Now that we have a template generating an equivalent genimage configuration.
The generated genimage is identical to these +/- file ordering and a
trailing comma / newline that is ignored by genimage, E.G. for rpi3-64:
@@ -8,9 +8,10 @@
"rpi-firmware/cmdline.txt",
"rpi-firmware/config.txt",
"rpi-firmware/fixup.dat",
- "rpi-firmware/start.elf",
"rpi-firmware/overlays",
- "Image"
+ "rpi-firmware/start.elf",
+ "Image",
+
}
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The rpi genimage configurations are all identical, except for the boot
partition files, which include:
- Device tree files (*.dtb)
- rpi-firmware files (rpi-firmware/*)
- Kernel image (Image/zImage)
All of these are quite simple to figure out programmatically based on the
content of BINARIES_DIR, so extend post-image.sh to fall back to generating
a genimage configuration based on genimage.cfg.in if a board specific one
does not exist.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Old links are no longer working, so use new links instead.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Old link is no longer working, so use new link instead.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Backport an upstream patch fixing the build with binutils >= 2.38
for riscv's for Zicsr and Zifencei.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/4987456149
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for PineCube with:
- U-Boot 2022.04
- Linux 5.15.61
PineCube is a low-powered, open source IP camera
with the following specs:
- Allwinner S3 Cortex-A7
- 128 MiB DDR3
- 16 MiB SPI flash
- 5 MPx OV5640 camera
- MicroSD slot
- 10/100M Ethernet with passive PoE
- 802.11 b/g/n WiFi
- Bluetooth 4.1
- USB 2.0
- 26 pins GPIO header
- Microphone
- IR LEDs for night vision
Board homepage: https://www.pine64.org/cube/
Board wiki: https://wiki.pine64.org/wiki/PineCube
Signed-off-by: Jan Havran <havran.jan@email.cz>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump qemu_arm_ebbr_defconfig and qemu_aarch64_ebbr_defconfig in sync:
- Bump Linux to v6.4.3
- Bump U-Boot to 2023.07.02
- Bump TF-A to v2.9
While at it, tune the documentation:
- Increase the amount of memory in the example commands to help run the
largest OS distributions.
- Update the link to the IR Guide to point at the latest version.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adds support for TI's SK-AM62 board by introducing the
am62x_sk_defconfig file and related support files.
More information about the board can be found at:
https://www.ti.com/tool/SK-AM62
Signed-off-by: Xuanhao Shi <x-shi@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adds support for TI's SK-AM64 board by introducing the
ti_am64x_sk_defconfig file and related support files.
More information about the board can be found at:
https://www.ti.com/tool/SK-AM64
Signed-off-by: Xuanhao Shi <x-shi@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Acked-by: Andrew Davis <afd@ti.com>
Tested-by: Bryan Brattlof <bb@ti.com>
Cc: Romain Naour <romain.naour@gmail.com>
Reviewed-by: Francois Perrad <francois.perrad@gadz.org>
Reviewed-by: Julien Olivain <ju.o@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The hss-payload-generator cannot find where u-boot.bin is when looking
for it using the config.yaml. Update syntax issues and working
directories. Fix the post image script to allow an image to get built.
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 2a5d90a595 (configs/rock5b: Add patches to fix gcc12 warnings)
introduced the kernel patches in an incorrect directory.
Fix that by moving them in the proper location.
Reported-by: Kilian Zinnecker <kilian.zinnecker@mail.de>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This patch introduces patches for the custom kernel, as it is
currently used for the Radxa Rock 5B. The patches fix two gcc
compiler warnings, which result in a build error, if the kernel
is used with gcc version 12.
Since also the code of custom board drivers for WiFi support is
affected, and no fixes are provided by the vendor, the custom WiFi
support is disabled.
Signed-off-by: Kilian Zinnecker <kilian.zinnecker@mail.de>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The upstream QEMU 'sifive_u' machine supports running upstream U-Boot
for the SiFive HiFive Unleashed board out of the box.
Add the QEMU instructions for testing in readme.txt.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
As the rootfs size is set to 60M, let's put it right on the 4M offset
in the SD card, so that the generated sdcard.img can be exactly
64M. This will allow sdcard.img to be accepted as an image by Qemu,
which requires power of two sizes for the disk images.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The issue seems to be fixed. I checked qemu and linux git repositories
but can not find any information when this is starting to work.
System gets successfully an IP, no further testing was done.
Tested with Qemu 8.0.3 and Linux 6.1.x.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use full relative pathes for rootfs and kernel, like in other
readme's.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Most of the users use HDMI console on RPi and with increasing popularity
of systemd they face a trouble.
systemd doesn't use /etc/inittab, enable getty@tty1.service instead.
Signed-off-by: Alexey Roslyakov <alexey.roslyakov@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update linux-3.14.config for Galileo to enable Linux kernel root
file system on NFS.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch adds a new defconfig for OrangePI PC2 board.
It was supported before in Buildroot, however due to problems in
building TF-A, it was removed in commit
eeede611f8. This commit re-adds it, in a
state that properly builds.
Signed-off-by: Javad Rahimi <javad321javad@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add defconfig for imxrt1050-evk is a development board from NXP.
