Analog audio is enabled by default in sunxi_defconfig since commit 5d2408c6
(ARM: configs: sunxi: Add sun8i analog codec), so drop from fragment.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Now that upstream supports this board add buildroot support for it,
too.
This supports:
- latest upstream linux kernel. Since the support for this board and
its SoC is still in active development, we want to follow the
upstream kernel releases for now.
- building an image which can be installed to eMMC, SD card or USB
thumb drive.
- upstream u-boot patches are pending, therefore no support for
building a bootloader for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Now that RISC-V 32-bit (RV32) support has been merged into mainline
glibc, we can use the Linux 5.4 kernel.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The apu2 by PC Engines is a 64 bit single board computer with coreboot
BIOS. It only has serial output, but no graphics chip. With its 2–4
ethernet ports, it is often used to build a firewall or router.
The provided defconfig configures busybox and isolinux. It will output
a hybrid ISO image that can be written to a USB stick or burned to a
CD.
Configuration based on a blogpost by Tony Arkles:
http://www.better-bsp.com/blog/2017/03/02/buildrooting-for-apu2/
Signed-off-by: Danilo Bargen <mail@dbrgn.ch>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A defconfig for the friendlyarm nanopc-t4 was added in
c23895f06e, but then removed
in 8efd4463f7 because an ARM32
compiler was needed to build ATF, and this was not supported
back then.
Now, since package/arm-gnu-a-toolchain/ has been added, this
defconfig can be re-introduced.
Following new changes are introduced in comparision with the
older changeset:
- updated readme
- GPT partition layout is being used
- update defconfig to build ATF
- bump u-boot to 2020.07
- bump linux to 5.8.2
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: fixate U-Boot version; remove blind BR2_TARGET_UBOOT_NEEDS_PYTHON]
A defconfig for the friendlyarm nanopi-m4 was added in
493c3979a4, but then removed
in a24bd8936f because an ARM32
compiler was needed to build ATF, and this was not supported
back then.
Now, since package/arm-gnu-a-toolchain/ has been added, this
defconfig can be re-introduced.
Following new changes are introduced in comparision with the
older changeset:
- readme updated
- GPT partition layout
- update defconfig to build ATF
- bump u-boot to 2020.07
- bump linux to 5.8.2
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: fixate U-Boot version; remove blind BR2_TARGET_UBOOT_NEEDS_PYTHON]
A defconfig for the rockpro64 was added in
59e1077b4e, but then removed
in 10f49213b7 because an ARM32
compiler was needed to build ATF, and this was not supported
back then.
Now, since package/arm-gnu-a-toolchain/ has been added, this
defconfig can be re-introduced.
Following new changes are introduced in comparision with the
older changeset:
- renamed defconfig from pine64_rockpro64 to rockpro64
- updated readme
- using a GPT partition layout
- update defconfig to build ATF
- bump u-boot to 2020.07
- bump linux to 5.8.2
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: fixate U-Boot version; remove blind BR2_TARGET_UBOOT_NEEDS_PYTHON]
Mainline Linux now has basic s500/roseapplepi support, so switch to that to
get rid of the dependency on gcc7. Add two patches for the dts / fix that
didn't make it for kernel 5.7.
The mainline kernel does not yet have support for the mmc interface, so
change to initramfs for now. Patches for mmc support have been posted
recently, so this can be reverted once they show up in a stable kernel:
https://lore.kernel.org/lkml/cover.1593124368.git.cristian.ciocaltea@gmail.com/
The owl serial port is called ttyOWLn in mainline, so adjust the bootargs to
match. Also drop the unneeded execute permission on uEnv.txt.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for RK3288 SOM based radxa rockpi-n8
target with below features:
- Custom U-Boot 2020.07-rc4
https://github.com/amarula/u-boot-amarula.git
commit: "ba120841bf40ebaed049d64bb4f980083a1cf6b7"
- Custom Linux 5.7.0-rc1
https://github.com/amarula/linux-amarula.git
commit: "5dcb0132685b07beb82065c5d7521e6c555c55b6"
- GPT partition layout is being used
- Default packages from buildroot
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/674933582
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Signed-off-by: Oleksandr G Zhadan <Oleks@ArcturusNetworks.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The Banana Pi M2 Zero [1] is a board from Sinovoip, based on the
Allwinner H2+ SoC.
