained_defconfig to
atmel_sama5d3_xplained_mmc_defconfig as this configuration supports
booting the sama5d3 Xplained with an MMC card (as opposed to the NAND
flash).
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Now that we have a sanitised set of defconfig files, and we no longer
support non-DT setups, update and simplify the board readme file.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Floris Bos <bos@je-eigen-domein.nl>
Cc: Pascal de Bruijn <pmjdebruijn@pcode.nl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update to the latest stable kernel version; build an in-tree DTB; use
a in-tree defconfig; enable C++ (to match what we have in the non-DT
variant); do not install DTB overlays (this minimalist config does not
make use of them).
Generate the DTBs for both the "original" variant (A and B) and the
"Plus" variant (A+ and B+).
Drop our custom linux defconfig file now we use an in-tree one.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Floris Bos <bos@je-eigen-domein.nl>
Cc: Pascal de Bruijn <pmjdebruijn@pcode.nl>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit adds a new defconfig for the Olimex A20 OLinuxino Lime
board, based on the 3.4.x vendor specific kernel, which allows to use
the Mali 3D acceleration for OpenGL support.
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit adds a new defconfig for the Olimex A20 OLinuxino Lime
board, based on the 4.x mainline kernel.
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update most of the configs to the latest kernel version (4.1) except for
arm-nuri which is stuck.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Enable USB UHCI to be able to use usb mouse emulation for graphic
application tests.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The VIA VAB-820 board (and the AMOS-820 system built around it) is
based on Freescale i.MX6 for embedded and industrial computing.
Signed-off-by: Gergely Imreh <imrehg@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
- Update kernel
- Add u-boot configuration
- 6q_bootscript.txt is no more needed by new version of u-boot
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
[build test only]
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch to kernel 4.0.
Enable evdev for extra X testing.
Drop bloat/redundant options.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch to kernel 4.0.
Enable evdev for extra X testing.
Drop bloat/redundant options.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch to kernel 4.0.
Use a custom kernel config to avoid the caveat of a huge debug-enabled
one.
And also reduce defconfig options to avoid bloat.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch to kernel 4.0.
Switch kernel config to ext4, simplify to reduce bloat.
Adjust invocation to keep the framebuffer window for graphics testing.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch to kernel 4.0.
Switch to DTB (mandatory).
And adjust invocation to use dtb and add a little more RAM for testing.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch to kernel 4.0.
Remove redudant/pointless kernel options to reduce bloat.
Switch from smc9111 to rtl8139 for networking because of issues.
Enable evdev support for better x11 testing.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Thomas: fix issues noticed by Arnout:
- Rewrap the linux/Config.in paragraph
- Revert the "is a toolchain dependency" -> "has a toolchain
dependency" change from pkg-generic.mk, as the original was
correct.]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Document the correct defconfig for ARMv7 based RPi-2.
Cc: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The i.MX28 Evaluation Kit (or EVK) is Freescale's evaluation board based on the
i.MX287 Applications Processor.
This defconfig is based on mainline u-boot and Linux kernel.
Also, we add an SD card creation script and documentation, shamelessly based on
the ones for i.MX5/6 by Luca Ceresoli.
[Arnout: fixate U-Boot and kernel (headers) versions]
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
SABRE Board for Automotive Infotainment (SABRE Auto, a.k.a. SABRE-AI) is
Freescale's evaluation board based on the i.MX 6 ARM Cortex-A9 applications
processor.
Those defconfigs are an adaptation of freescale_imx6{q,dl}sabresd_defconfig for
SABRE Auto, and are thus based on Freescale "official" git repo on
git.freescale.com and SW release 3.10.17_1.0.0_ga.
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Gilles Talis <gilles.talis@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Gary Bisson <bisson.gary@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Rename imx6sabresd board folder to imx6sabre, to prepare for Sabre Auto
addition. Update doc, link and defconfigs accordingly.
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Gilles Talis <gilles.talis@gmail.com>
Cc: Gary Bisson <bisson.gary@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The i.MX31 Product Development Kit (or PDK) is Freescale development board
based on the i.MX31 application processor.