The i.MXRTxxxx family spreads from i.MXRT1020 to i.MXRT1170 with the
first one supporting 1 USB OTG & 100M ethernet with a cortex-M7@500Mhz
up to the latter with i.MXRT1170 with cortex-M7@1Ghz and
cortex-M4@400Mhz, 2MB of internal SRAM, 2D GPU, 2x 1Gb and 1x 100Mb
ENET. The i.MXRT family is NXP's answer to STM32F7xx, as it uses only
simple SDRAM, it gives the chance of a 4 or less layer PCBs. Seeing
that these chips are comparable to the STM32F7xxs which have Buildroot
ported to them it seems reasonable to add support for them.
https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/i-mx-rt1050-evaluation-kit:MIMXRT1050-EVK
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Cc: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for the icicle kit, the main development board for
Microchip's PolarFire SoC.
The configuration file is microchip_mpfs_icicle_defconfig. It builds a
bootable kernel image with an embedded root file system. The image
built can be flashed to the board using the eMMC or an SD card.
The yaml configuration file is used by the hss payload generator. It
maps the ELF binaries or binary blobs to the individual application
harts (U54s).
The image generator script sets the partitions of the image.
The kernel fragment file sets additional configurations for the icicle
kit in buildroot that are not in the default configuration.
The image tree souce file creates a FIT image.
The post image script creates the payload using the payload generator
host package and finally, creates the FIT image using the ITS after the
kernel build.
The U-Boot script and additional U-Boot configurations ensure that
U-Boot behaves as expected for the icicle kit and boots the FIT image.
The readme.txt file documents how to build and boot the icicle kit with
this configuration.
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Reviewed-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit duplicates the asus_tinker_rk3288_defconfig changing:
- BR2_LINUX_KERNEL_INTREE_DTS_NAME to rk3288-tinker-s
- BR2_TARGET_UBOOT_BOARD_DEFCONFIG to tinker-s-rk3288
- extlinux.conf devicetree to /boot/rk3288-tinker-s.dtb
- root device format to <major>:<minor> in order to prevent the kernel to mount rootfs
from the wrong device
- Add Flávio Tapajós for configs/asus_tinker-s_rk3288_defconfig and for
configs/asus_tinker-s_rk3288_defconfig and for board/asus/tinker-s
Signed-off-by: Flávio Tapajós <flavio.tapajos@newtesc.com.br>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch bumps the versal_vck190_defconfig to xilinx-v2023.1 which includes
the following updates:
- Linux v6.1.5
- U-Boot v2023.01
- TF-A v2.8 (including mainline patches)
- PLM xilinx_v2023.1
- PSMFW xilinx_v2023.1
- versal-firmware uses new github.com/Xilinx/soc-prebuilt-firmware repo
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch cleans up the shellcheck issues in the versal post scripts.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The m68k Linux kernel build is broken with binutils >= 2.41 with:
arch/m68k/fpsp040/skeleton.S: Assembler messages:
arch/m68k/fpsp040/skeleton.S:502: Error: junk at end of line, first unrecognized character is `#'
arch/m68k/fpsp040/skeleton.S:508: Error: junk at end of line, first unrecognized character is `#'
This commit adds a backport from the upstream Linux kernel which fixes
this issue. Many thanks to Romain Naour for the issue investigation
and the identification of the kernel commit fixing this.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add ARC700 image configuration for nSIM instruction set simulator.
This is a nice starting point for ARC700 in nSIM.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit adds support for the i.MX8DXL SoC from NXP, by adding a
new BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX8DXL and propagate its
support in the affected packages.
Signed-off-by: Stefan Nickl <Stefan.Nickl@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch bumps the zynqmp defconfigs to xilinx-v2023.1 which includes
the following updates:
- Linux v6.1.5
- U-Boot v2023.01
- ATF v2.8 (including mainline buildroot patches)
- PMUFW xilinx_v2023.1
- Updated pm_cfg_obj.c from Vitis v2023.1
- Removed kria u-boot patch which is included with xilinx-v2023.1
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch cleans up the shellcheck issues in the versal post scripts.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
It was a leftover from the copy-and-paste of the readme.txt file of its
almost twin sister BSH SMM S2 PRO.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Kernel is built without network support, so network utils are useless.
This has a positive impact on the size of busybox and xipImage, making
them smaller.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiegineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch adds the defconfig file needed to build u-boot, kernel
and rootfs for the Rock 5B. In addition it adds a kernel config
fragment file, which activates the needed ethernet driver support.
It also adds a readme and post image scripts, needed to generate an
sdcard.img file, which can be flashed on an SD card to boot the
Radxa Rock 5B.
Signed-off-by: Kilian Zinnecker <kilian.zinnecker@mail.de>
[yann.morin.1998@free.fr:
- drop custom version
- fix shellcheck in post-image script
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Most rpi defconfigs use dtb overlays, but not rpi0 / rpi2 - Making it harder
to use overlays on those boards as the genimage files have to be tweaked.
To fix this, create the rpi-firmware/overlays directory in the post-build
script if needed and unconditionally include it in the genimage files so
rpi0/rpi2 works consistently with the other variants.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch cleans up board/zynqmp shellcheck issues.
