Bump Linux to 5.10.10 and U-Boot to 2020.10. In the new kernel sunxi-mmc
driver has been switched to asynchronous probe. As a result, mmc indexes
can be shuffled breaking board boot. Add patch that pins mmc indexes to
their original ordered values.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit adds support for Sinovoip's Banana Pi
M1+. It is mostly based on bananapro_defconfig
but with appropriate device tree and minor tweaks:
- apply bananapi-m1-plus device tree in linux
- apply bananapi_m1_plus defconfig for uboot
- apply patch for OOB IRQs on new device tree
- update device tree name in boot.cmd, genimage.cfg
- update symlink for BRCM driver in rootfs_overlay
- overall clean-up of the config
Tested on BPI-M1+ V1_1.
Signed-off-by: Filip Skoneczny <fskoneczny@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
GPT provides partition labels, which can be used to tell the kernel to find
the rootfs based on it (root=PARTLABEL=rootfs) as a nicer/more extensible
solution than the MBR disk signature / PARTUUID.
When using GPT, the name of the partition in genimage.cfg is used as the
label for that partition.
The default GPT partition table location unfortunately conflicts with the
SPL location, so move the 16KB GPT table after it.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
[yann.morin.1998@free.fr: add the comment about 'rootfs']
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The probing order of the two mmc controllers (sdcard and sdio wifi) has
changed in kernel 5.10 since commit 21b2cec61c04bd1 (mmc: Set
PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4), so change to
root=PARTUUID=.. instead of hardcoding /dev/mmcblkXp2.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
[yann.morin.1998@free.fr: use feedc0de as magic]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
HDMI support is enabled by default in sunxi_defconfig since commit
c822a3ec17 (ARM: configs: sunxi: Add DRM output-related options), so drop
from fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Support for this board was removed in Linux upstream [1] since Xilinx
new design tools dropped these platforms in 2013, along with all
PPC405/PPC440 new designs. They are not maintained nor tested anymore.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7ade8495dcfd788a76e6877c9ea86f5207369ea4
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump most QEMU defconfigs (every one that was previously on 5.4.y)
to latest longterm kernel 5.10.7.
Please note the following exceptions/modifications:
- board/qemu/qemu_s390x_defconfig: ignored (already up to date)
- board/qemu/sh4*-r2d:
- Remove the remaining kernel patch [1] provided by Alan Modra
fixing rodata alignment, carried here by Romain Naour [2] to
fix an issue preventing kernel from booting with binutils 2.23.
Patch is present in upstream Linux now.
- Fix compile-time error regarding 64-bit time data structures
from kernel headers when building with uclibc. Previous fix [3]
existed upstream; but see details below.
- board/qemu/ppc-mpc8544ds: Updated kernel patch
- board/qemu/arm-versatile: Updated kernel patch
- board/qemu/mips*r6*: Updated kernel patch
Tested on all configs/qemu* configurations. [4]
[1] https://www.sourceware.org/ml/binutils/2019-12/msg00112.html
[2] https://git.busybox.net/buildroot/commit/?id=a2331c8a61bdd71c47492efc818fb0458a349219
[3] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=fc94cf2092c7c1267fa2deb8388d624f50eba808
[4] https://gitlab.com/clumsyape/buildroot/-/pipelines/244024195
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Integrate the RCW into the storage device image, so the image can also
be used a boot source. The SoC expects the RCW at offset 4096 of the SD
card or eMMC.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Enable building of the bootloader and integrate it into the resulting
image.
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Bump QEMU defconfigs to latest longterm kernel 5.4.88.
Please note that QEMU boards not based on 5.4.y were ignored:
- qemu_csky810_virt_defconfig
- qemu_csky807_virt_defconfig
- qemu_csky610_virt_defconfig
- qemu_csky860_virt_defconfig
Tests were carried out on all QEMU boards using Gitlab [1] (commit
message was slightly different, but the patch is identical)
Additional actions needed were:
- board/qemu/sh4-r2d: Remove one of the two kernel patches [2] provided
by Alan Modra fixing rodata alignment, carried here by Romain Naour [3]
to fix an issue preventing kernel from booting with binutils 2.23.
