2022-12-19 09:57:10 +01:00
|
|
|
Starfive VisionFive2
|
|
|
|
|
====================
|
|
|
|
|
|
|
|
|
|
The VisionFive2 is a low-cost RISC-V 64-bit based platform, powered by a
|
|
|
|
|
Starfive JH7110 processor.
|
|
|
|
|
|
2023-02-11 23:47:55 +01:00
|
|
|
https://doc-en.rvspace.org/Doc_Center/visionfive_2.html
|
|
|
|
|
|
2022-12-19 09:57:10 +01:00
|
|
|
How to build
|
|
|
|
|
============
|
|
|
|
|
|
|
|
|
|
$ make visionfive2_defconfig
|
|
|
|
|
$ make
|
|
|
|
|
|
2024-04-14 21:06:44 +02:00
|
|
|
Once the build process is finished you will have two images
|
|
|
|
|
in the output/images/ directory:
|
|
|
|
|
- sdcard.img
|
|
|
|
|
- spi-nor.img
|
|
|
|
|
|
|
|
|
|
How to write the SPI NOR flash
|
|
|
|
|
=============================
|
|
|
|
|
|
|
|
|
|
If you have a booting device use u-boot and tftp:
|
|
|
|
|
|
|
|
|
|
# tftpboot 0x82000000 spi-nor.img
|
|
|
|
|
# sf probe
|
|
|
|
|
# sf update 0x82000000 0x0 {filesize}
|
|
|
|
|
|
|
|
|
|
Otherwise, follow the recovery instruction:
|
|
|
|
|
|
|
|
|
|
https://doc-en.rvspace.org/VisionFive2/Quick_Start_Guide/VisionFive2_SDK_QSG/recovering_bootloader%20-%20vf2.html
|
|
|
|
|
|
2022-12-19 09:57:10 +01:00
|
|
|
How to write the SD card
|
|
|
|
|
========================
|
|
|
|
|
|
|
|
|
|
Copy the bootable "sdcard.img" onto an SD card with "dd":
|
|
|
|
|
|
|
|
|
|
$ sudo dd if=output/images/sdcard.img of=/dev/sdX
|
|
|
|
|
|
|
|
|
|
Preparing the board
|
|
|
|
|
===================
|
|
|
|
|
|
|
|
|
|
Connect a TTL UART cable to pin 6 (GND), 8 (TX) and 10 (RX).
|
|
|
|
|
|
2024-04-14 21:06:44 +02:00
|
|
|
Use the correct mode for booting:
|
|
|
|
|
- SD card RGPIO_0=1, GRPIO_1=0
|
|
|
|
|
- SPI NOR flash RGPIO_0=1, GRPIO_1=1
|
|
|
|
|
|
|
|
|
|
Note that Buildroot puts the bootloader both in SPI NOR and on the SD card,
|
|
|
|
|
so after flashing as instructed above, either boot mode should work.
|
2024-02-08 22:15:17 +01:00
|
|
|
|
|
|
|
|
https://doc-en.rvspace.org/VisionFive2/Quick_Start_Guide/VisionFive2_SDK_QSG/boot_mode_settings.html
|
|
|
|
|
|
2022-12-19 09:57:10 +01:00
|
|
|
Insert your SD card.
|
|
|
|
|
|
|
|
|
|
Power-up the board using an USB-C cable.
|