Signed-off-by: Neal Frager <neal.frager@amd.com>
[Peter: wrap long lines, use quotes around entire word]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch cleans up board/zynq shellcheck issues.
Signed-off-by: Neal Frager <neal.frager@amd.com>
[Peter: use ${} for variables, quotes around entire word]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The ppc-mpc8544ds is the only qemu configuration that requires a kernel patch:
board/qemu/ppc-mpc8544ds/patches/linux/0001-powerpc-Fix-mcpu-options-for-SPE-only-compiler.patch
But this patch doesn't apply after a backport between v6.1.20 and v6.1.21
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=da0beae2449376326086e9f57468fd2b64736d2a
So the patch 0001-powerpc-Fix-mcpu-options-for-SPE-only-compiler.patch doesn't
seem required anymore.
Welcome to Buildroot
buildroot login: root
# uname -a
Linux buildroot 6.1.28 #1 Wed May 24 09:08:27 UTC 2023 ppc GNU/Linux
# cat /proc/cpuinfo
processor : 0
cpu : e500v2
clock : 400.000000MHz
revision : 3.0 (pvr 8021 0030)
bogomips : 800.00
timebase : 400000000
platform : MPC8544 DS
model : MPC8544DS
Memory : 128 MB
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/4306895282https://bugs.busybox.net/show_bug.cgi?id=15581
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Cc: Jan-Benedict Glaw <jbglaw@lug-owl.de>
Cc: Sebastian Weyer <sebastian.weyer@smile.fr>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Board support package includes the following components:
- mainline Linux kernel 5.15.108
- mainline U-Boot 2023.04
- default packages from buildroot
Note: There is a problem in u-boot display management. It should display
the ST microelectronics logo but "noise" is displayed (like when running
the command dd if=/dev/urandom of=/dev/fb0 in Linux). I also tried to
change version (even the first version in which this feature was
introduced), but without success. Despite this I decided not to disable
the video management configuration to remind us that it needs to be
fixed :).
Cc: Giulio Benetti <giulio.benetti@benettiengineering.com>
Link: https://www.st.com/en/evaluation-tools/32f769idiscovery.html
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Kernel is built without network support. It is useless to compile the
package and then remove it from rootfs.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
After booting Linux the userspace is unusable since every command issued,
that is a symlink to busybox, fails because of no free ram. So let's
disable IIO in linux.config to give some more ram to userspace.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The QEMU board's post-image script will glob through various
`readme.txt` files for an appropriate command line to use. Recent linter
changes [1] prevents this from happening, and results in the following
build error:
>>> Executing post-image script board/qemu/post-image.sh
sed: can't read board/qemu/*/readme.txt: No such file or directory
Reverting part of the shellcheck fixes for the README file arguments and
marking a linter exception.
[1]: b32d7c99c6
Signed-off-by: James Knight <james.d.knight@live.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
[yann.morin.1998@free.fr: also reinstate plural to the variable name]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Virtually all PCs nowadays have a PCI bridge and PCI devices.
All framnebuffer options depend on CONFIG_FB, which default is not 'y',
so also enable that.
The overwhelming majority of PCs nowadays also come with an UEFI
bootloader, that configures a framebuffer usable in early boot, which
the kernel can reuse without needing any hardware-specific driver.
EDID allows retrieving the capabilities of the connected display,
especially the frequencies and so on, to properly drive the display.
Signed-off-by: Adam Duskett <aduskett@gmail.com>
[yann.morin.1998@free.fr:
- drop cosmetic CONFIG_FRAMEBUFFER_CONSOLE_DEFERRED_TAKEOVER=y
- rewrite commit log to explain all new options
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Last-minute changes to d9b244d8a3 (board/qemu: define start qemu
script outside of post-image script) were not tested before being
pushed, so they introduced a bug.
As Arnout put it:
[...] multiple expressions need a -e to interpret them as
expressions (now they're interpreted as file names).
Fixes: d9b244d8a3
Reported-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: James Knight <james.d.knight@live.com>
Provides the ability to use a host system's QEMU. While a Buildroot
generated QEMU should work for most cases, a developer may wish to use
the system's QEMU for options which may not have been configured in the
Buildroot's QEMU build (e.g. configuring a different display mode).
Signed-off-by: James Knight <james.d.knight@live.com>
[yann.morin.1998@free.fr:
- use false/true instead of 0/1
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Provides the ability to forward command line options directly to QEMU.
When invoking `start-qemu.sh`, users can forward arguments by adding a
double dash (`--`) into the argument set, and any trailing arguments
will be forwarded into QEMU. For example, `start-qemu.sh -- --help`.
The original implementation supported a "serial-only" command line
argument to help run in a non-graphical mode for some use cases. These
changes try to promote a newly added `--serial-only` argument to drive
this mode; that being said, a `serial-only` argument will still be
accepted for backwards compatibility.
Signed-off-by: James Knight <james.d.knight@live.com>
[yann.morin.1998@free.fr:
- drop the warning: unknown options cause 'exit 1' already, and any
leftover is explicitly for qemu.
- use false/true instead of 0/1
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The following moves the definition of the QEMU board's `start-qemu.sh`
helper script from being inlined in the post-image script into its own
file. This should, in theory, make it easier to maintain the script in
the future.