Patch is present in upstream Linux now.
[1] https://gitlab.com/clumsyape/buildroot/-/pipelines/239483891
[2] https://www.sourceware.org/ml/binutils/2019-12/msg00112.html
[3] https://git.busybox.net/buildroot/commit/?id=a2331c8a61bdd71c47492efc818fb0458a349219
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add the new SAM9X60 Evaluation Kit with linux4sam_2020.04
components. Update README file with new defconfigs.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Re-introduced rock64_defconfig which was dropped by commit
a5fa2469e6 ('Revert
"configs/rock64_defconfig: remove defconfig"').
Signed-off-by: Min Xu <xuminready@gmail.com>
Tested-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
It may be useful for users using Boundary Devices boards to find
more advanced defconfigs that the one provided by Buildroot.
See:
https://github.com/boundarydevices/buildroot-external-boundary#configurations-details
Update the readme.txt to add the link to the br2_external maintained
by Boundary Devices.
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Cc: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Remove the note about non-working network. This was actually fixed with
linux kernel 5.9. This board is now on 5.10.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
weston does not work on the ti-sgx SDK, so switch to using KMS directly,
and drop the wayland-related config options.
Signed-off-by: Adam Duskett <Aduskett@gmail.com>
[yann.morin.1998@free.fr: split into its own patch]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
When tags was added by commit 011206b2bf
to detect the qemu command line, the qemu_arm_vexpress_tz_defconfig
was ignored due to a build issue.
This build issue has been fixed by previous patches, so we can
enable the runtime testing by adding the tag in the readme.txt
and the post-image script in the defconfig.
Since Qemu from HOST_DIR is now executed directly from BINARIES_DIR,
we can remove all the string before "qemu-system-*".
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Usually the qemu command line start directly with "qemu-system-<arch> ...".
But the command line for qemu_arm_vexpress_tz_defconfig start by doing
"cd output/images && ../host/bin/qemu-system-arm". This is necessary
since boot binaries, except BL1, are primarily loaded via semi-hosting
so all binaries has to reside in the same directory as QEMU is started
from [1].
To order to handle this case correctly, update the post-image.sh used
by all qemu defconfigs to execute qemu from BINARIES_DIR.
Since we have to change the current directory use a subshell to
restore the current directory after Qemu execution.
[1] 4ebbea9592/docs/plat/qemu.rst
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The output/images directory is called BINARIES_DIR in the
Buildroot manual, not IMAGE_DIR.
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Bump to the latest kernel v5.9.11 and require openssl.
- Switch to PSCI for bringing up the secondary CPUs.
- Switch to GICv3.
- Update the instruction in the readme.txt to use the latest FVP v8
Foundation Platform 11.12 build 38, and to start 4 cores in SMP.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for Orangepi Zero Plus board:
- U-Boot 2020.10
- Linux 5.7.19
- Default packages from buildroot
This patch is based on Orangepi Zero Plus2 board support, so genimage
configuration and description is copy pasted. One difference is that
newer Linux and U-Boot are selected. Another difference is Ethernet
support (Plus) instead of WiFi (Plus2).
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
For grub-efi we can align the rootfs to start at exactly 16MB from the
beginning of the disk. This can be done by reducing the vfat partition to
be 32 KB smaller than its 16MB size, just like the offset of the vfat
partition.
Signed-off-by: Florian La Roche <Florian.LaRoche@gmail.com>
[Peter: drop redundant offset/size settings, add comment]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As resizing the rootfs partition using a partition manager can result
in a non booting image due to the firmware's location, removal of the
size limit for the rootfs allows better match size-wise.