It is similar to the other Banana Pi M2* boards, from which this
configuration is inspired.
[1]: http://www.banana-pi.org/m2z.html
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With this patch we enable CONFIG_USB for HSDK, which is not explicitly
selected by UDL since the commit 5d50bd440bc2 ("drm/udl: Make udl
driver depend on CONFIG_USB"). Commit 4c13ca86dcf8 ("ARC:
[plat-hsdk]: fix USB regression") is not yet backported to Linux
kernel 5.6.x, so we enable this option in fragment file for HSDK.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: arc-buildroot@synopsys.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Basic support for the Marvell ESPRESSObin, by Globalscale Technologies.
http://espressobin.net
The kernel config has been extended with a fragment to enable switchcore
support, DSA drivers, and VLAN filtering in the bridge. To make use of
this you need a custom libnl based application, or the iproute2 suite
rather than the brctl tools, which don't support the VLAN filtering.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for imx6ullevk_defconfig that allows booting a mainline
kernel and mainline U-Boot.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add the new SAMA5D27 WLSOM1 Evaluation Kit with linux4sam_6.2
components. Update README file with new defconfigs and new
packages/website.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Since commit 'package/rpi-firmware: fix startup file names' ([1]) the
start and fixup file names are normalized to start.elf/fixup.dat,
adjust the rpi4 genimage config files accordingly.
Fixes:
ERROR: file(rpi-firmware/fixup4.dat): stat(.../images/rpi-firmware/fixup4.dat) failed: No such file or directory
ERROR: vfat(boot.vfat): could not setup rpi-firmware/fixup4.dat
[1] https://git.buildroot.net/buildroot/commit/?id=1bdc0334ff6273761b2e7fda730cdcc7e1f46862
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for RK3399 based rockpi-4 targets (model A, B, C)
with below features:
- Custom U-Boot 2020.07-rc4
https://github.com/amarula/u-boot-amarula.git
branch rock-pi
- Linux 5.4.46
- GPT partition layout is being used
- Default packages from buildroot
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add initial support for RK3399PRO SOM based rockpi-n10 target
with below features:
- Custom U-Boot 2020.07-rc4
https://github.com/amarula/u-boot-amarula.git
branch rock-pi
- Linux 5.7.2
- GPT partition layout is being used
- Default packages from buildroot
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
virtio-fs allow sharing a directory between the host and the guest.
It require virtiofsd daemon running before starting Qemu.
The wiki [1] recommand to enable the following kernel options:
CONFIG_VIRTIO
CONFIG_VIRTIO_FS
CONFIG_DAX
CONFIG_FS_DAX
CONFIG_DAX_DRIVER
CONFIG_ZONE_DEVICE
But virtio-fs works fine with only VIRTIO_FS.
Note: ZONE_DEVICE can only be enabled on aarch64 since kernel >= 5.7.
ARCH_ENABLE_MEMORY_HOTREMOVE support is missing for previous kernel [2].
[1] https://virtio-fs.gitlab.io/howto-qemu.html
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=bbd6ec605c0fc286c3f8ce60b4ed44635361d58b
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
>From [1]:
This kernel option allow exporting of the QEMU firmware configuration (fw_cfg)
file entries via sysfs. Entries are found under /sys/firmware/fw_cfg when this
option is enabled and loaded.
Enable the suboption to allow the qemu_fw_cfg device to be initialized via the
kernel command line or using a module parameter.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/drivers/firmware/Kconfig?h=v5.4.42#n187
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This driver is intended to be used by mesa virgl Gallium on the guest.
virtio-gpu is enabled by adding "-device virtio-gpu-pci" on the qemu
command line.
It's detected by lspci and dmesg log:
$ lspci
00:01.0 Display controller: Red Hat, Inc. Virtio GPU (rev 01)
$ dmesg
virtio-pci 0000:00:01.0: enabling device (0000 -> 0002)
[drm] pci: virtio-gpu-pci detected at 0000:00:01.0
[drm] virgl 3d acceleration not supported by host
[drm] EDID support available.