Signed-off-by: James Knight <james.d.knight@live.com>
[yann.morin.1998@free.fr:
- don't sub-shell in the script
- merge all 3 sed calls into one
- create dest file with the sed, don't cp first
- also substitute HOST_DIR
- fix shellcheck
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Bump U-Boot to version 2023.04 and remove the patch that has already
been upstreamed.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle <arnout@mind.be>
Linux Kernel 6.1 now being officially promoted to be a LTS, this
commit bump the kernel version of this defconfig to 6.1.14.
A Kernel config fragment "linux.fragment" is now needed as the kernel
no longer enable SBI v0.1 support and the earlycon RISC-V SBI in its
riscv arch defconfig. See [1] [2].
The Spike riscv-isa-sim was updated upstream accordingly [3].
In order to keep a smooth transition, this kernel config fragment
re-enable those options to make sure this kernel will work with
both old Spike versions (not including commit [3] like the v1.1.0
currently included in Buildroot), and newer versions. This commit
was also successfully tested with riscv-isa-sim at commit
0d1a48c0c0.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=6f562570b9c5d6a3e30d87aec60a9d8f22a3203c
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=3938d5a2f9369d1ebd56320629fed395ce327e9c
[3] 191634d285
Signed-off-by: Julien Olivain <ju.o@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The kernel config board/qemu/aarch64-sbsa/linux.config has never been in
use by qemu_aarch64_sbsa_defconfig, neither via
BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE, nor via
BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES.
test_edk2.py is using the kernel config
board/qemu/aarch64-sbsa/linux.config. However, storing a kernel config
that is not used by qemu_aarch64_sbsa_defconfig, in a directory that is
"owned" by qemu_aarch64_sbsa_defconfig, is bound to cause confusion.
Therefore, move the config file to a new subdirectory:
support/testing/tests/boot/test_edk2/
This is similar to how e.g. test_grub.py has a subdirectory:
support/testing/tests/boot/test_grub/
where it keeps the kernel config that is only used by test_grub.py.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
ARM SBBR (Server Base Boot Requirements) defines SPCR (Serial Port
Console Redirection Table) as a mandatory ACPI table that specifies
the configuration of a serial console.
In the linux kernel, ARM developers have decided that consoles defined
by SPCR are always enabled when existing, see e.g.:
https://lore.kernel.org/linux-serial/20200430161438.17640-1-alpernebiyasak@gmail.com/T/
Specifying console=ttyAMA0 (which is a serial console) is thus
redundant for an ARM SBSA board. (It also blindly assumes that
the serial console is on ttyAMA0, which might not be true.)
Drop the explicit console=ttyAMA0 on the kernel command line,
such that the kernel can pick up the default console defined
by SPCR.
This is similar to how it is currently done for
board/aarch64-efi/grub.cfg.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Specifying /dev/sda2 is ambigious, and when booting my arm64 machine
this tries to mount the second partition of my ATA drive, instead of
the second partition of the USB-stick, simply because the ATA driver
is probed earlier than the USB controller driver.
To solve this problem, use PARTLABEL=root to specify the root filesystem.
This is similar to how it is currently done for board/aarch64-efi/grub.cfg
and board/qemu/aarch64-ebbr/grub.cfg.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Bump Linux kernel to v6.1.13 and increase the rootfs size accordingly.
- Bump the FVP in the readme to version 11.20 build 15 and update the
command line.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Bump Linux kernel version to 6.1.12.
- Bump U-Boot version to 2023.01 and rename config fragment to make it
clearer that it is not a complete config file.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
- Bump Linux kernel version to 6.1.12.
- Bump U-Boot version to 2023.01 and follow CONFIG_SYS_TEXT_BASE renaming.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add a link to RVspace Documentation Center, which did not exist
when readme.txt was first submitted. It provides datasheet, quick
start, schematics, and so on.
Signed-off-by: Francois Dugast <francois.dugast.foss@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
We're not using next branch so let's rename label linux-next to linux.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
During the last U-boot version bump it's not been noted that the TPL
was not prepended to SPL anymore preventing the board to boot, so
let's copy TPL to the image folder, prepend it to u-boot-spl-dtb.bin
and place it at offset 32KB, where RK3288 bootrom expects to find
it. Let's also place u-boot-dtb separated from SPL at offset 8M, where
the SPL expects it to find it.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Starting from version 2021.10 only distro booting is supported, as
reported by commit ff8f277e9121 ("ti: am335x_evm: Switch to DISTRO_BOOT only").
The patch allows to update U-Boot to versions later than 2021.10.
Tested on beaglebone black.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
If using BR2_LINUX_KERNEL_CUSTOM_DTS_PATH to copy .dts files from
buildroot into the linux tree, these .dts files are copied to
arch/arm64/boot. Unfortunately, the post-image.sh script expects to find
them in arch/arm64/boot/xilinx.
This patch does not require the xilinx/ prefix to be present when
symlinking the device-tree to system.dtb where u-boot expects to find
it.
It is effectively applying the below patch for zynqmp to versal as well:
https://patchwork.ozlabs.org/project/buildroot/patch/20230201195956.1758827-1-gsmecher@threespeedlogic.com/
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
If using BR2_LINUX_KERNEL_CUSTOM_DTS_PATH to copy .dts files from
buildroot into the linux tree, these .dts files are copied to
arch/arm64/boot. Unfortunately, the post-image.sh script expects to find
them in arch/arm64/boot/xilinx.
