All Buildroot pre-built toolchains have been rebuilt with Buildroot
2017.11-rc1, so that they have the latest version of
glibc/musl/uClibc, and also the latest gcc/binutils updates.
Specifically, this will fix the build failures on Blackfin that were
due to the missing accept4() support:
http://autobuild.buildroot.net/results/8b5a72dd7cde685f6f68f46aeee8b1b60c96d559/
(openobex)
http://autobuild.buildroot.net/results/b19dd9ed29944d7f79c6f824669e3baaa0bb045a/
(libiio)
In terms of changes to the toolchains:
- AArch64 glibc toolchain changed to use 4.4 kernel headers instead
of 4.1, in order to increase the variety of kernel header versions
being tested.
- Most configurations now use 4.13 kernel headers instead of 4.12
(except the configurations that were explicitly using an older
kernel headers version)
- The mips64 n64 configuration is changed from using gcc 4.9 to gcc
5, since another ARM configuration already tests gcc 4.9.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes:
http://autobuild.buildroot.org/results/2af/2af7412846c576089f8596857ab8c81ac31c1bed/
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: André Hentschel <nerv@dawncrow.de>
Reviewed-by: André Hentschel <nerv@dawncrow.de>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Currently, HOSTCC and HOSTCXX are set to their _NOCACHE variants in the
'dependencies' target. This is needed because at that time, ccache is
not built yet - host-ccache is one of the dependencies. However, because
this override is only specified for the 'dependencies' target (and
thereby gets inherited by its dependencies), the override is only
applied when the package is reached through the 'dependencies' target.
This is not the case when one of DEPENDENCIES_HOST_PREREQ is built
directly from the command line, e.g. when doing 'make host-ccache'. So
in that case, ccache will be built with ccache... which fails of
course.
To fix this, directly apply the override to the DEPENCIES_HOST_PREREQ
targets.
Note that this only fixes the issue for 'make host-ccache', NOT for
e.g. 'make host-ccache-configure'.
Signed-off-by: Alfredo Alvarez Fernandez <alfredo.alvarez_fernandez@nokia.com>
[Arnout: improve commit message]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
glibc is now supported for ARC so let's kick-start autobuilders
with glibc toolchain for ARC HS.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Arnout Vandecappelle <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Linux 4.0 kernel doesn't build with gcc 6.x, which is used since
the toolchain update in commit
193dfffa83 ("support/testing: use more
recent toolchains"). So let's update to Linux 4.11 instead (like the
existing Qemu x86 defconfig does), and update the kernel configuration
file accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
With the hard disk crash of autobuild.b.o, we lost old toolchains, so
use the latest toolchains, which have been restored.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Currently, the download directory, when specified with the -d option, is
only used to store the files downloaded by the testing infra, not those
downloaded by Buildroot.
So, we end up with this situation:
BR2_DL_DIR | -d DIR | test downloads | BR downloads
------------+----------+------------------+--------------
unset | unset | [error] | [error]
unset | set | in $(DIR) | in $(TOP_DIR)/dl
set | unset | in $(BR2_DL_DIR) | in $(BR2_DL_DIR)
set | set | in $(DIR) | in $(BR2_DL_DIR)
This is not very consistent.
We change the behaviour so that the value of -d always takes precedence,
and is used by Buildroot as well, giving this new behaviour:
BR2_DL_DIR | -d DIR | test downloads | BR downloads
------------+----------+------------------+--------------
unset | unset | [error] | [error]
unset | set | in $(DIR) | in $(DIR)
set | unset | in $(BR2_DL_DIR) | in $(BR2_DL_DIR)
set | set | in $(DIR) | in $(DIR)
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fix typo 'selectes' -> 'selects'.
Additionally, change 'will exclude' to 'excludes' to align with 'selects'.
Signed-off-by: Thomas De Schampheleire <thomas.de_schampheleire@nokia.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fix the remaining code style warnings from flake8:
- properly indent continuation lines;
- use proper code to test a parameter is not None.
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Fix the trivial warnings from flake8:
- remove modules imported but unused;
- use 2 lines before class or module level method;
- remove blank line at end of file.
