When BR2_TARGET_OPTEE_OS=y, mkimage_fit_atf.sh is executed with two additional
variables so that the ITS file contains an additional node for the TEE binary.
Then the TEE binary will be packaged into the ITB in addition to TF-A and
U-Boot.
Signed-off-by: Thomas Perrot <thomas.perrot@bootlin.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Currently, when BR2_LINUX_KERNEL_INSTALL_TARGET=y is selected, issuing
a "saveenv" command in the U-Boot prompt may lead to rootfs corruption.
When BR2_LINUX_KERNEL_INSTALL_TARGET is not selected, then
board/freescale/common/imx/genimage.cfg.template is used as per the logic
inside board/freescale/common/imx/post-image.sh.
board/freescale/common/imx/genimage.cfg.template correctly puts the
rootfs at a safe offset.
With BR2_LINUX_KERNEL_INSTALL_TARGET=y, then
board/freescale/common/imx/genimage.cfg.template_no_boot_part or
board/freescale/common/imx/genimage.cfg.template_no_boot_part_spl
are used and no offset to the rootfs is given, which may cause U-Boot
environment area to write into the rootfs area, causing the rootfs
corruption.
Avoid this problem by placing the rootfs at an 8MB offset, just like
it is done in board/freescale/common/imx/genimage.cfg.
Tested on a imx6qp-wandboard and also on a custom imx6ull based board.
"saveenv" does not corrupt the rootfs anymore after this change.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
For the i.MX8 often an Image.gz is built. With these changes, if
BR2_LINUX_KERNEL_IMAGEGZ=y, the correct Image.gz file is now put into
the generated image instead of falling back to the non-existent zImage.
Signed-off-by: Hanspeter Portner <dev@open-music-kontrollers.ch>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Currently, only SPL is supported when BR2_LINUX_KERNEL_INSTALL_TARGET=y
is selected.
Support non-SPL case too.
This is needed for booting imx7d-sabresd, for example.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Pierre-Jean Texier <texier.pj2@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Almost identical as i.MX 8M Nano, with a couple of differences:
- different ATF load address [1]
- different entry point [2]
[1] e8e2703a30
[2] https://source.denx.de/u-boot/u-boot/-/blob/v2021.04-rc4/configs/imx8mp_evk_defconfig#L14
Signed-off-by: Stephane Viau <stephane.viau@oss.nxp.com>
Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
A few conflicts had to be resolved:
- Version number and hash for mesa3d-headers/mesa3d
- Patches added in qemu, and the qemu version number
- The gnuconfig README.buildroot
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
For some SoCs (i.e.: i.MX8M Nano for now), the DDR training firmware
in the boot image depends on the type of memory installed on a board
(LPDDR4, DDR4, etc...). The previous patch makes this firmware name
agnostic of the DDR type and uses ddr_fw.bin as a generic name. This
patch makes imx8-bootloader-prepare.sh use this generic name,
independently of the kind board DDR type.
Signed-off-by: Stephane Viau <stephane.viau@oss.nxp.com>
Reviewed-by: Maeva Manuel <maeva.manuel@oss.nxp.com>
Reviewed-by: Julien Olivain <julien.olivain@oss.nxp.com>
Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The default iamge size is 32MiB, which is quite low by today's standards.
Besides, the AArch64 kernels are relatively big, which leaves not much
room, if at all, for users to experiment on the default image.
Increase the vfat size to a more reasonable 64MiB.
Note that users who derive an in-tree defconfig for their own case will
allways hit any arbitarary size we put here, so they will anyway have to
also derive this template for their own use-cases.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Currently the volume-label for the vfat partition is a string with
the following pattern: 5934-861D.
Specify the volume-label as "boot" to make it easier to identify it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently the volume-label for the vfat partition is a string with
the following pattern: 5934-861D.
Specify the volume-label as "boot" to make it easier to identify it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Commit 3f8ace0028
("board/freescale/common/imx: add support for i.MX8") had its
conflicts incorrectly tweaked when applied to Buildroot. The
ahab-container.img is installed with this name (ahab-container.img) by
the imx-firmware package, and not mx8qm-ahab-container.img or
mx8qx-ahab-container.img.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Julien Olivain <juju@cotds.org>
Tested-by: Julien Olivain <juju@cotds.org>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
In board/freescale/common/imx/imx8-bootloader-prepare.sh, when
invoking mkimage_fit_atf.sh, the U-Boot DTB is passed as parameter, to
be included in the FIT image. This parameter usually comes from
BR2_ROOTFS_POST_SCRIPT_ARGS config option. The variable
BL33=u-boot.bin set in the invocation uses the u-boot image which is
including its embedded DTB. This means the U-Boot DTB is included
twice.
The upstream script mkimage_fit_atf.sh plus its Buildroot patch are
meant to use by default the nodtb variant and use the DTB in a
separate image. See [1] and [2].