This patch does not require the xilinx/ prefix to be present when
symlinking the device-tree to system.dtb where u-boot expects to find
it.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add a defconfig to build a 32b ARMv7-A U-Boot based firmware implementing
the subset of UEFI defined by EBBR[1], as well as a Linux OS disk image
booting with UEFI, to run on Qemu.
The generated firmware binary can also be used to install or run another OS
supporting the EBBR specification.
[1]: https://github.com/ARM-software/ebbr
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit adds support for the BeagleBone Green Wireless to the
existing beaglebone_defconfig, by making sure the relevant Device Tree
is built and installed.
Signed-off-by: Ramon Crichlow <rcrichlow9000@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
BSH SMM S2 PRO (SystemMaster S2 Pro) Board is an add-on board which
provide input and output interfaces to a dedicated carrier board. It is
designed mainly to provide graphical/video and connectivity interfaces
to the appliance.
Board support package includes the following components:
- mainline Linux kernel 6.1.6
- mainline U-Boot 2022-07
- Default packages from buildroot
https://www.apertis.org/reference_hardware/imx8mn_bsh_smm_s2pro_setup/
Add Ariel D'Alessandro and Dario Binacchi as co-maintainer, we work
together on platform mainline
Build and tested using:
docker pull registry.gitlab.com/buildroot.org/buildroot/base:20220105.2314
Cc: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Heiko Thiery <heiko.thiery@gmail.com>
Cc: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
BSH SMM S2 (SystemMaster S2) Board is an add-on board which provide
input and output interfaces to a dedicated carrier board. It is designed
mainly to provide graphical/video and connectivity interfaces to the
appliance.
Board support package includes the following components:
- mainline Linux kernel 6.1.6
- mainline U-Boot 2022-07
- default packages from buildroot
https://www.apertis.org/reference_hardware/imx8mn_bsh_smm_s2pro_setup/
The smm s2 board is basically the same as the pro except it boots from
NAND instead of eMMC.
Co-authored-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The updated device tree is provided by Acme Systems:
https://www.acmesystems.it/compile_kernel_5_15
It is released under GPLv2 or later.
Signed-off-by: Edgar Bonet <bonet@grenoble.cnrs.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reduce the configs in the kria/uboot.fragment to only what is necessary.
These 4 configs are already included in the xilinx_zynqmp_virt_defconfig, so
it is redundant to include them in the kria/uboot.fragment file. Applying
this patch has zero impact on the u-boot binaries that are built.
This patch has been build and run tested on a kria kv260 starter kit.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Follow changes to other OrangePi boards, most importantly
orangepi-zero-plus2, which this board support is based on. This includes
switching to extlinux as boot mechanism and dropping custom U-Boot boot
script.
Rootfs image no longer fits into default 60M (mostly due to Linux
modules), so increase it to 120M.
While at it, bump Linux to 6.1.4 and U-Boot to 2023.01.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
When using the buildroot compiler, it builds the u-boot.itb immediately
after building the fit-dtb.blob. This causes a build failure when using
the CONFIG_MULTI_DTB_FIT build configuration. This patch adds the necessary
dependency to guarantee that the fit-dtb.blob has finished building before
trying to build the u-boot.itb.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/3310463281
This patch has been submitted to u-boot mainline:
https://lore.kernel.org/all/20221221075446.47141-1-neal.frager@amd.com/
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
http://freescale.com/ urls are all redirected to the NXP homepage
https://www.nxp.com/
Even if the link is not broken in the sense of a 404 http error, the
pointed resource is not found.
This commit updates the old freescale link to the correct nxp.com
location.
Note: the link now requires a free registration to be accessed.
Signed-off-by: Julien Olivain <ju.o@free.fr>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
http://freescale.com/ urls are all redirected to the NXP homepage
https://www.nxp.com/
Even if the links are not broken in the sense of a 404 http error, the
pointed resources are not found.
This commit updates the old freescale links to the correct nxp.com
locations.
Note: the link to the SABRE for Automotive Infotainment Quick Start
Guide now requires a free registration to be accessed.
Signed-off-by: Julien Olivain <ju.o@free.fr>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
http://freescale.com/ urls are all redirected to the NXP homepage
https://www.nxp.com/
Even if the link is not broken in the sense of a 404 http error, the
pointed resource is not found.
This commit updates the old Freescale link to the correct nxp.com
location.
Signed-off-by: Julien Olivain <ju.o@free.fr>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Add a defconfig for the Starfive VisionFive2 board, a board built around the
Starfive JH7110 RISC-V 64bit SoC.
This board comes with functional lowlevel and U-Boot bootloaders in SPI
flash. The defconfig reuses these and only builds a (5.15 based) kernel and
rootfs.
The factory shipped U-Boot is hard coded to look at MMC partition 3.