Signed-off-by: Dagg Stompler <daggs@gmx.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
U-Boot 2020.10 no longer provides boot command in default environment for
Udoo Quad/Dual board. Boot script needs to be added to the image. In order
to keep using common infrastructure for freescale boards, move boot files
to root filesystem and add boot script there. Also switch Udoo Neo board
to common freescale infrastructure to simplify maintenance.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
After BSP update Udoo Quad/Dual board once again hangs on boot. On a
new kernel disabling CONFIG_USB option is not enough to work around
the troublesome usb host on Udoo Quad/Dual board. So in order to be
future-proof it makes sense to disable usbh1 block in device tree
rather than fine-tune kernel configuration after BSP updates.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit changes the stm32mp1 configurations to use the TF-A ->
U-Boot boot flow (called "trusted boot flow" by ST) instead of the
U-Boot SPL -> U-Boot boot flow. ST recommands this trusted boot, and
it's also the only one that allows to use the STM32 Cube Programmer
for reflashing devices.
As part of this, the genimage configuration file is now generated, as
it contains some file names that depend on the platform. Removing
partition-type from genimage.cfg is mandatory, since it would cause a
hybrid MBR partition table to be created, which itself would prevent
ATF from finding the ssbl parition.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Starting with linux kernel v5.9 all required configuration options are
available in the default config.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since 2020.04 version, the enumeration of MMC has changed, so the boot
script must be updated
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the chromebook elm configuration to use v5.9 instead of an
intermediate release candidate.
At the latter stages of the v5.9 release, a patch was added which
broke the Chromebook Elm HDMI. Therefore add a revert patch to get rid
of this problem. The fix (and the revert) are already on the mailing
list (https://lkml.org/lkml/2020/10/10/32) and should become available
with v5.10
Signed-off-by: Bilal Wasim <bilal.wasim@imgtec.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since 52f188140c (qemu version bump to 5.1),
the image generated by qemu_riscv64_virt_defconfig doesn't boot anyore with
the following error:
rom: requested regions overlap (rom phdr #0: [...]/images//fw_jump.elf. free=0x000000008000e240, addr=0x0000000080000000)
qemu-system-riscv64: rom check and register reset failed
Update the qemu command line as described in the Qemu wiki for riscv64 [1]
Fixes:
https://gitlab.com/jugurthaB/buildroot/-/jobs/686104707
[1] https://wiki.qemu.org/Documentation/Platforms/RISCV#Booting_64-bit_OpenEmbedded_Images
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Jugurtha BELKALEM <jugurtha.belkalem@smile.fr>
Cc: Alistair Francis <alistair.francis@wdc.com>
Cc: Mark Corbin <mark@dibsco.co.uk>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
[yann.morin.1998@free.fr:
- don't force network range
- don't forward TCP port
- drop post-build script to add tty1
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This commit adds supports for building buildroot kernel + rootfs
for MT8173 Elm board, also known as Chromebook Elm
(https://www.acer.com/ac/en/US/content/series/acerchromebookr13).
Though Chrome-OS is officially supproted on this board, the
mainline kernel works as well (benchmarks + conformance), and so
the 5.9 kernel is used. As the 5.9 kernel isn't yet released, we
use the 5.9-rc5 for now, which will be up-revd to 5.9 once its
released.
Using the mainline kernel means that we have to apply certain patches
to get the HDMI screen working. These patches are lying in the
"drm-misc-next" list and will make it to the kernel after 5.9. At that
time, we will remove the patches and point Buildroot to use the latest
kernel (hopefully, 5.10).
This commit also adds an ITS file (for creating FIT images), an ARGS
file (for providing kernel args) and a "sign.sh" script to generate
signed kernel images. Though the "sign.sh" is very similar to the
coresponding file under board/chromebook/snow, it cannot be shared
between both boards, as the script requires access to the board
specific its / args file.
Additionally a readme & defconfig is added to help the user get started.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The same script is going to be used by the Chromebook Elm to generate
a bootable SD / USB image. Therefore, move the script out of the snow
folder to one level above (board/chromebook/snow -> board/chromebook).
Update the chromebook_snow_defconfig to reflect the new location of
the script.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for imx8mqevk_defconfig that allows booting a mainline
kernel.
This defconfig still relies on NXP ATF and U-Boot, but in the long term
the plan is to switch to mainline ATF and U-Boot as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Analog audio is enabled by default in sunxi_defconfig since commit 5d2408c6
(ARM: configs: sunxi: Add sun8i analog codec), so drop from fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Now that upstream supports this board add buildroot support for it,
too.