The U-Boot default DTB which will be included in u-boot.bin image is
selected with U-Boot CONFIG_DEFAULT_DEVICE_TREE, or DEVICE_TREE
variable when invoking "make". If one of those option is not aligned
to the BR2_ROOTFS_POST_SCRIPT_ARGS config option, it's possible the
two included U-Boot DTBs are different. If such case happens, the
built-in DTB is always used, regardless of the other one, selected
with BR2_ROOTFS_POST_SCRIPT_ARGS.
For example, this case happens for TechNexion Pico Pi i.MX8M and
i.MX8MMini. Since the U-Boot defconfig assumes the nodtb version will
be used, it does not set the default DTB. The u-boot.bin will include
the fsl-imx8mm-evk instead. Including the wrong board DTB breaks the
USB and UMS commands (and possibly others). Since those boards does
not have SD card slots, a recovery serial download is needed at every
update.
This patch make sure that only the separate U-Boot DTB will be
included in the FIT image by using the nodtb variant.
[1] https://source.codeaurora.org/external/imx/imx-mkimage/tree/iMX8M/mkimage_fit_atf.sh?h=rel_imx_4.14.98_2.0.0_ga#n35
[2] https://git.busybox.net/buildroot/tree/package/imx-mkimage/0001-add-support-for-overriding-bl32-and-bl33-not-only-bl.patch?h=2019.11#n42
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
For boards like imx7d-pico, u-boot.img changes to u-boot-dtb.img in
U-Boot v2019.07. Therefore, we need to pick u-boot.img or u-boot-dtb.img
depending on the board configuration.
Just like was done in commit 52344e556f for the generic genimage
template, replace the U-Boot file name with UBOOTBIN, which is set
according to the BR2_TARGET_UBOOT_FORMAT_* option. We also need to set
the correct value for this variable for the u-boot.img and
u-boot-dtb.img cases.
While we're at it, rename the partition from 'u-boot-img' to 'u-boot',
to stay consistent with the generic genimage template.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
[Arnout: correct u-boot.img condition, rework commit log]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Modern U-Boot assumes a layout where the first partition is an ext2 and
the kernel and dtb can be found in /boot. In other words, a layout
without boot partition.
Add a genimage.cfg template for the freescale defconfigs with such a
layout.
For now, only the layout with SPL+u-boot.img is added. It's unlikely that
the u-boot.imx approach will be used.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
For the boot image creation for the i.MX8MM, the main differences with
i.MX8M are that there is no HDMI firmware image passed, and the ATF
load address is different.
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
The update of imx-mkimage in commit
c14d92d439
broke the imx8-bootloader-prepare.sh script for i.MX8M, used in
freescale_imx8mqevk_defconfig
The updated mkimage_fit_atf.sh script in imx-mkimage now needs
a ATF_LOAD_ADDR variable, which was set to 0x00910000 for i.MX8M.
Signed-off-by: Julien Olivain <juju@cotds.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Allow user to override the hardcoded dtb name by using
BR2_ROOTFS_POST_SCRIPT_ARGS.
The only user of this script, configs/freescale_imx8mqevk, is updated
accordingly.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for flashing the u-boot-dtb.imx binary in the SD card
when a target selects BR2_TARGET_UBOOT_FORMAT_DTB_IMX.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit adds a genimage template file that is used for i.MX8
platforms in the common i.MX post-image script.
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit adds an imx8-bootloader-prepare.sh script that will be
used by i.MX8 platforms to prepare their bootloader image.
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This commit makes the common post-image.sh script used by Freescale
platforms compatible with arm64:
- Support having DTBs in sub-folders
- Support a kernel image in the 'Image' format
Signed-off-by: Erik Larsson <karl.erik.larsson@gmail.com>
Signed-off-by: Christopher Dahlberg <crille.dahlberg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
In order to have a better hierarchy for the genimage scripts used by
NXP mx25, mx51, mx53, mx6, mx7 SoCs, let's place them inside the
board/freescale/common/imx/ directory.
This helps in creating a more natural separation between the mxs scripts
that are placed inside the board/freescale/common/mxs/ directory.
Suggested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add a standard genimage script for the MXS processors (MX23 and MX28).
Based on the common scripts for the other imx devices:
board/freescale/common/genimage.cfg.template
board/freescale/common/post-image.sh
This makes it easier to add new MX23/MX28 boards configurations into
Buildroot.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
For the boards imx6ulevk, imx6sabresd, mx25pdk, mx51evk, mx53loco,
warpboard:
* Replace genimage.cfg with a common Freescale genimage template named
genimage.cfg.template because they all use the same layout. The only
difference comes from the device tree blobs.
* Replace each post-image.sh script with a generic post-image.sh script
which is able to generate the right genimage.cfg depending on:
** the image type (zImage or uImage) from BR2_LINUX_KERNEL_UIMAGE
** the device tree blobs from BR2_LINUX_KERNEL_INTREE_DTS_NAME
** the rootfs type (ext2, ext3 or ext4) from BR2_TARGET_ROOTFS_EXT2
* Fix the readme.txt files accordingly
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
[Thomas: remove handling of rootfs type, using rootfs.ext2 in all cases
is fine, rootfs.ext3 and rootfs.ext4 are just symbolic links to it.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