Signed-off-by: Francois Dugast <francois.dugast.foss@gmail.com>
[Peter: add to DEVELOPERS]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Lichee RV Dock is a RISC-V Linux development kits with high integration,
small size and affordable price designed for opensource developer.
https://wiki.sipeed.com/hardware/en/lichee/RV/Dock.html
Signed-off-by: Angelo Compagnucci <angelo@amarulasolutions.com>
Tested-by: Indrek Kruusa <indrek.kruusa@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Lichee RV - Nezha CM is a compute module with modular design, equipped
with Allwinner D1 chip (based on T-Head XuanTie C906 core), 512MB DDR3
RAM.
Board support is based on the nezha defconfig already available in
buildroot.
https://wiki.sipeed.com/hardware/en/lichee/RV/RV.htmlhttps://linux-sunxi.org/Sipeed_Lichee_RV
Signed-off-by: Angelo Compagnucci <angelo@amarulasolutions.com>
Reviewed-by: Indrek Kruusa <indrek.kruusa@gmail.com>
Tested-by: Indrek Kruusa <indrek.kruusa@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This is now based on U-Boot 2022.10 and has gained SPL support, so use that
instead of sun20-d1-spl. With this we can also drop the u-boot patch and
patch directory.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch fixes a problem in the vck190 boot.bin generation as it should be
using the u-boot.dtb as the u-boot device tree and not the Linux system.dtb.
While both dtbs are basically the same, it is better not to mix this up.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since commit
5bbc20154e ("configs/zynqmp_kria_kv260_defconfig:
bump to Xilinx 2022.2"), we're using U-Boot version Xilinx 2022.2,
which already carries the psu_init_gpl.c, causing the build to fail as
our patch doesn't apply.
Fix this by dropping the no longer needed patch.
Fixes: 5bbc20154e ("configs/zynqmp_kria_kv260_defconfig: bump to Xilinx 2022.2")
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since commit
3c997c457a ("configs/zynqmp_zcu106_defconfig:
bump to Xilinx 2022.2"), we're using U-Boot version Xilinx 2022.2,
which already carries the psu_init_gpl.c, causing the build to fail as
our patch doesn't apply.
Fix this by dropping the no longer needed patch.
Fixes: 3c997c457a ("configs/zynqmp_zcu106_defconfig: bump to Xilinx 2022.2")
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch moves the board/zynqmp/kria/kv260/uboot.fragment file
to the board/zynqmp/kria directory. The reason is that this file
is the same for any kria starter kit and is not specific to the kv260.
By moving the file, it can be logically re-used with the kr260 when
support for this starter kit is added to buildroot.
KR260 Starter Kit:
https://www.xilinx.com/products/som/kria/kr260-robotics-starter-kit.html
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch adds support for Xilinx Versal VCK190 evaluation board.
VCK190 features can be found here:
https://www.xilinx.com/products/boards-and-kits/vck190.html
The VCK190 is based on the Xilinx Versal family:
https://www.xilinx.com/products/silicon-devices/acap/versal.html
The VC1902 included with the VCK190 evaluation board has Xilinx
AI Engine acclerators designed for accelerating machine learning
applications. Also included is an upgrade from prior Zynq and
ZynqMP families to ARM Cortex-A72 cores.
While the Linux kernel for Versal is quite similar to ZynqMP,
the boot process has significantly changed.
Triple-redundant MicroBlaze cores are used to boot and setup
Versal devices. For this reason, current buildroot support
will download pre-built firmware images and use Xilinx bootgen
to generate the boot.bin for the vck190.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch bumps following packages to the newer version:
- OpenSBI v1.1
- U-boot v2022.10
- Linux 6.0
Linux kernel is hosted on AndesTech Github which includes ethernet,
SD card, DMAC, RTC, WDT drivers support. OpenSBI is based on v1.1
with andes platfrom fdt driver.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch fixes the kv260.sh to generate a working u-boot.itb
now that the CONFIG_MULTI_DTB_FIT u-boot option is no longer used.
This is a follow-up fix of
515319b86f ("board/zynqmp/kria/kv260/uboot.fragment:
remove unnecessary CONFIG_MULTI_DTB_FIT option") to fix the build of:
https://gitlab.com/buildroot.org/buildroot/-/jobs/3310463281
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch removes the CONFIG_MULTI_DTB_FIT u-boot option for the
zynqmp_kria_kv260_defconfig as it is not necessary. The post build
kv260.sh creates the proper u-boot.itb without needing this option.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/3310463281
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch migrates the u-boot device tree definition
from uboot.fragment files to use BR2_TARGET_UBOOT_CUSTOM_MAKEOPTS
instead for the zynqmp_kria_kv260_defconfig.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch migrates the u-boot device tree definition
from uboot.fragment files to use BR2_TARGET_UBOOT_CUSTOM_MAKEOPTS
instead for the zynq_zc706, zynq_zed and zynq_microzed defconfigs.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This defconfig has been failing to build for several months, with
nobody stepping up to fix it. It's time to drop it.
See
https://lore.kernel.org/buildroot/20220806224338.0159e15c@windsurf/
for a notification on August 6, 2022 about the issues with this
defconfig.
This defconfig did not even have an entry in the DEVELOPERS file.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/3234499140
Cc: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This defconfig has been failing to build for several months, with
nobody stepping up to fix it. It's time to drop it.
See
https://lore.kernel.org/buildroot/20220806224338.0159e15c@windsurf/
for a notification on August 6, 2022 about the issues with this
defconfig.