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Change all defconfig fragments to take advantage of
"cf3cd4388a support/tests: allow properly indented config fragment".
Make each defconfig fragment:
- start after a backslash;
- be declared as a multi-line string literal;
- be indented one level more than the variable that contains it.
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Move the strip out of leading spaces in defconfig fragments from the
BRTest class to the Builder class. It actually postpones the strip out,
consequentially allowing test cases to post-process the defconfig in
their own __init__ before calling the __init__ method from BRTest.
Moving this code to the Builder class also allows any new test class
that inherits from BRTest to reuse the same code even if the new class
overrides the setUp method.
At same time, prepend a newline to the jlevel handling otherwise it
would stop working for defconfig fragments that don't end in a newline.
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
We sanity-check the host executables that they have a correct RPATH
pointing to the host libraries.
This is currently done by looking for all files in $(HOST_DIR) that
match the 'ELF executable' pattern (a bit more complex, but that's
idea).
However, when an executable is built with -fPIE of -fpie, it no longer
appears to be an 'ELF executable', but it rather looks like an 'ELF
sheard object' (like if it were an library.
So, we miss those files.
It turns out that the problem is a real one, because quite a few
mainline distros, expecially those based on Debian for example, have
already switched to generating PIE code by default, and thus we miss on
a whole class of systems..
We fix that by simply looking if we can find an ELF interpreter in each
file. If we there is one, this is an ELF executable; if not, it may be
anything else: we don't care (not even about ELF libraries).
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Arnout Vandecappelle <arnout@mind.be>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
grub is no longer maintained: it is stuck at version 0.97 with huge
patches that have no opportunity to be applied upstream, as upstream
has even renamed it grub-legacy.
Besides, it no longer builds correctly with recent binutils versions,
and even the huge patches we could grab from Debian do not help the
slightest.
Since upstream really considers it dead, and there are at least two
alternatives (grub2 and syslinux), just remove grub.
Add a legacy entry.
Remove the test cases as well.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Patches with renames apply properly with patch >= 2.7, but not with
older patch versions. Since "git format-patch" by default generates
patches with renames, Buildroot developers often don't realize that
their patches will not apply properly on build machines that have
patch < 2.7. In order to prevent such a situation from happening
again, this commit adds some logic in apply-patches.sh to refuse
applying patches that contain renames.
Note that just searching for '^rename' is not sufficient, since the
patch commit message may contain the words "rename from" or "rename to"
as well. Therefore, the grep expression is made as accurate as possible,
checking both.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
[Arnout: spaces instead of tabs (suggested by Yann);
extend commit message.]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Force gzip compression level 6 when calculating hash of a downloaded GIT repo.
To make sure the tar->gzip->checksum chain always provides consistent result.`
The script was relying on the default compression level, which must not be
necessarily consistent among different gzip versions. The level 6 is gzip's
current default compression level.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
When we list the available tests, we use test_dir, which is set from
the path of the script. However, when we run the tests, we use the
hard-coded path.
Ditto to find the config file.
For consistency, always use test_dir.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Commit c96b8675ea
("support/scripts/check-bin-arch: ignore symbolic links") was bogus,
because it tested ${f}, which is the relative path of the file inside
${TARGET_DIR}, so we end up testing if ${f} on the system is a
symbolic link.
This commit fixes that by testing ${TARGET_DIR}/${f}.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Since commit da32b49f00
("instrumentation: extend packages-file-list.txt with symlinks and
directories"), the packages-file-list.txt also contains symbolic
links. Therefore, check-bin-arch is now also checking symbolic links.
However, symbolic links in $(TARGET_DIR) can have absolute path as
targets, such as:
$ ls -l output/target/sbin/ifdown
lrwxrwxrwx 1 thomas thomas 10 Sep 3 15:55 output/target/sbin/ifdown -> /sbin/ifup
Therefore, we are now potentially checking a host binary, which
obviously makes check-bin-arch fail.