This defconfig is based on mainline kernel v3.15.10, and is aimed at a PDK in
"3 stack" configuration, with CPU engine board, personality board and debug
board.
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The RPi-2 has its own DTB, so document it in the list of generated
files.
Also, not all DTBs need to be present on the boot partition, so add a
comment that identifies which should be copied for each model.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is a small development board, based on Freescale IMX6 Solo SoC
(single core ARM Cortex-A9). The board has excellent support in mainline
U-Boot and Linux.
Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update configuration to use the 3.18.8 kernel and update U-Boot to
2015.01. With the switch to 2015.01. use the U-Boot SPL image for the
first stage bootloader instead of the at91bootstrap. The U-Boot SPL
requires that the U-Boot image format be u-boot.img in order to load
from the SD card.
Signed-off-by: Ryan Barnett <ryanbarnett3@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
qemu_arm_vexpress_defconfig is broken for 3.19 so keep it with 3.18.x
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The instructions for the Raspberry Pi 2 (aka model B2) are the same as
the ones for the Raspberry Pi, so:
- state so in the existing readme
- create a symlink raspberrypi2 -> raspberrypi
Also fix typo in spelling of "Raspberry Pi" (two words, not one).
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
the loaduimage command was renamed to loadimage when the default kernel
image changed from uImage to zImage in u-boot commit e3cf9692053a, which
made it into the v2013.10 u-boot release that the beaglebone_defconfig
currently builds.
Signed-off-by: Vanya Sergeev <vsergeev@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The rootfs.tar file is located under ./output/images/.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is an example of a Device-Tree-enabled Raspberry Pi defconfig.
We have to use a 3.18-based kernel for that, but there are a few
limitations:
- we can not use the minimalist RPi defconfig bundled with the kernel,
namely bcmrpi_quick_defconfig, because it is not DT-enabled, and
sets CONFIG_ARM_PATCH_PHYS_VIRT to 'n', which prompts a value for
CONFIG_PHYS_OFFSET, as it as no default for the bcm familly;
- most importantly, the rpi-3.18.y branch is constantly rebased, so
there is no guarantee that the sha1 I use today will still be usable
in the long term. Using the name of hte branch is not better either.
So, we bundle our own DT-enabled linux defconfig that is based on
bcmrpi_quick_defconfig, with just CONFIG_ARM_PATCH_PHYS_VIRT set and the
Device TRee enabled.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Those files were previously installed, but that's no longer the case
since we select in the menuconfig which version of the bootloader we
install.
[Thomas: fix minor typo in commit log.]
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Used to test the new default binutils 2.24 (all passed).
Also update the virtex readme since the dtb is in output/images as well.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
MIPS Creator CI20 is a Linux and Android development system from
MIPS/Imagination Technologies. It incorporates an Ingenic JZ4780 SoC
which includes a 1.2GHz dual core MIPS32 processor and Imagination
PowerVR SGX540 GPU.
More information can be found at:
http://elinux.org/MIPS_Creator_CI20
Signed-off-by: Vicente Olivert Riera <Vincent.Riera@imgtec.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
in order to not depend on the previous permissions of each file
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Since the apf9238 support is in the mainline kernel, we can bump to
kernel 3.17.2.
The patches can be removed because:
- linux-3.1.1-0001-fixes_arm_mach-types_for_apf9328.patch is no
longer needed, since the machine number for apf9328 is now
upstream.
- linux-3.1.1-0002-add_missing_config_option_for_apf9328.patch is no
longer needed, because the MTD_CFI_INTELEXT option is selected by
the imx_v4_v5_defconfig.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Very similar to the older Minnowboard, except that it works with mainline
Linux, uses 64bit firmware and a realtek NIC needing firmware.
The Linux configuration is based on the configuration fragment on elinux:
http://elinux.org/Minnowboard:MinnowMaxLinuxKernel
Many thanks to Circuitco for sponsoring a board.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Also drop the sparc memset patch, it's upstream as of 3.17.2.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
this script permits the generation of an sdcard that will boot on
and i.MX53 QSB with a recent bootloader (now supported by buildroot).