[TTM] Zone kernel: Available graphics memory: 51876 KiB
[TTM] Initializing pool allocator
[TTM] Initializing DMA pool allocator
[drm] number of scanouts: 1
[drm] number of cap sets: 0
[drm] Initialized virtio_gpu 0.1.0 0 for virtio2 on minor 0
The framebuffer interface fb0 is now present in /dev
$ ls /dev/fb*
/dev/fb0
See:
https://www.kraxel.org/blog/2019/09/display-devices-in-qemu/https://at.projects.genivi.org/wiki/display/WIK4/GENIVI+Technical+Summit+Session+Content+2018?preview=%2F28412356%2F28412481%2F2018-10-11_GeniviBangalorTechSummit_Virtio_GPU.pdf
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add the CONFIG_PCI symbol due a change in kernel 5.0 [1].
The option was previously enabled by default (default y).
"PCI: consolidate PCI config entry in drivers/pci
There is no good reason to duplicate the PCI menu in every architecture.
Instead provide a selectable HAVE_PCI symbol that indicates availability
of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the
rest in drivers/pci."
Qemu aarch64 provide a PCIe Host bridge but it require CONFIG_PCI_HOST_GENERIC
enabled in the kernel.
With CONFIG_PCI_HOST_GENERIC enabled PCIe host bridge is detected:
$ dmesg
pci-host-generic 4010000000.pcie: host bridge /pcie@10000000 ranges:
pci-host-generic 4010000000.pcie: IO 0x3eff0000..0x3effffff -> 0x00000000
pci-host-generic 4010000000.pcie: MEM 0x10000000..0x3efeffff -> 0x10000000
pci-host-generic 4010000000.pcie: MEM 0x8000000000..0xffffffffff -> 0x8000000000
pci-host-generic 4010000000.pcie: ECAM at [mem 0x4010000000-0x401fffffff] for [bus 00-ff]
pci-host-generic 4010000000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x10000000-0x3efeffff]
pci_bus 0000:00: root bus resource [mem 0x8000000000-0xffffffffff]
pci 0000:00:00.0: [1b36:0008] type 00 class 0x060000
$ lspci
00:00.0 Host bridge: Red Hat, Inc. QEMU PCIe Host bridge
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=eb01d42a77785ff96b6e66a2a2e7027fc6d78e4a
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Qemu for the aarch64 virt emulate an RTC PL031 device.
Enable the kernel support to allow setting the system time.
"date" now return the current time:
Sun Jul 5 20:38:50 UTC 2020
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
And rebase uboot patch.
Tested-by: Maeva Manuel <maeva.manuel@oss.nxp.com>
[Maeva: Tested on i.MX6Quad SabreAuto CPU1]
Signed-off-by: Julien Olivain <julien.olivain@oss.nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This makes the boot script set appropriate root parameters when it's
loaded from a NAND flash device.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The DCON driver for the platform is a staging driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The XO-1 laptop has a NAND flash and firmware capable of reading JFFS2
from it. Enable JFFS2 kernel support so that we'll be able to create
images capable of booting from the internal flash.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A couple of config symbols were mising that things we enable depend on.
Enable them.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This is the keyboard connected via the SP "security processor" on a
XO-1.75. XO-1 has a regular PC keyboard.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
XO-1 has an internal MTD device.
Also, CONFIG_MTD_SPI_NOR was set twice for XO-1.75. One copy is removed,
one remains.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A few conflicts had to be resolved:
- Version number and hash for mesa3d-headers/mesa3d
- Patches added in qemu, and the qemu version number
- The gnuconfig README.buildroot
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This patch adds support for the i.MX8M Nano EVK Board [1].
The final boot image is created from uboot and firmware binaries in post
image script board/freescale/common/imx/imx8-bootloader-prepare.sh
Note that this config is based on 4.19.35_1.1.0 ; hence, the kernel
configuration needs host-openssl to build.
[1] https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/evaluation-kit-for-the-i-mx-8m-nano-applications-processor:8MNANOD4-EVK
Signed-off-by: Stephane Viau <stephane.viau@oss.nxp.com>
Reviewed-by: Maeva Manuel <maeva.manuel@oss.nxp.com>
Reviewed-by: Julien Olivain <julien.olivain@oss.nxp.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