This commit changes check-bin-arch to ignore symbolic links. Indeed,
we have two cases:
- The symbolic link really points to something that will in the
rootfs (such as /sbin/ifup above). In this case, /sbin/ifup will be
checked separately by check-bin-arch.
- The symbolic link doesn't point to something that will be in the
rootfs, and that is not a problem from the perspective of
check-bin-arch, which checks the architecture of target binaries.
Fixes:
http://autobuild.buildroot.net/results/16d384a0183d477646ac7692feb65f00dde7d068/
(vim)
http://autobuild.buildroot.net/results/50429c0f63a8befff9e20899327b9a8d754d99be/
(ifupdown)
http://autobuild.buildroot.net/results/1db65973e782bfa61abcbccd3501bfd235f77288/
(gawk)
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add a parameter to run-tests to act as a multiplier for all timeouts of
emulator.
It can be used to avoid sporadic failures on slow host machines as well
in elastic runners on the cloud.
Cc: Arnout Vandecappelle <arnout@mind.be>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
[Arnout: rename multiplier to timeout_multiplier everywhere]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
We add the 3 following combinations:
- basic systemd, read-only, network w/ ifupdown
- basic systemd, read-only, network w/ networkd
- full systemd, read-only, network w/ networkd
The tests just verify what the /sbin/init binary is, and that we were
able to grab an IP address. More tests can be added later, for example
to check each systemd features (journal, tmpfiles...)
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Arnout: regenerate .gitlab-ci.yml]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The "builtin" kernel does not boot a systemd-based system, so
we resort to building the same one as currently used by our
qemu_arm_vexpress_defconfig.
We test the 8 following combinations:
- busybox, read-only, without network
- busybox, read-only, with network
- busybox, read-write, without network
- busybox, read-write, with network
- basic systemd, read-write, network w/ ifupdown
- basic systemd, read-write, network w/ networkd
- full systemd, read-write, network w/ networkd
- no init system, read-only, without network
The tests just verify what the /sbin/init binary is, and that we were
able to grab an IP address. More tests can be added later, for example
to check each systemd features (journal, tmpfiles...)
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Arnout Vandecappelle <arnout@mind.be>
[Arnout: update .gitlab-ci.yml]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The default audio backend for qemu is configured at compile time. It
generates annoying warning messages to qemu's stderr when running our
tests, like these:
pulseaudio: set_sink_input_volume() failed
pulseaudio: Reason: Invalid argument
pulseaudio: set_sink_input_mute() failed
pulseaudio: Reason: Invalid argument
Explicitly set the audio backend to "none" at runtime to remove those
messages from our logs. There is no command line argument for this, so
use an environment variable when starting qemu.
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The toolchain configuration used by the autobuilders to test the
internal toolchain backend on ARM contains an option that no longer
exists: BR2_UCLIBC_VERSION_NG. This option has been removed since
uClibc-ng has been made the one and only uClibc version supported.
Due to this option no longer existing, this toolchain configuration
was in fact never used, because the randgenconfig script validates
that a toolchain configuration is valid by checking that all lines are
still present in the final .config.
Therefore, this commit removes the bogus option, which will make sure
this toolchain config gets used again by our autobuilders.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This column is not used by either genrandconfig or test-pkg, so remove
it.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We currently have a list of toolchain configurations that are used by
the autobuilders at [1]. However, this makes it a little more difficult
for people to use these configurations, and also to have a different
list of configurations for different branches. For example if a new
architecture is introduced, the 2017.02.x branch doesn't have support
for this architecture yet so it shouldn't try to run those configs.
Therefore, include the autobuild config fragments directly in Buildroot,
so they can be branched together with the rest. We create a new
directory under support/ to store them.
Generated with
wget -nd --no-parent --recursive http://autobuild.buildroot.net/toolchains/configs/
The index.html file is removed.
The toolchain-configs.csv file is adapted so the URLs become relative
paths pointing to the config fragments.
[1] http://autobuild.buildroot.net/toolchains/configs/toolchain-configs.csv
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As suggested by Arnout in [1].
While at it, simplify the logic by always appending the BR2_JLEVEL and
defaulting to 0 (the value copied from Config.in is used for 5 years now
and is very unlikely to change).