Tested on an i.MX53 QSB and an i.MX53 QSB-R
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
- Added short readme file with description of first steps how to start.
- Added uEnv.txt so the board can start from SDCard
- Added post-image.sh script to copy included uEnv.txt to output/images
[Peter: strip trailing spaces]
Signed-off-by: Marcin Jabrzyk <marcin.jabrzyk@gmail.com>
Tested-by: Stephan Hoffmann <sho@relinux.de>
Tested-by: Marcin Jabrzyk <marcin.jabrzyk@gmail.com>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Enable TMPFS support for our custom qemu kernel configs, it's generally
used and can lead to failures/confusion.
Moreover enable ACL & XATTR TMPFS support for SystemD.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The audio patch has not been upstreamed and no longer applies.
[Peter: explain why patch is dropped]
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The support for the TS-5400 platform is mainlined since Linux 3.17.
This commit removes the outdated support patch and bumps the kernel
headers (and thus Linux) to 3.17.x.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Update to Linux Kernel 3.16.3.
Enable Ext4 by default.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The best practice is to use the BR2_GLOBAL_PATCH_DIR for patches against
U-Boot, not BR2_TARGET_UBOOT_CUSTOM_PATCH_DIR.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Tested-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Gilles Talis <gilles.talis@gmail.com>
Cc: Gary Bisson <bisson.gary@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
To the 2014.07 release. For furture details, see:
http://boundarydevices.com/u-boot-2014-07-release-mx6-boards/
Also update our 6x_upgrade script to the version from that page so the
entire SPI flash gets erased (otherwise it fails on big u-boot builds) and
document how to perform the upgrade.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
u-boot fixup
Update Linux Kernel to 3.16.3.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update Linux Kernel to 3.16.3.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update to Linux Kernel 3.16.3.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update to Linux kernel 3.16.3.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update to Linux Kernel 3.16.3.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update config to Linux 3.16.3.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Buildroot supplies a nice /init wrapper script to use when booting from a
ramdisk.
We add a patch to u-boot to tell the kernel to boot into /init (instead of
/linuxrc) on i.MX6, when booting in mfgtools mode. This way we can boot a
buildroot system entirely through USB.
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com
[Luca: rebase on top of iMX6DL patches and patch iMX6DL defconfig as well]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
[Luca: build- and run-tested on i.MX6DL SABRESD]
Tested-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Gary Bisson <bisson.gary@gmail.com>
Cc: Thomas De Schampheleire <patrickdepinguin+buildroot@gmail.com>
Cc: Gilles Talis <gilles.talis@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Document how to create a bootable SD card for the two supported SABRESD cards:
i.MX6Q and i.MX6DL.
The SD card creation relies on an ad-hoc script.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Gilles Talis <gilles.talis@gmail.com>
Cc: Gary Bisson <bisson.gary@gmail.com>
Cc: Vincent Stehlé <vincent.stehle@freescale.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
With the kernel patch from:
http://patchwork.ozlabs.org/patch/384285/
There is no problem with latest gcc anymore.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update the default configuration to use Linux 3.15.x.
Enable ext4, so that ext2/ext3/ext4 can be used.
Tested with Qemu 2.0.0.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update defconfig to 3.15, tested with Qemu 2.0.0.
Removed hint about framebuffer, as -display none is used.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update to 3.15.x, remove ext3 support, use ext4 as
default.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update to 3.15.x, disable ext3, use ext4 as default.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
In English, unlike in French, almost all usages of the word 'information'
are uncountable, meaning that 'informations' is invalid.
This patch fixes this typo throughout the tree, except in CHANGES and
docs/news.html (historic text).
Signed-off-by: Thomas De Schampheleire <thomas.de.schampheleire@gmail.com>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Result tested with Qemu 2.0.0 without issues.
Old SCI problems are fixed in Qemu.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested with Qemu 2.0.0.