This supports:
- latest upstream linux kernel. Since the support for this board and
its SoC is still in active development, we want to follow the
upstream kernel releases for now.
- building an image which can be installed to eMMC, SD card or USB
thumb drive.
- upstream u-boot patches are pending, therefore no support for
building a bootloader for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Now that RISC-V 32-bit (RV32) support has been merged into mainline
glibc, we can use the Linux 5.4 kernel.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The apu2 by PC Engines is a 64 bit single board computer with coreboot
BIOS. It only has serial output, but no graphics chip. With its 2–4
ethernet ports, it is often used to build a firewall or router.
The provided defconfig configures busybox and isolinux. It will output
a hybrid ISO image that can be written to a USB stick or burned to a
CD.
Configuration based on a blogpost by Tony Arkles:
http://www.better-bsp.com/blog/2017/03/02/buildrooting-for-apu2/
Signed-off-by: Danilo Bargen <mail@dbrgn.ch>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A defconfig for the friendlyarm nanopc-t4 was added in
c23895f06e, but then removed
in 8efd4463f7 because an ARM32
compiler was needed to build ATF, and this was not supported
back then.
Now, since package/arm-gnu-a-toolchain/ has been added, this
defconfig can be re-introduced.
Following new changes are introduced in comparision with the
older changeset:
- updated readme
- GPT partition layout is being used
- update defconfig to build ATF
- bump u-boot to 2020.07
- bump linux to 5.8.2
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: fixate U-Boot version; remove blind BR2_TARGET_UBOOT_NEEDS_PYTHON]
A defconfig for the friendlyarm nanopi-m4 was added in
493c3979a4, but then removed
in a24bd8936f because an ARM32
compiler was needed to build ATF, and this was not supported
back then.
Now, since package/arm-gnu-a-toolchain/ has been added, this
defconfig can be re-introduced.
Following new changes are introduced in comparision with the
older changeset:
- readme updated
- GPT partition layout
- update defconfig to build ATF
- bump u-boot to 2020.07
- bump linux to 5.8.2
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: fixate U-Boot version; remove blind BR2_TARGET_UBOOT_NEEDS_PYTHON]
A defconfig for the rockpro64 was added in
59e1077b4e, but then removed
in 10f49213b7 because an ARM32
compiler was needed to build ATF, and this was not supported
back then.
Now, since package/arm-gnu-a-toolchain/ has been added, this
defconfig can be re-introduced.
Following new changes are introduced in comparision with the
older changeset:
- renamed defconfig from pine64_rockpro64 to rockpro64
- updated readme
- using a GPT partition layout
- update defconfig to build ATF
- bump u-boot to 2020.07
- bump linux to 5.8.2
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: fixate U-Boot version; remove blind BR2_TARGET_UBOOT_NEEDS_PYTHON]
Mainline Linux now has basic s500/roseapplepi support, so switch to that to
get rid of the dependency on gcc7. Add two patches for the dts / fix that
didn't make it for kernel 5.7.
The mainline kernel does not yet have support for the mmc interface, so
change to initramfs for now. Patches for mmc support have been posted
recently, so this can be reverted once they show up in a stable kernel:
https://lore.kernel.org/lkml/cover.1593124368.git.cristian.ciocaltea@gmail.com/
The owl serial port is called ttyOWLn in mainline, so adjust the bootargs to
match. Also drop the unneeded execute permission on uEnv.txt.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for RK3288 SOM based radxa rockpi-n8
target with below features:
- Custom U-Boot 2020.07-rc4
https://github.com/amarula/u-boot-amarula.git
commit: "ba120841bf40ebaed049d64bb4f980083a1cf6b7"
- Custom Linux 5.7.0-rc1
https://github.com/amarula/linux-amarula.git
commit: "5dcb0132685b07beb82065c5d7521e6c555c55b6"
- GPT partition layout is being used
- Default packages from buildroot
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/674933582
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Signed-off-by: Oleksandr G Zhadan <Oleks@ArcturusNetworks.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