[1] http://patchwork.ozlabs.org/patch/790525/
Suggested-by: Arnout Vandecappelle <arnout@mind.be>
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Cc: Arnout Vandecappelle <arnout@mind.be>
Tested-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Since commit cf3cd4388a the -j option is
silently ignored.
The configuration lines are processed using '\n'.join().
This function adds intervening occurrences of the separator, but the
resulting string does not end at a separator.
>>> "n".join(["a","b"])
'anb'
It results in a defconfig that does not end in a newline.
When BR2_JLEVEL is added by -j logic to the defconfig it ends up
concatenated to the last line of the defconfig.
BR2_TOOLCHAIN_EXTERNAL_CODESOURCERY_ARM=yBR2_JLEVEL=7
The resulting .config has the default BR2_JLEVEL=0.
Instead of just workaround this problem by adding a newline before
BR2_JLEVEL when -j is used, make the defconfig to end in a newline since
it is a more future-proof solution.
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Cc: Arnout Vandecappelle <arnout@mind.be>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Tested-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The defconfig is composed on-the-fly by test infra + tests.
Dump it to the logfile before running 'make olddefconfig' so it can
easily analysed when debugging.
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Cc: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Depending on Python implementation used for testing, time it takes to
perform a given test can vary pretty significantly. To accout for that
allow individual test functions to specify different timeout value.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
In order to be able to leverage the same test code for testing
different python interpreters (or wrappers around CPython) allow child
classes of TestPythonBase to override the name of the executable used
to run tests.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add Python3 version of TestPython2 to make sure both versions of
Python get unit-tested.
Modify the code of libc_time_test() to support that change (convert
the code to use Python3-style "print").
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
[Thomas: update .gitlab-ci.yml.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Convert TestPythonBase to a true base class that only provides code
implementing various tests without defining tests themselves in a
"discoverable" form.
To retain correct testing functionality, add TestPython2 derived class
that uses code from TestPythonBase to define actual runnable test.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Tested-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
[Thomas: fix typo in commit log, update .gitlab-ci.yml, both pointed
by Ricardo.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Some commands take more than 5 seconds to complete under QEMU, so add
provisions to allow individual unit-test to specify different duration
to avoid false negative test failures.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Tested-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The user shouldn't need to pass this manually when creating a test-pkg
config file. It's an absolutely harmless option to enable always.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We really want test-pkg to do the test with a paranoid unsafe path.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This minimal configuration is also very useful outside test-pkg. In
addition, it will simplify the config merge in a later patch.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit introduces the script "fix-rpath" able to scan a tree,
detect ELF files, check their RPATH and fix it in a proper way.
The RPATH fixup is done by the patchelf utility using the option
"--make-rpath-relative <root-directory>".
Signed-off-by: Samuel Martin <s.martin49@gmail.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The normal shell does not support the bashism "< <(...)". Therefore
we use a normal pipe to find files containing a specific string.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is because $(HOST_DIR)/usr is gone.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Currently, defining a config fragment in the runtime test infra requires
that the fragment not to be indented. This is beark, and causes grievance
when looking at the code (e.g. to fix it).
Just strip out all leading spaces/tabs when writing the configuration
lines into the config file, allowing in-line indented config fragments,
like so:
class TestFoo(bla):
config = bla.config + \
"""
FOO=y
# BAR is not set
"""
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Arnout Vandecappelle <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current test fails because of a legacy option, renamed during the
recent ext overhaul.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Cc: Samuel Martin <s.martin49@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Arnout Vandecappelle <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
In commit b78b50465c, the initialisation
of BRTest.builddir was moved to the __init__ function. However, it is
set based on BRTest.outputdir and that is only set when the -o argument
is given to run-tests. When called as "run-tests -l", there is no -o
argument so BRTest.outputdir remains unset.
To fix, keep BRTest.builddir at None when BRTest.outputdir is None.
While we're at it, drop the direct access to the class member. If a
subclass wishes to set outputdir to something else before calling
BRTest.__init__, they are free to do so.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Reported-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Tested-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