This defconfig did not even have an entry in the DEVELOPERS file.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/3234499051
Cc: Filip Skoneczny <fskoneczny@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This defconfig has been failing to build for several months, with
nobody stepping up to fix it. It's time to drop it.
See
https://lore.kernel.org/buildroot/20220806224338.0159e15c@windsurf/
for a notification on August 6, 2022 about the issues with this
defconfig.
This defconfig did not even have an entry in the DEVELOPERS file.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/3234499050
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This patch migrates the u-boot device tree definition
from uboot.fragment files to use BR2_TARGET_UBOOT_CUSTOM_MAKEOPTS
instead for the zynqmp_zcu102 and zynqmp_zcu106 defconfigs.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add BR2_TARGET_UBOOT_NEEDS_GNUTLS=y and BR2_TARGET_UBOOT_NEEDS_UTIL_LINUX=y
since this are dependencies for building mkeficapsule u-boot tool.
Change the offset of the rootfs to left enough space for the U-Boot that
has increased.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently, the cmdline.txt file is installed in $(BINARIES_DIR) by the
rpi-firmware package. Overriding files in there can not be done with an
overlay (which only applies to $(TARGET_DIR)), and thus requires using
either a post-build or post-image script, which is not always very
practical when a custom file must be used.
Like was done in 689b9ac439 (package/rpi-firmware: rework boot/config
file handling) for config.txt, add an option to allow users to specify
the path to a custom cmdline.txt.
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Add a defconfig to build an AArch64 U-Boot based firmware implementing the
subset of UEFI defined by EBBR[1], as well as a Linux OS disk image booting
with UEFI, to run on Qemu.
The generated firmware binary can also be used to install or run another OS
supporting the EBBR specification.
We do not have Linux 5.19 headers at the moment therefore we rely on 5.17
in the defconfig.
[1]: https://github.com/ARM-software/ebbr
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Reviewed-by: Romain Naour <romain.naour@gmail.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add a defconfig for the Starfive VisionFive board, a board built around the
Starfive JH7100 RISC-V 64bit SoC (same as Beaglev).
This board comes with functional lowlevel and U-Boot bootloaders in SPI
flash. The defconfig reuses these and only builds a (6.0 based) kernel and
rootfs.
The factory shipped U-Boot is hard coded to look at MMC partition 3 and
misses some variables, so we provide a uEnv.txt to fix that up, based on
what is done in provided Fedora image.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Update description:
TF-A to v2.4-stm32mp-r1
U-boot to version v2020.10-stm32mp-r2.1
Linux to v5.10-stm32mp-r2.1
This patch also updates U-boot to to use FIP image.
Reference:
https://octavosystems.com/octavo_products/osd32mp1-brk/
The device tree blobs, and the U-boot patches come from Octavo System:
https://github.com/octavosystems/meta-octavo-osd32mp1
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update description:
TF-A to v2.4-stm32mp-r1
U-boot to version v2020.10-stm32mp-r2.1
Linux to v5.10-stm32mp-r2.1
This patch also updates U-boot to to use FIP image.
Reference:
https://octavosystems.com/octavo_products/osd32mp1-red/
The device tree blobs, and the U-boot patches come from Octavo System:
https://github.com/octavosystems/meta-octavo-osd32mp1
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
mender-grubenv no longer uses the mender_grubenv* directories, instead opting
to put the mender_grubenv directories in a grub-mender-grubenv top-level
directory. While there is a legacy install mode which keeps the two separate
directories, it is better to move forward and rip the bandaid off before it
becomes too painful to update in the future if the legacy option is removed
entirely.
- Update the license file sha256 sum due to a year change.
- mender-grubenv no longer installs grub.cfg, so mender_grub.cfg must be copied
manually to grub.cfg.
- BOOT_DIR replaces ENV_DIR in the Makefile.
- The sleep grub2 module is now a requirement.
- /etc/mender_grubenv.config file must be present on the system for the
grub-mender-grubenv-{print,set} scripts to work properly.
In addition to the above changes, update the mender example board file to work
with the updated mender-grubenv version.
Signed-off-by: Adam Duskett <aduskett@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This uses a newer firmware implementation that is much faster at
booting. It is supported as of Qemu 7.0.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Update the listed versions to match current status since commit
b4d9b51508 ("configs/solidrun_macchiatobin: bump BSP components").
All components are now from upstream so no need to state that for each
one.
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Opensbi is now based on 1.1, U-Boot on 2022.07-rc3 and Linux on 5.19-rc1.
We don't yet support 5.19 kernel headers, so use 5.17 instead.
The incompatibility between opensbi and u-boot is now fixed, so drop
0001-arch-riscv-dts-sun20i-d1.dtsi-adjust-plic-compatible.patch.
The updated device tree in the kernel tree no longer specifies a memory
node (and the board exists in 512M/1G/2G variants, so instead use the
(otherwise identical) device tree provided by u-boot, where the memory
node is fixed up based on the detected memory size.
On riscv, the linux kernel unconditionally wants to build its bundled
dtc, so it needs flex and bison, even if it is not going to build any
DTB. We can get flex and bison either via the system ones, or we get
them as they are in LINUX_KCONFIG_DEPENDENCIES. However, relying on this
is a bit fragile, so we keep asking the kernel to build a DTB, so that
we do ensure that our host-{flex,bison} are built and in the dependency
chain of the kernel (for PPD).