Overlay is from
https://github.com/jcmvbkbc/xtensa-toolchain-build/tree/master/overlays
Many thanks to Max Filippov <jcmvbkbc@gmail.com> for his extended help
and kernel config examples.
A small kernel patch is required, because mkimage does not contain
support for Xtensa and the uImage target is failing. Redboot is unused
so disable it, too.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch adds support for the TS-5x00 serie of Technologic Systems
x86-based Single Board Computers, featuring an AMD Elan520 processor.
http://wiki.embeddedarm.com/wiki/#AMD
[Peter: explicitly set arch/variant in defconfig, strip trailing spaces]
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add support for the iMX6 based conga-QMX6 family of Qseven modules.
This patch is based on Linux 3.0.35 from Congatec's kernel reporitory
[Peter: slightly simplify post build script]
Signed-off-by: Stephan Hoffmann <sho@relinux.de>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add initial support for the Lego Mindstorms EV3 programmable brick.
The Lego Mindstorms EV3 brick comprises a Texas Instruments AM1808 SoC, with
an ARM 926EJ-S main processor running at 300 MHz.
https://en.wikipedia.org/wiki/Lego_Mindstorms_EV3
This configuration uses the Linux kernel of the ev3dev project.
https://github.com/mindboards/ev3sources
More info is available in the board/lego/ev3/readme.txt file, shamelessly
documented in the same way as the SoCkit folks did.
[Peter: lock kernel headers to match]
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump zedboard defconfig to version 2014.1. This makes it possible to use
uboot-spl instead of the xilinx specific fsbl. However, the result is kinda
hacky due to the licensing state of ps7_init.{c,h} needed for building uboot
spl. Directions for building a proper boot.bin using the new methodolgy is
included in the readme.txt.
Signed-off-by: Spenser Gilliland <spenser@gillilanding.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Make ti-gfx working on BeagleBone Black by adding an ugly necessary
patch to the kernel wich fix:
pvrsrvkm: Unknown symbol v7_dma_map_area
pvrsrvkm: Unknown symbol v7_dma_flush_range
Add drivers to the default kernel config used in beaglebone_defconfig
to enable the framebuffer.
Signed-off-by: Hadrien Boutteville <hadrien.boutteville@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The alsa utils packages require a kernel with IPC support to run. The
kernel config for the x86 and x86_64 qemu build includes sound support
using the hda driver but without the IPC support the alsa utils won't work.
This patch adds IPC support to the x86 and x86_64 kernel to allow alsa
utils to run and brings the kernel config inline with kernel configs for
other qemu boards.
Signed-off-by: Martin Bark <martin@barkynet.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
- fix networking in Qemu using a small patch
- disable DTS, because linux.bin does not include any DTB the
default Qemu included DTB is used and this is okay and works fine
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Acked-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Tested-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Config name has changed.
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit updates the defconfig of the foundation-v8 platform, which
can be tested under the AArch64 emulator provided by ARM. The main
change is that we switch to the mainline 3.13.6 kernel instead of a
Linaro-specific Git tree.
Another change is to update the download link for the emulator in the
instructions, in order to use the latest version of the emulator,
which was used for testing.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Tweak the config to deal with b155f5a5ab
fallout.
And bump to the latest kernel versions.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tweak the configs to deal with b155f5a5ab
fallout.
And bump to the latest kernel versions.
As of this commit the microblaze qemu targets seem broken, probably
because of commit 14e527eb66 or some qemu
limitation.
SPARC seems to have issues as well, the kernel seems to go down with an
unhandled exception with qemu 1.7.0
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit introduces initial support for the Arrow SoCkit
boards, featuring an Altera Cyclone V SoC:
http://www.altera.com/b/arrow-sockit.html
It is based on Roman Diouskine's work at
https://github.com/rndi/buildroot-alt.
The kernel and the u-boot used is the one developped by the
rocketboards.org community, as mainline support is not fully
available yet.
More info is available in the board/altera/sockit/readme.txt file.
[Thomas: remove a number of not really needed empty new lines in the
readme.txt file, update the defconfig for the new kernel headers
options.]
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