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
[yann.morin.1998@free.fr:
- extend on why we keep building a DTB from the kernel
]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
When enable DM for SPL binary, the DTB part of SPL may not 4 bytes aligned.
If u-boot-spl is not aligned, the offset of the DDR firmware is not 4
byte aligned when u-boot-spl-ddr.bin is created. This causes the ddr
firmware to not be loaded correctly at boot.
See imx-mkimage commit
https://source.codeaurora.org/external/imx/imx-mkimage/commit/?id=bba038d893046b44683182dba540f104dab80fe7
for the imx-mkimage details.
Signed-off-by: Bram Vlerick <bram.vlerick@openpixelsystems.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump the kernel version for all riscv nommu configs from 5.18 to 5.19.
That way, we can remove the one and only riscv nommu patch,
since this patch is included in kernel 5.19.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
nanopi-neo no longer builds, as uboot needs python2 on the host:
https://gitlab.com/buildroot.org/buildroot/-/jobs/2812053540
I no longer have access to that board, so I can't test an update to
either uboot or the kernel anymore.
Drop the board.
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The readme.txt contains a make target that does not match the actual
defconfig file name, fix that.
Fixes: 1500b7d5c8 ("configs/broadcom_northstar: new defconfig")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Broadcom Northstar family of SoCs is most commonly used for home
routers. It's an ARM platform with Cortex-A9 CPU(s).
All known Northstar devices come with CFE bootloader which almost
always expects a TRX firmware format (with exception for D-Link). Some
vendors (like Luxul and Netgear) wrap TRX in their own containers.
This board code provides:
1. Minimal kernel with support for on-SoC blocks. It enables Linux
drivers for SoC, watchdog, Ethernet, switch, USB, PCIe, LEDs).
2. Post image script building firmware images. In uses Buildroot
packages tools (lzma_alone, otrx, lxlfw) to build
bootloader-compatible images that can be flashed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Those components are aligned with NXP BSP lf-5.10.72-2.2.0.
This commit also refresh the readme.txt file:
- update no longer working URLs,
- enhance flashing instructions (use ${mmcdev} uboot variable),
- add "bs=1M" option to dd for better flashing performances.
Fixes:
- https://gitlab.com/buildroot.org/buildroot/-/jobs/2781800735
Signed-off-by: Julien Olivain <ju.o@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Those components are aligned with NXP BSP lf-5.10.72-2.2.0.
This commit also refresh the readme.txt file:
- update no longer working URLs,
- enhance flashing instructions (use ${mmcdev} uboot variable),
- add "bs=1M" option to dd for better flashing performances.
Fixes:
- https://gitlab.com/buildroot.org/buildroot/-/jobs/2781800730
Signed-off-by: Julien Olivain <ju.o@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump U-Boot to version 2022.04 and remove the two patches
that have already been upstreamed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-By: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The filename was changed from bootloader-BEAGLEV to bootloader-JH7100, update
the documentation for the beaglev board as well.
Signed-off-by: Christian Stewart <christian@paral.in>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Buildroot currently has all of the needed packages to use Mender as the primary
update system. However, there isn't any documentation or examples now that
provide a starting point for users. This lack of documentation makes setting up
a Mender based update system difficult and time-consuming.
Provided in this patch series is a mender_x86_64_efi_defconfig of which sets up
an x86_64 EFI based build that is ready to flash to a USB pen drive or use in a
QEMU environment. The system partition schema comprises of two equally sized
root partitions and a data partition that mounts to /var/lib/mender as a
persistent data store partition.
There is a board/mender/readme.txt provided, which gives users documentation on
how to flash the built image or boot the image using QEMU as well.
The post-build and post-image-efi scripts also have four options:
-a --artifact-name:
- The name of the artifact, this is added to /etc/mender/artifact_info
-o --data-part-size:
- The data partition size.
-d --device-type
- The device-type used by mender to catagorize registered devices.
Signed-off-by: Adam Duskett <Aduskett@gmail.com>
Signed-off-by: Mikael Bourhis-Cloarec <mikael.bourhis@smile.fr>
[Romain: rebase on master (01.2022)
- update genimage-efi.cfg to use GPT partition table and genimage-15 syntax
- bump the kernel to 5.15.13
- Add host-libelf kernel dependency
- Use BR2_TARGET_GRUB2_BUILTIN_MODULES_EFI after commit 82d1e8c628
(boot/grub2: use none platform when building for host)
- Add regexp grub mandatory module for mender-grubenv
- remove startup.nsh from genimage-efi.cfg after commit 3efb5e31fc
(board, boot, package: remove usage of startup.nsh in EFI partition)]
Signed-off-by: Romain Naour <romain.naour@smile.fr>
[Arnout:
- abbreviate sizes and partition uuids, remove implicit ones in genimage.cfg
- change data partition uuid to Linux (instead of x86_64 rootfs)
- fix whitespace and shellcheck errors in scripts
- remove --generate-mender-image option, always create it
- remove empty directory and -O ^64bit when creating data fs
- remove redundant e2fsck
- add -serial stdio option to qemu call
- update kernel to current stable 5.18.14
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
